Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2015.06–2020.08
NM27T0E _51 Engine / Hybrid System _053579 1KD-FTV ENGINE MECHANICAL _0260104 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

1KD-FTV ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Cylinder Head Cover

i.

The cylinder head cover is made of plastic to reduce weight and noise.


ii.

A baffle plate is provided on the inside of the cylinder head cover to reduce the consumption of engine oil through blow-by gas.

W127878E02
1.906,3.354 1.594,3.125 true 5.896,1.604 6.052,1.208 true 1.229,0.875 0.927,0.646 true 0.344,2.792 0.479,2.979 0.135,0.188 10 false A 2.49,1.802 2.625,1.99 0.135,0.188 10 false A 5.448,2.063 5.667,2.25 0.219,0.188 10 false *a 1.927,3.323 2.146,3.51 0.219,0.188 10 false *2 0.76,0.5 0.979,0.688 0.219,0.188 10 false *1 6.021,1.042 6.24,1.229 0.219,0.188 10 false *3

Text in Illustration
*1 No. 2 Cylinder Head Cover *2 Cylinder Head Cover
*3 Baffle Plate - -
*a A - A Cross Section - -



b.

Cylinder Head Gasket

i.

A steel-laminate type cylinder head gasket is used.


ii.

A shim has been provided around the cylinder bore to increase the sealing surface, thus achieving excellent sealing performance.

W102270E03
0.594,0.406 0.438,0.25 0.438,0.25 0.344,0.25 true 3.74,0.396 4.021,0.167 true 3.74,0.521 4.021,0.75 true 3.74,0.458 4.021,0.458 true 3.74,1.448 4.021,1.583 true 3.74,1.385 4.021,1.26 true 5.677,0.896 5.813,0.375 5.813,0.375 5.917,0.375 true 0.156,0.156 0.344,0.344 0.188,0.188 10 false *1 5.948,1.104 6.135,1.292 0.188,0.188 10 false *a 4.958,0.719 5.146,0.906 0.188,0.188 10 false *b 5.958,0.292 6.26,0.521 0.302,0.229 10 false *2 6.906,0.719 7.094,0.906 0.188,0.188 10 false *c 1.948,0.115 2.083,0.302 0.135,0.188 10 false F 4.031,0.031 4.156,0.188 0.125,0.156 10 false A 4.063,0.396 4.188,0.542 0.125,0.146 10 false B 4.031,0.729 4.156,0.885 0.125,0.156 10 false C 4.031,1.135 4.156,1.281 0.125,0.146 10 false D 4.031,1.573 4.156,1.729 0.125,0.156 10 false E 1.698,0.76 1.823,0.948 0.125,0.188 10 false F

Text in Illustration
*1 Cylinder Head Gasket *2 Shim
*a F - F Cross Section *b Cylinder Bore Side
*c Outer Side - -
V100136

Front - -

HINT:

There are 5 sizes of new cylinder head gaskets, marked "A", "B", "C", "D", or "E" in accordance with piston protrusion. For details, refer to the Repair Manual.




c.

Cylinder Head

i.

The cylinder head is made of aluminum alloy. The injector has been located in the center of the combustion chamber in order to improve engine performance and to achieve cleaner emissions.


ii.

Two intake ports with different shapes have been combined to promote the mixture of fuel and air by optimizing the swirl in the cylinder.


iii.

A vertical 2-stage construction is used for the water jacket to improve cooling performance.


iv.

A glow plug is placed between the intake ports of each cylinder to ensure startability.


v.

The passage for the EGR is provided in the cylinder head. By cooling the exhaust gas, it is possible to recirculate a large amount of exhaust gas.


vi.

On the models without EGR control, an EGR hole cover plate which plugs the EGR passage is provided.


vii.

The cylinder head bolt employs plastic region tightening bolts.

W102271E03
1.531,0.26 1.531,1.396 true 0.708,2.271 0.708,2.5 true 1.531,1.635 1.531,2.542 true 5.156,2.073 4.792,2.552 true 4.885,1.542 4.073,2.594 true 0.625,2.51 0.813,2.698 0.188,0.188 10 false *2 1.458,2.552 1.698,2.75 0.24,0.198 10 false *3 1.438,0.063 1.625,0.25 0.188,0.188 10 false *1 1.313,1.031 1.5,1.219 0.188,0.188 10 false *4 1.688,1.021 1.875,1.208 0.188,0.188 10 false *4 1.677,1.531 1.865,1.719 0.188,0.188 10 false *5 1.229,1.531 1.417,1.719 0.188,0.188 10 false *5 2.406,1.042 2.594,1.229 0.188,0.188 10 false *4 2.781,1.031 2.969,1.219 0.188,0.188 10 false *4 2.781,1.531 2.969,1.719 0.188,0.188 10 false *5 4.646,2.531 4.833,2.719 0.188,0.188 10 false *6 2.323,1.531 2.51,1.719 0.188,0.188 10 false *5 3.927,2.573 4.115,2.76 0.188,0.188 10 false *6

Text in Illustration
*1 Injector Hole *2 EGR Passage
*3 Glow Plug Hole *4 Exhaust Valve Hole
*5 Intake Valve Hole *6 Water Jacket



d.

Cylinder Block

i.

The cylinder block is constructed of liner-less cast iron alloy.

W102703



e.

Piston

i.

A piston provided with a combustion chamber is used.


ii.

The piston is made of aluminum alloy.


iii.

A cooling channel has been provided to reduce the piston temperature, and achieve high reliability.


iv.

The top ring groove uses a Ni-resist cast iron ring carrier to improve wear resistance.


v.

A Physical Vapor Deposition (PVD) coating has been applied to the surface of the No. 1 compression ring, in order to improve its wear resistance.


vi.

Except on the models compliant with EURO 4 emission regulations, a chromium plating coating has been applied to the surface of the No. 2 compression ring, in order to improve its wear resistance.


vii.

Except on the models compliant with EURO 4 emission regulations, a PVD coating has been applied to the surface of the oil ring.


viii.

A resin coating is applied to the piston skirt portion, to achieve reduction of friction loss.

W127879E02
6.135,1.865 6.198,1.802 6.198,1.802 6.344,1.802 true 6.167,2.052 6.229,1.99 6.229,1.99 6.354,1.99 true 5,0.938 5.156,0.938 true 6.281,0.948 6.438,0.948 true 6.292,1.417 6.469,1.417 true 1.406,1.104 0.938,1.573 true 1.51,1.208 1.01,2 true 2.833,0.365 2.615,0.646 true 2.875,1.906 2.667,1.615 true 5.188,0.865 5.396,1.042 0.208,0.177 10 false *b 0.771,1.521 0.948,1.698 0.177,0.177 10 false *2 0.865,1.99 1.125,2.26 0.26,0.271 10 false *3 4.146,0.74 4.354,0.917 0.208,0.177 10 false *4 4.167,1.24 4.375,1.417 0.208,0.177 10 false *5 4.177,1.719 4.385,1.896 0.208,0.177 10 false *6 5.521,0.76 5.729,0.938 0.208,0.177 10 false *4 5.51,1.219 5.719,1.396 0.208,0.177 10 false *5 5.51,1.708 5.719,1.885 0.208,0.177 10 false *6 4.656,0.51 4.938,0.688 0.281,0.177 12 false *A: 6.01,0.521 6.292,0.698 0.281,0.177 12 false *B: 6.385,1.719 6.594,1.896 0.208,0.177 10 false *b 6.396,1.906 6.646,2.104 0.25,0.198 10 false *b 2.823,0.208 3,0.385 0.177,0.177 10 false *1 6.469,0.865 6.677,1.042 0.208,0.177 10 false *b 6.5,1.344 6.708,1.521 0.208,0.177 10 false *c 2.896,1.906 3.167,2.146 0.271,0.24 10 false *a

Text in Illustration
*A Models Compliant with EURO 4 Emission Regulations *B Except Models Compliant with EURO 4 Emission Regulations
*1 Piston *2 Ni-resist Cast Iron Ring Carrier
*3 Cooling Channel *4 No. 1 Compression Ring
*5 No. 2 Compression Ring *6 Oil Ring
*a Resin Coating *b PVD Coating
*c Chromium Plating - -



f.

Connecting Rod Sub-assembly and Connecting Rod Bearing

i.

The connecting rods are made of high-strength material to ensure the proper strength.


ii.

Knock pins are used at the mating surfaces of the bearing caps of the connecting rod to minimize the shifting of the bearing caps during assembly.


iii.

Plastic region tightening bolts are used.


iv.

An aluminum bearing is used for the connecting rod bearings.


v.

The lining surface of the connecting rod bearing has been micro-grooved to achieve an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibrations have been reduced.

W102274E02
1.552,2.448 1.458,2.604 1.458,2.604 1.292,2.604 true 2.313,2.448 2.417,2.604 2.417,2.604 2.573,2.604 true 1.698,0.469 1.417,0.469 true 2.302,2.083 2.583,1.813 2.583,1.813 2.677,1.813 true 4.51,0.729 4.302,0.531 4.302,0.531 4.177,0.531 true 4.094,2.052 4.448,2.406 4.448,2.406 4.667,2.406 true 1.26,0.406 1.427,0.573 0.167,0.167 10 false *1 4.01,0.458 4.25,0.688 0.24,0.229 10 false *4 4.719,2.313 4.885,2.479 0.167,0.167 10 false *5 2.719,1.729 3.021,2.042 0.302,0.313 10 false *2 1.146,2.531 1.313,2.698 0.167,0.167 10 false *3 2.594,2.531 2.76,2.698 0.167,0.167 10 false *3

Text in Illustration
*1 Connecting Rod Sub-assembly *2 Knock Pin
*3 Plastic Region Tightening Bolt *4 Connecting Rod Bearing
*5 Micro-grooved - -



g.

Crankshaft and Crankshaft Bearing

i.

The crankshaft has 5 journals and 8 balance weights.


ii.

All pin and journal fillets are roll-finished to maintain adequate strength.


iii.

The crankshaft bearing is made of aluminum alloy.


iv.

The lining surface of the crankshaft bearing has been micro-grooved to achieve an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibrations have been reduced.


v.

The upper main bearing has an oil groove around its inside circumference.

W102275E02
0.427,1.302 0.427,0.615 0.427,0.615 0.323,0.615 true 0.979,1.177 0.979,0.313 0.979,0.313 0.885,0.313 true 1.365,0.906 1.365,0.188 1.365,0.188 1.469,0.188 true 1.667,1.167 1.844,0.198 1.844,0.198 1.958,0.198 true 4.115,1.198 4.208,0.635 4.208,0.635 4.281,0.635 true 2.052,1.552 2.219,0.583 2.219,0.583 2.344,0.583 true 1.875,1.625 1.698,2.583 1.698,2.583 1.573,2.583 true 2.26,1.938 2.135,2.583 2.135,2.583 2.063,2.583 true 3.521,1.906 3.521,2.156 true 5.729,0.469 5.5,0.25 5.5,0.25 5.375,0.25 true 6.302,1.583 6.51,1.781 6.51,1.781 6.635,1.781 true 5.75,0.677 5.229,1.188 5.229,1.188 5.135,1.188 true 5.219,2.208 4.979,2.448 4.979,2.448 4.792,2.448 true 0.688,0.219 0.906,0.49 0.219,0.271 10 false *2 1.5,0.104 1.74,0.344 0.24,0.24 10 false *3 0.156,0.531 0.344,0.719 0.188,0.188 10 false *1 1.979,0.094 2.167,0.281 0.188,0.188 10 false *4 2.365,0.5 2.552,0.688 0.188,0.188 10 false *4 1.406,2.51 1.594,2.698 0.188,0.188 10 false *4 3.448,2.167 3.729,2.417 0.281,0.25 10 false *5 4.323,0.563 4.719,0.833 0.396,0.271 10 false *6 5.198,0.188 5.417,0.438 0.219,0.25 10 false *7 6.656,1.708 6.844,1.896 0.188,0.188 10 false *8 4.958,1.104 5.271,1.354 0.313,0.25 10 false *9 4.552,2.344 4.813,2.563 0.26,0.219 10 false *10 1.896,2.51 2.083,2.698 0.188,0.188 10 false *4

Text in Illustration
*1 Crankshaft *2 No. 1 Journal
*3 Oil Hole *4 Roll-finished
*5 Balance Weight *6 No. 5 Journal
*7 Upper Main Bearing *8 Lower Main Bearing
*9 Oil Groove *10 Micro-grooved



h.

Balance Shaft

i.

For in-line 4-cylinder engines, the main cause of vibration is the imbalanced inertial force of reciprocating parts, such as the pistons and connecting rods. Engine vibration has been reduced by using 2 balance shafts to cancel the imbalanced inertial force, thereby reducing engine noise (booming noise).


ii.

These balance shafts are built into the cylinder block. Driven by the timing gear, the balance shafts rotate at twice the speed of the crankshaft and in the opposite direction of each other.

W102276E02
2.438,1.333 1.563,0.458 1.563,0.458 1.375,0.458 true 4.708,1.26 5.583,0.385 5.583,0.385 5.771,0.385 true 3.51,1.99 4.073,2.552 4.073,2.552 4.188,2.552 true 2.896,2.406 2.656,2.646 2.656,2.646 2.615,2.646 true 2.583,2.198 2.344,2.427 2.344,2.427 2.302,2.427 true 2.313,1.917 2.083,2.146 2.083,2.146 2.031,2.146 true 5.802,0.302 6.198,0.656 0.396,0.354 10 false *2 4.229,2.458 4.417,2.646 0.188,0.188 10 false *3 1.198,0.354 1.438,0.625 0.24,0.271 10 false *1 2.438,2.542 2.625,2.729 0.188,0.188 10 false *4 2.115,2.344 2.333,2.531 0.219,0.188 10 false *5 1.854,2.042 2.094,2.292 0.24,0.25 10 false *6

Text in Illustration
*1 No. 1 Balance Shaft Sub-assembly *2 No. 2 Balance Shaft Sub-assembly
*3 Supply Pump Drive Gear *4 Idle Gear
*5 Crankshaft Timing Gear *6 Oil Pump Drive Gear



i.

Oil Pan

i.

The oil pan sub-assembly material is made of aluminum alloy.


ii.

The oil passage has been integrated in the oil pan to simplify the construction of the oil strainer.

W102277E02
1.448,0.76 1.698,0.51 1.698,0.51 1.844,0.51 true 5.25,1.5 5.5,0.688 5.5,0.688 5.635,0.688 true 1.135,0.594 1.135,0.198 1.135,0.198 1.052,0.198 true 2.49,2.219 2.719,2.458 2.719,2.458 2.865,2.458 true 1.896,0.417 2.198,0.646 0.302,0.229 10 false *2 2.906,2.375 3.094,2.563 0.188,0.188 10 false *3 5.688,2.094 5.875,2.281 0.188,0.188 10 false *a 0.167,0.292 0.354,0.479 0.188,0.188 10 false A 3.719,1.302 3.906,1.49 0.188,0.188 10 false A 0.885,0.104 1.073,0.292 0.188,0.188 10 false *1 5.677,0.604 6.042,0.896 0.365,0.292 10 false *2

Text in Illustration
*1 Oil Pan Sub-assembly *2 Oil Passage
*3 No. 2 Oil Pan Sub-assembly - -
*a A - A Cross Section - -



j.

Valve Mechanism

i.

Each cylinder has 2 intake valves and 2 exhaust valves. Intake and exhaust efficiency is increased by means of the larger total port areas.


ii.

The valves are directly opened and closed by 2 camshafts.


iii.

The camshaft (intake camshaft) is driven by a timing belt, while the No. 2 camshaft (exhaust camshaft) is driven by gears on the camshaft (intake camshaft).


iv.

Small-diameter, flat-teeth gears are used for driving the No. 2 camshaft (exhaust camshaft) in order to reduce gear noise.

W102278E02
2.708,1.073 1.458,1.073 true 2.781,0.625 2.781,0.198 true 2.896,0.677 2.896,0.365 2.896,0.365 2.792,0.365 true 4.167,0.583 4.51,0.25 4.51,0.25 4.729,0.25 true 4.354,0.656 4.5,0.51 4.5,0.51 4.708,0.51 true 4.354,1.865 5.135,2.635 5.135,2.635 5.24,2.635 true 3.625,1.729 5.104,3.208 5.104,3.208 5.302,3.208 true 1.292,0.99 1.542,1.198 0.25,0.208 10 false *1 4.75,0.417 4.917,0.583 0.167,0.167 10 false *4 5.271,2.552 5.521,2.75 0.25,0.198 10 false *5 5.344,3.125 5.698,3.292 0.354,0.167 10 false *5 2.688,0.021 2.865,0.198 0.177,0.177 10 false *2 4.74,0.135 4.906,0.302 0.167,0.167 10 false *3

Text in Illustration
*1 Timing Belt *2 Camshaft Drive Gear
*3 No. 2 Camshaft (Exhaust Camshaft) *4 Camshaft (Intake Camshaft)
*5 Balance Shaft - -



k.

Camshaft

i.

The cam nose has been chill-treated to increase its abrasion resistance.

W102279E03
1.906,0.875 1.75,0.719 1.75,0.719 1.604,0.719 true 2.135,0.729 1.74,0.333 1.74,0.333 1.625,0.333 true 2.333,1.51 2.219,1.625 2.219,1.625 2.083,1.625 true 2.844,1.479 2.948,1.583 2.948,1.583 3.094,1.583 true 1.448,0.26 1.708,0.49 0.26,0.229 10 false *2 1.927,1.531 2.115,1.719 0.188,0.188 10 false *3 3.104,1.51 3.292,1.698 0.188,0.188 10 false *4 1.458,0.625 1.708,0.865 0.25,0.24 10 false *1

Text in Illustration
*1 No. 2 Camshaft (Exhaust Camshaft) *2 Camshaft Driven Gear
*3 Camshaft (Intake Camshaft) *4 Camshaft Drive Gear
V100144

Chill-treated - -



l.

Intake and Exhaust Valves

i.

Along with the increased amount of valve lift, shim-less valve lifters that provide a large cam contact surface are used.


ii.

The adjustment of the valve clearance is accomplished by selecting and replacing the appropriate valve lifters.

W102280E02
2.563,0.469 3.281,0.469 true 3.844,1.031 4.563,1.031 true 4.604,0.958 4.792,1.146 0.188,0.188 10 false *2 2.375,0.406 2.563,0.594 0.188,0.188 10 false *1

Text in Illustration
*1 Camshaft *2 Valve Lifter

HINT:

The valve lifters must be replaced when it is necessary to adjust the valve clearance. For this purpose, valve lifters with different thicknesses are available as service parts. For details, refer to the Repair Manual.




m.

Timing Gear Train

i.

The supply pump, vacuum pump, oil pump and balance shafts are driven by the crankshaft timing gear.


ii.

The idle gear is constructed with a scissors gear on its front and back to reduce noise.

W102281E03
1.167,0.406 1.885,0.406 true 1.448,2.042 2.156,2.042 true 1.74,2.51 2.458,2.51 true 4.896,2.417 5.615,2.417 true 3.26,1.656 3.646,1.656 true 3.729,1.167 3.729,0.323 3.729,0.323 3.531,0.323 true 4.458,1.656 4.458,0.813 4.458,0.813 4.26,0.813 true 4.792,1.323 4.792,0.469 4.792,0.469 4.99,0.469 true 4.385,2.448 4.135,2.698 4.135,2.698 4.073,2.698 true 4.063,2.281 3.813,2.521 3.813,2.521 3.75,2.521 true 0.979,0.323 1.219,0.51 0.24,0.188 10 false *1 1.271,1.969 1.458,2.156 0.188,0.188 10 false *2 1.573,2.438 1.76,2.625 0.188,0.188 10 false *3 3.365,0.24 3.594,0.5 0.229,0.26 10 false *4 4.083,0.729 4.271,0.917 0.188,0.188 10 false *4 5.021,0.385 5.333,0.656 0.313,0.271 10 false *5 5.625,2.333 5.813,2.521 0.188,0.188 10 false *6 3.906,2.604 4.094,2.792 0.188,0.188 10 false *7 3.594,2.427 3.781,2.615 0.188,0.188 10 false *8 3.083,1.563 3.313,1.781 0.229,0.219 10 false *9

Text in Illustration
*1 No. 2 Camshaft Timing Pulley *2 Automatic Tensioner
*3 No. 1 Camshaft Timing Pulley *4 Balance Shaft Drive Gear
*5 Supply Pump Drive Gear *6 Vacuum Pump Drive Gear
*7 Idle Gear *8 Crankshaft Timing Gear
*9 Oil Pump Drive Gear - -



n.

Timing Gear Cover

i.

A crank position sensor and camshaft position sensor are mounted on the timing gear cover.

W102282E03
2.823,1.115 2.823,0.333 true 1.49,2.531 0.917,1.958 0.917,1.958 0.75,1.958 true 5.625,0.438 5.906,0.729 5.906,0.729 6.094,0.729 true 2.74,0.146 2.927,0.333 0.188,0.188 10 false *1 6.135,0.646 6.323,0.833 0.188,0.188 10 false *3 0.573,1.875 0.76,2.063 0.188,0.188 10 false *2

Text in Illustration
*1 Timing Gear Cover *2 Crank Position Sensor
*3 Camshaft Position Sensor - -



o.

V-ribbed Belt

i.

Accessory components are driven by a serpentine belt consisting of a single V-ribbed belt. This reduces the overall engine length, weight and the number of engine parts.


ii.

An automatic tensioner eliminates the need for tension adjustment.

W128650E02
1.979,1.969 2.219,2.198 0.24,0.229 10 false *1 5.333,1.688 5.573,1.917 0.24,0.229 10 false *2 0.646,0.125 0.885,0.354 0.24,0.229 12 false *A: 4.396,0.125 4.635,0.354 0.24,0.229 12 false *B: 1.063,1.76 1.302,1.99 0.24,0.229 10 false *3 1.938,1.302 2.177,1.531 0.24,0.229 10 false *4 1.49,1.271 1.729,1.5 0.24,0.229 10 false *5 5.042,0.385 5.281,0.615 0.24,0.229 10 false *7 4.906,0.979 5.146,1.208 0.24,0.229 10 false *6 1.115,1 1.354,1.229 0.24,0.229 10 false *6 5.281,1.271 5.521,1.5 0.24,0.229 10 false *5 5.49,0.896 5.729,1.125 0.24,0.229 10 false *5 1.688,0.896 1.927,1.125 0.24,0.229 10 false *5 5.729,1.302 5.969,1.531 0.24,0.229 10 false *4 4.844,1.76 5.083,1.99 0.24,0.229 10 false *3 1.531,1.677 1.771,1.906 0.24,0.229 10 false *2 5.76,1.958 6,2.188 0.24,0.229 10 false *1

Text in Illustration
*A Models without Power Heater *B Models with Power Heater
*1 Crankshaft Pulley *2 Idler Pulley for Automatic Tensioner
*3 Generator Pulley *4 Water Pump Pulley
*5 Idler Pulley *6 Air Conditioning Compressor Pulley
*7 Power Heater Pulley - -



p.

Engine Mount

i.

Electrical hydraulic type engine mounts are used for the front engine mounts.


ii.

The front engine mount consists primarily of the rubber portion, No. 1 fluid chamber, No. 2 fluid chamber, and diaphragm. Fluid is sealed in the No. 1 and No. 2 fluid chambers.


iii.

This engine mount obtains a vacuum from the vacuum pump via the VSV. It utilizes the vacuum to pull the diaphragm down in order to open or close the passages that connect the No. 1 and No. 2 fluid chambers.


iv.

The No. 1 and No. 2 fluid chambers use two fluid passages: the No. 1 fluid passage that is always connected regardless of whether the diaphragm is open or closed; and the No. 2 fluid passage that is connected only when the diaphragm is open. The fluid flows back and forth between the No. 1 and No. 2 fluid chambers through these two passages in order to restrain the vibration.

W102284E02
3.594,1.885 3.99,2.5 3.99,2.5 4.844,2.5 true 3.635,1.552 5.01,0.177 5.01,0.177 5.24,0.177 true 4.052,1.76 5.063,0.75 5.063,0.75 5.229,0.75 true 4.021,2.104 5.219,2.104 true 3.563,2.583 2.677,2.271 2.677,2.271 2.063,2.271 true 3.469,1.927 2.479,1.469 2.479,1.469 2.083,1.469 true 3.469,1.375 2.479,0.927 2.479,0.927 2.083,0.927 true 1.208,2.177 2.073,2.5 0.865,0.323 10 false Vacuum Port 5.281,0.667 6.656,1.021 1.375,0.354 10 false No. 1 Fluid Passage 0.771,1.375 2.094,1.729 1.323,0.354 10 false No. 2 Fluid Passage 1.594,0.833 2.094,1.188 0.5,0.354 10 false Rubber 0.792,0.281 1.292,0.51 0.5,0.229 10 false : Fluid 5.333,0.083 6.708,0.406 1.375,0.323 10 false No. 1 Fluid Chamber 5.281,2.031 6.656,2.354 1.375,0.323 10 false No. 2 Fluid Chamber 4.885,2.417 5.635,2.74 0.75,0.323 10 false Diaphragm




OPERATION


a.

Balance Shaft

i.

In the in-line 4-cylinder engine, the crankshaft angle for No. 1 and No. 4 cylinders are at the exact opposite (180°) positions of No. 2 and No. 3 cylinders. Therefore, the inertial force of the pistons and the connecting rods of the former 2 cylinders and of the latter 2 cylinders almost cancel each other out. However, because the position at which the piston reaches its maximum speed is located toward the top dead center from the center of the stroke, the upward inertial force is greater than the downward inertial force. This unbalanced secondary inertial force is generated twice for each rotation of the crankshaft.

W100394E14
3.083,1.865 2.802,1.646 2.802,1.646 2.656,1.646 false 3.198,1.563 3.094,1.063 3.094,1.063 2.865,1.063 true 4.083,1.854 4.375,1.688 4.375,1.688 4.552,1.688 true 3.594,1.323 3.958,1.01 3.958,1.01 4.146,1.01 true 3.594,0.646 3.781,0.469 3.781,0.469 3.927,0.469 false 3.594,0.302 3.76,0.146 3.76,0.146 3.917,0.146 false 3.969,0.052 5.385,0.333 1.417,0.281 10 false Top Dead Center 3.979,0.396 5.396,0.677 1.417,0.281 10 false Point of Max. Speed 4.188,0.927 5.604,1.208 1.417,0.281 10 false Bottom Dead Center 4.615,1.604 6.031,1.885 1.417,0.281 10 false Point of Max. Speed 1.365,1.552 2.781,1.833 1.417,0.281 10 false Point of Max. Speed 2.625,0.979 2.885,1.26 0.26,0.281 10 false 90°

W100395E23
2.219,0.958 2.406,0.958 2.406,0.958 2.635,1.458 false 2.646,1.938 2.385,1.688 2.385,1.688 2.26,1.688 false 3.583,1.51 3.813,0.938 3.813,0.938 3.948,0.938 true 3.854,1.958 3.854,1.385 3.854,1.385 3.99,1.385 true 3.531,1.354 3.344,1.031 3.344,1.031 3.219,1.031 false 3.219,1.958 3.219,1.333 3.219,1.333 3.063,1.333 true 4.99,1.948 4.99,1.375 4.99,1.375 5.156,1.375 true 2.698,2.635 2.396,2.958 2.396,2.958 2.229,2.958 false 0.583,0.865 2.188,1.563 1.604,0.698 10 false Inertial Force of No. 2 and No. 3 Cylinders 0.406,1.594 2.219,2.542 1.813,0.948 10 false Combined Inertial Force of All Cylinders (Unbalanced Secondary Inertial Force) 0.615,2.865 2.208,3.708 1.594,0.844 10 false Inertial Force of No. 1 and No. 4 Cylinders 2.5,2.271 2.917,2.542 0.417,0.271 10 false -180° 3.573,2.219 3.74,2.479 0.167,0.26 10 false 0° 4.292,2.271 4.656,2.51 0.365,0.24 10 false 180° 2.802,1.25 3.135,1.5 0.333,0.25 10 false -90° 4.052,1.302 4.344,1.531 0.292,0.229 10 false 90° 5.198,1.292 5.667,1.594 0.469,0.302 10 false 270° 4,0.844 6.792,1.26 2.792,0.417 10 false Inertial Force that Cannot be Canceled 2.823,0.938 3.292,1.208 0.469,0.271 10 false Force 0.146,0.177 3.042,0.51 2.896,0.333 10 false Inertial Force Generated by In-line 4 Cylinders 5.354,2.104 6.438,2.5 1.083,0.396 10 false Crankshaft Angle


ii.

To cancel the unbalanced secondary inertial force, 2 balance shafts are rotated twice for each rotation of the crankshaft and generate inertial force in the opposite direction. Also, in order to cancel the inertial force generated by the balance shaft itself, the balance shaft actually consists of 2 shafts rotating in opposite directions.

W100396E10
2.844,1.125 2.615,0.833 2.615,0.833 2.469,0.833 false 3.469,1.115 3.083,0.5 3.083,0.5 2.917,0.5 false 4.135,1.115 3.719,0.51 3.719,0.51 3.594,0.51 false 4.771,1.115 4.396,0.521 4.396,0.521 4.25,0.521 false 4.917,0.833 5.021,0.51 5.021,0.51 5.156,0.51 false 5.302,2.854 5.49,2.052 5.49,2.052 5.698,2.052 true 5.146,3 5.719,3 true 4.958,1.365 5.104,1.583 5.104,1.583 5.208,1.583 false 2.302,0.729 2.479,0.969 0.177,0.24 10 false 0° 3.292,0.375 3.604,0.635 0.313,0.26 10 false 180° 2.677,0.375 2.906,0.646 0.229,0.271 10 false 90° 3.938,0.385 4.26,0.635 0.323,0.25 10 false 270° 2.708,1.177 2.865,1.354 0.156,0.177 10 false A 3.104,1.208 3.26,1.385 0.156,0.177 10 false B 3.427,1.177 3.583,1.354 0.156,0.177 10 false C 3.771,1.198 3.927,1.375 0.156,0.177 10 false D 4.104,1.177 4.26,1.354 0.156,0.177 10 false E 0.177,0.042 3.802,0.396 3.625,0.354 10 false Mass Direction of Balance Shaft at Crankshaft Angle 5.198,0.417 6.958,0.823 1.76,0.406 10 false Inertial Force of Balancer 5.208,1.031 6.906,1.427 1.698,0.396 10 false Crankshaft Angle 5.24,1.5 7,1.917 1.76,0.417 10 false Secondary Inertial Force 5.729,1.948 6.979,2.906 1.25,0.958 10 false Mass Direction of Balance Shaft 5.771,2.906 6.917,3.76 1.146,0.854 10 false Inertial Force of Balancer