Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SYSTEM › 2015.06–2020.08
NM27T0E _51 Engine / Hybrid System _053585 1GD-FTV FUEL _0260110 FUEL SYSTEM UN GENERAL/CONTROL/DETAILS F

1GD-FTV FUEL  FUEL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

Common-rail System

i.

In this system, the highly pressurized fuel supplied by the supply pump is stored in the common-rail, and the ECM controls the injection timing and injection volume of the injectors.

W123715E06
3.542,0.271 3.656,0.833 true 5,3.75 5.323,3.635 true 6.552,0.354 6.25,0.802 true 1.531,0.313 1.708,0.76 true 1.125,4.063 1.49,4.51 true 1.271,6.271 1.698,6.042 true 2.625,8.156 3.083,7.896 false 6.865,1.76 6.635,2.094 true 3.094,4.406 2.896,4.198 true 2.708,6.74 2.958,6.656 false 3.833,7.469 4.125,7.323 false 5.906,6.771 5.74,6.531 true 1.375,0.125 1.635,0.479 0.26,0.354 10 false *2 1.073,2 1.333,2.354 0.26,0.354 10 false *3 0.771,3.396 1.031,3.75 0.26,0.354 10 false *4 1.406,3.375 1.667,3.729 0.26,0.354 10 false *5 0.979,3.927 1.24,4.281 0.26,0.354 10 false *6 5,7.458 5.26,7.813 0.26,0.354 10 false *10 4.979,8.198 5.24,8.427 0.26,0.229 10 false *11 4.708,3.75 5.052,4.167 0.344,0.417 10 false *12 2.74,4.021 3,4.292 0.26,0.271 10 false *a 6.854,1.646 7.115,1.917 0.26,0.271 10 false *d 2.531,6.677 2.792,6.948 0.26,0.271 10 false *b 1.104,6.271 1.365,6.625 0.26,0.354 10 false *7 6.521,0.177 6.802,0.563 0.281,0.385 10 false *13 3.417,0.104 3.677,0.458 0.26,0.354 10 false *1 2.49,8.146 2.75,8.5 0.26,0.354 10 false *8 5.917,6.781 6.167,7.042 0.25,0.26 10 false *9 3.688,7.438 3.948,7.708 0.26,0.271 10 false *c

Text in Illustration
*1 Common-rail Assembly *2 Fuel Pressure Sensor
*3 ECM *4 Crank Position Sensor
*5 Cam Position Sensor *6 Pre-stroke Control Valve
*7 Injection or Supply Pump Assembly *8 Exhaust Fuel Addition Injector Assembly
*9 Pressurised Fuel Filter *10 Fuel Filter Assembly
*11 Fuel Tank Assembly *12 Injector Assembly
*13 Pressure Discharge Valve - -
*a Fuel (High Pressure) *b Fuel (Feed Pressure)
*c Fuel (Suction) *d Fuel (Return)




CONSTRUCTION


a.

Supply Pump

i.

An HP5S type injection or supply pump assembly is used.


ii.

The injection or supply pump assembly consists of a camshaft, a plunger, a check valve a pre-stroke control valve and a feed pump.

W123716E02
0.521,0.25 1.021,0.844 true 5.521,0.458 5.25,1.052 true 6.208,0.823 5.708,1.063 true 4.708,0.51 5.031,1.177 true 4.375,1.177 4.885,1.542 true 4.208,1.75 4.927,2.063 true 3.865,2.042 4.24,2.281 true 6.677,1.802 5.177,2.208 true 4.219,1.583 4.906,1.917 true 3.365,1.438 2.917,1.76 true 2.531,1.875 3.198,2.177 true 2.563,2.479 3.063,3.24 true 2.427,0.969 2.896,0.521 true 0.396,0.104 0.646,0.385 0.25,0.281 10 false *1 4.573,0.344 4.823,0.625 0.25,0.281 10 false *2 5.531,0.323 5.781,0.604 0.25,0.281 10 false *8 4.177,1.031 4.427,1.313 0.25,0.281 10 false *3 4.063,1.479 4.313,1.76 0.25,0.281 10 false *4 4.042,1.667 4.292,1.948 0.25,0.281 10 false *5 3.708,1.927 3.958,2.208 0.25,0.281 10 false *6 6.688,1.719 6.938,2 0.25,0.281 10 false *7 5.146,3.521 5.417,3.74 0.271,0.219 10 false B 5.49,3.26 5.76,3.479 0.271,0.219 10 false C 3.26,2.125 3.51,2.406 0.25,0.281 10 false *b 3.375,1.302 3.625,1.583 0.25,0.281 10 false *c 2.844,0.365 3.094,0.646 0.25,0.281 10 false *d 6.219,0.74 6.469,1.021 0.25,0.281 10 false *d 3.031,3.24 3.281,3.521 0.25,0.281 10 false *a

Text in Illustration
*1 Pre-stroke Control Valve *2 Plunger
*3 Spring *4 Shoe
*5 Roller *6 Camshaft
*7 Double Cam *8 Check Ball
*a To Exhaust Fuel Addition Injector and Pressurised Fuel Filter *b Fuel Return Port (To Pressurised Fuel Filter)
*c Fuel Inlet Port (From Fuel Tank) *d To Common-rail Assembly

Supply Pump Specifications
Type HP5S
Length B 202.2 mm (7.96 in.)
C 144.6 mm (5.69 in.)
Pre-stroke Control Valve 1
Plunger φ 6.5 mm x 1
Weight 3970 g (8.75 lb)



b.

Common-rail

i.

The function of the common-rail assembly is to store the fuel that has been pressurized by the injection or supply pump assembly.


ii.

The common-rail assembly is provided with a fuel pressure sensor and pressure discharge valve.


iii.

The fuel pressure sensor detects the fuel pressure in the common-rail assembly.


iv.

The pressure discharge valve regulates the fuel pressure. In the pressure discharge valve, the plunger opens and closes in accordance with the actuation signals from the ECM. Thus, it regulates pressure by releasing excess pressure from the common-rail assembly. In addition, it has a pressure reduction function in case of emergency.

W127925E02
1.979,0.292 2.375,1.344 true 6.063,1.583 6.365,1.948 true 0.99,0.573 1.542,1.313 true 1.813,0.083 2.219,0.406 0.406,0.323 10 false *1 0.833,0.396 1.24,0.719 0.406,0.323 10 false *2 6.333,1.948 6.74,2.271 0.406,0.323 10 false *3 2.625,0.521 3.031,0.844 0.406,0.323 10 false *a 4.333,0.521 4.74,0.844 0.406,0.323 10 false *a 3.771,0.51 4.177,0.833 0.406,0.323 10 false *b 4.865,0.542 5.271,0.865 0.406,0.323 10 false *a 5.375,0.094 5.781,0.417 0.406,0.323 10 false *c 3.156,0.49 3.563,0.813 0.406,0.323 10 false *a

Text in Illustration
*1 Common-rail Assembly *2 Fuel Pressure Sensor
*3 Pressure Discharge Valve - -
*a To Injector Assembly *b From Injection or Supply Pump Assembly
*c To Fuel Tank Assembly (Excess Pressure) - -



c.

Injector

i.

Each injector assembly consists of a nozzle needle, a control plate and a solenoid valve.


ii.

An injector compensation value and a Quick Response (QR) code containing encoded characteristics of the injector are printed on each injector.


iii.

The injector compensation value and QR code contain various pieces of information regarding the injector, such as model code and injection volume correction.

W127926E02
1.167,1.958 1.833,2.313 true 1.271,2.75 1.885,3.063 true 1.906,3.354 1.719,3.49 true 1.938,2.729 2.604,2.375 true 5.542,2.073 5.854,1.531 true 5.563,2.469 5.854,2.854 true 1.01,1.823 1.396,2.063 0.385,0.24 10 false *1 1.563,3.49 1.844,3.708 0.281,0.219 10 false *3 1.063,2.552 1.448,2.792 0.385,0.24 10 false *2 2.625,2.26 3.01,2.5 0.385,0.24 10 false *4 5.823,1.375 6.208,1.615 0.385,0.24 10 false *5 5.844,2.854 6.229,3.094 0.385,0.24 10 false *6

Text in Illustration
*1 Solenoid *2 Nozzle Needle
*3 Low Suck Volume Nozzle *4 Control Plate
*5 Injector Compensation Value *6 QR Code



d.

Fuel Filter

i.

A cartridge type fuel filter assembly is used.


ii.

A paper filter element that offers high filtering efficiency and captures the particles is used.


iii.

A fuel filter warning switch is provided in the fuel filter assembly.

W123717E03
2.552,2.146 3.125,1.938 true 4.354,2.896 3.698,2.594 true 2.385,0.573 3.063,0.958 true 2.385,2.104 2.625,2.344 0.24,0.24 10 false *2 4.385,2.875 4.625,3.115 0.24,0.24 10 false *3 2.24,0.427 2.479,0.667 0.24,0.24 10 false *1

Text in Illustration
*1 Fuel Filter Warning Switch (Vacuum Switch) *2 Fuel Filter Element
*3 Fuel Sedimenter Level Warning Switch - -



e.

Fuel Tank

i.

A dual fuel tank is used.*

*: Models with dual fuel tank





OPERATION


a.

Supply Pump

i.

When the cam rotates the roller is pushed up, and in turn the plunger is pushed upward as well. When the plunger is not pushed up by the cam, it is pushed back down by the spring.

W123656E02
0.708,0.25 0.802,0.656 true 1.563,1.479 2.229,1.323 true 1.563,1.865 2.021,1.771 true 1.573,2.594 2.146,2.458 true 1.563,3.177 2.021,3.063 true 1.573,2.24 2.01,2.219 true 1.406,1.396 1.729,1.667 0.323,0.271 10 false *2 0.552,0.083 0.875,0.354 0.323,0.271 10 false *1 1.396,1.823 1.719,2.094 0.323,0.271 10 false *3 1.406,2.167 1.729,2.438 0.323,0.271 10 false *4 1.396,2.563 1.719,2.833 0.323,0.271 10 false *5 1.396,3.135 1.719,3.406 0.323,0.271 10 false *6

Text in Illustration
*1 Pre-stroke Control Valve *2 Plunger
*3 Spring *4 Shoe
*5 Roller *6 Double Cam


ii.

The ECM controls the closing timing of the pre-stroke control valve while the plunger is moving up in order to adjust the fuel supply volume. As a result, the fuel pressure in the common rail assembly is controlled to the target injection pressure.


iii.

When the pre-stroke control valve is closed while the plunger is moving up, the fuel pressure increases. When the fuel pressure exceeds the common-rail pressure, fuel is supplied to the common rail assembly.


iv.

When the closing timing of the pre-stroke control valve is delayed, the length of pressure-fed strokes will decrease, as well as the fuel discharge volume.

W123658E01
3.328,0.076 3.632,0.369 0.303,0.293 10 *a 3.3,0.552 3.389,0.242 false

Text in Illustration
*a Return Fuel - -


v.

When the closing timing of the pre-stroke control valve is hastened, the length of pressure-fed strokes will increase, as well as the fuel discharge volume.


vi.

When the pre-stroke control valve is closed while the plunger is moving up, the fuel pressure increases. When the fuel pressure exceeds the common-rail pressure, fuel is supplied to the common rail assembly.

W123657



b.

Injector

i.

Current flows through the solenoid coil and the valve is pulled up.


ii.

Fuel flows out from the orifice (out) in the control chamber.


iii.

The fuel pressure in the control chamber drops.


iv.

The nozzle needle moves up due to the differential pressure above and below the nozzle needle.


v.

Fuel is injected through the nozzle.


vi.

Current through the solenoid coil is stopped and the control valve is closed.


vii.

Fuel flows into the control chamber through the orifice (in) and the control plate moves down.


viii.

The pressure in the control chamber increases causing the force acting above and below the nozzle needle to reverse due to the fuel pressure.


ix.

The nozzle needle moves down and closes to stop injection.


x.

When the control chamber pressure equalize, the control plate rises due to the force of the spring.

W123659E02
1.094,1.385 0.51,0.854 true 1.292,1.927 0.552,1.979 true 1.406,1.865 0.542,1.406 true 1.531,2.042 2.031,2.167 true 1.615,1.698 2.073,1.333 true 0.354,0.729 0.708,1.031 0.354,0.302 10 false *1 0.375,1.281 0.729,1.583 0.354,0.302 10 false *2 0.365,1.917 0.719,2.219 0.354,0.302 10 false *3 2.073,1.208 2.427,1.51 0.354,0.302 10 false *4 1.344,3.313 1.698,3.615 0.354,0.302 10 false *a 3.531,3.313 3.885,3.615 0.354,0.302 10 false *b 5.708,3.313 6.063,3.615 0.354,0.302 10 false *c 2.094,2.135 2.448,2.438 0.354,0.302 10 false *5

Text in Illustration
*1 Control Valve *2 Out-orifice
*3 Control Plate *4 In-orifice
*5 Control Chamber - -
*a Before fuel injection *b Fuel injection
*c After fuel injection - -
V100144

High Fuel Pressure
V100145

Low Fuel Pressure



c.

Fuel Filter

i.

When the water in the sedimenter section reaches a certain amount, the fuel sedimenter level warning switch comes on, the warning light in the combination meter assembly blinks the multi buzzer sounds.*1


ii.

When the water in the sedimenter section reaches a certain amount, the fuel sedimenter level warning switch comes on, the multi-information display in the combination meter assembly displays, the master warning light in the combination meter assembly illuminates and the multi buzzer sounds. For details, see the METER / GAUGE / DISPLAY section.*2


iii.

A fuel filter warning switch, which turns on or off when the internal vacuum of the filter increases, is provided in the fuel filter. This switch, which turns off when the internal vacuum of the fuel filter increases to a predetermined level, is connected by wire to the combination meter assembly.

W104524E03
4.823,2.302 5.094,2.031 5.094,2.031 5.25,2.031 true 0.625,0.417 1.24,0.667 0.615,0.25 10 false Fuel Tank 5.281,1.948 6.615,2.24 1.333,0.292 10 false Fuel Filter Assembly 5.792,3.75 6.25,4.052 0.458,0.302 10 false : Fuel 5.792,4.083 6.844,4.385 1.052,0.302 10 false : Electric signal 2.208,2.156 3.094,2.427 0.885,0.271 10 false Fuel Element 0.698,2.865 2.073,3.333 1.375,0.469 10 false Fuel Sedimenter Level Warning Switch 3.083,2.875 4.74,3.333 1.656,0.458 10 false Fuel Filter Warning Switch (Vacuum Switch) 3.208,0.417 4.75,0.667 1.542,0.25 10 false Supply Pump Assembly 1.719,4.271 3.615,4.594 1.896,0.323 10 false Combination Meter Assembly 5.375,1.219 6.5,1.521 1.125,0.302 10 false Injector Assembly 5.198,0.417 6.677,0.719 1.479,0.302 10 false Common-rail Assembly


iv.

When the combination meter assembly detects that the internal vacuum of the fuel filter has increased (by way of the fuel filter warning switch off signal), it determines that the fuel filter has become clogged. Then, it illuminates the fuel system warning light on the combination meter assembly to urge the driver to replace the fuel filter.*1


v.

When the combination meter assembly detects that the internal vacuum of the fuel filter has increased (by way of the fuel filter warning switch off signal), it determines that the fuel filter has become clogged. Then, it displays the multi-information display on the combination meter assembly to urge the driver to replace the fuel filter. For details, see the METER / GAUGE / DISPLAY section.*2

W128966E02
0.938,1.042 1.198,1.042 true 2.302,2.396 2.552,2.396 false 1.354,0.979 1.354,0.396 1.354,0.396 1.5,0.396 true 2.917,1.688 3.073,0.646 3.073,0.646 3.125,0.646 true 2.76,1.906 2.573,1.844 2.573,1.844 1.833,1.844 true 1.406,2.802 1.115,2.948 true 6.021,2.354 6.021,2.635 true 0.917,4.958 1.042,4.958 true 2.302,6.531 2.552,6.531 false 2.917,5.833 3.073,4.792 3.073,4.792 3.125,4.792 false 2.75,6.042 2.5,6.01 2.5,6.01 1.792,6.01 true 1.417,6.729 1.281,6.781 false 6.031,6.396 6.031,6.677 true 2.302,6.729 2.5,6.729 true 2.302,2.594 2.5,2.594 true 1.948,1.031 2.677,1.354 0.729,0.323 10 false Meter ECU 0.156,0.958 0.979,2.083 0.823,1.125 10 false Combination Meter Assembly 1.135,1.76 1.865,2.104 0.729,0.344 10 false Diaphragm 0.167,2.167 0.833,2.802 0.667,0.635 10 false From Fuel Tank 3.323,2.333 3.771,3.323 0.448,0.99 10 false To Supply Pump 2.573,2.51 3.135,3.125 0.563,0.615 10 false Filter Element 0.792,2.885 1.198,3.271 0.406,0.385 10 false Fuel Filter 1.281,3.156 2.844,3.458 1.563,0.302 10 false - Normal Fuel Filter - 4.26,3.146 5.865,3.448 1.604,0.302 10 false - Fuel Filter Clogged Up - 1.552,0.302 3.313,0.677 1.76,0.375 10 false Fuel System Warning Light 0.052,0 4.854,0.375 4.802,0.375 12 false Models with Analog Display Type Combination Meter Assembly 3.188,0.573 4.24,1.365 1.052,0.792 10 false Fuel Filter Warning Switch 5.073,1.073 5.802,1.396 0.729,0.323 10 false Meter ECU 5.646,2.688 6.844,3.333 1.198,0.646 10 false Negative Pressure (Vacuum) 0.104,4.875 0.927,6 0.823,1.125 10 false Combination Meter Assembly 1.104,5.917 1.833,6.26 0.729,0.344 10 false Diaphragm 0.115,6.302 0.74,6.938 0.625,0.635 10 false From Fuel Tank 3.344,6.49 3.792,7.479 0.448,0.99 10 false To Supply Pump 2.531,6.656 3.094,7.271 0.563,0.615 10 false Filter Element 0.979,6.698 1.313,7.042 0.333,0.344 10 false Fuel Filter 1.25,7.271 2.813,7.573 1.563,0.302 10 false - Normal Fuel Filter - 4.26,7.271 5.865,7.573 1.604,0.302 10 false - Fuel Filter Clogged Up - 0.063,3.76 5.052,4.135 4.99,0.375 12 false Models with Optitron Display Type Combination Meter Assembly 3.156,4.708 4.115,5.479 0.958,0.771 10 false Fuel Filter Warning Switch 4.313,4.479 6.021,4.885 1.708,0.406 10 false Multi-information Display 4.708,5.167 5.438,5.49 0.729,0.323 10 false Meter ECU 1.198,4.49 2.906,4.896 1.708,0.406 10 false Multi-information Display 1.625,5.156 2.354,5.479 0.729,0.323 10 false Meter ECU 5.625,6.719 6.823,7.365 1.198,0.646 10 false Negative Pressure (Vacuum)

*1: Models with analog display type combination meter assembly

*2: Models with Optitron display type combination meter assembly




d.

Fuel Tank

i.

On the models with dual fuel tank, a fuel pump and jet pump are provided in the main fuel tank to transfer the fuel from sub fuel tank to main fuel tank. This is accomplished by utilizing the fuel flow through the jet pump. The pressure difference is created by the fuel as it passes through the venturi, and it is used to suck the fuel out of the sub fuel tank and send it to the main fuel tank.

W127968E02
1.135,1.604 1.583,1.604 true 2.094,1.646 2.25,1.813 2.25,1.813 2.51,1.813 true 1.896,0.344 2.063,0.188 2.063,0.188 2.188,0.188 false 1.885,1.927 1.885,2.031 false 3.646,1.917 3.646,2.021 false 4.667,0.656 4.323,0.313 4.323,0.313 4.188,0.313 false 0.927,1.552 1.135,1.74 0.208,0.188 10 false *1 2.552,1.75 2.76,1.938 0.208,0.188 10 false *2 3.979,0.26 4.188,0.448 0.208,0.188 10 false *2 4.781,0.219 4.99,0.406 0.208,0.188 10 false *a 5.865,1.323 6.073,1.51 0.208,0.188 10 false *b 4.802,1.896 5.01,2.083 0.208,0.188 10 false *c 1.792,2.031 2,2.219 0.208,0.188 10 false *4 3.552,2.135 3.76,2.323 0.208,0.188 10 false *5 2.208,0.104 2.417,0.292 0.208,0.188 10 false *3

Text in Illustration
*1 Fuel Pump Assembly *2 Jet Pump
*3 Fuel Pump Filter Assembly *4 Main Fuel Tank
*5 Sub Fuel Tank - -
*a From Fuel Pump *b From Sub Fuel Tank
*c To Main Fuel Tank - -