Home › Engine / Hybrid System › 2TR-FE (EMISSION CONTROL) › EMISSION CONTROL SYSTEM
NM27T0E _51 Engine / Hybrid System _053586 2TR-FE EMISSION CONTROL _0260111 EMISSION CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

2TR-FE EMISSION CONTROL  EMISSION CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the emission control system are as follows:

Component Function
Exhaust Emission System ECM Determines an optimal fuel injection volume based on the signals from various sensors.
TWC Reduces CO, HC and NOx in the exhaust gas.
Oxygen Sensor Detects the oxygen concentration in the exhaust emissions by measuring the electromotive force generated in the sensor itself. For details, see the 2TR-FE ENGINE CONTROL section.
Air Fuel Ratio Sensor
Air Injection System Air Pump Assembly Uses a built-in DC motor to supply air to the air injection control valve.
Air Injection Control Valve Introduces air that is pumped by the electric air pump into the exhaust manifold.
Air Injection Control Driver
·

Activated by the ECM, the air injection driver actuates the electric air pump and the air injection control valve.

·

Detects an input-output circuit failure at the air injection driver and transmits it to the ECM.


Air Pressure Sensor This sensor uses built-in semiconductors to detect the pressure inside the air switching valve.
ECM
·

Controls the air injection system in accordance with signals from the crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and air pressure sensor.

·

Receives a failure detection signal from the air injection driver and stores a corresponding DTC in memory.


Evaporative Emission Control ECM Sends signals to the VSV (for EVAP) to control the purge flow.
Charcoal Canister Sub-assembly Contains activated charcoal to absorb the fuel vapor created in the fuel tank.
VSV (for EVAP) Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister into the intake manifold.



FUNCTION


a.

Air Injection System

i.

To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.


ii.

This system consists of an air pump assembly, an air injection control valve, and an air injection control driver.


iii.

The ECM estimates the amount of air injected to the TWCs based on signals from the mass air flow meter in order to regulate the air injection time.




CONSTRUCTION


a.

Three-Way Catalytic converter (TWC)

i.

TWCs are provided in the exhaust manifold and front exhaust pipe.


ii.

This TWC enables improved exhaust emissions by optimizing the cell density and the wall thickness.

W102479E02
3.302,1.406 3.302,0.479 3.302,0.479 4.844,0.479 true 4.5,1.104 4.5,0.479 true 4.875,0.375 5.094,0.635 0.219,0.26 10 false *1

Text in Illustration
*1 TWC - -



b.

Air Pump Assembly

i.

An air pump assembly consists of a DC motor, an impeller and an air filter.


ii.

DC motor operation is controlled by the ECM via an air injection control driver. The motor supplies air into an air injection control valve through the impeller.


iii.

On the models for compliant with EURO5 emission regulations, a heater is provided to prevent operation faults in cold conditions.

W127705E01
3.802,0.49 6.688,3.417 2.885,2.927 2.24,0.458 2.927,0.156 2.927,0.156 3.219,0.156 true 2.125,2.813 2.729,3.323 2.729,3.323 3.073,3.323 true 4.021,0.604 4.333,0.802 0.313,0.198 10 false *a 3.26,0.052 3.896,0.354 0.635,0.302 10 false *1 (*A) 3.135,3.208 3.771,3.51 0.635,0.302 10 false *2 (*A)

Text in Illustration
*A Models for compliant with EURO5 emission regulations - -
*1 Air Pump Cover *2 Heater
*a Cross Section - -



c.

Air Switching Valve Assembly

i.

An Air Switching Valve Assembly switches the air flow and a reed valve that restricts the exhaust flow to one direction.


ii.

The air switching valve is a solenoid valve that is actuated by the air injection control driver.


iii.

When the air switching valve turns on, an air injection pipe, which is provided in the exhaust manifold, directs the air from the air pump assembly to the exhaust port.

W127099E03
1.76,0.969 0.906,0.396 true 1.844,1.458 0.583,1.281 true 2.156,1.802 2.688,2.365 true 5.177,1.74 4.833,2.219 true 5.219,1.604 4.5,1.344 true 0.74,0.25 0.958,0.51 0.219,0.26 10 false *1 0.375,1.156 0.594,1.417 0.219,0.26 10 false *2 2.677,2.344 2.896,2.604 0.219,0.26 10 false *3 4.677,2.188 4.896,2.448 0.219,0.26 10 false *5 5.281,2.26 5.5,2.521 0.219,0.26 10 false *a 4.323,1.219 4.542,1.479 0.219,0.26 10 false *4

Text in Illustration
*1 Air Switching Valve Assembly *2 Air Injection Pipe
*3 Exhaust Manifold *4 Air Switching Valve
*5 Reed Valve - -
*a Air Injection Control Valve Cross Section - -
V100135

From Air Pump Assembly
V100136

To Air Injection Pipe



d.

Air Pressure Sensor

i.

The air pressure sensor consists of a semiconductor which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure inside the air switching valve into an electrical signal, and sends it to the ECM in an amplified form.

W105124E02
1.177,1.188 1.177,0.24 1.177,0.24 0.979,0.24 true 0.198,0.125 1.021,0.5 0.823,0.375 10 false Sensor Unit 4.188,2.031 4.323,2.24 0.135,0.208 10 false 0 3.677,1.094 4.198,1.948 0.521,0.854 10 false Output Voltage 4.552,2.042 5.948,2.76 1.396,0.719 10 false Pressure inside the air switching valve 6.021,2.042 6.49,2.396 0.469,0.354 10 false (kPa) 4.073,0.521 4.323,0.792 0.25,0.271 10 false (V) 4.313,0.26 6.198,0.615 1.885,0.354 10 false - Sensor Characteristic -




OPERATION


a.

Air Injection Control Driver

i.

A semiconductor type air injection control driver is used. Activated by the ECM, this driver actuates the air pump assembly and the air injection control valve.


ii.

The air injection control driver also detects failures in the input and output circuits of the air injection driver and transmits the failure status to the ECM via duty cycle signals.

W102399E06
2.156,0.865 3.438,1.26 1.281,0.396 10 false Air Pump Assembly Actuation Request 1.719,1.802 3.917,2.479 2.198,0.677 10 false Air Injection Control Valve Actuation Request 2.313,3.198 3.49,3.479 1.177,0.281 10 false Duty Cycle Signal 1.719,0.573 2.177,0.781 0.458,0.208 10 false AIRP 3.677,0.542 3.969,0.75 0.292,0.208 10 false SIP 3.698,1.521 3.99,1.729 0.292,0.208 10 false SIV 3.792,2.521 4.042,2.74 0.25,0.219 10 false DI 1.729,2.5 2.146,2.729 0.417,0.229 10 false AIDI 1.74,1.594 2.115,1.792 0.375,0.198 10 false AIRV 1.052,1.604 1.583,2.052 0.531,0.448 10 false ECM 4.094,1.219 4.823,2.375 0.729,1.156 10 false Air Injection Control Driver 5.01,1.073 5.281,1.281 0.271,0.208 10 false VP 5.083,1.427 6.406,1.833 1.323,0.406 10 false Air Pump Assembly 5.24,2.583 6.188,3.458 0.948,0.875 10 false Air Injection Control Valve 5.01,2 5.281,2.208 0.271,0.208 10 false VV

DI Terminal Output
Condition AIRP AIRV Output (Duty Cycle Signal)
Open circuit in line between AIDI and DI terminals. - -
W132975E01
0.438,1.479 0.896,1.677 0.458,0.198 10 false GND

Failure in line between ECM terminals and air injection control driver. - -
W132975E01
0.438,1.479 0.896,1.677 0.458,0.198 10 false GND

Output failure at air injection control driver. (Failure in air pump assembly actuation circuit) - -
W132977E01
0.438,1.5 0.896,1.698 0.458,0.198 10 false GND 1.396,0.938 2.042,1.115 0.646,0.177 10 false 200 ms 2.646,1 3.375,1.188 0.729,0.188 10 false Duty 20%

Output failure at air injection control driver. (Failure in air injection control valve actuation circuit) - -
W132978E01
2.688,1.01 3.375,1.208 0.688,0.198 10 false Duty 40% 0.438,1.51 1.125,1.708 0.688,0.198 10 false GND

Failure of air injection control driver caused by overheating. - -
W132979E01
0.417,1.521 0.875,1.719 0.458,0.198 10 false GND 2.646,1.052 3.385,1.26 0.74,0.208 10 false Duty 60%

Normal On On
W132980E01
0.438,1.521 0.896,1.719 0.458,0.198 10 false GND 2.646,0.969 3.427,1.198 0.781,0.229 10 false Duty 80%

Off Off
W132976E01
0.375,1.49 0.833,1.688 0.458,0.198 10 false GND

On Off
Off On



b.

Evaporative Emission Control System

i.

Based on the signals from various sensors, the ECM opens and closes the VSV (for EVAP). Thus, it controls the purge flow of evaporative emissions (HC) in the charcoal canister sub-assembly in accordance with the engine conditions.