Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
NM27T0E _51 Engine / Hybrid System _053574 1KD-FTV ENGINE CONTROL _0260099 ECD SYSTEM UN GENERAL/CONTROL/DETAILS F

1KD-FTV ENGINE CONTROL  ECD SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function
ECM Forest 1 The ECM effects overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Injector Driver DC/DC Converter 1 The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system.
Turbo Pressure Sensor Semiconductor Silicon Chip Type 1 This sensor uses built-in semiconductors to detect the intake manifold pressure.
Atmospheric Pressure Sensor Semiconductor Silicon Chip Type 1 This sensor, which is built into the ECM, uses semiconductors to detect the atmospheric pressure.
Fuel Pressure Sensor Semiconductor Strain Gauge Type 1 This sensor uses built-in semiconductors to detect the internal pressure of the common-rail.
Pressure Discharge Valve Solenoid Type 1 The pressure discharge valve regulates the fuel pressure.
Crank Position Sensor Pick-up Coil Type
(Rotor Teeth/36-2)
1 This sensor detects the engine speed and performs the cylinder identification.
Camshaft Position Sensor Pick-up Coil Type
(Rotor Teeth/5)
1 This sensor performs the cylinder identification.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor uses a built-in hot-wire to directly detect the intake air mass.
Intake Air Temperature Sensor
(Built into Intake Mass Air Flow Meter Sub-assembly)
Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
Intake Air Temperature Sensor
(Intercooler Outlet)
Thermistor Type 1 This sensor detects the intake air temperature past the intercooler.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Fuel Temperature Sensor Thermistor Type 1 This sensor detects the fuel temperature in the supply pump by means of an internal thermistor.
Throttle Position Sensor Non-contact Type 1 This sensor detects the diesel throttle valve opening angle.
Accelerator Pedal Position Sensor Non-contact Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Nozzle Vane Position Sensor Non-contact Type 1 This sensor detects the nozzle vane position.
Suction Control Valve (SCV) Linear Solenoid Valve 1 The SCV position is controlled by the signals from the ECM, and a fuel volume that suits the SCV position is drawn into the pumping portion (plunger portion).
Injector Assembly 8-hole, Solenoid Type 4 The injector injects the fuel to the combustion chamber in accordance with the ECM signals via the EDU.



SYSTEM CONTROL


a.

The engine control system has the following features. The ECM controls these systems:

System Outline
Fuel Injection Volume Control Based on the signals received from the sensors, the ECM determines the fuel injection volume in accordance with the engine condition.
Fuel Injection Timing Control Based on the signals received from the sensors, the ECM determines the fuel injection timing in accordance with the engine condition.
During Starting Control To facilitate startability, the ECM optimally controls the injection volume and injection timing during starting.
Idle Speed Control The ECM determines the idle speed in accordance with the engine condition, and controls the fuel injection volume in order to maintain the target idle speed.
Fuel Pressure Control Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) and pressure discharge valve in accordance with engine operating conditions.
Pilot Injection Control Based on the signals received from the sensors, the ECM determines pilot injection volume/timing and interval (between pilot injection and main injection) in accordance with the engine condition.
Glow Plug Control The ECM controls the length of time for which the current is applied to the glow plug assemblies, in accordance with the engine coolant temperature.
Diesel Throttle Control
·

Controls the diesel throttle valve opening angle in accordance with the engine condition.

·

Fully closes the diesel throttle valve in order to reduce the vibration when the engine is stopped.


Swirl Control
·

Based on the signals received from the sensors, the ECM controls the vacuum that is directed to the actuator via the VSVs, in order to open and close the valve.

·

Controls the valve opening in three stages: fully open, semi-open, and fully closed.


Turbocharger Control Based on the signals received from the sensors, the ECM controls the actuator in accordance with the engine condition.
Air Conditioning Cut-off Control By controlling the air conditioning compressor on or off in accordance with the engine condition, driveability is maintained.
Starter Control*1 Once the engine switch is pushed, this control continues to operate the starter until the engine is started.
Engine Immobiliser Prohibits fuel injection if an attempt is made to start the engine with an invalid ignition key.
Fuel Pump Control*2 The ECM operates the fuel pump to optimally control the transfer of the fuel in the fuel tank.
Engine Mount Control When the engine speed is low and the vehicle is operating at a low speed, this control utilizes vacuum to soften the engine mount characteristics in order to restrain the engine vibration at idle.
Brake Override System The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual.)
Drive Start Control If an abnormal shift (R to D/S, D/S to R, N to R, P to D/S, P to R) is detected while accelerating, a warning is displayed in the combination meter assembly and engine output is reduced to limit the acceleration, helping to avoid a collision.
Diagnosis When the ECM detects a malfunction, it diagnoses and memorizes the failed section.
Fail-safe When the ECM detects a malfunction, it stops or controls the engine in accordance with the data already stored in the memory.

*1: Models with entry and start system

*2: Models with dual fuel tank




FUNCTION


a.

Fuel Injection Volume Control

i.

The ECM calculates 2 types of values: the basic injection volume and the maximum injection volume. Then, the ECM compares the basic and maximum injection volumes, and determines the smaller calculated value to be the final injection volume.

W102241E11
0.219,0.51 1.323,1.302 1.104,0.792 10 false Accelerator Pedal Position Sensor 0.24,0.052 1.896,0.375 1.656,0.323 10 false - Basic Injection Volume - 1.719,1.208 2.083,1.594 0.365,0.385 10 false ECM 2.5,2.094 4.385,2.479 1.885,0.385 10 false Idle Speed Control Correction 5.521,1.625 6.792,2.365 1.271,0.74 10 false Engine Coolant Temperature Sensor 2.281,1.417 4.604,1.823 2.323,0.406 10 false Calculation of Basic Injection Volume 5.385,0.49 6.833,0.875 1.448,0.385 10 false Crank Position Sensor 5.677,0.917 6.615,1.302 0.938,0.385 10 false Engine Speed

W102242E11
0.344,1.021 0.708,1.406 0.365,0.385 10 false ECM 4.635,1.979 6.844,2.385 2.208,0.406 10 false Engine Coolant Temperature Sensor 4.917,2.573 6.938,3 2.021,0.427 10 false Fuel Temperature Sensor 4.833,3.24 6.771,3.625 1.938,0.385 10 false Intake Air Temperature Sensor 4.927,3.698 6.646,4.51 1.719,0.813 10 false Intake Mass Air Flow Meter Sub-assembly 5.063,4.625 6.531,5.01 1.469,0.385 10 false Turbo Pressure Sensor 0.74,1.302 2.792,1.948 2.052,0.646 10 false Basic/Maximum Injection Volume (Map Data Inside of ECM) 0.958,3.219 2.667,4.406 1.708,1.188 10 false Maximum Injection Volume Correction 5.083,1.021 6.552,1.406 1.469,0.385 10 false Crank Position Sensor 5.333,1.417 6.271,1.802 0.938,0.385 10 false Engine Speed 5.292,5.156 6.313,5.531 1.021,0.375 10 false Intake Air Mass 0.25,0.583 2.271,0.906 2.021,0.323 10 false - Maximum Injection Volume -

W102243E09
0.219,0.083 2.448,0.406 2.229,0.323 10 false - Final Injection Volume Decision - 0.25,0.531 0.615,0.917 0.365,0.385 10 false ECM 2.823,1.292 3.635,1.677 0.813,0.385 10 false Comparison 3.75,0.708 4.667,1.094 0.917,0.385 10 false Fuel Pressure 4.771,1.302 5.125,1.677 0.354,0.375 10 false Final 6.26,2.104 6.781,2.479 0.521,0.375 10 false Injector 6.271,1.156 6.771,1.823 0.5,0.667 10 false Injector Driver 0.792,0.729 2.281,1.135 1.49,0.406 10 false Basic Injection Volume 0.667,1.854 2.406,2.26 1.74,0.406 10 false Maximum Injection Volume



b.

Fuel Injection Timing Control

i.

Fuel injection timing is controlled as shown below:

W102244E08
0.344,1.865 0.708,2.25 0.365,0.385 10 false ECM 4.646,1.823 6.938,2.219 2.292,0.396 10 false Engine Coolant Temperature Sensor 4.844,2.469 6.76,2.854 1.917,0.385 10 false Intake Air Temperature Sensor 5.063,3.167 6.531,3.531 1.469,0.365 10 false Turbo Pressure Sensor 0.729,2.063 2.115,2.469 1.385,0.406 10 false Basic Injection Timing 0.938,4.125 1.958,4.521 1.021,0.396 10 false Injection Timing 3.625,0.25 5.063,0.635 1.438,0.385 10 false Crank Position Sensor 3.896,0.667 4.833,1.052 0.938,0.385 10 false Engine Speed 6.448,4.156 6.969,4.531 0.521,0.375 10 false Injector 4.708,4.135 5.635,4.51 0.927,0.375 10 false Injector Driver 0.333,0.271 2.469,0.74 2.135,0.469 10 false Accelerator Pedal Position Sensor 2.219,2.76 2.948,3.146 0.729,0.385 10 false Correction



c.

During Starting Control

i.

The starting injection volume is determined by adjusting the basic injection volume in accordance with the starter on signals (on time) and engine coolant temperature sensor signals and engine speed signal. When the engine is cold, the engine coolant temperature will be lower and the injection volume will be greater.

W102245E07
0.333,0.531 0.698,0.917 0.365,0.385 10 false ECM 4.656,1.521 6.969,1.917 2.313,0.396 10 false Engine Coolant Temperature Sensor 5.406,0.865 6.198,1.26 0.792,0.396 10 false Start Signal 0.729,0.771 2.177,1.167 1.448,0.396 10 false Basic Injection Volume 1.104,1.635 1.813,2.052 0.708,0.417 10 false Correction 5.125,2.135 6.563,2.521 1.438,0.385 10 false Crank Position Sensor 0.208,0.094 2.229,0.417 2.021,0.323 10 false - Injection Volume Control -


ii.

To determine the starting injection timing, the target injection timing is corrected in accordance with the starter signals, engine coolant temperature, and engine speed. When the engine coolant temperature is low, if the engine speed is high, the injection timing is advanced.

W102246E08
0.333,0.51 0.698,0.896 0.365,0.385 10 false ECM 4.635,1.375 6.917,1.771 2.281,0.396 10 false Engine Coolant Temperature Sensor 5.427,0.688 6.219,1.083 0.792,0.396 10 false Start Signal 0.969,0.729 1.917,1.865 0.948,1.135 10 false Target Injection Correction 5.063,2.042 6.563,2.427 1.5,0.385 10 false Crank Position Sensor 0.219,0.135 2.24,0.458 2.021,0.323 10 false - Injection Timing Control -



d.

Idle Speed Control

i.

Idle speed control correction is controlled as shown below:

W102247E22
0.354,0.219 0.885,0.594 0.531,0.375 10 false ECM 4.688,0.781 7.063,1.229 2.375,0.448 10 false Engine Coolant Temperature Sensor 5.115,1.365 6.813,1.802 1.698,0.438 10 false Vehicle Speed Sensor 5.406,1.938 6.521,2.375 1.115,0.438 10 false Start Signal 5.073,2.531 6.844,2.938 1.771,0.406 10 false Air Conditioning Signal 5.313,3.135 6.479,3.552 1.167,0.417 10 false Idle-up Signal 0.792,0.438 2.646,0.875 1.854,0.438 10 false Target Speed Calculation 0.781,3.604 1.667,4.25 0.885,0.646 10 false Actual Engine Speed 5.115,3.74 6.771,4.198 1.656,0.458 10 false Crank Position Sensor 4.729,0.198 6.969,0.625 2.24,0.427 10 false Accelerator Pedal Position Sensor 2.188,2.771 3.219,3.49 1.031,0.719 10 false Injection Volume Correction 0.802,2.75 1.75,3.177 0.948,0.427 10 false Comparison



e.

Fuel Pressure Control

i.

The ECM calculates the target injection pressure (32 MPa to 160 MPa) based on the signals from the accelerator pedal position sensor and the crank position sensor. To control fuel pressure, signals sent to the Suction Control Valve (SCV) of the supply pump assembly regulate the suction volume, and signals sent to the pressure discharge valve of the common-rail regulate the discharge volume, so that the pressure detected by the fuel pressure sensor matches the target injection pressure.

W100202E11
1.677,0.292 2.625,0.917 0.948,0.625 10 false Crank Position Sensor 3.167,0.302 4.802,0.948 1.635,0.646 10 false Accelerator Pedal Position Sensor 2.229,1.708 3.615,2.417 1.385,0.708 10 false Calculation of Target Common-rail Pressure 2.24,3.063 3.708,3.573 1.469,0.51 10 false Fuel Pressure Sensor 0.885,3.906 1.26,4.188 0.375,0.281 10 false SCV 2.479,3.792 3.271,4.458 0.792,0.667 10 false Common-rail Assembly 4.542,3.823 5.781,4.479 1.24,0.656 10 false Pressure Discharge Valve 4.719,5.125 5.719,5.5 1,0.375 10 false Injector Driver 2.635,5.125 3.344,5.5 0.708,0.375 10 false Injector 1.802,1.281 2.167,1.531 0.365,0.25 10 false ECM



f.

Pilot Injection Control

i.

Pilot injection is a method that provides an auxiliary fuel injection before the main fuel injection takes place. The purpose of pilot injection is to gently start the combustion of the fuel of the main injection in order to reduce combustion noise.

State Pilot Injection Ordinary Injection
Fuel Injection
W132982E01
1.219,1.563 1.375,1.563 1.375,1.563 1.458,1.302 false 1.792,1.573 1.688,1.573 1.688,1.573 1.635,1.302 false 0.385,1.458 1.271,1.802 0.885,0.344 10 false Pilot Injection 1.833,1.49 2.719,1.833 0.885,0.344 10 false Main Injection

W132983

Combustion Pressure
W132984

W132985



ii.

During pilot injection, the pilot injection volume, timing, and interval (between pilot injection and main injection) are controlled as shown below:

W102252E09
0.344,1.531 0.708,1.917 0.365,0.385 10 false ECM 4.646,1.51 6.948,1.906 2.302,0.396 10 false Engine Coolant Temperature Sensor 4.865,2.167 6.802,2.552 1.938,0.385 10 false Intake Air Temperature Sensor 5.031,2.833 6.625,3.219 1.594,0.385 10 false Turbo Pressure Sensor 0.729,1.719 2.396,2.458 1.667,0.74 10 false Basic Pilot Injection Timing (Volume, Timing, Interval) 0.729,3.813 2.302,4.542 1.573,0.729 10 false Pilot Injection Timing (Volume, Timing, Interval) 3.656,0.271 5.125,0.656 1.469,0.385 10 false Crank Position Sensor 3.927,0.667 4.865,1.052 0.938,0.385 10 false Engine Speed 6.458,3.844 6.979,4.219 0.521,0.375 10 false Injector 4.698,3.833 5.531,4.219 0.833,0.385 10 false Injector Driver 0.344,0.281 2.479,0.75 2.135,0.469 10 false Accelerator Pedal Position Sensor 2.219,2.594 2.948,2.979 0.729,0.385 10 false Correction



g.

Glow Plug Control

i.

The ECM controls the length of time for which the current is applied to the glow plug relay when the engine starts in accordance with engine coolant temperature to control the length of time for which the current is applied to the glow plug assemblies.



h.

Diesel Throttle Control

i.

The ECM controls the opening of the diesel throttle valve to reduce the noise caused when idling and decelerating, and the noise and vibrations caused when stopping the engine.



i.

Swirl Control

i.

The ECM controls the swirl control valve position to improve torque in the low engine speed range and to optimize exhaust emissions.



j.

Turbocharger Control

i.

The ECM controls the nozzle vane position, in order to obtain the calculated target turbo pressure appropriate to the engine operating conditions.



k.

Starter Control (Models with Entry and Start System)

i.

Depressing the clutch pedal*1 or brake pedal*2 and pressing the engine switch once will operate the starter continuously until the engine has started completely. Operability and the starting operation have thereby been improved.

*1: Models with manual transmission

*2: Models with automatic transmission



ii.

If the certification ECU (smart key ECU assembly) detects a start signal, it will monitor the engine speed signal (NE) from the ECM and operate the starter continuously until it determines that the engine has started completely.



l.

Fuel Pump Control (Models with Dual Fuel Tank)

i.

The fuel pump control system transfers fuel from the sub fuel tank to the main fuel tank.



m.

Engine Mount Control

i.

When the engine is idling and the vehicle is operating at a low speed, this engine mount utilizes the vacuum from the vacuum pump (for the engine) to move the diaphragm in the mount, which switches the passages for the fluid (water) that is sealed in. By softening the dampening characteristics of the mount in this manner, this mount restrains engine vibration.




CONSTRUCTION


a.

ECM

i.

The forest type CPU of the ECM is used to increase the speed for processing the signals.



b.

Injector Driver

i.

The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system.


ii.

The ECM constantly monitors the injector driver and stops the engine when an abnormal condition is detected.



c.

Turbo Pressure Sensor

i.

The turbo pressure sensor consists of a semiconductor which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the intake air pressure into an electrical signal, and sends it to the ECM in an amplified form.

W102690E12
1.177,1.177 1.177,0.229 1.177,0.229 0.979,0.229 true 0.229,0.135 0.99,0.51 0.76,0.375 10 false Sensor Unit 4.188,2.094 4.323,2.302 0.135,0.208 10 false 0 3.615,1.156 4.104,1.885 0.49,0.729 10 false Output Voltage 4.365,2.333 6.021,2.729 1.656,0.396 10 false Intake Manifold Pressure 6.042,2.115 6.448,2.51 0.406,0.396 10 false (kPa) 4.125,0.521 4.396,0.729 0.271,0.208 10 false (V) 4.125,0.156 5.938,0.521 1.813,0.365 10 false - Sensor Characteristic -



d.

Fuel Pressure Sensor

i.

The fuel pressure sensor, which is mounted on the common-rail, outputs a signal that represents the fuel pressure in the common-rail to the ECM in order to constantly regulate the fuel at an optimal pressure.


ii.

The fuel pressure sensor consists of a semiconductor which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it.


iii.

The fuel pressure sensor has 2 circuits (main and sub), which enable the ECM to constantly compare the values detected by the two circuits. As a result, highly precise values can be detected, which also enables a higher level of fail-safe control.

U170782E03
5.281,1.594 5.281,2.646 5.281,2.646 5.396,2.646 true 5.781,1.615 5.781,1.896 5.781,1.896 5.896,1.896 true 2.281,1.219 2.281,0.51 2.281,0.51 1.958,0.51 true 1.906,3.406 2.865,3.75 0.958,0.344 10 false Output Voltage 2.823,2.635 4.635,3 1.813,0.365 10 false - Sensor Characteristic - 3.271,3.146 3.625,3.448 0.354,0.302 10 false Main 3.708,3.583 4.021,3.865 0.313,0.281 10 false Sub 2.646,3.031 2.896,3.219 0.25,0.188 10 false (V) 4.479,4.219 4.917,4.406 0.438,0.188 10 false (MPa) 3.146,4.354 4.073,4.698 0.927,0.344 10 false Fuel Pressure 4.063,4.208 4.333,4.396 0.271,0.188 10 false 190 5.938,1.802 6.75,2.521 0.813,0.719 10 false Common-rail Assembly 5.448,2.542 6.833,2.865 1.385,0.323 10 false Fuel Pressure Sensor 1.26,2.073 3.531,2.396 2.271,0.323 10 false Fuel Pressure Sensor Cross Section 0.854,0.427 1.958,0.74 1.104,0.313 10 false Detection Portion



e.

Pressure Discharge Valve

i.

The pressure discharge valve regulates the fuel pressure. In the pressure discharge valve, the plunger opens and closes in accordance with the actuation signals from the injector driver. Thus, it regulates pressure by releasing excess pressure from the common-rail. In addition, it has a pressure reduction function in case of emergency.

W102426E02
5.448,1.396 5.448,0.75 5.448,0.75 5.583,0.75 true 2.125,1.24 2.125,0.583 2.125,0.583 1.979,0.583 true 1.156,1.219 1.156,0.573 1.156,0.573 1.01,0.573 true 3.604,0.448 3.813,0.635 0.208,0.188 10 false *a 1.771,0.51 1.979,0.698 0.208,0.188 10 false *2 5.604,0.656 5.813,0.844 0.208,0.188 10 false *3 0.813,0.51 1.021,0.698 0.208,0.188 10 false *1

Text in Illustration
*1 Common-rail Assembly *2 Pressure Discharge Valve
*3 Plunger - -
*a Pressure Discharge Valve Cross Section - -
V100135

Fuel from Common-rail (High Pressure)
V100136

Fuel to Fuel Tank (Excess Pressure)



f.

Crank Position Sensor and Camshaft Position Sensor

i.

The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crank position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top dead center.


ii.

To detect the camshaft position, a protrusion that is provided on the timing pulley is used to generate 5 pulses for every 2 revolutions of the crankshaft.

W103761E10
2.781,1.573 2.302,0.375 2.302,0.375 2.01,0.375 true 4.344,1.083 4.646,0.375 4.646,0.375 5.125,0.375 true 3.885,4.281 4.031,3.948 4.031,3.948 4.25,3.948 false 0.542,0.26 2.021,0.583 1.479,0.323 10 false Crank Position Sensor 5.198,0.292 6.854,0.615 1.656,0.323 10 false Camshaft Position Sensor 1.146,2.052 2.396,2.438 1.25,0.385 10 false 34 Pulses/360° CA 1.938,7.406 3.188,7.792 1.25,0.385 10 false 34 Pulses/360° CA 4.104,7.417 5.354,7.802 1.25,0.385 10 false 34 Pulses/360° CA 4.781,2.115 5.948,2.5 1.167,0.385 10 false 5 Pulses/720° CA 4.354,3.854 5.521,4.24 1.167,0.385 10 false 5 Pulses/720° CA 0.125,3.625 1.99,4.01 1.865,0.385 10 false - Sensor Output Waveforms - 1.99,4.573 2.646,4.958 0.656,0.385 10 false 180° CA 3.083,4.563 3.74,4.948 0.656,0.385 10 false 180° CA 4.115,4.573 4.771,4.958 0.656,0.385 10 false 180° CA



g.

Intake Mass Air Flow Meter Sub-assembly

i.

This engine uses the hot-wire type air flow meter designed for direct electrical measurement of the intake air mass flow.


ii.

This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

W102255E05
5.208,1.292 5.552,0.958 5.552,0.958 5.771,0.958 true 5.052,1.313 5.49,2.115 5.49,2.115 5.771,2.115 true 4.969,1.229 4.646,1.635 4.646,1.635 4.427,1.635 true 4.208,1.563 4.438,1.844 0.229,0.281 10 false *1 5.833,0.885 6.063,1.167 0.229,0.281 10 false *2 5.833,2 6.063,2.281 0.229,0.281 10 false *3 2.323,0.042 2.458,0.229 0.135,0.188 10 false A 2.323,2.51 2.438,2.677 0.115,0.167 10 false A 4.917,2.417 5.156,2.646 0.24,0.229 10 false *a

Text in Illustration
*1 Platinum Hot-wire Element *2 Intake Air Temperature Sensor
*3 Temperature Sensing Element - -
*a A - A Cross Section - -
V100136

Air Flow - -



h.

Throttle Position Sensor

i.

The throttle position sensor is mounted on the diesel throttle body assembly. To detect the opening angle of the diesel throttle valve, the throttle position sensor converts the magnetic flux density, that changes when the magnetic yoke (located on the same axis as the diesel throttle valve shaft) rotates around the Hall IC, into electric signals to operate the throttle control motor.

W102256E08
1.521,1.375 1.073,1.854 1.073,1.854 0.938,1.854 true 1.521,1.219 1.521,0.156 1.521,0.156 1.135,0.156 true 2.458,1.74 2.125,2.406 2.125,2.406 1.927,2.406 true 0.51,1.75 0.958,2.094 0.448,0.344 10 false Hall IC 3.333,1.094 3.854,1.844 0.521,0.75 10 false Output Voltage 3.896,2.448 6.365,2.781 2.469,0.333 10 false Opening Angle of Diesel Throttle Valve 0.656,2.302 1.99,2.74 1.333,0.438 10 false Diesel Throttle Valve 3.677,0.219 3.917,0.563 0.24,0.344 10 false (V) 3.76,0.563 3.938,0.833 0.177,0.271 10 false 5 3.76,2.229 3.938,2.5 0.177,0.271 10 false 0 6.354,2.302 6.667,2.573 0.313,0.271 10 false 100 0.563,0.063 1.135,0.708 0.573,0.646 10 false Magnetic Yoke



i.

Accelerator Pedal Position Sensor

i.

The magnetic yoke that is mounted at the base of the accelerator pedal arm moves around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur at that time into electrical signals, and outputs them in the form of accelerator pedal effort to the ECM.

W102204E05
1.375,2 1.031,2.354 1.031,2.354 0.917,2.354 true 2.229,2.875 1.958,3.146 1.958,3.146 1.875,3.146 true 2.052,1.823 2.052,0.906 2.052,0.906 2.229,0.906 true 4.219,2.896 4.219,3.052 true 4.521,2.375 3.677,2.74 3.677,2.74 3.563,2.74 true 4.521,1.938 3.677,1.573 3.677,1.573 3.563,1.573 true 4.615,1.635 4.615,1.125 4.615,1.125 4.365,1.125 true 3.146,4.917 3.292,4.917 3.292,4.917 3.292,5.115 false 4.052,5.354 3.906,5.354 3.906,5.354 3.906,5.156 false 0.479,2.271 0.958,2.594 0.479,0.323 10 false Hall IC 3.125,1.5 3.604,1.823 0.479,0.323 10 false Hall IC 3.115,2.646 3.594,2.969 0.479,0.323 10 false Hall IC 2.281,0.813 3.396,1.25 1.115,0.438 10 false Magnetic Yoke 3.802,3.052 4.75,3.375 0.948,0.323 10 false Magnetic Yoke 3.885,1.052 4.406,1.375 0.521,0.323 10 false Magnet 5.271,1.531 5.667,1.719 0.396,0.188 10 false VPA 6.042,2.125 6.375,2.406 0.333,0.281 10 false ECM 5.271,1.813 5.646,2.042 0.375,0.229 10 false EPA 5.271,2.094 5.74,2.271 0.469,0.177 10 false VCPA 5.271,2.313 5.708,2.594 0.438,0.281 10 false VPA2 4.104,5.271 4.438,5.552 0.333,0.281 10 false VPA 2.74,4.823 3.135,5.104 0.396,0.281 10 false VPA2 5.271,2.625 5.708,2.906 0.438,0.281 10 false EPA2 5.271,2.927 5.708,3.208 0.438,0.281 10 false VCP2 0.438,3.042 2.042,3.448 1.604,0.406 10 false Accelerator Pedal Arm 2.406,6.385 4.656,6.708 2.25,0.323 10 false Accelerator Pedal Depressed Angle 1.573,5.063 2.063,5.75 0.49,0.688 10 false Output Voltage 2.031,6 2.927,6.323 0.896,0.323 10 false Fully Closed 2.24,4.5 2.375,4.688 0.135,0.188 10 false 5 2.177,4.26 2.406,4.458 0.229,0.198 10 false (V) 2.208,5.656 2.344,5.844 0.135,0.188 10 false 0 4.281,6 5.177,6.323 0.896,0.323 10 false Fully Open 1.792,3.948 5.563,4.26 3.771,0.313 10 false - Accelerator Pedal Position Sensor Output Characteristics -



j.

Nozzle Vane Position Sensor

i.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

W102257E03
1.604,0.938 1.146,1.583 1.146,1.583 1,1.583 true 1.906,0.917 1.906,0.167 1.906,0.167 2.083,0.167 true 2.667,6.583 2.667,6.74 true 2.833,6.135 1.99,6.5 1.99,6.5 1.865,6.5 true 2.833,5.667 1.99,5.302 1.99,5.302 1.865,5.302 true 2.927,5.344 2.927,4.833 2.927,4.833 2.667,4.833 true 2.021,1.25 2.26,1.5 2.26,1.5 2.344,1.5 true 2.042,3.094 2.292,3.333 2.292,3.333 2.375,3.333 true 0.542,1.479 1,1.802 0.458,0.323 10 false Hall IC 2.417,1.406 3.25,1.729 0.833,0.323 10 false Sensor Vane 1.438,5.208 1.917,5.531 0.479,0.323 10 false Hall IC 1.438,6.406 1.917,6.729 0.479,0.323 10 false Hall IC 2.135,0.073 3.083,0.396 0.948,0.323 10 false Magnetic Yoke 2.25,6.75 3.198,7.073 0.948,0.323 10 false Magnetic Yoke 2.167,4.76 2.688,5.083 0.521,0.323 10 false Magnet 3.521,5.521 3.917,5.802 0.396,0.281 10 false VTA1 4.354,5.677 4.688,5.958 0.333,0.281 10 false ECM 3.521,6.042 3.875,6.323 0.354,0.281 10 false VCS 3.531,6.333 3.969,6.615 0.438,0.281 10 false VTA2 3.542,6.635 3.854,6.917 0.313,0.281 10 false E2S 3.521,5.219 3.958,5.5 0.438,0.281 10 false VNVC 3.531,5.813 3.969,6.094 0.438,0.281 10 false VNE2 3.667,1.292 4.156,1.938 0.49,0.646 10 false Output Voltage 0.458,2.167 1.25,2.49 0.792,0.323 10 false Fully Closed 4.323,2.833 5.115,3.156 0.792,0.323 10 false Fully Closed 4.073,1.917 4.313,2.104 0.24,0.188 10 false 0.5 4.073,1.021 4.313,1.208 0.24,0.188 10 false 4.5 4.104,0.708 4.333,0.906 0.229,0.198 10 false (V) 2.5,2.177 3.219,2.5 0.719,0.323 10 false Fully Open 6.094,2.833 6.823,3.156 0.729,0.323 10 false Fully Open 2.417,3.25 3.25,3.573 0.833,0.323 10 false Sensor Vane 4.99,2.417 6.365,2.74 1.375,0.323 10 false Nozzle Vane Position 1.875,7.167 3.75,7.49 1.875,0.323 10 false Nozzle Vane Position Sensor




OPERATION


a.

Glow Plug Control

i.

When the ignition switch is turned off to ON*1 or the engine switch is turned on (START)*2, the ECM operates the glow plug relay to heat the glow plug assemblies rapidly. At that moment, the glow indicator light in the combination meter is illuminated to inform the driver that the glow plug assemblies are being heated.

*1: Models without entry and start system

*2: Models with entry and start system



ii.

When the engine starts and the starter signal is off, after-glow control is conducted. When the temperature of the glow plug assembly reaches a predetermined level during after-glow control, it is maintained at a nearly constant level using the self-temperature-controlling function of the glow plug assembly.

W127858E03
5.104,2.469 5.302,2.469 5.302,2.469 5.406,1.802 true 5.667,0.208 6.583,0.625 0.917,0.417 10 false Ignition Signal 5.667,0.594 6.583,1.01 0.917,0.417 10 false Starter Signal 5.677,0.948 7.031,1.51 1.354,0.563 10 false Engine Coolant Temp. Sensor 5.667,1.615 7.042,2.042 1.375,0.427 10 false Combination Meter 5.656,2.115 7.01,2.469 1.354,0.354 10 false - Glow Indicator Light 4.583,0.667 5,1.104 0.417,0.438 10 false ECM 4.198,2.406 5.125,2.76 0.927,0.354 10 false CAN (Bus 2) 3,0.635 3.51,0.979 0.51,0.344 10 false Battery 1.948,1.198 3.635,1.573 1.688,0.375 10 false Glow Plug Relay 0.26,2.25 1.583,2.635 1.323,0.385 10 false Glow Plug Assembly



b.

Diesel Throttle Control

i.

The opening of the diesel throttle valve is controlled by the ECM in accordance with the engine conditions. As a result, the noise that is generated during idling and deceleration, as well as the noise and vibrations that are generated when the engine is stopped, have been reduced and this control makes it possible to recirculate the exhaust gas in accordance with the driving conditions.

W102428E02
2.115,1 1.854,0.729 1.854,0.729 1.792,0.729 true 3.24,1.021 3.5,0.75 3.5,0.75 3.563,0.75 true 2.708,1.25 3.135,1.667 3.135,1.667 3.385,1.667 true 1.625,0.646 1.885,0.875 0.26,0.229 10 false *1 3.594,0.646 3.865,0.875 0.271,0.229 10 false *2 4.781,0.99 4.938,1.156 0.156,0.167 10 false *4 5.813,0.448 5.969,0.615 0.156,0.167 10 false *5 5.813,0.667 5.969,0.833 0.156,0.167 10 false *6 5.813,0.854 5.969,1.021 0.156,0.167 10 false *7 5.813,1.01 5.969,1.177 0.156,0.167 10 false *8 5.813,1.177 5.969,1.344 0.156,0.167 10 false *9 5.813,1.365 6.063,1.531 0.25,0.167 10 false *10 5.813,1.594 6.063,1.76 0.25,0.167 10 false *11 3.406,1.604 3.563,1.771 0.156,0.167 10 false *3

Text in Illustration
*1 Throttle Position Sensor *2 Throttle Control Motor
*3 Diesel Throttle Valve *4 ECM
*5 Engine Speed Signal *6 Vehicle Speed Signal
*7 Engine Coolant Temperature Signal *8 Intake Air Temperature Signal
*9 Accelerator Pedal Position *10 Intake Air Pressure Signal
*11 Ignition Signal - -



c.

Swirl Control

i.

The ECM determines the swirl control valve position based on the engine conditions (engine speed and accelerator pedal effort). Then, it switches the vacuum applied to the actuator diaphragm via the VSV, in order to open and close the swirl control valve.


ii.

In the low engine speed range, the ECM closes the swirl control valve to strengthen the swirl in the combustion chamber, thus promoting the mixture of fuel and air and stabilizing combustion.


iii.

In the middle engine speed range, the ECM opens the swirl control valve to the semi-open position.


iv.

In the high engine speed range, the ECM fully opens the swirl control valve.

W102258E05
1.969,2.979 1.969,3.406 1.969,3.406 1.635,3.406 true 2.01,1.708 1.542,2.729 1.542,2.729 1.344,2.729 true 1.25,0.75 1.625,0.75 1.625,0.75 1.625,1.698 true 1.448,1.323 1.448,0.76 true 5.573,0.74 6.708,1.531 1.135,0.792 10 false Accelerator Pedal Position Sensor 5.563,1.927 6.813,2.344 1.25,0.417 10 false Engine Coolant Temperature Sensor 5.573,2.667 6.979,3.375 1.406,0.708 10 false Intake Air Temperature Sensor 5.573,3.406 7.042,3.771 1.469,0.365 10 false Turbo Pressure Sensor 5.563,3.792 6.906,4.688 1.344,0.896 10 false Intake Mass Air Flow Meter Sub-assembly 3.385,2.885 4.115,3.26 0.729,0.375 10 false No. 1 VSV 2.76,4.24 3.552,4.615 0.792,0.375 10 false No. 2 VSV 5.573,1.531 6.667,1.875 1.094,0.344 10 false Engine Speed 2.635,0.729 3.583,1.094 0.948,0.365 10 false Vacuum Pump 0.115,2.073 1.594,2.438 1.479,0.365 10 false Combustion Chamber 0.167,2.625 1.406,2.99 1.24,0.365 10 false Swirl Control Valve 0.531,0.656 1.292,1.021 0.76,0.365 10 false Intake Port 1.073,3.313 1.667,3.677 0.594,0.365 10 false Actuator 4.521,2.385 4.906,2.75 0.385,0.365 10 false ECM



d.

Turbocharger Control

i.

The ECM calculates the optimal nozzle vane position in accordance with the driving conditions (engine speed, injection volume, atmospheric pressure, and engine coolant temperature etc.), and controls the nozzle vane position in accordance with this target nozzle vane position and the actual nozzle vane position signal provided by the nozzle vane position sensor.

W102259E12
3.542,0.948 3.823,0.219 3.823,0.219 4.104,0.219 true 0.917,1.552 1.135,2.083 1.135,2.083 1.24,2.083 true 0.781,1.375 0.729,1.219 0.729,1.219 0.646,1.219 true 4.438,2.229 5.26,3.271 0.823,1.042 10 false Atmospheric Pressure Sensor 0.094,1.125 0.615,2.563 0.521,1.438 10 false Nozzle Vane Position Sensor 1.271,1.99 1.917,2.385 0.646,0.396 10 false DC Motor 4.177,0.115 5.719,0.51 1.542,0.396 10 false Turbo Pressure Sensor 4.677,0.813 5.063,1.208 0.385,0.396 10 false ECM 5.625,0.74 7.052,1.156 1.427,0.417 10 false Crank Position Sensor 5.635,2.271 6.885,3 1.25,0.729 10 false Engine Coolant Temperature Sensor 5.635,3.021 7.083,3.667 1.448,0.646 10 false Intake Air Temperature Sensor 5.625,1.49 6.125,1.823 0.5,0.333 10 false Injector



e.

Starter Control (Models with Entry and Start System)

i.

When the driver pushes the engine switch once and the certification ECU (smart key ECU assembly) detects a start signal, the certification ECU (smart key ECU assembly) will output ACCD and STAR signals and begin cranking. Also, the driver can continue cranking for up to 30 seconds by pushing and holding the engine switch.


ii.

If the engine speed reaches approximately 800 rpm, the ECM will judge that the engine has started and will send a signal to the certification ECU (smart key ECU assembly) using CAN communication. The certification ECU (smart key ECU assembly) will then stop the operation of the starter.


iii.

If CAN communication is cut between the certification ECU (smart key ECU assembly) and the ECM, the certification ECU (smart key ECU assembly) will receive an engine speed signal (NE) directly from the ECM and will stop the operation of the starter.


iv.

This system will cut off the power current which activates the accessories while the engine is being cranked. This prevents the intermittent blinking of the accessory lights caused by the voltage instability that occurs during engine cranking.


v.

This system has the following protections:

·

The starter will not operate if the engine is operating normally.

·

If the engine switch is pushed and held, cranking will stop once the engine speed reaches a pre-determined level. This prevents the starter from over-revving.

·

If the engine does not start even after approximately 6 seconds of starter operation, the certification ECU (smart key ECU assembly) will cancel the starter relay output. Furthermore, if the engine does not start after the engine switch has been pushed and held and cranking has continued for 30 seconds, cranking will be canceled in order to protect the starter.

·

It will not be possible to operate the starter for 2 seconds after engine starting has failed and cranking has been canceled. This helps to protect the starter.

W100462E33
0.625,1.521 1.573,1.833 0.948,0.313 10 false Engine Switch 3.323,1.542 3.719,1.906 0.396,0.365 10 false ECM 4.063,1.292 5.219,2.052 1.156,0.76 10 false CAN (Bus 2) 1.979,2.219 2.74,2.552 0.76,0.333 10 false ACC Relay 4.542,4.99 5.052,5.635 0.51,0.646 10 false Starter Relay 1.594,5.156 2.719,5.542 1.125,0.385 10 false Starter Assembly 5.656,0.708 6.052,1.073 0.396,0.365 10 false SSW 5.646,1.031 6.906,1.969 1.26,0.938 10 false Certification ECU (Smart Key ECU Assembly) 5.656,1.99 6.052,2.354 0.396,0.365 10 false NE 5.656,2.51 6.281,2.74 0.625,0.229 10 false ACCD 5.656,2.781 6.281,3.146 0.625,0.365 10 false STAR 5.656,4.885 5.979,5.219 0.323,0.333 10 false STA 5.625,5.51 5.948,5.844 0.323,0.333 10 false STP 4.688,6.167 6.083,6.542 1.396,0.375 10 false Stop Light Signal*2 4.521,2.906 5.479,4.646 0.958,1.74 10 false Clutch Start Switch*1 or Park/Neutral Position Switch Assembly*2 0.427,6.385 2.948,6.719 2.521,0.333 10 false *2: Models with automatic transmission 0.427,6.052 2.865,6.375 2.438,0.323 10 false *1: Models with manual transmission

W100205E10
0.792,0.469 1.813,0.823 1.021,0.354 10 false Starter Signal 1.948,0.271 2.219,0.542 0.271,0.271 10 false On 1.948,1.208 2.219,1.479 0.271,0.271 10 false On 1.948,1.99 2.219,2.26 0.271,0.271 10 false On 1.948,0.667 2.25,0.938 0.302,0.271 10 false Off 1.948,1.625 2.25,1.896 0.302,0.271 10 false Off 1.948,2.385 2.25,2.656 0.302,0.271 10 false Off 0.958,1.396 1.813,1.708 0.854,0.313 10 false Starter Relay 0.698,2.198 1.813,2.51 1.115,0.313 10 false Accessory Power 0.885,3.208 2.188,3.854 1.302,0.646 10 false Engine Speed Signal (NE) 5.563,2.531 6.667,3.177 1.104,0.646 10 false Successful Starting of Engine 5.594,3.229 6.521,4.198 0.927,0.969 10 false Failed Starting of Engine 1.667,3.958 5.156,4.583 3.49,0.625 10 false ECM determines that the engine has started successfully when the engine speed is approximately 800 rpm.




f.

Fuel Pump Control (Models with Dual Fuel Tank)

i.

The supply pump assembly delivers fuel from the main fuel tank to the engine. Therefore, fuel in sub fuel tank needs to be transferred to the main fuel tank. In this system, the ECM operates the fuel pump to transfer the fuel from the sub fuel tank to the main fuel tank using the jet pump built into the fuel pump.

W102260E02
4.542,0.74 4.375,0.573 4.375,0.573 4.125,0.573 true 2.563,3.542 1.75,3.542 true 3.115,3.604 4.063,3.604 true 2.906,2.083 2.906,1.219 2.906,1.219 2.052,1.219 true 0.938,2.229 1.302,2.458 0.365,0.229 10 false ECM 5.104,0.813 5.583,1.042 0.479,0.229 10 false Engine 4.927,3.969 5.854,4.333 0.927,0.365 10 false Sub-fuel Tank 2.604,3.979 3.635,4.302 1.031,0.323 10 false Main Fuel Tank 1.188,1.125 2.031,2.021 0.844,0.896 10 false Fuel Filter for Fuel Pump 1.021,3.448 1.844,3.917 0.823,0.469 10 false Fuel Pump 4.115,3.51 4.521,4.365 0.406,0.854 10 false Jet Pump 2.604,0.458 4.125,0.823 1.521,0.365 10 false Supply Pump Assembly



g.

Engine Mount Control

i.

The ECM determines the idling state of the engine and the low speed state of the vehicle in accordance with the engine speed and the vehicle speed. Thus, the ECM controls the introduction of vacuum from the vacuum pump (for the engine) to the engine mount by turning the VSV on or off.


ii.

A hysteresis is provided for both the engine speed and the vehicle speed at the point in which the VSV switches from on to off.


iii.

While the engine is cranking, the VSV is off.

W102263E02
2.323,1.271 3.021,0.573 3.021,0.573 3.469,0.573 true 2.344,1.875 2.344,2.365 true 1.333,1.865 1.333,2.365 1.333,2.365 2.729,2.365 true 2.99,1.198 3.313,1.563 0.323,0.365 10 false VSV 4.063,0.99 4.427,1.354 0.365,0.365 10 false ECM 3.521,0.49 4.49,0.854 0.969,0.365 10 false Vacuum Pump 5.135,1 6.5,1.365 1.365,0.365 10 false Vehicle Speed Signal 5.135,1.635 6.5,2 1.365,0.365 10 false Engine Speed Signal 2.771,2.271 4.198,2.729 1.427,0.458 10 false Front Engine Mount 1.594,0.333 2.083,0.698 0.49,0.365 10 false Engine 2.99,5.333 3.406,5.76 0.417,0.427 10 false Idling 1.646,4.479 2.417,4.906 0.771,0.427 10 false Low Speed 5.281,5.125 6.25,5.49 0.969,0.365 10 false Engine Speed 5.292,3.146 5.948,3.51 0.656,0.365 10 false : VSV On 5.292,3.563 5.969,3.927 0.677,0.365 10 false : VSV Off 1.615,3 2.573,3.365 0.958,0.365 10 false Vehicle Speed


iv.

When the ECM determines that the engine speed is anything other than idle in accordance with the engine speed and the vehicle speed, it stops the introduction of vacuum into the engine mount by turning the VSV off.


v.

When no vacuum is introduced into the engine mount, the diaphragm does not move, so the No. 1 fluid passage remains closed. In this state, the fluid passes only through the No. 1 fluid passage in order to flow back and forth between the No. 1 and No. 2 fluid chambers.

W102264E03
3.99,1.781 4.469,1.313 4.469,1.313 4.74,1.313 true 3.563,1.813 2.76,1.615 2.76,1.615 2.458,1.615 true 3.938,2.094 5.146,2.094 true 3.333,1.604 2.552,0.823 2.552,0.823 2.448,0.823 true 4.802,1.229 6.177,1.938 1.375,0.708 10 false Flow of Fluid in No. 1 Fluid Passage 1.219,1.531 2.5,1.927 1.281,0.396 10 false Diaphragm Stopped 2.906,2.49 4.385,2.792 1.479,0.302 10 false No Vacuum Introduced 5.198,2 6.729,2.51 1.531,0.51 10 false No. 2 Fluid Chamber 1.135,0.719 2.51,1.042 1.375,0.323 10 false No. 1 Fluid Chamber 0.865,0.188 1.365,0.417 0.5,0.229 10 false : Fluid


vi.

When the ECM determines via the engine speed and the vehicle speed that the engine is idling, it turns the VSV on to introduce vacuum into the engine mount.


vii.

When a vacuum is introduced into the engine mount, it pulls the diaphragm down, causing the No. 2 fluid passage to open. As a result, a large volume of fluid flows back and forth between the No. 1 and No. 2 fluid chambers, thus minimizing the fluid resistance and softening the engine mount characteristics.

W102265E03
4.063,1.563 4.542,1.094 4.542,1.094 4.813,1.094 true 3.885,1.469 4.479,0.115 4.479,0.115 4.833,0.115 true 3.625,1.896 2.833,1.719 2.833,1.719 2.531,1.719 true 4.021,1.865 5.219,1.865 true 3.406,1.396 2.625,0.615 2.625,0.615 2.521,0.615 true 4.865,1.021 6.24,1.729 1.375,0.708 10 false Flow of Fluid in No. 1 Fluid Passage 4.906,0.031 6.281,0.74 1.375,0.708 10 false Flow of Fluid in No. 2 Fluid Passage 1.208,1.646 2.635,2.115 1.427,0.469 10 false Diaphragm Descends 3.052,2.49 4.302,2.792 1.25,0.302 10 false Vacuum Introduced 5.281,1.771 6.823,2.292 1.542,0.521 10 false No. 2 Fluid Chamber 1.229,0.521 2.604,0.844 1.375,0.323 10 false No. 1 Fluid Chamber 0.885,0.188 1.385,0.417 0.5,0.229 10 false : Fluid



h.

Drive Start Control

i.

When abnormal driver accelerator pedal and shift operations are detected, the system limits the engine output and informs the driver.

W136843E05
0.219,0.208 2.479,0.573 2.26,0.365 10 false Accelerator Pedal Sensor Assembly 0.771,1.5 1.823,1.906 1.052,0.406 10 false Steering Sensor 0.625,2.073 2.167,2.427 1.542,0.354 10 false Airbag ECU Assembly* 4.865,2.646 6.74,3.042 1.875,0.396 10 false Combination Meter Assembly 2.688,3.948 4.677,4.323 1.99,0.375 10 false Transmission Revolution Sensor 4.979,1.031 6.042,1.438 1.063,0.406 10 false Engine Output 3.542,1.708 3.938,2 0.396,0.292 10 false ECM 0.219,4.115 1.688,4.396 1.469,0.281 10 false *: Acceleration signal 0.531,4.448 2.24,4.719 1.708,0.271 10 false : CAN communication line 0.458,0.719 2.25,1.375 1.792,0.656 10 false Park/Neutral Position Switch Assembly 0.75,2.635 2.115,3.021 1.365,0.385 10 false Skid Control ECU

HINT:
·

The drive start control does not operate, when the TRC is canceled by VSC OFF switch.

·

The drive start control does not operate, when the L4 position is selected by 4WD switch.

·

The drive start control does not operate, when the center differential lock is locked by transfer position switch.

·

When the system is operating, even if the driver depresses and holds the accelerator pedal, engine output may increase on an uphill slope and decrease on a downhill slope. This behavior allows the system to restrict the vehicle speed and acceleration below the predetermined limit on slopes and is not a malfunction.




ii.

Control during Shift Operation

1.

Responds to shift operations with the accelerator pedal depressed.

2.

Changes the limit amount according to the shift operation pattern.

3.

Corrects engine output according to the road grade and steering angle.

(a)

Control when Starting Off from a Parked Position

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is changed from P to D/S, or P to R.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the engine output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift position is P or N.



W110518E20
3.615,0.927 3.792,0.771 3.792,0.771 3.99,0.771 true 5.021,1.427 5.146,1.219 5.146,1.219 5.396,1.219 true 5.021,2.323 5.146,2.115 5.146,2.115 5.396,2.115 true 1.563,0.208 2.51,0.542 0.948,0.333 10 false Shift Position 1.354,0.573 2.552,0.948 1.198,0.375 10 false Accelerator Pedal 2.844,0.229 3.073,0.458 0.229,0.229 10 false P 3.406,0.229 3.635,0.458 0.229,0.229 10 false D 2.781,0.573 3.104,0.823 0.323,0.25 10 false ON 4.042,0.698 4.896,1.01 0.854,0.313 10 false Control Start 1.615,1.583 2.573,2.052 0.958,0.469 10 false Engine Output 3.823,2.469 4.615,2.74 0.792,0.271 10 false Time 4.573,1.583 5.458,1.948 0.885,0.365 10 false Restricted 5.448,1.135 6.333,1.49 0.885,0.354 10 false w/o Control 5.448,2.021 6.24,2.406 0.792,0.385 10 false w/ Control

(b)

Control during Other Situations

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is changed from R to D/S, D/S to R, or N to R.

·

Accelerator opening angle is approximately 1/5 or higher.


Control Operation Restricts the engine output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift position is P or N.



W110519E17
3.573,0.927 3.771,0.771 3.771,0.771 3.979,0.771 true 5,1.406 5.156,1.24 5.156,1.24 5.344,1.24 true 4.927,2.198 5.083,2.031 5.083,2.031 5.271,2.031 true 1.615,0.198 2.573,0.594 0.958,0.396 10 false Shift Position 1.354,0.573 2.5,0.958 1.146,0.385 10 false Accelerator Pedal 4.063,0.708 4.927,1.104 0.865,0.396 10 false Control Start 2.844,0.229 3.052,0.458 0.208,0.229 10 false N 3.406,0.229 3.615,0.458 0.208,0.229 10 false R 2.781,0.573 3.083,0.792 0.302,0.219 10 false ON 1.698,1.604 2.625,2.052 0.927,0.448 10 false Engine Output 3.677,2.469 4.229,2.792 0.552,0.323 10 false Time 4.563,1.552 5.385,1.854 0.823,0.302 10 false Restricted 5.427,1.146 6.24,1.552 0.813,0.406 10 false w/o Control 5.333,1.958 6.229,2.333 0.896,0.375 10 false w/ Control

HINT:
·

The engine output restraint level differs in the above 2 situations.

·

During control while a shift operation is performed (from control start until the accelerator pedal is released), the system informs the driver of the control via the multi-information display. For details, see the METER / GAUGE / DISPLAY section.






iii.

Control during Reverse Operation

1.

Responds to excessive depression of the accelerator pedal while operating in reverse.

2.

Corrects engine output according to the road grade and steering angle.

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift position is R.

·

Accelerator pedal is depressed excessively.


Control Operation Restricts the engine output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift position is not R.



W110517E20
3.604,1.063 3.75,0.885 3.75,0.885 3.948,0.885 true 5.031,1.406 5.135,1.177 5.135,1.177 5.375,1.177 true 5.01,2.052 5.115,1.823 5.115,1.823 5.354,1.823 true 1.583,0.208 2.677,0.5 1.094,0.292 10 false Shift Position 1.302,0.573 2.49,0.927 1.188,0.354 10 false Accelerator Pedal 1.635,1.604 2.635,1.938 1,0.333 10 false Engine Output 3.802,2.49 4.458,2.76 0.656,0.271 10 false Time 4.542,1.5 5.281,1.771 0.74,0.271 10 false Restricted 5.438,1.104 6.281,1.458 0.844,0.354 10 false w/o Control 3.271,0.573 3.635,0.813 0.365,0.24 10 false ON 2.823,0.229 3.031,0.438 0.208,0.208 10 false R 4.01,0.802 4.969,1.115 0.958,0.313 10 false Control Start 5.438,1.729 6.26,2.115 0.823,0.385 10 false w/ Control