Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
NM27T0E _51 Engine / Hybrid System _053577 2TR-FE ENGINE MECHANICAL _0260102 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Cylinder Head Cover Sub-assembly

i.

The cylinder head cover sub-assembly is made of plastic to reduce weight and noise.


ii.

Acrylic rubber, which excels in heat resistance and reliability, is used for the cylinder head cover gasket. Also, the plug of the cylinder head cover gasket has been integrated in consideration of serviceability.


iii.

Baffle plate made of plastic is provided inside the cylinder head cover sub-assembly to reduce the consumption of engine oil through blow-by gas. The baffle plate is welded onto the cylinder head cover sub-assembly, and cannot be removed. An oil delivery pipe is installed inside the cylinder head cover sub-assembly. This ensures lubrication to the sliding parts of the valve rocker arms, thus improving reliability.

W127695E02
2.156,1.26 1.406,0.917 true 2.583,2.5 1.781,2.333 true 2.771,3.323 1.844,3.479 true 5.823,1.365 4.719,1.635 true 5.99,3.969 5.125,3.74 true 1.24,0.781 1.427,1 0.188,0.219 10 false *1 1.594,2.208 1.792,2.458 0.198,0.25 10 false *2 5.854,1.24 6.073,1.51 0.219,0.271 10 false *5 1.667,3.365 1.865,3.625 0.198,0.26 10 false *3 6.031,3.885 6.26,4.146 0.229,0.26 10 false *4

Text in Illustration
*1 Cylinder Head Cove Sub-assembly *2 Ventilation Baffle Plate
*3 Oil Delivery Pipe *4 Cylinder Head Cover Gasket
*5 PCV Connector (No.1 Ventilation Connector) - -



b.

Cylinder Head Gasket

i.

A steel-laminate type cylinder head gasket is used.


ii.

A shim has been added around the cylinder bore to increase the sealing surface, thus improving sealing performance and durability.

W126175E02
1.708,0.229 2.135,0.344 true 2.479,2.146 2.854,2.177 true 1.552,0.104 1.75,0.323 0.198,0.219 10 false *1 2.302,2.031 2.521,2.25 0.219,0.219 10 false *2 3.646,2.375 3.896,2.635 0.25,0.26 10 false *a

Text in Illustration
*1 Cylinder Head Gasket *2 Shim
*a A - A Cross Section - -



c.

Cylinder Head Sub-assembly

i.

The cylinder head sub-assembly, which is made of aluminum alloy, contains a pentroof type combustion chamber. The spark plug has been located in the center of the combustion chamber in order to improve the engine's anti-knocking performance.


ii.

The angle between the intake and exhaust valves is narrowed and set at 22.85° to permit a compact cylinder head.


iii.

A cross-flow intake and exhaust layout is used to improve intake and exhaust efficiency.


iv.

A taper squish combustion chamber is used to improve anti-knocking performance and intake efficiency. In addition, engine performance and fuel economy have been improved.


v.

Long nozzle type fuel injector assemblies are installed in the cylinder head to reduce the distance from the fuel injector to the intake valve, thus preventing the fuel from adhering to the intake port walls, and reducing exhaust emissions.


vi.

The routing of the water jacket in the cylinder head is optimized to achieve higher cooling performance.


vii.

An air injection port, which directs the air from the air pump assembly to the exhaust port of each cylinder, has been provided on top of the exhaust port.

U170783E03
0.208,1.417 0.563,1.594 true 0.344,4.125 0.708,3.906 true 4.177,6.323 4.438,6.438 true 1.667,1.281 1.448,1.083 1.448,1.083 1.135,1.5 true 2.792,0.948 2.615,0.708 2.615,0.708 2.281,1.156 true 2.854,1.594 3.375,1.708 3.375,1.708 3.375,1.458 true 1.708,1.938 2.177,2.01 2.177,2.01 2.198,1.771 true 6.792,5.698 6.604,5.833 true 5.344,5.438 5.292,5.75 true 1.542,7.042 1.75,7.24 1.75,7.24 1.99,7.021 true 4.26,0.635 4.417,0.813 0.156,0.177 10 false *h 0.063,1.292 0.313,1.542 0.25,0.25 10 false *1 2.51,0.51 2.76,0.76 0.25,0.25 10 false *1 1.333,0.885 1.583,1.135 0.25,0.25 10 false *1 2.156,2.052 2.406,2.302 0.25,0.25 10 false *1 3.354,1.74 3.604,1.99 0.25,0.25 10 false *1 0.208,4.083 0.469,4.333 0.26,0.25 10 false *2 0.167,4.958 0.427,5.208 0.26,0.25 10 false *a 0.625,6.448 0.823,6.698 0.198,0.25 10 false *c 1.656,7.229 1.917,7.479 0.26,0.25 10 false *d 3,6.292 3.26,6.542 0.26,0.25 10 false *e 6.646,6.188 6.906,6.438 0.26,0.25 10 false *e 4.188,6.521 4.385,6.771 0.198,0.25 10 false *c 6.833,5.563 7.094,5.813 0.26,0.25 10 false *3 5.281,5.229 5.542,5.479 0.26,0.25 10 false *g 1.594,4.948 2.115,5.208 0.521,0.26 10 false 22.85° 3.74,4.958 4.01,5.208 0.271,0.25 10 false *b 4.031,6.146 4.281,6.396 0.25,0.25 10 false *f

Text in Illustration
*1 Camshaft Bearing Cap *2 Cylinder Head Sub-Assembly
*3 Fuel Injector Assembly - -
*a A - A Cross Section *b B - B Cross Section
*c Exhaust Side *d Taper Squish
*e Intake Side *f Air Injection Port
*g Spark Plug Hole *h Top View
V100144

Water Jacket - -



d.

Cylinder Block Sub-assembly

i.

The cylinder block sub-aseembly is made of cast iron, and the rib shape of each part has been optimized to increase rigidity while reducing vibration and noise.


ii.

A water passage is provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction keeps the temperature of the cylinder walls uniform.

W102307E05
5.729,2.365 6.042,2.563 0.313,0.198 10 true *1

Text in Illustration
*1 Water Passage - -



e.

Balance Shaft

i.

For in-line 4-cylinder engines, the main cause of vibration is imbalanced inertial force of reciprocating parts such as the pistons and connecting rods. The engine vibration has been reduced by using 2 balance shafts to cancel the imbalanced inertial force, thereby reducing engine noise (booming noise).


ii.

The 2 balance shafts are built into the cylinder block sub-assembly. Using a chain, sprockets and gears, both balance shafts rotate at twice the speed of the crankshaft with each balance shaft rotating in the opposite direction of the other.


iii.

The chain tensioner uses a spring and oil pressure to maintain proper chain tension at all times. A ratchet type non-return mechanism is also included.


iv.

The chain tensioner has 2 oil holes that spray engine oil for lubricating the balance shaft chain. Furthermore, they lubricate the timing chain that drives the camshaft.

W102308E02
2.25,1.021 2.448,0.542 2.448,0.542 2.635,0.542 true 1.542,1.365 1.542,0.406 1.542,0.406 1.75,0.406 true 1.375,0.792 1.271,0.354 1.271,0.354 1.146,0.354 true 1.219,0.885 0.927,0.583 0.927,0.583 0.771,0.583 true 1.083,1.083 0.844,0.948 0.844,0.948 0.677,0.948 true 1.375,1.365 1.052,1.271 1.052,1.271 0.948,1.271 true 1.604,1.438 1.604,1.76 1.604,1.76 0.917,1.76 false 1.333,1.427 1.333,1.76 false 1.073,2.688 0.781,2.344 0.781,2.344 0.635,2.344 true 1,3.281 0.594,3.49 0.594,3.49 0.438,3.49 true 1.677,4.042 1.531,4.344 1.531,4.344 1.396,4.344 true 2.115,3.115 2.76,2.292 2.76,2.292 2.948,2.292 true 2.458,3.052 2.906,2.729 2.906,2.729 3.031,2.729 true 2.479,3.292 2.969,3.292 true 6.115,2.365 6.115,0.823 6.115,0.823 5.219,0.823 true 5.458,2.167 5.458,0.823 true 2.656,0.417 2.875,0.74 0.219,0.323 10 false *1 0.969,0.25 1.177,0.49 0.208,0.24 10 false *2 0.594,0.469 0.781,0.719 0.188,0.25 10 false *3 0.5,0.844 0.698,1.094 0.198,0.25 10 false *4 0.781,1.167 0.969,1.375 0.188,0.208 10 false *5 1.781,0.281 2.01,0.573 0.229,0.292 10 false *5 0.74,1.635 0.927,1.885 0.188,0.25 10 false *a 0.458,2.24 0.667,2.5 0.208,0.26 10 false *6 0.271,3.375 0.469,3.646 0.198,0.271 10 false *7 1.219,4.24 1.417,4.469 0.198,0.229 10 false *8 2.99,2.177 3.229,2.438 0.24,0.26 10 false *9 3.073,2.635 3.448,2.875 0.375,0.24 10 false *10 3,3.177 3.302,3.438 0.302,0.26 10 false *11 4.958,0.708 5.229,0.969 0.271,0.26 10 false *12

Text in Illustration
*1 Spring *2 Cam Spring
*3 Cam *4 Plunger
*5 Oil Hole *6 Balance Shaft Drive Gear
*7 Balance Shaft Driven Gear *8 Crankshaft Timing Sprocket
*9 Chain Tensioner *10 Balance Shaft Timing Sprocket
*11 Balance Shaft Chain *12 Balance Shaft
*a Engine Oil - -



f.

Piston

i.

The pistons are made of aluminum alloy.


ii.

The tops of the pistons use a taper squish shape to achieve fuel combustion efficiency.


iii.

The piston skirt is coated with resin to reduce friction losses.


iv.

The groove of the top ring has been coated with anodic oxide to improve wear resistance and rust resistance.

W126178E02
3.146,0.865 3.802,0.271 3.802,0.271 4.5,0.833 false 3.719,0.073 3.927,0.281 0.208,0.208 10 false *a 6.688,1.5 6.917,1.729 0.229,0.229 10 false *3 6.677,1.073 6.906,1.302 0.229,0.229 10 false *2 6.667,0.698 6.896,0.927 0.229,0.229 10 false *1

Text in Illustration
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Oil Ring - -
*a Taper Squish Shape - -
V100144

Resin Coating
V100145

Anodic Oxide Coating



g.

Connecting Rod and Connecting Rod Bearing

i.

Connecting rods that have been forged for high strength are used for weight reduction.


ii.

Knock pins are used at the mating surfaces of the bearing caps of the connecting rod to minimize the shifting of the bearing caps during assembly.


iii.

Plastic region tightening bolts are used.


iv.

An aluminum bearing is used for the connecting rod bearings.


v.

The lining surface of the connecting rod bearing has been micro-grooved to achieve an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibrations have been reduced.

W102310E02
1.792,3.021 1.792,3.469 1.792,3.469 3.042,3.469 true 2.625,2.615 2.823,2.302 2.823,2.302 2.958,2.302 true 4.417,2.115 4.25,1.792 4.25,1.792 4.083,1.792 true 5.813,1.167 5.927,0.688 5.927,0.688 6.125,0.688 true 2.635,3.021 2.635,3.469 true 3.083,3.333 3.302,3.552 0.219,0.219 10 false *1 2.99,2.177 3.219,2.427 0.229,0.25 10 false *2 3.896,1.677 4.083,1.896 0.188,0.219 10 false *3 6.156,0.542 6.385,0.792 0.229,0.25 10 false *4

Text in Illustration
*1 Plastic Region Tightening Bolt *2 Knock Pin
*3 Connecting Rod Bearing *4 Micro-grooved Surface



h.

Crankshaft and Crankshaft Bearing

i.

The crankshaft has 5 journals and 8 balance weights.


ii.

All pin and journal fillets are roll-finished to maintain adequate strength.


iii.

The crankshaft bearing is made of aluminum alloy.


iv.

The crankshaft bearing caps are tightened using 2 plastic region tightening bolts for each journal.


v.

Similar to the connecting rod bearings, the lining surface of the crankshaft bearings has been micro-grooved to achieve an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibrations have been reduced.


vi.

The upper main bearing has an oil groove around its inside circumference.

U149556E02
1.635,2.49 1.406,2.146 1.406,2.146 1.24,2.146 true 6.198,1.354 6.427,0.948 6.427,0.948 6.573,0.948 true 5.448,1.531 5.302,1.156 5.302,1.156 5.177,1.156 true 5.281,1.677 5.094,1.51 5.094,1.51 4.969,1.51 true 5.302,2.094 5.083,2.281 5.083,2.281 4.927,2.281 true 6.208,2.792 6.438,3.198 6.438,3.198 6.583,3.198 true 1.063,2.021 1.25,2.26 0.188,0.24 10 false *1 1.458,0.5 1.667,0.729 0.208,0.229 10 false *a 6.615,0.833 6.844,1.115 0.229,0.281 10 false *2 5.01,1.042 5.198,1.271 0.188,0.229 10 false *3 4.792,1.396 4.99,1.635 0.198,0.24 10 false *4 4.75,2.167 4.948,2.406 0.198,0.24 10 false *4 6.615,3.094 6.865,3.354 0.25,0.26 10 false *5

Text in Illustration
*1 Oil Hole *2 Upper Main Bearing
*3 Oil Grooved *4 Micro-grooved
*5 Lower Main Bearing - -
*a Roll-finished - -



i.

Crankshaft Pulley

i.

The rigidity of the crankshaft pulley with its built-in torsional damper rubber reduces noise.

W102312E02
3.719,0.531 3.958,0.333 3.958,0.333 4.104,0.333 true 4.135,0.219 4.323,0.438 0.188,0.219 10 false *1

Text in Illustration
*1 Torsional Damper Rubber - -



j.

Oil Pan

i.

No. 1 oil pan is made of aluminum alloy.


ii.

No. 2 oil pan is made of steel.


iii.

No. 1 oil pan is secured to the cylinder block and the transmission in order to increase rigidity.

W102313E02
4.635,1.323 5,0.542 5,0.542 5.313,0.542 true 4.094,2.083 4.25,2.49 4.25,2.49 4.427,2.49 true 5.344,0.448 5.552,0.667 0.208,0.219 10 false *1 4.438,2.417 4.646,2.635 0.208,0.219 10 false *2

Text in Illustration
*1 No. 1 Oil Pan *2 No. 2 Oil Pan



k.

Valve Mechanism

i.

This engine uses valve rocker arm sub-assemblies with built-in needle bearings. This reduces the friction that occurs between the cams and the roller rocker arms when the valves are pushed down, thus improving fuel economy.


ii.

A valve lash adjuster assembly, which maintains a constant zero valve clearance through the use of oil pressure and spring force, is used.


iii.

The intake camshaft and exhaust camshaft driven by the crankshaft via the timing chain.


iv.

The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used to achieve low fuel consumption and higher engine performance to reduce exhaust emissions.

W127095E02
0.76,4.969 0.927,4.354 true 0.542,4.594 1.104,4.052 true 0.49,4.094 0.927,3.948 true 0.292,2.615 0.698,2.49 true 0.26,2.135 0.896,2.094 true 0.26,1.448 0.563,1.625 true 0.615,1.042 0.781,1.417 true 1.177,0.969 1.042,1.5 true 3.313,0.906 3.479,0.625 true 3.792,1.135 4.177,1.135 true 5.354,5.24 5.656,4.969 true 5.448,3.563 5.813,3.417 true 5.469,3.229 5.927,3.156 true 5.51,2.667 5.875,2.583 false 5.656,1.625 6.021,1.698 true 6.229,1.427 5.792,1.323 5.792,1.323 6.073,1.5 true 5.823,1.063 6.156,1.271 true 6.01,0.74 6.115,0.99 true 6.458,1.854 6.625,2.031 true 1.5,2.688 1.927,2.344 true 0.5,0.833 0.708,1.052 0.208,0.219 10 false *1 1.177,0.813 1.469,1.042 0.292,0.229 10 false *11 3.49,0.469 3.792,0.719 0.302,0.25 10 false *10 4.208,1 4.438,1.219 0.229,0.219 10 false *9 0.083,1.313 0.292,1.531 0.208,0.219 10 false *2 0.083,2.021 0.281,2.24 0.198,0.219 10 false *3 0.115,2.521 0.302,2.76 0.188,0.24 10 false *4 1.927,2.208 2.146,2.427 0.219,0.219 10 false *8 0.313,3.99 0.51,4.219 0.198,0.229 10 false *5 0.406,4.583 0.625,4.833 0.219,0.25 10 false *6 0.677,4.979 0.948,5.208 0.271,0.229 10 false *7 5.167,5.24 5.458,5.469 0.292,0.229 10 false *19 5.198,3.479 5.458,3.729 0.26,0.25 10 false *18 5.229,3.125 5.49,3.375 0.26,0.25 10 false *17 5.26,2.573 5.51,2.792 0.25,0.219 10 false *16 5.406,1.5 5.656,1.75 0.25,0.25 10 false *15 5.552,1.177 5.813,1.385 0.26,0.208 10 false *14 5.583,0.906 5.844,1.125 0.26,0.219 10 false *13 5.885,0.531 6.167,0.74 0.281,0.208 10 false *12 6.635,2.021 6.938,2.25 0.302,0.229 10 false *20

Text in Illustration
*1 Chain Sub-assembly *2 Exhaust VVT-i Controller (Camshaft Timing Exhaust Gear Assembly)
*3 Intake VVT-i Controller (Camshaft Timing Gear Assembly) *4 No. 1 Chain Tensioner Assembly
*5 Chain Tensioner Slipper *6 Crankshaft Timing Gear
*7 Crankshaft *8 No. 1 Chain Vibration Damper
*9 Intake Camshaft (Camshaft) *10 Exhaust Camshaft (No. 2 Camshaft)
*11 Timing Chain Guide *12 No. 1 Valve Rocker Arm Sub-assembly
*13 Valve Stem Cap *14 Valve Spring Retainer Lock
*15 Valve Spring Retainer *16 Inner Compression Spring
*17 Valve Stem Oil Seal *18 Valve Spring Seat
*19 Valve *20 Valve Lash Adjuster Assembly



l.

Valve Timing

W126141E05
2.375,0.406 2.667,0.406 2.667,0.406 2.948,0.813 true 2.042,3.26 2.208,3.26 2.208,3.26 2.49,2.729 true 4.521,3.167 4.24,3.167 4.24,3.167 3.823,2.781 true 4.552,0.646 4.229,0.646 4.229,0.646 3.885,1.083 true 3.229,0.125 3.625,0.417 0.396,0.292 10 false TDC 3.146,0.469 3.344,0.698 0.198,0.229 10 false 1° 3.521,0.469 3.75,0.677 0.229,0.208 10 false 8° 2.521,0.76 2.823,1.052 0.302,0.292 10 false 28° 4.24,0.885 4.563,1.177 0.323,0.292 10 false 44° 4.604,0.552 6.75,1 2.146,0.448 10 false Exhaust VVT-i Operation Range 0.49,0.292 2.406,0.667 1.917,0.375 10 false Intake VVT-i Operation Range 1.917,2.188 2.188,2.458 0.271,0.271 10 false 72° 2.583,2.938 2.875,3.24 0.292,0.302 10 false 36° 4.354,2.615 4.646,2.906 0.292,0.292 10 false 53° 5.021,1.323 6.865,1.698 1.844,0.375 10 false : Intake valve opening angle 5.021,1.708 7.01,2.156 1.99,0.448 10 false : Exhaust valve opening angle 4.563,3.063 6.823,3.438 2.26,0.375 10 false Exhaust VVT-i Operation Range 0.177,3.146 2.073,3.5 1.896,0.354 10 false Intake VVT-i Operation Range 3.229,3.417 3.76,3.708 0.531,0.292 10 false BDC 3.51,3.135 3.75,3.354 0.24,0.219 10 false 8°


m.

Camshaft

i.

The camshafts are made of cast iron alloy.


ii.

In conjunction with the use of the Dual Variable Valve Timing-intelligent (Dual VVT-i) system, an oil passage is provided in the intake and exhaust camshafts in order to supply engine oil pressure to the Dual VVT-i system.


iii.

Each VVT-i controller has been installed on the front of the intake and exhaust camshafts to vary the timing of the intake and exhaust valves.


iv.

To detect the intake camshaft position, a timing rotor is provided in front of the intake VVT-i controller. To detect the exhaust camshaft position, a timing rotor is provided on the exhaust camshaft. These timing rotors are used by the Cam Position sensor to detect the actual position of the intake and exhaust camshafts.

W127696E02
1.156,0.563 1.521,0.771 true 1.135,1.896 1.635,1.833 true 2.354,3.417 2.521,3.094 true 1.594,3.052 2.052,2.833 true 5.01,1.104 5.365,0.677 true 5.729,1.771 6.292,1.552 true 1.198,1.063 0.792,1.167 0.792,1.167 1.042,1.208 true 0.927,1.406 1.26,1.24 true 4.385,2.76 4.75,2.979 true 4.375,3.385 4.146,3.385 4.146,3.385 4.51,3.208 true 5.323,3.521 5.073,3.25 true 3.24,1.49 3.323,1.063 true 1.021,0.375 1.219,0.563 0.198,0.188 10 false *a 3.25,0.865 3.448,1.073 0.198,0.208 10 false *c 0.771,1.333 1.01,1.552 0.24,0.219 10 false *a 0.969,1.781 1.146,1.99 0.177,0.208 10 false *1 1.427,2.958 1.604,3.188 0.177,0.229 10 false *c 2.25,3.406 2.5,3.646 0.25,0.24 10 false *2 5.26,3.5 5.469,3.708 0.208,0.208 10 false *a 3.979,3.292 4.156,3.5 0.177,0.208 10 false *b 4.219,2.604 4.406,2.823 0.188,0.219 10 false *a 6.313,1.427 6.573,1.677 0.26,0.25 10 false *3 5.365,0.51 5.594,0.75 0.229,0.24 10 false *4 0.604,1.052 0.802,1.281 0.198,0.229 10 false *b

Text in Illustration
*1 Exhaust VVT-i Controller (Camshaft Timing Gear Assembly) *2 Intake VVT-i Controller (Camshaft Timing Gear Assembly)
*3 Intake Camshaft (No. 1 Camshaft) *4 Exhaust Camshaft (No. 2 Camshaft)
*a Oil Passage (Advance) *b Oil Passage (Retard)
*c Timing Rotor - -



n.

VVT-i Controller

i.

Each VVT-i controller consists of the housing driven from the timing chain and the vane coupled with the intake or exhaust camshaft.


ii.

The oil pressure sent from the advanced or retarded side path at the intake and exhaust camshafts causes rotation in the VVT-i controller vane circumferential direction to vary the intake and exhaust valve timing continuously.


iii.

The intake side has a 3-blade vane and the exhaust side has a 4-blade vane.


iv.

When the engine is stopped, the intake camshaft will be in the most retarded state and the exhaust camshaft will be in the most advanced state to ensure startability.


v.

An advance assist spring is provided on the exhaust VVT-i controller. This spring applies torque in the advance direction when the engine is stopped, thus ensuring the engagement of the lock pin.


vi.

When hydraulic pressure is not applied to the VVT-i controller immediately after the engine has started, the lock pin locks the movement of the VVT-i controller to prevent a knocking noise. Thereafter, when hydraulic pressure is applied to the VVT-i controller, the lock pin is released.

W127697E04
1.313,0.573 1.635,0.771 true 1.5,1.677 1.719,1.438 true 2.51,1.823 2.833,1.823 true 2.875,2.906 3.063,2.625 true 3.417,0.25 3.354,0.698 true 5.344,1.5 5.469,1.115 true 2.958,1.979 3.24,1.458 true 1.927,1.052 2.208,0.417 true 3.552,2.427 3.875,2.385 true 2.406,1.281 2.729,1.24 true 1.167,0.448 1.344,0.688 0.177,0.24 10 false *1 2.365,1.76 2.542,2 0.177,0.24 10 false *1 3.208,1.302 3.385,1.542 0.177,0.24 10 false *4 3.896,2.313 4.073,2.552 0.177,0.24 10 false *3 5.875,3.323 6.052,3.563 0.177,0.24 10 false *e 4.896,3.333 5.073,3.573 0.177,0.24 10 false *d 3.813,2.688 3.99,2.927 0.177,0.24 10 false *c 5.396,0.948 5.573,1.188 0.177,0.24 10 false *6 3.323,0.083 3.5,0.323 0.177,0.24 10 false *5 2.74,1.167 2.917,1.406 0.177,0.24 10 false *3 1.385,1.667 1.813,1.969 0.427,0.302 10 false *2(*a) 2.646,2.948 3.073,3.25 0.427,0.302 10 false *2(*b) 2.125,0.24 2.302,0.479 0.177,0.24 10 false *4

Text in Illustration
*1 Outer Housing *2 Vane
*3 Timing Chain Sprocket *4 Lock Pin
*5 Exhaust Camshaft (No. 2 Camshaft) *6 Intake Camshaft (No. 1 Camshaft)
*a Fixed on Exhaust Camshaft *b Fixed on Intake Camshaft
*c Lock Pin Condition *d Engine Operating
*e Engine Stopped - -



o.

Timing Chain and Chain Tensioner

i.

A high-strength roller chain with a 9.525 mm (0.375 in.) pitch is used to make the engine more compact and to ensure the reliability of the timing chain.


ii.

The chain tensioner uses a spring and oil pressure to maintain proper chain tension at all times. The chain tensioner suppresses noise generated by the timing chain.


iii.

A ratchet type non-return mechanism is used in the chain tensioner.

W127098E02
2.479,0.896 2.063,0.833 true 3.385,0.708 2.792,0.458 true 3.875,0.604 4.156,0.281 true 4.177,1.167 4.833,1.49 true 4.271,1.844 4.708,2.104 true 3.802,3.198 3.594,3.542 true 3.781,3.052 3.302,3.167 true 3.635,2.854 3.25,2.708 true 3.354,0.177 3.646,0.49 true 4.75,2.021 4.948,2.229 0.198,0.208 10 false *7 1.896,0.708 2.073,0.917 0.177,0.208 10 false *3 2.615,0.323 2.802,0.552 0.188,0.229 10 false *2 4.167,0.125 4.365,0.354 0.198,0.229 10 false *9 4.875,1.427 5.125,1.656 0.25,0.229 10 false *8 3.458,3.531 3.677,3.74 0.219,0.208 10 false *6 3.083,2.583 3.281,2.802 0.198,0.219 10 false *4 3.125,3.073 3.333,3.281 0.208,0.208 10 false *5 3.208,0.021 3.427,0.24 0.219,0.219 10 false *1

Text in Illustration
*1 Chain Sub-assembly *2 Exhaust VVT-i Controller (Camshaft Timing Exhaust Gear Assembly)
*3 No. 1 Chain Tensioner Assembly *4 Chain Tensioner Slipper
*5 Crankshaft Timing Gear *6 Crankshaft
*7 No. 1 Chain Vibration Damper *8 Intake VVT-i Controller (Camshaft Timing Gear Assembly)
*9 Timing Chain Guide - -



p.

Valve Lash Adjuster Assembly

i.

The valve lash adjuster assembly, which is located at the fulcrum (pivot point) of the valve rocker arm sub-assemblies, consists primarily of a plunger, a plunger spring, a check ball, and a check ball spring.


ii.

The engine oil supplied from the cylinder head and the built-in spring actuate the valve lash adjuster assembly. The oil pressure and the spring force, that act on the plunger, push the valve rocker arm sub-assembly against the cam, in order to adjust the clearance between the valve stem and rocker arm. This prevents the generation of noise during the opening and closing of the valves. As a result, engine noise has been reduced.

U149557E02
1.854,0.969 1.708,0.625 1.708,0.625 1.552,0.625 true 2.052,2.385 1.531,2.01 1.531,2.01 1.406,2.01 true 2.031,2.5 1.438,2.5 true 2.427,1.792 2.625,1.333 2.625,1.333 2.813,1.333 true 4.635,1.563 3.854,1.229 3.854,1.229 3.719,1.229 true 4.708,1.49 4.115,0.521 4.115,0.521 3.885,0.521 true 4.979,0.594 5.094,0.333 5.094,0.333 5.198,0.333 true 5.135,1.177 5.49,0.573 5.49,0.573 5.635,0.573 true 1.375,0.51 1.552,0.74 0.177,0.229 10 false *1 1.229,1.896 1.417,2.125 0.188,0.229 10 false *2 1.271,2.385 1.469,2.604 0.198,0.219 10 false *3 1.458,2.865 1.635,3.094 0.177,0.229 10 false *4 2.833,1.208 3.063,1.448 0.229,0.24 10 false *5 3.542,1.125 3.74,1.396 0.198,0.271 10 false *5 3.708,0.406 3.917,0.646 0.208,0.24 10 false *6 5.24,0.219 5.448,0.49 0.208,0.271 10 false *7 5.667,0.469 5.906,0.729 0.24,0.26 10 false *8

Text in Illustration
*1 Plunger *2 Check Ball
*3 Check Ball Spring *4 Plunger Spring
*5 Oil Passage *6 Valve Lash Adjuster Assembly
*7 Cam *8 Valve Rocker Arm Sub-assembly



q.

Timing Chain Cover

i.

The components listed below have been integrated in the timing chain cover to reduce the number of parts (water pump swirl chamber, thermostat housing, oil pump housing, alternator bracket and power steering vane pump bracket).


ii.

A service hole for the chain tensioner is provided in consideration of serviceability.

W127094E02
2.5,3.552 3.26,3.125 true 2.365,2.365 3.125,2.396 true 2.063,1.125 2.823,1.24 true 2.01,0.573 2.375,0.781 true 4.688,2.292 4.177,2.198 true 1.844,0.427 2.031,0.656 0.188,0.229 10 false *1 4.729,2.208 4.99,2.49 0.26,0.281 10 false *5 2.333,3.479 2.552,3.688 0.219,0.208 10 false *4 2.188,2.25 2.385,2.49 0.198,0.24 10 false *3 1.875,1.01 2.073,1.24 0.198,0.229 10 false *2

Text in Illustration
*1 Alternator Bracket *2 Service Hole
*3 Water Pump Assembly *4 Oil Pump
*5 Thermostat Housing - -



r.

V-ribbed Belt

i.

Accessory components are driven by a serpentine belt consisting of a single V-ribbed belt. It reduces the overall engine length, weight and number of engine parts.


ii.

An automatic tensioner eliminates the need for tension adjustment.

W102320E02
2.375,1.5 2.063,0.99 2.063,0.99 1.823,0.99 true 2.906,2.25 2.396,2.813 2.396,2.813 2.135,2.813 true 3.375,2.885 3.375,3.458 3.375,3.458 3.177,3.458 true 4.438,1.375 4.802,0.729 4.802,0.729 5.052,0.729 true 3.917,1.927 5.115,1.927 true 4.479,2.667 4.875,3.281 4.875,3.281 5.104,3.281 true 1.646,0.865 1.833,1.094 0.188,0.229 10 false *1 1.948,2.698 2.156,2.969 0.208,0.271 10 false *2 3,3.333 3.198,3.583 0.198,0.25 10 false *3 5.094,0.615 5.313,0.896 0.219,0.281 10 false *4 5.156,1.813 5.385,2.104 0.229,0.292 10 false *5 5.146,3.177 5.396,3.458 0.25,0.281 10 false *6

Text in Illustration
*1 Alternator Pulley *2 Automatic Tensioner
*3 Crankshaft Pulley *4 Power Steering Pump Pulley
*5 Water Pump Pulley *6 Air Conditioning Compressor Pulley




OPERATION


a.

Balance Shaft

i.

In the in-line 4-cylinder engine, the crankshaft angle for No. 1 and No. 4 cylinders are at the exact opposite (180°) positions of No. 2 and No. 3 cylinders. Therefore, the inertial force of the pistons and the connecting rods of the former 2 cylinders and of the latter 2 cylinders almost cancel each other out. However, because the position at which the piston reaches its maximum speed is located toward the top dead center from the center of the stroke, the upward inertial force is greater than the downward inertial force. This unbalanced secondary inertial force is generated twice for each rotation of the crankshaft.

W100394E04
3.094,1.865 2.813,1.646 2.813,1.646 2.667,1.646 true 3.198,1.563 3.094,1.063 3.094,1.063 2.865,1.063 true 4.083,1.854 4.375,1.688 4.375,1.688 4.552,1.688 true 3.594,1.323 3.958,1.01 3.958,1.01 4.146,1.01 true 3.594,0.646 3.781,0.469 3.781,0.469 3.927,0.469 true 3.594,0.292 3.76,0.135 3.76,0.135 3.917,0.135 true 3.969,0.052 5.385,0.333 1.417,0.281 10 Top Dead Center 3.979,0.396 5.396,0.677 1.417,0.281 10 Point of Max. Speed 4.188,0.927 5.604,1.208 1.417,0.281 10 Bottom Dead Center 4.615,1.604 6.031,1.885 1.417,0.281 10 Point of Max. Speed 1.365,1.552 2.781,1.833 1.417,0.281 10 Point of Max. Speed 2.625,0.979 2.885,1.26 0.26,0.281 10 90°

W100395E19
2.219,0.958 2.406,0.958 2.406,0.958 2.635,1.458 false 2.646,1.948 2.385,1.698 2.385,1.698 2.26,1.698 false 3.583,1.542 3.813,0.969 3.813,0.969 3.948,0.969 true 3.833,1.948 3.833,1.375 3.833,1.375 3.969,1.375 true 3.531,1.365 3.344,1.042 3.344,1.042 3.219,1.042 false 3.229,1.958 3.229,1.333 3.229,1.333 3.073,1.333 true 4.969,1.979 4.969,1.406 4.969,1.406 5.135,1.406 true 2.667,2.896 2.448,3.063 2.448,3.063 2.271,3.063 false 0.552,0.854 2.167,1.615 1.615,0.76 10 false Inertial Force of No. 2 and No. 3 Cylinders 0.354,1.594 2.188,2.948 1.833,1.354 10 false Combined Inertial Force of All Cylinders (Unbalanced Secondary Inertial Force) 0.615,2.958 2.229,3.76 1.615,0.802 10 false Inertial Force of No. 1 and No. 4 Cylinders 2.49,2.271 2.875,2.469 0.385,0.198 10 false -180° 3.573,2.208 3.74,2.427 0.167,0.219 10 false 0° 4.302,2.271 4.667,2.479 0.365,0.208 10 false 180° 2.76,1.26 3.073,1.51 0.313,0.25 10 false -90° 4.021,1.271 4.302,1.51 0.281,0.24 10 false 90° 5.177,1.323 5.573,1.573 0.396,0.25 10 false 270° 4,0.896 6.792,1.24 2.792,0.344 10 false Inertial Force that Cannot be Canceled 2.781,0.938 3.219,1.271 0.438,0.333 10 false Force 0.146,0.073 3.396,0.5 3.25,0.427 10 false Inertial Force Generated by 4 In-line Cylinders 5.333,2.094 6.677,2.469 1.344,0.375 10 false Crankshaft Angle


ii.

To cancel the unbalanced secondary inertial force, 2 balance shafts are rotated twice for each rotation of the crankshaft and generate inertial force in the opposite direction. Also, in order to cancel the inertial force generated by the balance shaft itself, the balance shaft actually consists of 2 shafts rotating in opposite directions.

W100396E13
2.844,1.115 2.615,0.823 2.615,0.823 2.469,0.823 true 3.469,1.104 3.26,0.49 3.26,0.49 3.125,0.49 true 4.135,1.115 3.927,0.51 3.927,0.51 3.792,0.51 true 4.76,1.135 4.552,0.531 4.552,0.531 4.417,0.531 true 4.948,0.865 5.052,0.542 5.052,0.542 5.188,0.542 true 5.313,2.833 5.5,2.031 5.5,2.031 5.708,2.031 true 5.146,3 5.719,3 true 4.948,1.385 5.094,1.604 5.094,1.604 5.198,1.604 true 2.313,0.75 2.469,0.927 0.156,0.177 10 false 0° 3.49,0.417 3.833,0.635 0.344,0.219 10 false 180° 2.896,0.406 3.188,0.635 0.292,0.229 10 false 90° 4.125,0.438 4.469,0.656 0.344,0.219 10 false 270° 2.688,1.156 2.844,1.333 0.156,0.177 10 false A 3.115,1.25 3.271,1.427 0.156,0.177 10 false B 3.427,1.198 3.583,1.375 0.156,0.177 10 false C 3.771,1.25 3.927,1.427 0.156,0.177 10 false D 4.104,1.198 4.26,1.375 0.156,0.177 10 false E 0.177,0.052 3.698,0.406 3.521,0.354 10 false Mass Direction of Balance Shaft at Crankshaft Angle 5.229,0.448 7.156,0.823 1.927,0.375 10 false Inertial Force of Balancer 5.229,1.052 6.844,1.333 1.615,0.281 10 false Crankshaft Angle 5.229,1.521 7.031,1.948 1.802,0.427 10 false Secondary Inertial Force 5.771,1.948 6.865,2.833 1.094,0.885 10 false Mass Direction of Balance Shaft 5.76,2.917 6.76,3.708 1,0.792 10 false Inertial Force of Balancer