Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2015.06–2016.08
NM27T0E _59 Vehicle Exterior _053645 WINDOW / GLASS _0260197 POWER WINDOW CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The power window control system has the following functions:

Function Outline
Manual Up-and-down The manual up-and-down function causes the window to open or close while the multiplex network master switch assembly or power window regulator switch assembly is being pulled halfway up or pushed halfway down. The window stops as soon as the switch is released.
One-touch Auto Up-and-down The one-touch auto up-and-down function enables the window to be fully opened or closed at a touch of the multiplex network master switch assembly or power window regulator switch assembly.
Jam Protection The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during one-touch auto-up operation or manual up operation.
Catch Protection The catch protection function automatically stops the power window if a foreign object gets caught in the window during a down operation.
Soft Stop During an up or down operation of the power window, the power window ECU stops the current to the power window motor right before the door glass is fully closed or opened.
Remote Control The multiplex network master switch assembly can control the up-and-down operation of all door windows.
Window Lock Operation of the passenger windows is disabled when the window lock switch is pressed.
Key Off Operation The key off operation function makes it possible to operate the power windows for approximately 43 seconds after the ignition switch (engine switch*1) is turned off, if either front door is not opened.
Key-linked Up-and-down*2, *3 When the driver door is locked, and the transmitter in the driver door is turned and maintained in the lock direction for 1.5 seconds or more, the main body ECU activates the power window motors to raise all door windows while the key is turned. Similarly, when the driver door is unlocked, turning and maintaining the driver door key in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered.
Transmitter-linked Up-and-down*2, *3
·

When the door control receives an unlock signal from the transmitter for longer than 2.5 seconds, the main body ECU controls the power window motors in accordance with the signal to open the windows.

·

When the door control receives a lock signal from the transmitter for longer than 2.5 seconds, the main body ECU controls the power window motors in accordance with the signal to close the windows.



HINT:

*1: Models with entry and start system

*2: Customizable parameters can be configured by means of the customized body electronics system (default setting: off). For details, refer to the Repair Manual.

*3: The key is not detected within the interior detection area on models with entry and start system.



i.

The ECU which is built into each power window motor stores the initial position of its door window. The initial position is not cleared even if battery terminals, fuses or the power window motor connector is disconnected. However, after removing or reinstalling window components, or replacing the power window regulator sub-assembly or power window regulator motor, the stored initial position data must be cleared and initialization must be performed. For details, refer to the Repair Manual.



b.

Jam Protection Function

i.

The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window during one-touch auto up operation or manual up operation.


ii.

Even when the power window regulator switch assembly is maintained in the auto up position, the power window operates in reverse if a jam is detected.


iii.

In the case of manual up operation using the power window regulator switch assembly, the power window is moved downward by approximately 30 mm (1.2 in.) or for approximately 5 seconds. In the case of up operation except for manual up operation using the power window regulator switch assembly, the power window is moved downward by approximately 125 mm (4.9 in.) or for approximately 5 seconds.


iv.

The power window ECU determines if a foreign object gets jammed according to changes in the output signal from the pulse sensor (Hall IC). Both of the following 2 judgment methods are used:

U170792E02
2.385,1.49 2.635,1.49 false 2.635,1.49 2.635,1.104 false 2.635,1.104 2.885,1.104 false 2.885,1.49 2.885,1.104 false 2.885,1.49 3.135,1.49 false 3.135,1.49 3.135,1.104 false 3.135,1.104 3.385,1.104 false 3.385,1.49 3.385,1.104 false 3.385,1.49 3.635,1.49 false 3.635,1.49 3.635,1.104 false 3.635,1.104 3.885,1.104 false 3.885,1.49 3.885,1.104 false 3.885,1.49 4.135,1.49 false 4.135,1.49 4.135,1.104 false 2.51,2.115 2.76,2.115 false 2.76,2.115 2.76,1.74 false 2.76,1.74 3.01,1.74 false 3.01,2.115 3.01,1.74 false 3.01,2.115 3.26,2.115 false 3.26,2.115 3.26,1.74 false 3.26,1.74 3.51,1.74 false 3.51,2.115 3.51,1.74 false 3.51,2.115 3.76,2.115 false 3.76,2.115 3.76,1.74 false 3.76,1.74 4.01,1.74 false 4.01,2.115 4.01,1.74 false 4.01,2.115 4.896,2.115 false 4.135,1.104 4.896,1.104 false 2.51,2.115 2.51,1.74 false 2.375,1.74 2.51,1.74 false 0.885,1.177 1.844,1.531 0.958,0.354 10 false Pulse Signal 1 0.073,0.042 2.521,0.219 2.448,0.177 10 false Judgment Method (Overload Detection) 0.917,1.813 1.906,2.26 0.99,0.448 10 false Pulse Signal 2 4.854,2.188 5.99,2.573 1.135,0.385 10 false Judged Jammed

U170793E03
2.656,1.281 2.656,1.094 2.656,1.094 2.833,1.094 false 4.333,2.167 4.333,2.49 4.333,2.49 4.563,2.49 false 0.094,0 3.167,0.427 3.073,0.427 10 false Judgment Method (Rotation Speed Comparison) 0.375,1.646 1.74,2.667 1.365,1.021 10 false Power Window Motor Rotation Speed 2.885,0.99 3.885,1.333 1,0.344 10 false Jamming Start 3.042,2.854 4.615,3.229 1.573,0.375 10 false Number of Pulse Edges 4.573,1.646 5.646,2.01 1.073,0.365 10 false Threshold Value 4.625,2.396 5.698,2.74 1.073,0.344 10 false Judged Jammed



c.

Catch Protection Function

i.

The catch protection function automatically stops the power window if a foreign object gets caught in the window during a down operation.


ii.

The power window ECU determines if a foreign object gets caught according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:

Y182661E03
4.26,2.094 4.26,2.333 4.26,2.333 4.896,2.333 false 2.573,1.208 2.573,0.771 2.573,0.771 2.792,0.771 false 4.479,1.563 5.729,2.052 1.25,0.49 10 false Threshold Value 2.854,0.688 4,1.135 1.146,0.448 10 false Catching Start 4.979,2.219 6.219,2.615 1.24,0.396 10 false Judged Caught 2.844,2.771 4.75,3.229 1.906,0.458 10 false Number of Pulse Edges 0.427,1.594 1.792,2.417 1.365,0.823 10 false Power Window Motor Rotation Speed 0.125,0.104 4.115,0.531 3.99,0.427 10 false Judgment Method (Rotation Speed Comparison)



d.

Soft Stop Function

i.

During an up or down operation of the power window, the soft stop function stops the current to the power window motor right before the door glass is fully closed or opened. This reduces the load on the door glass outer weatherstrip.


ii.

Just before the door glass is fully closed, the power window ECU determines if the door glass stop position is detected according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:

Y182662E03
2.563,1.208 2.563,0.896 2.563,0.896 2.656,0.896 false 4.229,2.073 4.229,2.438 4.229,2.438 4.469,2.438 false 0.094,0 3.094,0.177 3,0.177 10 false Judgment Method (Rotation Speed Comparison) 0.5,1.469 1.854,2.49 1.354,1.021 10 false Power Window Motor Rotation Speed 2.698,0.813 4.438,1.115 1.74,0.302 10 false Change of Rotation Speed 2.802,2.781 4.354,3.25 1.552,0.469 10 false Number of Pulse Edges 4.531,2.354 5.646,2.604 1.115,0.25 10 false Judged Soft Stop 4.5,1.552 5.542,1.865 1.042,0.313 10 false Threshold Value




CONSTRUCTION


a.

The power window regulator motor assembly consists of a power window motor and a power window ECU.


b.

The power window ECU contains a built-in pulse sensor (Hall IC). The power window ECU detects the rotation of the power window motor according to output signals from the pulse sensor (Hall IC).

Y181006E02
3.729,0.75 4.656,0.75 true 1.844,0.948 2.365,1.135 true 4.719,0.625 5.031,0.823 0.313,0.198 10 false *2 1.646,0.813 1.958,1.01 0.313,0.198 10 false *1

Text in Illustration
*1 Power Window Motor *2 Power Window ECU


c.

Pulse Sensor (Hall IC)

i.

The pulse sensor (Hall IC) sends pulse signals (2 pulse signals with different phases) in sync with the motor rotation to the power window ECU.

Y181005E01
5.302,2.031 5.948,2.344 true 5.906,0.948 6.271,0.875 true 0.854,1.938 1.854,1.188 true 1.49,2.281 1.844,1.448 true 0.74,0.438 1.573,0.698 true 2.698,1.51 2.948,0.875 true 0.646,1.844 0.823,2.042 0.177,0.198 10 false *2 0.552,0.302 0.75,0.51 0.198,0.208 10 false *1 1.396,2.344 1.615,2.583 0.219,0.24 10 false *3 2.885,0.688 3.198,0.885 0.313,0.198 10 false *4 6.323,0.76 6.635,0.958 0.313,0.198 10 false *3 6.021,2.271 6.333,2.469 0.313,0.198 10 false *2 5.563,0.792 5.729,0.979 0.167,0.188 10 false N 5.031,0.802 5.188,0.979 0.156,0.177 10 false S 5.021,1.448 5.177,1.646 0.156,0.198 10 false N 5.563,1.448 5.719,1.635 0.156,0.188 10 false S

Text in Illustration
*1 Power Window ECU *2 Pulse Sensor (Hall IC)
*3 Magnet *4 Worm Shaft


ii.

The power window ECU detects the amount of door glass movement by counting pulse signal 1 sent from the pulse sensor (Hall IC). The power window ECU also detects the direction of the door glass movement using 2 types of signals: pulse signal 1 and pulse signal 2 which have different phases. The power window ECU controls each function according to the data about the door glass position obtained from the 2 pulse signals.

Y180993E01
1.583,0.563 2.615,0.927 1.031,0.365 10 false Pulse Signal 1 1.604,1.948 2.635,2.313 1.031,0.365 10 false Pulse Signal 1 1.625,2.708 2.656,3.073 1.031,0.365 10 false Pulse Signal 2 3.25,3.25 4.542,3.656 1.292,0.406 10 false Door Glass Down 5.615,3.292 6.698,3.656 1.083,0.365 10 false Door Glass Up 2.938,1.01 4.844,1.417 1.906,0.406 10 false Time for 1 Motor Revolution 0.063,0.458 1.438,1.042 1.375,0.583 10 false Door Glass Movement Amount Detection 0.063,2.26 1.458,2.865 1.396,0.604 10 false Door Glass Movement Direction Detection 2.74,0.292 2.948,0.531 0.208,0.24 10 false HI 2.729,0.646 3,0.927 0.271,0.281 10 false LO 2.76,1.823 2.969,2.063 0.208,0.24 10 false HI 2.75,2.198 3.01,2.479 0.26,0.281 10 false LO 2.771,2.625 2.979,2.865 0.208,0.24 10 false HI 2.75,2.99 2.979,3.26 0.229,0.271 10 false LO 5.094,1.813 5.302,2.052 0.208,0.24 10 false HI 5.073,2.208 5.281,2.448 0.208,0.24 10 false LO 5.063,2.625 5.271,2.865 0.208,0.24 10 false HI 5.083,2.979 5.323,3.25 0.24,0.271 10 false LO


iii.

The power window ECU detects changes in the motor rotation speed using pulse signal 1. As a result, the power window ECU detects the load applied to the door glass and controls the jam protection, catch protection and soft stop functions.

Y146733E04
0.333,1.688 1.708,2.531 1.375,0.844 10 false Door Glass Movement Speed Detection 2.042,0.813 2.969,1.417 0.927,0.604 10 false Pulse Signal 1 2.042,2.406 3.021,3.083 0.979,0.677 10 false Pulse Signal 1 3.104,1.031 3.583,1.406 0.479,0.375 10 false LO 3.104,0.656 3.583,1.031 0.479,0.375 10 false HI 3.104,2.25 3.583,2.625 0.479,0.375 10 false HI 3.104,2.625 3.583,3 0.479,0.375 10 false LO 3.625,1.51 4.167,1.865 0.542,0.354 10 false Normal 4.417,3.104 4.958,3.458 0.542,0.354 10 false Jammed




FAIL-SAFE


a.

If a pulse sensor (Hall IC) in the power window regulator motor assembly malfunctions, the power window control system enters fail-safe mode. For details, refer to the Repair Manual.