Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2017.08
NM27T0E _59 Vehicle Exterior _053648 WIPER / WASHER _0260201 WIPER AND WASHER SYSTEM UN GENERAL/CONTROL/DETAILS F

WIPER / WASHER  WIPER AND WASHER SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


OPERATING CONDITION


a.

Headlight Cleaner System

i.

The headlight cleaner system operates as follows:

Headlight Low Beam Headlight Cleaner Switch Washer Switch (Windshield Wiper Switch Assembly)
On On
(First Time)
On
(Second Time or later)
Turn On Activated Activated Not Activated
Turn Off Activated Not Activated Not Activated




SYSTEM CONTROL


a.

The wiper and washer system has the following functions:

Function Outline
Wiper Vehicle Speed-sensing, Adjustable Interval This function controls the wiper interval time in accordance with the vehicle speed when the windshield wiper switch assembly is in the AUTO or INT position.
Vehicle Speed Switching Automatically selects an intermittent operation when the vehicle is stopped with the windshield wiper switch assembly in the LO position.
Stopped Vehicle Intermittent Wiper Automatically selects an intermittent operation when the windshield wiper switch assembly is switched to the LO position from any positions other than LO with the vehicle stopped.
Raindrop Sensing*1 Controls the wiping interval and speed in accordance with the amount of rain, the vehicle speed and the taillight signals when the windshield wiper switch assembly is in the AUTO position.
Washer-linked Wiper with Drip-prevention To prevent the fluid from dripping after the washer has been operated, this function operates the wipers once after they have operated in unison with the washer.
Washer Headlight Cleaner*2 Sprays washer fluid on the headlight lenses to clean them.
Washer Fluid Level Warning When the volume of washer fluid decreases to below a certain level, the combination meter assembly warns the driver through the warning message on the multi-information display.

*1: Models with raindrop sensing function

*2: Models with headlight cleaner system



b.

Vehicle Speed-sensing, Adjustable Interval Function

i.

When the windshield wiper switch assembly is in the INT position (on models without rain drop sensing function), or AUTO position (on models with rain drop sensing function), the interval time of the wiper is controlled in 3 stages in accordance with the automatic control adjuster position and the vehicle speed.


ii.

The interval time can be controlled steplessly within each range.

Y101071E10
3.938,3.333 3.938,3.469 3.938,3.469 5.271,3.469 false 3.802,1.677 3.802,1.531 3.802,1.531 5.073,1.531 false 2.573,4.042 3.781,4.375 1.208,0.333 10 Vehicle Speed 2.052,2.26 4.438,2.719 2.385,0.458 10 Interval Time Adjustment Range 0.5,1.802 1.104,2.448 0.604,0.646 10 Interval Time 5.125,1.448 6.875,2.104 1.75,0.656 10 Automatic Control Adjuster Position: SLOW 5.365,3.375 7.073,4.052 1.708,0.677 10 Automatic Control Adjuster Position: FAST 1.115,0.333 1.698,0.615 0.583,0.281 10 Sec. 1.146,0.615 1.521,0.833 0.375,0.219 10 15 1.177,1.594 1.479,1.802 0.302,0.208 10 10 1.208,2.552 1.469,2.76 0.26,0.208 10 5 1.75,3.635 1.958,3.927 0.208,0.292 10 0 4.531,3.677 5.427,3.938 0.896,0.26 10 km/h (mph) 2.396,3.625 3.135,3.875 0.74,0.25 10 20 (12) 3.177,3.646 3.823,3.885 0.646,0.24 10 40 (25) 3.958,3.635 4.583,3.938 0.625,0.302 10 60 (37)



c.

Vehicle Speed Switching Function

i.

When the windshield wiper switch assembly is in the LO position and the vehicle has stopped running, wiper operation is automatically switched to intermittent operation.


ii.

The front wiper relay circuit judges that the vehicle is being driven if one of the following conditions is met:

·

The vehicle speed is anything other than 0 km/h (0 mph).

·

The stop light switch and the parking brake switch are off and the shift lever is in a position other than P or N.



iii.

If other conditions exist, the front wiper relay circuit judges that the vehicle is stopped. It controls the wipers as shown in the timing chart below.


iv.

When the vehicle stops running and the windshield wiper switch assembly is in the LO position, the wipers operate twice in LO. It then switches to intermittent operation with an interval time of approximately 2.5 seconds. If the vehicle starts driving during this intermittent wiper operation, the wiper returns automatically to LO operation.



d.

Stopped Vehicle Intermittent Wiper Function

i.

When the windshield wiper switch assembly is changed to the LO position while the vehicle is stopped, the wipers operate 3 times in LO. It then switches automatically to an intermittent operation with an interval time of approximately 2.5 seconds.


ii.

When the automatic control adjuster is in the FAST position, the wipers operate in LO when the vehicle is stopped.

Y104794E09
0.073,0.24 0.604,1.583 0.531,1.344 10 false Wiper Control Switch 0.083,1.771 1.094,2.708 1.01,0.938 10 false Motor Detection Switch Signal 0.135,2.948 0.833,3.792 0.698,0.844 10 false Wiper Operation 1.354,0.458 2.396,0.823 1.042,0.365 10 false LO Position 1.156,0.938 2.302,1.271 1.146,0.333 10 false Other Positions 1.833,1.677 2.125,2.021 0.292,0.344 10 false +B 1.771,2.135 2.208,2.51 0.438,0.375 10 false GND 1.479,2.823 2.292,3.177 0.813,0.354 10 false Operating 1.552,3.323 2.208,3.75 0.656,0.427 10 false Stopped 2.219,3.615 3.667,3.979 1.448,0.365 10 false Except LO Operation 4.031,3.615 5.042,4 1.01,0.385 10 false LO Operation 5.406,3.615 6.458,3.99 1.052,0.375 10 false INT Operation 5.25,2.302 5.49,2.583 0.24,0.281 10 false T1 5.677,2.302 5.938,2.625 0.26,0.323 10 false T1 6.146,2.302 6.417,2.563 0.271,0.26 10 false T1 0.115,3.875 1.865,4.25 1.75,0.375 10 false T1: Approx. 2.5 seconds



e.

Raindrop Sensing Function

i.

The raindrop sensing function controls the wiper timing in accordance with the amount of raindrops that strikes the windshield when the windshield wiper switch assembly is in the AUTO position.


ii.

The front wiper relay circuit controls the timing based on the signal from the rain sensor.



f.

Washer-linked Wiper with Drip-prevention Function

i.

When the windshield wiper switch assembly is set to OFF or AUTO and the washer switch is turned on for approximately 0.2 seconds or more, the wipers start operating in LO at the same time as the washer fluid is sprayed.


ii.

The wipers operate 3 times in LO after the washer switch is turned off.


iii.

As shown in the following diagram, after the end of this operation, the wipers operate once more. They do so after an interval determined by vehicle speed, so that any washer fluid drips are wiped away.

Y101074E19
2.146,0.552 2.354,0.885 0.208,0.333 10 false On 2.125,1.604 2.333,1.938 0.208,0.333 10 false On 2.125,2.792 2.333,3.125 0.208,0.333 10 false On 2.375,0.146 4.448,0.479 2.073,0.333 10 false Approx. 0.2 seconds 4.667,3.698 4.865,4.031 0.198,0.333 10 false T1 2.146,1.115 2.354,1.448 0.208,0.333 10 false Off 2.125,2.135 2.333,2.469 0.208,0.333 10 false Off 2.135,3.375 2.344,3.708 0.208,0.333 10 false Off 0.26,4.438 2.74,4.771 2.479,0.333 10 false T1: Refer to the interval time table 1.167,0.885 1.688,1.625 0.521,0.74 10 false Washer Switch 1.208,1.896 1.719,2.583 0.51,0.688 10 false Washer Motor 1.24,3.229 1.875,3.875 0.635,0.646 10 false Wiper Operation 3.573,4.021 4.479,4.667 0.906,0.646 10 false Washer-linked Operation 5.083,3.99 6.021,4.667 0.938,0.677 10 false Drip-prevention Operation

Interval Time Table
Vehicle Speed (km/h [mph]) Interval Time
Approx. 0 to 59 (0 to 37) Approx. 3 seconds
Approx. 60 to 79 (37 to 49) Approx. 5 seconds
Approx. 80 to 119 (50 to 74) Approx. 7 seconds
Approx. 120 to 159 (75 to 99) Approx. 5 seconds
Approx. 160 to 169 (99 to 105) Approx. 3 seconds
Approx. 170 or more (106 or more) No operation



g.

Washer Fluid Level Warning

i.

When the volume of washer fluid decreases to below a certain level, the combination meter assembly displays the messages "Low Washer Fluid" on the multi-information display to warning the driver.




CONSTRUCTION


a.

Rain Sensor

i.

The rain sensor consists of a Light Emitting Diode (LED) that emits infrared rays, a photo diode that can receive those rays, a lens and rain sensor tape.

Y101102E10
2.604,0.958 1.594,0.958 true 2.948,1.292 1.594,1.292 true 2.781,1.688 2.781,2.365 true 4.729,1.656 5.531,1.656 true 0.448,0.854 1.719,1.146 1.271,0.292 10 false Rain Sensor Tape 1.25,1.188 1.625,1.479 0.375,0.292 10 false Lens 2.438,2.417 3.333,2.635 0.896,0.219 10 false Photo Diode 5.583,1.563 6.052,1.771 0.469,0.208 10 false LED

HINT:

If the rain sensor tape has been peeled off during a windshield glass replacement, make sure to affix new rain sensor tape. Failure to do so will lead to a system malfunction.



ii.

If no raindrops are present in the detection area, the infrared rays emitted by the LED are all reflected from the outer surface of the windshield glass and are received by the photo diode.


iii.

If raindrops are present in the detection area, a portion of the emitted infrared rays penetrates the windshield glass due to the change in the difference of the index of refraction between the glass and the area outside the windshield (difference between air and water). The ability of the windshield glass to reflect all light back inside changes due to the presence of raindrops. This change of internal reflection due to the presence of water reduces the amount of infrared rays that are received by the photo diode. The amount of this reduction is then used to determine the amount of raindrops. Thus, this function selects the INT, LO, and HI wiper operations in order to operate the wipers at an optimal speed and timing.

Y101103E10
4.885,0.823 4.885,0.385 4.885,0.385 5.063,0.385 false 5.229,1.021 5.229,0.719 5.229,0.719 5.427,0.719 false 0.865,1.188 0.865,0.375 0.865,0.375 1.073,0.375 true 1.469,1.406 1.469,0.708 1.469,0.708 1.656,0.708 true 1.188,1.99 1.188,2.406 true 2.51,1.865 2.51,2.438 true 2.729,1.979 3.323,1.979 true 4.552,1.99 4.552,2.406 true 5.885,1.865 5.885,2.427 true 6.073,1.979 6.667,1.979 true 1.125,0.271 2.531,0.604 1.406,0.333 10 false Windshield Glass 1.698,0.604 2.854,0.99 1.156,0.385 10 false Infrared Ray 0.854,2.375 1.823,2.729 0.969,0.354 10 false Photo Diode 2.167,2.406 3.198,2.729 1.031,0.323 10 false Infrared Ray 3.375,1.875 3.844,2.24 0.469,0.365 10 false LED 5.469,0.625 6.323,0.99 0.854,0.365 10 false Raindrop 5.115,0.281 6.313,0.625 1.198,0.344 10 false Infrared Ray 4.219,2.385 5.156,2.708 0.938,0.323 10 false Photo Diode 5.542,2.406 6.542,2.729 1,0.323 10 false Infrared Ray 6.708,1.885 7.104,2.25 0.396,0.365 10 false LED



b.

Washer Nozzle

i.

Spray type washer nozzles are located under the engine hood to ensure good appearance. These nozzles can spray windshield washer fluid over a wide area by spraying it in a fan shape. The washer fluid volume has been reduced so as not to hinder the driver's view when the washer system is operated.

Y101075E10
0.906,0.615 0.75,0.615 0.75,0.615 0.75,1.292 false 1.76,1.198 1.76,2.146 true 6.302,0.51 6.844,0.896 0.542,0.385 10 false Fluid Volume 0.917,0.521 2.094,0.917 1.177,0.396 10 false Engine Hood 1.281,2.271 2.25,2.667 0.969,0.396 10 false Washer Nozzle 6.302,1.208 6.99,1.854 0.688,0.646 10 false Main Flow Center

HINT:

Spray type washer nozzles cannot be adjusted because of their structure. Do not attempt to adjust the nozzles as it could damage them. If adjustment is necessary, adjust the nozzles by replacing them with nozzles that have different spray angles. For details, refer to the Repair Manual.





FAIL-SAFE


a.

The following fail-safe measures are taken if a malfunction is detected by the windshield wiper switch assembly.

Trouble Area Condition
Wiper Motor Malfunction Stops the operation of the raindrop sensing function.
Communication Signal Malfunction Rain Sensor Stops the operation of the raindrop sensing function.
When a signal cannot be received from the rain sensor, the raindrop sensing function is not performed and the status that existed prior to the occurrence of abnormality is maintained.
Combination Meter Assembly
·

Stops the operation of the vehicle speed-sensing, adjustable interval vehicle function.

·

Stops the operation of the speed switching function.

·

Stops the operation of the stopped vehicle intermittent wiper function.

·

The wiper interval can be adjusted.