Home › Engine / Hybrid System › 1GR-FE EMISSION CONTROL › EMISSION CONTROL SYSTEM
NM27T0E _51 Engine / Hybrid System _053587 1GR-FE EMISSION CONTROL _0260112 EMISSION CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

1GR-FE EMISSION CONTROL  EMISSION CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the emission control system are as follows:

Component Function
Exhaust Emission System ECM Determines an optimal fuel injection volume based on the signals from various sensors.
TWC Reduces CO, HC and NOx in the exhaust gas.
Oxygen Sensor Detects the oxygen concentration in the exhaust emissions by measuring the electromotive force generated in the sensor itself. For details, see the 1GR-FE Engine Control.
Air Fuel Ratio Sensor
Air Injection System* Air Pump Assembly Uses a built-in DC motor to supply air to the air injection control valve.
Air Injection Control Valve Introduces air that is pumped by the electric air pump into the exhaust manifold.
Air Injection Control Driver
·

Activated by the ECM, the air injection control driver actuates the air pump assembly and the air injection control valve.

·

Detects an input-output circuit failure at the air injection driver and transmits it to the ECM.


ECM
·

Controls the air injection system in accordance with signals from the crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and air pressure sensor.

·

Receives a failure detection signal from the air injection driver and stores a corresponding DTC in memory.


Evaporative Emission Control ECM Sends signals to the VSV (for EVAP) to control the purge flow.
Charcoal Canister Sub-assembly Contains activated charcoal to absorb the fuel vapor created in the fuel tank.
VSV (for EVAP) Opens in accordance with the signals from the ECM when the system is purging, in order to send the fuel vapor that was absorbed by the charcoal canister sub-assembly into the intake manifold.

*: Models for compliant with EURO 5 and EURO 6 emission regulations




FUNCTION


a.

Air Injection System (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.


ii.

This system is comprised of an air injection control driver, an air pump assembly, and 2 air injection control valves with built-in air pressure sensors.


iii.

The air injection control valves provided on each bank are controlled independently by the ECM and the air injection control driver.


iv.

The ECM estimates the amount of air injected to the TWCs based on signals from the mass air flow meter in order to regulate the air injection time.




CONSTRUCTION


a.

Three-Way Catalytic converter (TWC)

i.

TWCs are provided in the exhaust manifold of each bank and also in the exhaust center pipe.


ii.

An exhaust manifold with an integrated TWC is used for warm-up of the TWC.


iii.

An ultra thin-wall, high-cell density, ceramic type TWC is used for the exhaust manifold and a thin-wall, ceramic type TWC is used for the exhaust center pipe.


iv.

This TWC enables improved exhaust emissions by optimizing the cell density and the wall thickness.

W102397E03
3.031,1.26 3.271,0.625 3.271,0.625 4.969,0.625 true 3.875,0.625 3.583,1.375 true 4.063,0.625 3.646,1.677 true 4.719,0.625 4.229,1.865 true 5.01,0.531 5.208,0.74 0.198,0.208 10 false *1

Text in Illustration
*1 TWC - -



b.

Air Pump Assembly (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

An air pump assembly consists of a DC motor, an impeller, an air filter and a heater.


ii.

The DC motor is controlled by the air injection driver in accordance with signals from the ECM. The motor supplies air into an air injection control valve through the impeller.


iii.

A heater is provided to prevent operation faults in cold conditions.

W100657E02
3.677,0.25 5.875,2.521 2.198,2.271 4.219,1.323 4.073,1.146 4.073,1.146 3.99,1.146 true 4.385,1.167 4.188,0.792 4.188,0.792 4.073,0.792 true 5.083,1.917 5.438,1.677 5.438,1.677 5.531,1.677 true 3.813,1.063 4.021,1.302 0.208,0.24 10 false *2 3.906,0.698 4.115,0.938 0.208,0.24 10 false *1 5.563,1.594 5.771,1.833 0.208,0.24 10 false *3 3.833,0.323 4.042,0.563 0.208,0.24 10 false *a

Text in Illustration
*1 Impeller *2 Heater
*3 DC Motor - -
*a Cross Section - -
V100135

To Air Injection Control Valve
V100136

From Air Inlet



c.

Air Injection Control Valve (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

An air injection control valve consists of an air switching valve that switches the air flow and a reed valve that restricts the exhaust flow to one direction.


ii.

The air switching valve is a solenoid valve that is actuated by the ECM and air injection control driver.


iii.

An air pressure sensor is built into the corresponding air injection control valve.


iv.

The air injection control valves for bank 1 and bank 2 have the same basic structure and function.

W102331E02
4.438,0.521 6.948,3 2.51,2.479 1.26,0.833 1.406,0.396 1.406,0.396 1.646,0.396 true 3.094,1.875 3.469,0.969 3.469,0.969 3.708,0.969 true 6.073,2.01 5.438,1.573 5.438,1.573 5.271,1.573 true 6.125,1.292 6.219,0.771 6.219,0.771 6.417,0.771 true 1.688,0.292 1.896,0.5 0.208,0.208 10 false *1 3.76,0.885 3.969,1.094 0.208,0.208 10 false *2 4.573,0.635 4.781,0.844 0.208,0.208 10 false *a 5.094,1.49 5.302,1.698 0.208,0.208 10 false *3 6.469,0.698 6.677,0.906 0.208,0.208 10 false *4

Text in Illustration
*1 Air Injection Control Valve (Bank 1) *2 Air Injection Control Valve (Bank 2)
*3 Air Switching Valve *4 Air Pressure Sensor
*a Air Injection Control Valve (Bank 1) Cross Section - -
V100135

From Air Pump Assembly
V100136

To Air Injection Pipe



d.

Air Pressure Sensor (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

The air pressure sensor consists of a semiconductor, which has a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.


ii.

The air pressure sensors for bank 1 and bank 2 have the same basic structure and function.

W102332E03
0.802,1.958 0.885,0.365 0.885,0.365 1.083,0.365 true 2.135,1.271 2.375,0.844 2.375,0.844 2.583,0.844 true 1.135,0.292 2.688,0.875 1.552,0.583 10 false Air Pressure of Air Pump Assembly 2.646,0.771 3.479,1.125 0.833,0.354 10 false Sensor Unit 3.625,1.49 4.104,1.917 0.479,0.427 10 false Output Voltage 3.875,1.177 4.125,1.417 0.25,0.24 10 false 4.5 3.875,2.135 4.125,2.375 0.25,0.24 10 false 0.5 4.427,2.813 4.677,3.052 0.25,0.24 10 false 45 6.063,2.792 6.406,3.031 0.344,0.24 10 false 150 6.448,2.781 6.917,3.021 0.469,0.24 10 false (kPa) 3.885,0.875 4.146,1.115 0.26,0.24 10 false (V) 4.75,2.948 6.021,3.781 1.271,0.833 10 false Air Pressure (Absolute Pressure)




OPERATION


a.

Air Pressure Sensor (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

The ECM detects operation of the air injection system based on signals from the air pressure sensor as follows:

1.

When the air pump assembly is on and the air injection control valve is closed, the pressure is stable.

2.

When the air pump assembly is on and the air injection control valve is open, the pressure drops slightly and becomes unstable because of exhaust pulses.

3.

When the air pump assembly is off and the air injection control valve is closed, the pressure remains at atmospheric pressure.

4.

When the air pump assembly is off and the air injection control valve is open, the pressure drops below atmospheric pressure and becomes unstable because of exhaust pulses.


W102398E07
1.135,1 1.792,1.24 0.656,0.24 10 false Pressure 0.917,2.083 1.802,2.615 0.885,0.531 10 false (Atmospheric Pressure) 1.688,1.906 1.813,2.146 0.125,0.24 10 false 0 3.219,1.917 3.573,2.208 0.354,0.292 10 false Time 0.396,0.656 1.135,0.979 0.74,0.323 10 false Example: 1 4.24,0.99 4.896,1.229 0.656,0.24 10 false Pressure 4.021,2.146 4.906,2.677 0.885,0.531 10 false (Atmospheric Pressure) 4.792,1.917 4.917,2.156 0.125,0.24 10 false 0 6.323,1.906 6.677,2.198 0.354,0.292 10 false Time 3.49,0.667 4.229,0.99 0.74,0.323 10 false Example: 2 1.917,2.198 3.604,2.573 1.688,0.375 10 false Air Pump Assembly: On 1.917,2.594 3.198,3.219 1.281,0.625 10 false Air Injection Control Valve: Closed 1.135,3.75 1.792,3.99 0.656,0.24 10 false Pressure 0.896,4.969 1.781,5.5 0.885,0.531 10 false (Atmospheric Pressure) 1.688,4.688 1.813,4.927 0.125,0.24 10 false 0 3.219,4.688 3.573,4.979 0.354,0.292 10 false Time 0.396,3.354 1.135,3.677 0.74,0.323 10 false Example: 3 1.917,5.052 3.615,5.427 1.698,0.375 10 false Air Pump Assembly: Off 1.917,5.458 3.198,6.083 1.281,0.625 10 false Air Injection Control Valve: Closed 4.219,3.75 4.875,3.99 0.656,0.24 10 false Pressure 3.979,4.938 4.865,5.469 0.885,0.531 10 false (Atmospheric Pressure) 4.771,4.698 4.896,4.938 0.125,0.24 10 false 0 6.302,4.688 6.656,4.979 0.354,0.292 10 false Time 3.479,3.385 4.219,3.708 0.74,0.323 10 false Example: 4 5,5.104 6.698,5.427 1.698,0.323 10 false Air Pump Assembly: Off 5,5.479 6.281,6.104 1.281,0.625 10 false Air Injection Control Valve: Open 4.969,2.25 6.729,2.625 1.76,0.375 10 false Air Pump Assembly: On 4.969,2.656 6.25,3.281 1.281,0.625 10 false Air Injection Control Valve: Open



b.

Air Injection Control Driver (Models for Compliant with EURO 5 and EURO 6 Emission Regulations)

i.

A semiconductor type air injection control driver is used. Activated by the ECM, this driver actuates the air pump assembly and the air injection control valve.


ii.

The air injection control driver also detects failures in the input and output circuits of the air injection driver and transmits the failure status to the ECM via duty cycle signals.

W102399E06
2.156,0.865 3.438,1.26 1.281,0.396 10 false Air Pump Assembly Actuation Request 1.719,1.802 3.917,2.479 2.198,0.677 10 false Air Injection Control Valve Actuation Request 2.313,3.198 3.49,3.479 1.177,0.281 10 false Duty Cycle Signal 1.719,0.573 2.177,0.781 0.458,0.208 10 false AIRP 3.677,0.542 3.969,0.75 0.292,0.208 10 false SIP 3.698,1.521 3.99,1.729 0.292,0.208 10 false SIV 3.792,2.521 4.042,2.74 0.25,0.219 10 false DI 1.729,2.5 2.146,2.729 0.417,0.229 10 false AIDI 1.74,1.594 2.115,1.792 0.375,0.198 10 false AIRV 1.052,1.604 1.583,2.052 0.531,0.448 10 false ECM 4.094,1.219 4.823,2.375 0.729,1.156 10 false Air Injection Control Driver 5.01,1.073 5.281,1.281 0.271,0.208 10 false VP 5.083,1.427 6.406,1.833 1.323,0.406 10 false Air Pump Assembly 5.24,2.583 6.188,3.458 0.948,0.875 10 false Air Injection Control Valve 5.01,2 5.281,2.208 0.271,0.208 10 false VV

DI Terminal Output
Condition AIRP AIRV Output (Duty Cycle Signal)
Open circuit in line between AIDI and DI terminals. - -
W132975E01
0.438,1.479 0.896,1.677 0.458,0.198 10 false GND

Failure in line between ECM terminals and air injection control driver. - -
W132975E01
0.438,1.479 0.896,1.677 0.458,0.198 10 false GND

Output failure at air injection control driver. (Failure in air pump assembly actuation circuit) - -
W132977E01
0.438,1.5 0.896,1.698 0.458,0.198 10 false GND 1.396,0.938 2.042,1.115 0.646,0.177 10 false 200 ms 2.646,1 3.375,1.188 0.729,0.188 10 false Duty 20%

Output failure at air injection control driver. (Failure in air injection control valve actuation circuit) - -
W132978E01
2.688,1.01 3.375,1.208 0.688,0.198 10 false Duty 40% 0.438,1.51 1.125,1.708 0.688,0.198 10 false GND

Overheat failure of air injection control driver. - -
W132979E01
0.417,1.521 0.875,1.719 0.458,0.198 10 false GND 2.646,1.052 3.385,1.26 0.74,0.208 10 false Duty 60%

Normal On On
W132980E01
0.438,1.521 0.896,1.719 0.458,0.198 10 false GND 2.646,0.969 3.427,1.198 0.781,0.229 10 false Duty 80%

Off Off
W132976E01
0.375,1.49 0.833,1.688 0.458,0.198 10 false GND

On Off
Off On



c.

Evaporative Emission Control System

i.

Based on the signals from various sensors, the ECM opens and closes the VSV (for EVAP). Thus, it controls the purge flow of evaporative emissions (HC) in the charcoal canister sub-assembly in accordance with the engine conditions.