Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
NM27T0E _51 Engine / Hybrid System _053572 1GR-FE ENGINE CONTROL _0260097 SFI SYSTEM UN GENERAL/CONTROL/DETAILS F

1GR-FE ENGINE CONTROL  SFI SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Intake Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor has a built-in hot-wire to directly detect the intake air mass.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Crankshaft Position Sensor [Rotor Teeth] Pick-up Coil Type [36 - 2] 1 This sensor detects the engine speed and performs cylinder identification.
Camshaft Position Sensor for Intake [Rotor Teeth] Magnetic Resistance Element (MRE) Type [3] 2 (1 each bank) This sensor performs cylinder identification.
Camshaft Position Sensor for Exhaust [Rotor Teeth] Magnetic Resistance Element (MRE) Type [3] 2 (1 each bank) This sensor performs cylinder identification.
Accelerator Pedal Position Sensor Linear (Non-contact) Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Throttle Position Sensor Linear (Non-contact) Type 1 This sensor detects the throttle valve opening angle.
Knock Control Sensor (Bank 1 and Bank 2) Built-in Piezoelectric Type (Non-resonant Type/ Flat Type) 2 (1 each bank) This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
Air Fuel Ratio Sensor (Bank 1, Sensor 1) (Bank 2, Sensor 1) Heated Type (Planar Type) 2 (1 each bank) As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emission. However, it detects the oxygen concentration in the exhaust emission linearly.
Oxygen Sensor (Bank 1, Sensor 2) (Bank 2, Sensor 2) Heated Type (Cup Type) 2 (1 each bank) This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Fuel Injector Assembly 12-hole Type 6 The fuel injector assembly is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.



SYSTEM CONTROL


a.

The engine control system has the following features. The ECM controls these systems:

System Outline
Sequential Multiport Fuel Injection (SFI)
·

An L-type SFI system directly detects the intake air mass with a hot-wire type mass air flow meter.

·

The fuel injection system is a sequential multiport fuel injection system.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signals to the igniters.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort, the throttle valve opening control request from the ECM, and the condition of the engine and the vehicle.
Dual Variable Valve Timing-intelligent (Dual VVT-i) Regulates operation of the intake and exhaust camshafts to ensure an optimal valve timing in accordance with the engine condition.
Fuel Pump Control
·

Based on signals from the ECM, the fuel pump control ECU controls the fuel pump in 3 stages.

·

The fuel pump is stopped when the SRS airbag is deployed in a frontal, side, or side rear collision.


Air Conditioning Cut-off Control By turning the air conditioning compressor assembly on or off in accordance with the engine condition, driveability is maintained.
Starter Control Once the engine switch is pushed, this control continues to operate the starter until the engine has started.
Air Fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Diagnosis When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section.
Fail-safe When the ECM detects a malfunction, the ECM stops or controls the engine in accordance with the data already stored in memory.
Brake Override System The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the activation conditions and inspection method, refer to the Repair Manual.)



FUNCTION


a.

Dual VVT-i System

i.

The Dual VVT-i system is designed to control the intake and exhaust camshaft within a range of 40° and 35° respectively (of crankshaft angle) to provide valve timing that is optimally suited to the engine operating conditions. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W102481E01
4.128,0.039 4.349,0.232 0.221,0.193 10 *1 4.128,0.278 4.349,0.470 0.221,0.193 10 *2 4.128,0.502 4.349,0.695 0.221,0.193 10 *3 4.128,0.74 4.349,0.933 0.221,0.193 10 *4 4.128,0.978 4.349,1.171 0.221,0.193 10 *5 4.128,1.286 4.349,1.479 0.221,0.193 10 *6 4.128,1.805 4.349,1.998 0.221,0.193 10 *7 4.128,2.155 4.349,2.348 0.221,0.193 10 *8 4.128,2.505 4.349,2.698 0.221,0.193 10 *9 4.128,2.87 4.414,3.062 0.286,0.193 10 *10 4.922,1.898 5.208,2.091 0.286,0.193 10 *11 6.178,1.924 6.464,2.117 0.286,0.193 10 *12 6.193,2.456 6.478,2.649 0.286,0.193 10 *13

Text in Illustration
*1 Camshaft Timing Oil Control Valve Assembly (Exhaust RH) *2 Camshaft Timing Oil Control Valve Assembly (Intake RH)
*3 Camshaft Position Sensor (Exhaust RH) *4 Engine Coolant Temperature Sensor
*5 Camshaft Timing Oil Control Valve Assembly (Intake LH) *6 Camshaft Position Sensor (Exhaust LH)
*7 Camshaft Timing Oil Control Valve Assembly (Exhaust LH) *8 Camshaft Position Sensor (Intake LH)
*9 Crankshaft Position Sensor *10 Camshaft Position Sensor (Intake RH)
*11 ECM *12 Intake Air Flow Meter Sub-assembly
*13 Throttle Position Sensor - -

W102341E07
3,0.656 2.75,0.521 2.75,0.521 2.656,0.521 false 2.635,0.74 2.229,0.354 2.229,0.354 2.052,0.354 false 2.01,2.656 1.781,2.875 1.781,2.875 1.635,2.875 false 3.719,2.708 4.156,2.99 4.156,2.99 4.385,2.99 false 3.323,0.875 3.76,0.427 3.76,0.427 4.052,0.427 false 3.104,0.448 3.385,0.656 0.281,0.208 10 false 11° 2.521,0.427 2.802,0.635 0.281,0.208 10 false 4° 2.135,0.594 2.417,0.802 0.281,0.208 10 false 29° 1.521,2.292 1.802,2.5 0.281,0.208 10 false 71° 2.115,3.031 2.396,3.24 0.281,0.208 10 false 31° 4.094,2.552 4.406,2.75 0.313,0.198 10 false 60° 3.448,3.125 3.76,3.323 0.313,0.198 10 false 25° 3.656,0.698 3.969,0.896 0.313,0.198 10 false 39° 0.625,0.271 2.104,0.927 1.479,0.656 10 false Intake VVT-i Operation Range 0.219,2.781 1.646,3.427 1.427,0.646 10 false Intake VVT-i Operation Range 4.427,2.906 6.073,3.563 1.646,0.656 10 false Exhaust VVT-i Operation Range 4.094,0.354 5.74,1.01 1.646,0.656 10 false Exhaust VVT-i Operation Range 4.823,1.688 6.885,2.042 2.063,0.354 10 false : Exhaust valve opening angle 4.833,1.302 6.802,1.656 1.969,0.354 10 false : Intake valve opening angle 2.802,0.333 3.167,0.646 0.365,0.313 10 false TDC 2.792,3.344 3.156,3.656 0.365,0.313 10 false BDC


ii.

The VVT-i system delivers excellent benefits in the different operating conditions as shown in the table below.

Operation State Objective Effect
During Idling
W132964E01
0.448,0.073 1.406,0.479 0.958,0.406 10 false Earliest Timing (EX) 2.135,0.073 3.094,0.479 0.958,0.406 10 false Latest Timing (IN) 1.604,0.208 1.948,0.469 0.344,0.26 10 false TDC 1.594,1.854 1.938,2.115 0.344,0.26 10 false BDC 0.792,0.958 1.135,1.219 0.344,0.26 10 false EX 2.438,0.979 2.781,1.24 0.344,0.26 10 false IN

Eliminating overlap reduces blow back to the intake side.
·

Stabilized idling speed

·

Better fuel economy


At Light Load
W132965E01
0.292,0.198 1.219,0.583 0.927,0.385 10 false Earliest Timing (EX) 2.396,0.177 3.323,0.563 0.927,0.385 10 false Latest Timing (IN) 1.604,0.229 2.063,0.427 0.458,0.198 10 false TDC 1.604,1.813 2.063,2.01 0.458,0.198 10 false BDC 0.802,1.063 1.26,1.26 0.458,0.198 10 false EX 2.5,1.052 2.958,1.25 0.458,0.198 10 false IN

Eliminating overlap reduces blow back to the intake side. Engine stability is ensured
At Medium Load
W132966E01
0.427,0.167 1.188,0.552 0.76,0.385 10 false To Advance Side (IN) 2.25,0.167 2.938,0.552 0.688,0.385 10 false To Retard Side (EX) 1.573,0.25 2.031,0.448 0.458,0.198 10 false TDC 1.583,1.865 2.042,2.063 0.458,0.198 10 false BDC 0.854,1.052 1.313,1.25 0.458,0.198 10 false EX 2.396,1.042 2.854,1.24 0.458,0.198 10 false IN

Increasing overlap increases internal EGR, reducing pumping losses.
·

Better fuel economy

·

Improved emission control


In Low to Medium Speed Range with Heavy Load
W132967E01
0.552,1.438 1.198,1.969 0.646,0.531 10 false To Retard Side (EX) 2.292,1.438 3,1.979 0.708,0.542 10 false To Advance Side (IN) 1.563,1.823 1.969,2.031 0.406,0.208 10 false BDC 1.542,0.219 1.948,0.427 0.406,0.208 10 false TDC 0.729,0.958 1.135,1.167 0.406,0.208 10 false EX 2.406,0.979 2.813,1.188 0.406,0.208 10 false IN

Advancing the intake valve closing timing improves volumetric efficiency. Improved torque in low to medium speed range
In High Speed Range with Heavy Load
W132968E01
2.292,1.406 3.01,1.771 0.719,0.365 10 false To Advance Side (EX) 0.531,1.396 1.146,1.781 0.615,0.385 10 false To Retard Side (IN) 1.594,0.219 2,0.438 0.406,0.219 10 false TDC 0.76,0.948 1.167,1.167 0.406,0.219 10 false EX 2.406,0.958 2.813,1.177 0.406,0.219 10 false IN 1.563,1.813 1.969,2.031 0.406,0.219 10 false BDC

Retarding the intake valve closing timing improves volumetric efficiency. Improved output
At Low Temperatures
W132964E01
0.448,0.073 1.406,0.479 0.958,0.406 10 false Earliest Timing (EX) 2.135,0.073 3.094,0.479 0.958,0.406 10 false Latest Timing (IN) 1.604,0.208 1.948,0.469 0.344,0.26 10 false TDC 1.594,1.854 1.938,2.115 0.344,0.26 10 false BDC 0.792,0.958 1.135,1.219 0.344,0.26 10 false EX 2.438,0.979 2.781,1.24 0.344,0.26 10 false IN

Eliminating overlap to reduce blow back to the intake side stabilizes the idling speed at fast idle.
·

Stabilized fast idle speed

·

Better fuel economy


·

Starting Engine

·

Stopping Engine


W132964E01
0.448,0.073 1.406,0.479 0.958,0.406 10 false Earliest Timing (EX) 2.135,0.073 3.094,0.479 0.958,0.406 10 false Latest Timing (IN) 1.604,0.208 1.948,0.469 0.344,0.26 10 false TDC 1.594,1.854 1.938,2.115 0.344,0.26 10 false BDC 0.792,0.958 1.135,1.219 0.344,0.26 10 false EX 2.438,0.979 2.781,1.24 0.344,0.26 10 false IN

Eliminating overlap minimize blow back to the intake side. Improved startability



b.

Electronic Throttle Control System-intelligent (ETCS-i)

i.

The ETCS-i is used, providing excellent throttle control in all the operating ranges. The accelerator cable has been discontinued, and an accelerator pedal position sensor has been provided on the accelerator pedal.


ii.

In the conventional throttle body, the throttle valve opening is determined by the amount of the accelerator pedal effort. In contrast, the ETCS-i uses the ECM to calculate the optimal throttle valve opening that is appropriate for the respective driving condition and uses a throttle control motor to control the opening.


iii.

The ETCS-i controls the idle speed, Brake Control system, cruise control system*1 and dynamic radar cruise control system*2.

*1: Models with cruise control system

*2: Models with dynamic radar cruise control system



iv.

In case of an abnormal condition, this system switches to the limp mode.

W102377E09
3,1.073 3.344,0.344 3.344,0.344 3.635,0.344 false 4.385,4.094 4.271,4.094 4.271,4.094 4.219,3.833 false 0.51,5.469 2.031,5.854 1.521,0.385 10 false Fuel Injector Assembly 0.448,4.813 1.948,5.146 1.5,0.333 10 false Ignition Coil Assembly 3.063,4.094 3.458,4.417 0.396,0.323 10 false ECM 5.146,2.573 6.333,2.885 1.188,0.313 10 false Skid Control ECU 0.521,2.552 1.854,2.885 1.333,0.333 10 false Mass Air Flow Meter 4.521,1.01 5.969,1.375 1.448,0.365 10 false Throttle Control Motor 0.26,1.188 1.458,1.833 1.198,0.646 10 false Accelerator Pedal Position Sensor 4.677,5.5 6.74,5.885 2.063,0.385 10 false Millimeter Wave Radar Sesnor*2 0.396,3.219 2,3.552 1.604,0.333 10 false Cruise Control Switch*1 0.823,3.646 1.802,3.979 0.979,0.333 10 false Main Switch 0.729,4.115 1.75,4.448 1.021,0.333 10 false Mode Switch*2 3.708,0.271 4.615,0.594 0.906,0.323 10 false Throttle Valve 0.333,6.25 4.125,6.563 3.792,0.313 10 false *1: Models with cruise control system 4.708,3.583 6.854,3.958 2.146,0.375 10 false Power Management Control ECU 4.99,4.854 6.458,5.219 1.469,0.365 10 false Driving Support ECU*2 4.823,3.104 5.76,3.49 0.938,0.385 10 false CAN (V1 Bus) 5.813,4.333 6.75,4.719 0.938,0.385 10 false CAN (V2 Bus) 4.427,4.01 5.583,4.51 1.156,0.5 10 false CAN (Power Management Bus*3), V1Bus*4 0.333,6.531 4.125,6.844 3.792,0.313 10 false *2: Models with dynamic radar cruise control system 3.75,6.25 7.156,6.583 3.406,0.333 10 false *3: Models with manual transmission 3.75,6.5 7.156,6.833 3.406,0.333 10 false *4: Models with automatic transmission



c.

Fuel Pump Control

i.

The fuel pump is controlled by the fuel pump control ECU based on signals from the ECM. The fuel pump control has a fuel cut control. The fuel cut control stops the fuel pump when any of the Supplemental Restraint System (SRS) airbags have deployed.



d.

Starter Control

i.

Once the engine switch is pressed, this function operates the starter until the engine starts, provided that the clutch pedal is depressed.


ii.

This prevents application of the starter for an inadequate length of time and also prevents the engine from being cranked after it has started.




CONSTRUCTION


a.

Air Fuel Ratio Sensor and Oxygen Sensor

i.

A planar type air fuel ratio sensor and a cup type oxygen sensor are used. The basic construction of the oxygen sensor and the air fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, in accordance with the different types of heater construction used.


ii.

The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate the sensor element with a heater, thus improving the warmup performance of the sensor.


iii.

The cup type oxygen sensor contains a sensor element that surrounds the heater.

W102378E04
0.552,0.156 3.427,3.667 2.875,3.51 3.802,0.156 6.677,3.667 2.875,3.51 2.375,2.313 2.167,1.938 2.167,1.938 2.052,1.938 true 2.438,2.219 2.438,1.719 2.438,1.719 2.333,1.719 true 2.615,2.188 2.615,1.948 2.615,1.948 2.719,1.948 true 2.604,2.51 2.854,2.271 2.854,2.271 2.99,2.271 true 2.719,3.073 2.854,2.938 2.854,2.938 2.958,2.938 true 2.51,3.156 2.51,3.354 2.51,3.354 2.625,3.354 true 2.552,2.823 2.188,3.302 2.188,3.302 1.875,3.302 true 2.458,2.813 2.083,3.292 true 5.781,3.125 5.635,3.365 5.635,3.365 5.49,3.365 true 5.76,2.146 5.76,1.802 5.76,1.802 5.615,1.802 true 6.083,2.135 6.083,1.802 6.083,1.802 6.375,1.802 true 6.188,2.125 6.188,1.813 true 5.896,2.156 5.896,1.344 5.896,1.344 6.021,1.344 true 2.177,1.646 2.385,1.854 0.208,0.208 10 false *1 1.896,1.865 2.104,2.073 0.208,0.208 10 false *2 2.74,1.875 2.948,2.083 0.208,0.208 10 false *2 3.021,2.198 3.229,2.406 0.208,0.208 10 false *3 5.458,1.729 5.667,1.938 0.208,0.208 10 false *3 2.979,2.844 3.188,3.052 0.208,0.208 10 false *4 2.646,3.281 2.854,3.49 0.208,0.208 10 false *6 1.698,3.229 1.906,3.438 0.208,0.208 10 false *5 6.052,1.271 6.26,1.479 0.208,0.208 10 false *4 6.385,1.729 6.594,1.938 0.208,0.208 10 false *5 5.323,3.292 5.531,3.5 0.208,0.208 10 false *6 0.646,0.24 0.917,0.479 0.271,0.24 12 false *A: 0.646,0.24 0.917,0.479 0.271,0.24 12 false *A: 3.927,0.24 4.198,0.479 0.271,0.24 12 false *B:

Text in Illustration
*A Planar Type Air Fuel Ratio Sensor *B Cup Type Oxygen Sensor
*1 Diffusion Resistance Layer *2 Alumina
*3 Atmosphere *4 Heater
*5 Platinum Electrode *6 Sensor Element (Zirconia)


iv.

As illustrated below, the conventional oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air fuel ratio (14.7:1). In contrast, the air fuel ratio sensor data is approximately proportionate to the existing air fuel ratio. The air fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air fuel ratio has been improved. The air fuel ratio sensor data can be viewed using an the Global Techstream.

W132987E01
1.938,0.458 2.24,0.458 2.24,0.458 2.74,1.292 false 3.635,1.979 3.875,0.615 3.875,0.615 4.188,0.615 false 0.958,0.354 2.094,0.583 1.135,0.229 10 false Oxygen Sensor 3.229,4.125 4.365,4.354 1.135,0.229 10 false Air Fuel Ratio 0.219,4.51 5.656,4.813 5.438,0.302 10 false *: This value is calculated internally in the ECM and is not an ECM terminal voltage. 0.188,1.854 1.865,2.438 1.677,0.583 10 false Air Fuel Ratio Sensor Output* (Data Displayed on the Global Techstream) 5.292,1.958 6.292,2.458 1,0.5 10 false Oxygen Sensor Output 4.271,0.51 5.865,0.802 1.594,0.292 10 false Air Fuel Ratio Sensor 1.833,0.792 2.198,1.052 0.365,0.26 10 false (V) 1.635,0.969 2,1.229 0.365,0.26 10 false 4.2 1.646,3.406 2.01,3.667 0.365,0.26 10 false 2.2 2.073,3.813 2.719,4.094 0.646,0.281 10 false 11 (Rich) 3.344,3.802 3.708,4.063 0.365,0.26 10 false 14.7 5.01,3.802 5.677,4.063 0.667,0.26 10 false 19 (Lean) 5.323,3.438 5.688,3.698 0.365,0.26 10 false 0.1 5.156,0.813 5.521,1.073 0.365,0.26 10 false (V) 5.365,0.969 5.729,1.229 0.365,0.26 10 false 1



b.

Intake Air Flow Meter Sub-assembly

i.

This Intake Air Flow Meter Sub-assembly, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.


ii.

This Intake Air Flow Meter Sub-assembly has a built-in intake air temperature sensor.

W132981E01
3.802,0.583 6.281,3.417 2.479,2.833 4.427,2.188 4.615,2.188 4.615,2.188 4.844,1.771 true 5.104,1.813 5.281,2.167 5.281,2.167 5.469,2.167 true 4.938,1.844 5.219,2.552 5.219,2.552 5.406,2.552 true 2.146,0.625 2.302,0.823 0.156,0.198 10 false A 2.188,3.01 2.344,3.208 0.156,0.198 10 false A 3.875,0.635 4.031,0.833 0.156,0.198 10 false *a 4.26,2.177 4.417,2.375 0.156,0.198 10 false *1 5.438,2.49 5.594,2.688 0.156,0.198 10 false *3 5.49,2.083 5.646,2.281 0.156,0.198 10 false *2

Text in Illustration
*1 Platinum Hot-wire Element *2 Intake Air Temperature Sensor
*3 Temperature Sensing Element - -
*a A - A Cross Section - -
V100135

Air Flow - -



c.

Crankshaft Position Sensor

i.

A pick-up coil type crankshaft position sensor is used. The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crankshaft position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top-dead-center.

W102485E04
5.271,1.188 5.323,1.802 5.323,1.802 5.594,1.802 false 0.958,2.073 1.167,2.073 1.167,2.073 1.573,1.594 true 1.813,2.479 1.99,2.479 1.99,2.479 2.396,1.24 true 3.865,1.677 4.479,2.01 0.615,0.333 10 false 10° CA 3.729,0.094 7.063,0.469 3.333,0.375 10 false Crankshaft Position Sensor Signal Plate (720° CA) 5.625,1.698 6.719,2.094 1.094,0.396 10 false 2 Teeth Missing 0.063,1.26 0.521,1.917 0.458,0.656 10 false Engine Front 0.115,1.948 0.979,2.302 0.865,0.354 10 false Timing Rotor 0.104,2.365 1.896,2.708 1.792,0.344 10 false Crankshaft Position Sensor



d.

Cam Position Sensor

i.

Magnetic Resistance Element (MRE) type cam position sensors (intake and exhaust) are used. To detect each cam (intake) position, a timing rotor that is secured to the camshaft (intake) in front of the camshaft timing gear assembly is used to generate 6 (3 Hi Output, 3 Lo Output) pulses for every 2 revolutions of the crankshaft. The timing rotor for each camshaft (exhaust) is part of the respective camshaft.

W100688E24
4.302,0.26 4.688,0.26 4.688,0.26 5.135,0.604 true 1.104,2.583 1.5,2.583 1.5,2.583 1.958,1.927 true 2.896,2.531 2.573,2.531 2.573,2.531 2.438,2.094 true 5.635,2.677 5.208,2.677 5.208,2.677 4.99,1.854 true 0.281,2.49 1.177,2.833 0.896,0.344 10 false Timing Rotor 5.698,2.594 6.594,2.885 0.896,0.292 10 false Timing Rotor 2.938,2.458 4.229,3 1.292,0.542 10 false Cam Position Sensor (Intake RH) 2.083,0.167 4.302,0.469 2.219,0.302 10 false Cam Position Sensor (Exhaust RH) 0.167,3.01 2.208,3.396 2.042,0.385 10 false Sensor Output Waveforms 3.146,3.177 5.844,3.469 2.698,0.292 10 false Cam Position Sensor Signal Plate (720° CA) 0.229,3.792 1.167,4.365 0.938,0.573 10 false Cam Position Sensor Signal 0.198,5.219 1.396,5.771 1.198,0.552 10 false Crankshaft Position Sensor Signal 1.271,4.833 1.563,5.021 0.292,0.188 10 false 0 V 1.271,5.802 1.563,5.99 0.292,0.188 10 false 0 V 2.135,6.573 2.667,6.771 0.531,0.198 10 false 10° CA 3,5.042 3.594,5.198 0.594,0.156 10 false 360° CA 2.375,4.427 2.969,4.583 0.594,0.156 10 false 180° CA 4.979,4.438 5.573,4.594 0.594,0.156 10 false 120° CA 5.677,3.75 6.271,3.906 0.594,0.156 10 false 120° CA 3.083,3.76 3.604,3.917 0.521,0.156 10 false 60° CA 3.438,4.646 3.958,4.802 0.521,0.156 10 false 60° CA 4.125,3.75 4.719,3.906 0.594,0.156 10 false 180° CA 5.083,5.042 5.719,5.198 0.635,0.156 10 false 360° CA


ii.

The MRE type cam position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the different shapes (protruded and non-protruded portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the cam position based on this output voltage.

W100681E25
4.49,4.781 4.49,5.156 true 4.688,3.99 4.792,3.229 4.792,3.229 4.979,3.229 true 0.26,0.24 1.594,0.615 1.333,0.375 10 false Wiring Diagram 0.26,2.438 5.073,2.865 4.813,0.427 10 false MRE Type and Pick-up Coil Type Output Waveform Image Comparison 0.771,1.552 1.677,1.948 0.906,0.396 10 false Timing Rotor 1.833,1.365 3.083,2.198 1.25,0.833 10 false Camshaft Position Sensor (Intake RH) 3.667,0.823 4.094,1.135 0.427,0.313 10 false VCV+ 3.677,1.146 4.104,1.469 0.427,0.323 10 false VV1+ 3.677,1.479 4.094,1.833 0.417,0.354 10 false VV1- 4.813,1.052 5.354,1.448 0.542,0.396 10 false ECM 0.542,3.177 1.021,3.99 0.479,0.813 10 false Engine Speed 3.563,3.177 4.052,3.969 0.49,0.792 10 false Engine Speed 0.521,4.792 1.031,5.521 0.51,0.729 10 false Sensor Output 3.573,4.51 4.052,5.375 0.479,0.865 10 false Sensor Output 1.625,5.479 2.594,5.792 0.969,0.313 10 false MRE Type 4.875,5.49 6.094,5.792 1.219,0.302 10 false Pick-up Type 2.344,5.208 3.354,5.573 1.01,0.365 10 false Digital Output 6.073,4.833 7.083,5.26 1.01,0.427 10 false Analog Output 4.156,5.167 5.5,5.469 1.344,0.302 10 false No Detection Area 5.01,3.125 6.292,3.5 1.281,0.375 10 false No Detection Area



e.

Knock Control Sensor (Flat Type)

i.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

*: The term "Knock" or "Knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "Knock" or "Knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.



ii.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from approximately 6 kHz to 15 kHz). It has the following features:


iii.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability has been increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100047E46
3.865,1.354 3.74,1.354 3.74,1.354 3.594,1.594 false 5.49,2.198 5.229,2.198 5.229,2.198 5.115,2.083 false 3.99,1.656 3.906,1.656 3.906,1.656 3.865,1.979 false 3.979,0.792 6.24,1.135 2.26,0.344 10 false Detection Band of Resonant Type 4.042,1.552 5.958,1.854 1.917,0.302 10 false Detection Band of Flat Type 3.083,2.333 4.083,2.646 1,0.313 10 false Frequency 1.198,1.26 1.76,1.646 0.563,0.385 10 false Voltage 1.552,0.417 1.802,0.719 0.25,0.302 10 false (V) 5.083,2.333 5.531,2.656 0.448,0.323 10 false (Hz) 3.885,1.25 4.115,1.49 0.229,0.24 10 false *1 5.531,2.094 5.771,2.344 0.24,0.25 10 false *2 0.24,2.729 4.292,3.104 4.052,0.375 10 false *1: Resonance characteristic of conventional type (resonant) 0.24,3.135 4.094,3.521 3.854,0.385 10 false *2: Resonance characteristic of flat type (non-resonant) 0.229,0.052 3.344,0.406 3.115,0.354 10 false - Characteristics of Knock Control Sensor -


iv.

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt exists in the center of the sensor.


v.

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and the piezoelectric element.


vi.

An open/short circuit detection resistor is integrated in the sensor. When the ignition switch is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W100048E77
1.448,0.802 1.25,0.802 1.25,0.802 0.948,1.5 true 1.031,1.625 1.438,2.26 1.438,2.26 1.604,2.26 true 0.958,1.708 1.438,2.719 1.438,2.719 1.656,2.719 true 2.313,3.927 2.052,3.927 2.052,3.927 1.188,5.333 true 1.906,5.281 2.5,4.438 2.5,4.438 2.771,4.438 true 2.156,1.698 2.563,2.146 2.563,2.146 2.771,2.146 false 6.063,0.708 5.875,0.708 5.875,0.708 5.354,1.302 true 6.073,1.833 5.833,1.833 5.833,1.833 5.417,1.323 true 0.865,3.146 3.427,3.5 2.563,0.354 10 false Flat Type (Non-resonant Type) 4.375,3.177 7.156,3.521 2.781,0.344 10 false Conventional Type (Resonant Type) 6.115,1.76 7.156,2.104 1.042,0.344 10 false Vibration Plate 6.104,0.625 7.052,1.25 0.948,0.625 10 false Piezoelectric Element 1.698,2.635 3.104,2.969 1.406,0.333 10 false Piezoelectric Element 2.365,3.844 3.865,4.135 1.5,0.292 10 false Piezoelectric Element 2.844,2.083 4.052,2.625 1.208,0.542 10 false Open Circuit Detection Resistor 2.802,4.354 4.01,4.917 1.208,0.563 10 false Open Circuit Detection Resistor 1.458,0.719 2.385,1.01 0.927,0.292 10 false Steel Weight 1.646,2.177 2.281,2.427 0.635,0.25 10 false Insulator 4.24,4.073 4.646,4.229 0.406,0.156 10 false ECM 4.365,4.354 4.667,4.542 0.302,0.188 10 false 5 V 1.958,5.271 2.563,5.5 0.604,0.229 10 false 200 kΩ 4.521,4.708 5.125,4.938 0.604,0.229 10 false 200 kΩ 0.677,5.979 2.781,6.281 2.104,0.302 10 false Flat Type Knock Control Sensor 6.042,5.094 6.229,5.281 0.188,0.188 10 false IC 3.75,5.042 4.177,5.333 0.427,0.292 10 false KNK1 3.74,5.698 4.167,6 0.427,0.302 10 false EKNK


vii.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W100049E21
2.469,1.74 2.781,1.74 2.781,1.74 3.125,1.594 true 1.49,1.302 2.781,1.302 2.781,1.302 3.177,1.438 true 1.906,0.875 2.458,0.875 2.458,0.875 3.135,1.292 true 1.74,0.781 1.896,0.938 0.156,0.156 10 false *1 1.333,1.188 1.5,1.375 0.167,0.188 10 false *2 2.302,1.635 2.458,1.813 0.156,0.177 10 false *3

Text in Illustration
*1 Steel Weight *2 Inertia
*3 Piezoelectric Element - -


viii.

These knock control sensors are mounted in the specific directions and angles as illustrated. To prevent the right and left bank connectors from being interchanged, make sure to install each sensor in its prescribed direction.

W102379E02
3.25,0.792 2.906,0.458 2.906,0.458 2.677,0.458 true 3.906,0.802 4.24,0.292 4.24,0.292 4.438,0.292 true 2.521,0.354 2.698,0.583 0.177,0.229 10 false *1 4.458,0.188 4.667,0.417 0.208,0.229 10 false *2

Text in Illustration
*1 Knock Control Sensor (KNK1) *2 Knock Control Sensor (KNK2)
V100135

Engine Front
V100137

Knock Control Sensor Mounting Direction



f.

Throttle Position Sensor

i.

A non-contact type throttle position sensor is used. This sensor uses a Hall IC, which is mounted on the throttle body.


ii.

The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals and outputs them as throttle valve effort to the ECM.


iii.

The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angles into electric signals with two differing characteristics and outputs them to the ECM.

W132969E01
5.323,1.833 5.625,0.781 5.625,0.781 5.917,0.781 true 5.365,1.948 5.792,1.344 5.792,1.344 6.083,1.344 true 1.198,4.948 1.552,4.25 1.552,4.25 1.844,4.25 true 0.896,4.177 1.083,4.177 1.083,4.177 1.125,4.635 true 0.49,6.167 0.354,6.167 0.354,6.167 0.656,5.708 true 1.208,5.5 1.49,6.219 1.49,6.219 1.781,6.219 true 5.948,0.698 6.542,1.094 0.594,0.396 10 false Magnetic Yoke 0.521,6.073 1.521,6.469 1,0.396 10 false Magnetic Yoke 6.115,1.26 6.708,1.458 0.594,0.198 10 false Hall IC 1.865,4.177 2.458,4.375 0.594,0.198 10 false Hall IC 1.823,6.125 2.417,6.323 0.594,0.198 10 false Hall IC 4.771,3.344 6.667,3.604 1.896,0.26 10 false Throttle Position Sensor 0.229,6.469 2.125,6.729 1.896,0.26 10 false Throttle Position Sensor 0.406,4.083 1,4.281 0.594,0.198 10 false Magnet 1.781,4.833 2.229,5.031 0.448,0.198 10 false VTA1 1.792,5.146 2.24,5.344 0.448,0.198 10 false E 1.792,5.427 2.24,5.625 0.448,0.198 10 false VC 1.792,5.74 2.24,5.938 0.448,0.198 10 false VTA2 4.385,4.635 4.833,4.833 0.448,0.198 10 false VTA2 5.354,5.25 5.802,5.448 0.448,0.198 10 false VTA1 2.531,5.156 2.979,5.354 0.448,0.198 10 false ECM 4.021,4.438 4.156,4.625 0.135,0.188 10 false 5 4.021,5.646 4.156,5.833 0.135,0.188 10 false 0 3.781,4.135 4.052,4.323 0.271,0.188 10 false (V) 3.594,5 4.104,5.406 0.51,0.406 10 false Output Voltage 4.479,6.365 6.375,6.625 1.896,0.26 10 false Throttle Valve Opening Angle 3.781,6.052 4.615,6.271 0.833,0.219 10 false Fully Closed 6.177,6.052 7.01,6.271 0.833,0.219 10 false Fully Open



g.

Accelerator Pedal Position Sensor

i.

This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.


ii.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


iii.

This accelerator pedal position sensor includes 2 Hall ICs and circuits for the main and sub signals. It converts the accelerator pedal depressed angles into electric signals with two differing characteristics and outputs them to the ECM.

W100142E47
1.146,1.969 1.615,0.625 1.615,0.625 1.896,0.625 true 2.229,2.583 1.938,3.313 1.938,3.313 1.604,3.313 true 4.573,1.156 4.49,0.625 4.49,0.625 4.271,0.625 true 4.438,1.542 3.698,1.292 3.698,1.292 3.5,1.292 true 4.438,2.146 3.698,2.396 3.698,2.396 3.5,2.396 true 2.063,2.052 1.5,2.906 1.5,2.906 1.333,2.906 true 4.615,2.688 4.74,2.958 4.74,2.958 4.573,2.958 true 3.302,3.302 5.76,3.719 2.458,0.417 10 false Accelerator Pedal Position Sensor 3.052,1.188 3.531,1.542 0.479,0.354 10 false Hall IC 3.74,0.51 4.281,0.917 0.542,0.406 10 false Magnet 3.031,2.292 3.51,2.677 0.479,0.385 10 false Hall IC 1.177,4.115 1.469,4.521 0.292,0.406 10 false (V) 1.49,4.281 1.677,4.552 0.188,0.271 10 false 5 0.927,5.177 1.479,5.99 0.552,0.813 10 false Output Voltage 1.5,5.99 1.667,6.25 0.167,0.26 10 false 0 0.771,6.292 1.646,6.688 0.875,0.396 10 false Fully Closed 5.156,6.302 6.073,6.677 0.917,0.375 10 false Fully Open 2.24,6.313 4.74,6.708 2.5,0.396 10 false Accelerator Pedal Position (Angle) 5.344,1.021 5.875,1.323 0.531,0.302 10 false VPA1 5.354,1.375 5.792,1.688 0.438,0.313 10 false EP1 5.344,1.729 5.865,1.969 0.521,0.24 10 false VCP1 5.344,2 5.896,2.333 0.552,0.333 10 false VPA2 5.344,2.365 5.844,2.688 0.5,0.323 10 false EP2 5.344,2.719 5.885,3.063 0.542,0.344 10 false VCP2 1.948,0.521 2.573,0.875 0.625,0.354 10 false Hall IC 3.583,5.448 4.229,5.802 0.646,0.354 10 false VPA1 2.677,4.917 3.24,5.25 0.563,0.333 10 false VPA2 6.302,1.844 6.781,2.271 0.479,0.427 10 false ECM 0.156,3.188 1.594,3.583 1.438,0.396 10 false Accelerator Pedal Arm 0.333,2.792 1.354,3.083 1.021,0.292 10 false Magnetic Yoke 3.604,2.854 4.594,3.24 0.99,0.385 10 false Magnetic Yoke



h.

Camshaft Timing Oil Control Valve Assembly

i.

This camshaft timing oil control valve assembly controls the spool valve using duty cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advanced or retarded side. When the engine is stopped, the camshaft timing oil control valve assembly is in the most retarded position.

W102482E03
2.646,1.344 2.479,0.938 2.479,0.938 2.24,0.938 true 2.229,1.281 1.896,1.281 true 2.323,1.521 2.135,1.771 2.135,1.771 1.948,1.771 true 4.417,1.448 4.833,1.979 4.833,1.979 5.01,1.979 true 4.354,1.729 4.813,2.292 4.813,2.292 4.99,2.292 true 2.063,0.833 2.24,1.052 0.177,0.219 10 false *1 1.719,1.177 1.896,1.385 0.177,0.208 10 false *2 1.771,1.667 1.948,1.896 0.177,0.229 10 false *3 2.635,1.969 2.854,2.198 0.219,0.229 10 false *c 2.958,1.969 3.167,2.177 0.208,0.208 10 false *d 3.302,1.969 3.51,2.167 0.208,0.198 10 false *c 5.042,1.875 5.281,2.073 0.24,0.198 10 false *4 5.021,2.188 5.219,2.396 0.198,0.208 10 false *5 2.573,0.542 3.063,0.792 0.49,0.25 10 false *a (*e) 3.104,0.542 3.583,0.771 0.479,0.229 10 false *b (*e)

Text in Illustration
*1 Spool Valve *2 Sleeve
*3 Spring *4 Plunger
*5 Coil - -
*a To VVT-i Controller (Advance Side) *b To VVT-i Controller (Retard Side)
*c Drain *d Oil Pressure
*e On the camshaft timing oil control valve assembly (exhaust), the advance and retard sides are reversed. - -



i.

Throttle Control Motor

i.

A DC motor with excellent response and minimal power consumption is used for the throttle control motor. The ECM performs the duty cycle control of the direction and the amperage of the current that flows to the throttle control motor in order to regulate the opening of the throttle valve.

W102381E05
3.198,0.75 2.938,0.271 2.938,0.271 2.813,0.271 true 4.594,1.052 4.771,0.708 4.771,0.708 4.885,0.708 true 3.948,2.188 3.844,2.427 3.844,2.427 3.688,2.427 true 3.51,2.313 3.698,2.542 0.188,0.229 10 false *3 2.635,0.156 2.813,0.354 0.177,0.198 10 false *1 4.917,0.583 5.146,0.833 0.229,0.25 10 false *2

Text in Illustration
*1 Throttle Valve *2 Throttle Position Sensor Portion
*3 Throttle Control Motor - -



j.

Ignition Coil Assembly

i.

The Direct Ignition System (DIS) provides 6 ignition coil assemblies, one for each cylinder. The spark plug caps, which provide contact to spark plugs, are integrated with the ignition coil. Also, an igniter is enclosed to simplify the system.

W102322E05
3.552,1.74 3.104,1.448 3.104,1.448 2.979,1.448 true 3.479,3.156 3.021,2.865 3.021,2.865 2.906,2.865 true 3.74,2.063 4.135,1.802 4.135,1.802 4.24,1.802 true 3.698,1.74 4.146,1.448 4.146,1.448 4.26,1.448 true 3.698,0.813 3.823,0.427 3.823,0.427 4.021,0.427 true 2.802,1.344 3,1.615 0.198,0.271 10 false *2 4.271,1.698 4.521,1.969 0.25,0.271 10 false *5 2.729,2.76 2.938,3.031 0.208,0.271 10 false *3 3.5,3.365 3.729,3.625 0.229,0.26 10 false *a 4.302,1.344 4.531,1.615 0.229,0.271 10 false *4 4.052,0.323 4.25,0.563 0.198,0.24 10 false *1

Text in Illustration
*1 Igniter *2 Iron Core
*3 Plug Cap *4 Secondary Coil
*5 Primary Coil - -
*a Ignition Coil Cross Section - -



k.

Spark Plug

i.

Long-reach type spark plugs are used. This type of spark plug allows the area of the cylinder head that receives the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.


ii.

Iridium-tipped spark plugs are used to achieve a 192000 km (120000 miles) maintenance interval. By making the center electrode of iridium, it is possible to achieve superior ignition performance and durability when compared to platinum-tipped spark plugs.

W102488E02
3.073,1.313 2.906,0.354 2.906,0.354 2.677,0.354 true 3.885,1.365 4.052,0.417 4.052,0.417 4.281,0.417 true 1.854,3.406 2.167,3.5 2.167,3.5 2.323,3.5 true 1.865,3.542 2.177,3.813 2.177,3.813 2.333,3.813 true 4.677,3.094 4.469,2.771 4.469,2.771 4.344,2.771 true 5.896,3.094 6.104,2.771 6.104,2.771 6.229,2.771 true 4.313,0.281 4.552,0.531 0.24,0.25 10 false *1 2.51,0.24 2.698,0.448 0.188,0.208 10 false *1 2.354,3.385 2.563,3.594 0.208,0.208 10 false *2 2.354,3.698 2.552,3.948 0.198,0.25 10 false *3 4.177,2.646 4.365,2.865 0.188,0.219 10 false *4 6.26,2.646 6.448,2.906 0.188,0.26 10 false *5

Text in Illustration
*1 Water Jacket *2 Iridium Tip
*3 Platinum Tip *4 Long-reach Type Spark Plug
*5 Conventional Type Spark Plug - -




OPERATION


a.

Dual VVT-i System

i.

Using the engine speed, intake air mass, throttle position and engine coolant temperature, the ECM can calculate optimal valve timing for each driving condition and controls the camshaft timing oil control valve. In addition, the ECM uses signals from the camshaft position sensor and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W132970E01
0.479,0.792 2.125,1 1.646,0.208 10 false Mass Air Flow Meter 0.417,1.24 2.063,1.448 1.646,0.208 10 false Throttle Position Sensor 0.323,2.042 2.031,2.25 1.708,0.208 10 false Crankshaft Position Sensor 0.469,2.823 2.115,3.031 1.646,0.208 10 false Vehicle Speed Signal 4.24,0.771 5.885,0.979 1.646,0.208 10 false Duty Cycle Control 2.563,3.219 3.458,3.438 0.896,0.219 10 false Correction 2.865,3.688 3.573,3.906 0.708,0.219 10 false Feedback 2.708,7.146 3.604,7.365 0.896,0.219 10 false ECM 4.198,2.51 5.844,2.719 1.646,0.208 10 false Duty Cycle Control 4.146,4.24 5.792,4.448 1.646,0.208 10 false Duty Cycle Control 4.042,5.76 5.688,5.969 1.646,0.208 10 false Duty Cycle Control 0.51,3.26 2.021,3.698 1.51,0.438 10 false Engine Coolant Temperature Sensor 0.49,4.052 2,4.49 1.51,0.438 10 false Camshaft Position Sensor (Intake RH) 0.469,4.854 1.979,5.292 1.51,0.438 10 false Camshaft Position Sensor (Intake LH) 0.427,5.625 1.938,6.063 1.51,0.438 10 false Camshaft Position Sensor (Exhaust RH) 0.417,6.427 1.927,6.865 1.51,0.438 10 false Camshaft Position Sensor (Exhaust LH) 2.5,5.292 3.333,5.771 0.833,0.479 10 false Actual Valve Timing 2.469,1.448 3.302,1.927 0.833,0.479 10 false Target Valve Timing 4.802,1.188 6.615,1.625 1.813,0.438 10 false Camshaft Timing Oil Control Valve Assembly (Intake RH) 4.698,2.938 6.51,3.375 1.813,0.438 10 false Camshaft Timing Oil Control Valve Assembly (Intake LH) 4.719,4.677 6.583,5.104 1.865,0.427 10 false Camshaft Timing Oil Control Valve Assembly (Exhaust RH) 4.719,6.104 6.573,6.542 1.854,0.438 10 false Camshaft Timing Oil Control Valve Assembly (Exhaust LH)


ii.

When the camshaft timing oil control valve is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction:

W102383E04
0.5,0.438 6.906,3.333 6.406,2.896 0.5,3.719 6.906,6.615 6.406,2.896 0.938,1.802 0.656,1.01 0.656,1.01 0.958,1.01 true 1.198,2.417 1.198,2.969 1.198,2.969 1.427,2.969 true 1.5,4.667 1.5,4.042 1.5,4.042 1.646,4.042 true 1.323,5.688 1.323,6.177 1.323,6.177 1.521,6.177 true 5.917,6.271 5.615,6.448 5.615,6.448 5.458,6.448 true 6.177,6.146 6.396,6.01 6.396,6.01 6.563,6.01 true 5.208,2.823 5.042,2.969 5.042,2.969 4.896,2.969 true 5.448,2.729 5.667,2.896 5.667,2.896 5.833,2.896 true 1,0.948 1.188,1.229 0.188,0.281 10 false *1 1.677,3.969 1.865,4.25 0.188,0.281 10 false *1 1.469,2.896 1.656,3.177 0.188,0.281 10 false *2 1.542,6.125 1.729,6.406 0.188,0.281 10 false *2 6.313,1.479 6.542,1.719 0.229,0.24 10 false *3 3.917,5.323 4.146,5.563 0.229,0.24 10 false *3 5.292,6.385 5.49,6.604 0.198,0.219 10 false *4 6.594,5.948 6.792,6.167 0.198,0.219 10 false *5 4.75,2.906 4.979,3.146 0.229,0.24 10 false *4 5.865,2.823 6.094,3.063 0.229,0.24 10 false *5 0.594,0.521 0.844,0.771 0.25,0.25 10 false *a 0.594,3.802 0.844,4.052 0.25,0.25 10 false *b

Text in Illustration
*1 Vane *2 Rotation Direction
*3 ECM *4 In (Oil Pressure)
*5 Drain (Oil Pressure) - -
*a Advance Side Operation Intake Side *b Advance Side Operation Exhaust Side


iii.

When the camshaft timing oil control valve is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction:

W102384E02
0.333,0.385 6.74,3.281 6.406,2.896 0.333,3.625 6.74,6.521 6.406,2.896 1.219,1.563 1.01,1 1.01,1 1.229,1 true 1,2.198 1,2.76 1,2.76 1.219,2.76 true 1.198,4.74 1.198,4.115 1.198,4.115 1.344,4.115 true 1.333,5.729 1.333,6.219 1.333,6.219 1.531,6.219 true 5.542,6.073 5.24,6.25 5.24,6.25 5.083,6.25 true 5.802,6.25 6.021,6.104 6.021,6.104 6.188,6.104 true 4.99,2.583 4.823,2.729 4.823,2.729 4.688,2.729 true 5.208,2.729 5.427,2.896 5.427,2.896 5.594,2.896 true 1.26,0.885 1.49,1.125 0.229,0.24 10 false *1 1.375,4 1.594,4.25 0.219,0.25 10 false *1 1.24,2.635 1.469,2.896 0.229,0.26 10 false *2 1.563,6.115 1.823,6.385 0.26,0.271 10 false *2 6.302,1.333 6.5,1.542 0.198,0.208 10 false *3 3.76,5.25 3.958,5.469 0.198,0.219 10 false *3 4.906,6.125 5.094,6.385 0.188,0.26 10 false *4 6.219,5.979 6.448,6.219 0.229,0.24 10 false *5 4.521,2.615 4.698,2.844 0.177,0.229 10 false *4 5.625,2.781 5.844,2.99 0.219,0.208 10 false *5 0.417,0.438 0.729,0.76 0.313,0.323 10 false *a 0.427,3.708 0.729,4.021 0.302,0.313 10 false *b

Text in Illustration
*1 Rotation Direction *2 Vane
*3 ECM *4 Drain (Oil Pressure)
*5 In (Oil Pressure) - -
*a Retard Side Operation Intake Side *b Retard Side Operation Exhaust Side


iv.

After reaching the target timing, the engine valve timing is maintained by keeping the camshaft timing oil control valve in the neutral position unless the engine operating conditions change. This maintains the engine valve timing at the desired target position by preventing the engine oil from running out of the oil control valve.



b.

Fuel Pump Control

i.

In this vehicle, there are 2 types of fuel pump controls. The fuel pump is controlled to an optimum speed to match the engine operating conditions, and the fuel pump operation is stopped when the SRS airbags deploy.


ii.

The ECM transmits a fuel pump operation request signal to the fuel pump control ECU that corresponds to the engine operating conditions. The fuel pump control ECU receives this request signal and controls the speed of the fuel pump in 3 stages. As a result, under light engine loads, fuel pump speed is kept low to reduce electric power loss.


iii.

A fuel cut control is used to stop the fuel pump when any of the SRS airbags deploys. In this control, if an airbag deployment signal from the center airbag sensor assembly is detected by the ECM, the ECM will turn off the circuit opening relay. As a result, the power supply to the fuel pump control ECU is stopped, causing the fuel pump to stop operating. After the fuel cut control has been activated, turning the ignition switch from off to ON cancels the fuel cut control, and the engine can be restarted.

W102385E07
3.26,3.396 3.469,2.094 true 0.323,1.427 1.677,2.125 1.354,0.698 10 false Front Airbag Sensors (RH and LH) 0.281,0.417 1.708,1.229 1.427,0.813 10 false Rear Floor Side Airbag Sensors (RH and LH) 0.313,2.427 1.583,3.156 1.271,0.729 10 false Rear Airbag Sensors (RH and LH) 0.323,3.667 1.646,4.333 1.323,0.667 10 false Side Airbag Sensors (RH and LH) 2.292,1.188 2.948,2.521 0.656,1.333 10 false Center Airbag Sensor Assembly 4.615,1.958 5.333,2.927 0.719,0.969 10 false Fuel Pump Operation Request 4.646,3.063 5.302,3.729 0.656,0.667 10 false Diagnosis Signal 5.469,2.115 6.156,2.927 0.688,0.813 10 false Fuel Pump Control ECU 6.604,2.073 7.021,2.719 0.417,0.646 10 false Fuel Pump 4.802,0.677 5.49,1.01 0.688,0.333 10 false IG2 Relay 6.125,0.698 6.74,1.344 0.615,0.646 10 false EFI Main Relay 2.667,3.385 4.438,3.958 1.771,0.573 10 false CAN communication line 4.021,1.938 4.417,2.26 0.396,0.323 10 false ECM


iv.

The fuel pump control ECU controls fuel pump speed by receiving a duty cycle signal (FPC terminal input) from the ECM, and control is performed in 3 stages.


v.

The fuel pump control ECU also detects failures in the input and output circuits at the fuel pump ECU and transmits the failure status to the ECM.

W102386E04
3.063,1.24 3.781,2.406 0.719,1.167 10 false Fuel Pump Operation Request 2.771,2.458 3.896,2.938 1.125,0.479 10 false Diagnosis Signal 3.938,1.271 4.615,2.542 0.677,1.271 10 false Fuel Pump Control ECU 5.073,1.323 5.583,2.292 0.51,0.969 10 false Fuel Pump 2.063,1.76 2.479,2.198 0.417,0.438 10 false ECM 2.604,0.875 3.823,1.198 1.219,0.323 10 false Duty Cycle Signal 2.552,1.24 2.917,1.635 0.365,0.396 10 false FPC 2.542,2.479 2.781,2.844 0.24,0.365 10 false DI

FPC Terminal Input
FPC Input Signal (Duty Cycle Signal) Fuel Pump Speed
W132971E01
0.677,1.104 0.99,1.302 0.313,0.198 10 false +B 0.573,1.427 0.885,1.625 0.313,0.198 10 false GND

High
W132972E01
1.26,0.573 1.854,0.781 0.594,0.208 10 false 12.3 ms 1.167,0.833 1.656,1.042 0.49,0.208 10 false 8.2 ms 0.531,1.125 0.854,1.333 0.323,0.208 10 false +B 0.427,1.417 0.75,1.625 0.323,0.208 10 false GND

Middle
W132973E01
1.208,0.615 1.76,0.813 0.552,0.198 10 false 12.3 ms 1.167,0.875 1.719,1.083 0.552,0.208 10 false 4.1 ms 0.604,1.135 0.917,1.333 0.313,0.198 10 false +B 0.49,1.469 0.802,1.667 0.313,0.198 10 false GND

Low
W132974E01
0.583,1.042 0.896,1.24 0.313,0.198 10 false +B 0.479,1.417 0.792,1.615 0.313,0.198 10 false GND

Stop



c.

ETCS-i

i.

The ECM drives the throttle control motor by determining the target throttle valve opening in accordance with the respective operating condition.


ii.

The ECM controls the throttle to an optimal throttle valve opening that is appropriate for the driving conditions such as the amount of accelerator pedal effort and the engine speed in order to achieve excellent throttle control and comfort in all operating ranges.

W100289E42
1.969,1.688 2.115,2 0.146,0.313 10 false 0 1.969,2.979 2.115,3.292 0.146,0.313 10 false 0 1.969,4.083 2.115,4.396 0.146,0.313 10 false 0 0.042,0.083 3.854,0.49 3.813,0.406 10 false - Control Examples during Acceleration and Deceleration - 5.479,0.354 6.771,0.729 1.292,0.375 10 false : With control 5.479,0.729 6.771,1.104 1.292,0.375 10 false : Without control 0.635,2.51 1.677,3.229 1.042,0.719 10 false Throttle Valve Opening Angle 0.635,1.271 1.677,1.99 1.042,0.719 10 false Vehicle's Longitudinal G 0.635,3.635 1.813,4.583 1.177,0.948 10 false Accelerator Pedal Depressed Angle 5.094,4.229 5.458,4.615 0.365,0.385 10 false Time


iii.

The ECM controls the throttle valve in order to constantly maintain an ideal idle speed.


iv.

As part of the TRC, the throttle valve opening angle is reduced by a demand signal sent from the skid control ECU to the ECM. This demand signal is sent if an excessive amount of slippage occurs at a drive wheel, thus ensuring vehicle stability and applying an appropriate amount of power to the road.


v.

In order to bring the effectiveness of the VSC into full play, the throttle valve angle is regulated through a coordination control by the skid control ECU and the ECM.


vi.

On the models with cruise control system, the ECM directly actuates the throttle valve for operation of the cruise control.


vii.

On the models with dynamic radar cruise control system, the dynamic radar cruise control uses a millimeter wave radar sensor and driving support ECU to determine the distance, direction, and relative speed of a vehicle ahead. Thus, the system can effect deceleration control, follow-up control, constant speed control, and acceleration control. To make these controls possible, the ECM controls the throttle valve.



d.

Starter Control

i.

When the driver pushes the engine switch once and the power management control ECU detects a start signal, the power management control ECU will output ACCD and STAR signals and begin cranking. Also, the driver can continue cranking for up to 30 seconds by pushing and holding the engine switch.


ii.

If the engine speed reaches approximately 500 rpm, the ECM will judge that the engine has started and will send a signal to the power management control ECU using CAN communication. The power management control ECU will then stop the operation of the starter.


iii.

If CAN communication is cut between the power management control ECU and the ECM, the power management control ECU will receive an engine speed signal (NE) directly from the ECM and will stop the operation of the starter.


iv.

This system will cut off the power current which activates the accessories while the engine is being cranked. This prevents the intermittent blinking of the accessory lights caused by the voltage instability that occurs during engine cranking.


v.

This system has the following protections:

·

The starter will not operate if the engine is operating normally.

·

If the engine switch is pushed and held, cranking will stop once the engine speed reaches a pre-determined level. This prevents the starter from over-revving.

·

If the engine does not start even after approximately 6 seconds of starter operation, the power management control ECU will cancel the starter relay output. Furthermore, if the engine does not start after the engine switch has been pushed and held and cranking has continued for 30 seconds, cranking will be canceled in order to protect the starter.

·

It will not be possible to operate the starter for 2 seconds after engine starting has failed and cranking has been canceled. This helps to protect the starter.


W100462E34
0.625,1.521 1.573,1.833 0.948,0.313 10 false Engine Switch 3.323,1.542 3.719,1.906 0.396,0.365 10 false ECM 4.042,1.281 5.365,1.865 1.323,0.583 10 false CAN (Power Management Bus*1), V1 Bus *2 1.979,2.219 2.74,2.552 0.76,0.333 10 false ACC Relay 4.5,4.979 5.448,5.438 0.948,0.458 10 false Starter Relay 1.594,5.156 2.719,5.542 1.125,0.385 10 false Starter 5.656,0.708 6.052,1.073 0.396,0.365 10 false SSW 5.646,1.229 6.875,1.958 1.229,0.729 10 false Power Management Control ECU 5.656,1.99 6.052,2.354 0.396,0.365 10 false NE 5.656,2.51 6.281,2.74 0.625,0.229 10 false ACCD 5.656,2.781 6.281,3.146 0.625,0.365 10 false STAR 5.656,4.885 5.979,5.219 0.323,0.333 10 false STA 5.625,5.51 5.948,5.844 0.323,0.333 10 false STP 4.688,6.167 6.083,6.542 1.396,0.375 10 false Stop Light Signal*2 4.521,2.906 5.479,4.646 0.958,1.74 10 false Clutch Start Switch*1 or Park/Neutral Position Switch Assembly*2 0.427,6.385 2.948,6.719 2.521,0.333 10 false *2: Models with automatic transmission 0.427,6.052 2.865,6.375 2.438,0.323 10 false *1: Models with manual transmission

W102484E02
1.948,0.25 2.229,0.521 0.281,0.271 10 On 1.948,1.198 2.24,1.469 0.292,0.271 10 On 1.948,2.0 2.26,2.271 0.313,0.271 10 On 1.948,1.604 2.24,1.875 0.292,0.271 10 Off 1.958,0.677 2.24,0.948 0.281,0.271 10 Off 1.938,2.396 2.25,2.667 0.313,0.271 10 Off 0.479,0.427 1.385,0.813 0.906,0.385 10 Starter Signal 0.479,2.146 1.625,2.635 1.146,0.49 10 Accessory Power 0.49,1.396 1.396,1.781 0.906,0.385 10 Starter Relay 0.323,3.073 1.979,3.448 1.656,0.375 10 Engine Speed Signal (NE) 1.688,3.938 5.292,4.604 3.604,0.667 10 ECM determines that the engine has started successfully when the engine speed is approximately 500 rpm. 5.573,2.521 6.844,3.188 1.271,0.667 10 Successful Starting of Engine 5.594,3.229 6.573,3.896 0.979,0.667 10 Failed Starting of Engine