Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2017.08–2020.08
NM27T0E _52 Drivetrain _053611 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260142 AUTOMATIC TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with dynamic radar cruise control system

*2: Models with analog display type combination meter assembly

*3: Models with Optitron display type combination meter assembly

Torque Converter Clutch Assembly
·

Transmits the engine power to the transmission.

·

Increases engine torque.


Oil Pump Provides oil pressure necessary for the transmission operation.
No. 1 Clutch (C1) Connects the input shaft and the intermediate shaft.
No. 2 Clutch (C2) Connects the input shaft and the center planetary carrier.
No. 3 Clutch (C3) Connects the input shaft and the front sun gear.
No. 1 Brake (B1) Prevents the front planetary carrier from turning either clockwise or counterclockwise.
No. 2 Brake (B2) Prevents the front and center planetary ring gears from turning either clockwise or counterclockwise.
No. 3 Brake (B3) Prevents the outer race of F2 from turning either clockwise or counterclockwise.
No. 4 Brake (B4) Prevents the center planetary carrier and the rear planetary ring gear from turning either clockwise or counterclockwise.
No. 1 1-way Clutch (F1) Prevents the front planetary carrier from turning counterclockwise.
No. 2 1-way Clutch (F2) Prevents the front planetary sun gear from turning counterclockwise when B3 is operating.
No. 3 1-way Clutch (F3) Prevents the center planetary carrier and the rear planetary ring gear from turning counterclockwise.
Planetary Gears These gears change the route through which driving force is transmitted, in accordance with the operation of each clutch and brake, in order to increase or reduce the input and output speed.
Shift Solenoid Valve DSL (S1) Switches the 2-3 shift valve.
No. 3 transmission Solenoid Assembly (S2) Switches the 1-2 shift valve or 3-4 shift valve.
Shift Solenoid Valve S4 (SR) Switches the clutch apply control valve.
Shift Solenoid Valve (SL1)
·

Controls clutch pressure.

·

Controls accumulator back pressure.


Shift Solenoid Valve (SL2) Controls brake pressure.
Line Pressure Control Solenoid Assembly (SLT)
·

Controls line pressure.

·

Controls accumulator back pressure.


Lock-up Control Solenoid Assembly (SLU)
·

Controls lock-up clutch pressure.

·

Controls accumulator back pressure.


ATF Temperature Sensors Detects the ATF temperature.
Transmission Revolution Sensor (NT) Detects the input speed of the transmission.
Transmission Revolution Sensor (SP2) Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly Detects the shift lever position (P, R, N, D).
Transmission Control Switch
·

Detects that the shift lever is in S.

·

Detects the driver's shift-up and shift-down operations when the shift lever is in S.


2nd Start Switch (Pattern Select Switch Assembly) Sends a 2nd start mode signal to the TCM.
ECM
·

Controls engine output in response to a signal from the TCM.

·

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.


TCM
·

Controls each shift solenoid valve in response to a signal from each sensor and switch.

·

When the TCM detects a malfunction, it makes a diagnosis and memorizes the failed section.


4WD Control ECU Sends a drive mode signal to the TCM.
Air Conditioning Amplifier Assembly Sends a shift-up tardiness control signal to the ECM.
Driving Support ECU Assembly*1 Sends a shifting control request signal to the ECM.
Combination Meter Assembly Shift Display
·

Indicates the shift lever position.

·

Indicates to inform the driver of driving in D mode or S mode.

·

Indicates the shift range (S1 to S5).


MIL Illuminates or blinks to inform the driver when the ECM or TCM detects a malfunction.
2nd Start Indicator Light Illuminates when the driver selects the 2nd start mode.
ATF Temperature Warning Light*2 Warns the driver by lighting up when the ATF is at a high temperature.
Multi-information Display*3
·

Warns the driver by displaying a message when the ATF is at a high temperature.

·

Displays a Diagnostic Trouble Code (DTC).


Master Warning Light*3 Warns the driver by lighting up when a message is shown on the multi-information display.
Buzzer
·

Sounds when shift-down operation is rejected in S mode.

·

Warns the driver by sounding when a message is shown on the multi-information display.*2




SYSTEM CONTROL


Electronic Control of Automatic Transmission
Control Function
Shift Timing Control The TCM sends current to shift solenoid valves S1, S2 and/or SR based on signals from various sensors in order to shift the gears.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the TCM and the operating conditions of the transmission.
Clutch Pressure Optimal Control The shift solenoid valves SL1 and SLT minutely control the clutch pressure in accordance with the engine output and driving conditions of the transmission.
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to B1 brake and C1 clutch by actuating the shift solenoid valves SL1 and SL2 in accordance with the TCM signals.
Engine Torque Control Reduces the fuel injection volume temporarily to improve shift feeling while upshifts or downshifts occur.
N to D Squat Control When the shift lever is moved from N to D, the gear is temporarily engaged to the 2nd and then to the 1st to reduce vehicle squat.
Lock-up Timing Control The TCM sends current to the shift solenoid valve SLU based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control Controls the shift solenoid valve SLU, provides an intermediate mode for when the lock-up clutch is between on and off, and increases the operating range of the lock-up clutch to improve fuel economy.
Coast Downshift Control The TCM performs downshifts before fuel cut ends to prevent the engine speed from decreasing and maintain the fuel cut.
Artificial Intelligence-shift Control (AI-shift Control) Based on the signals from various sensors, the TCM determines the road conditions and the intention of the driver. Then, an appropriate shift pattern is automatically determined, thus improving driveability.
Multi-mode Automatic Transmission The TCM appropriately controls the automatic transmission in accordance with the range position selected while the shift lever is in S.

a.

Line Pressure Control

i.

In order to obtain a predetermined line pressure characteristic in accordance with each sensor signal, the TCM activates the shift solenoid valve SLT to regulate the throttle pressure.


ii.

This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.

X127688E04
3.146,3.135 4.281,4.51 1.135,1.375 10 false Line Pressure Control Solenoid Assembly (SLT) 1.073,2.938 1.771,4.354 0.698,1.417 10 false Primary Regulator Valve 0.5,0.271 1.469,0.625 0.969,0.354 10 false Line Pressure 0.25,2.25 0.656,2.615 0.406,0.365 10 false Pump 4.031,0.292 5.01,1.135 0.979,0.844 10 false Solenoid Valve Drive Signal 5.719,0.719 7.021,1.083 1.302,0.365 10 false Input Turbine Speed 5.74,1.104 6.885,1.469 1.146,0.365 10 false ATF Temperature 5.76,1.5 6.646,1.865 0.885,0.365 10 false Shift Position 5.771,1.896 6.677,2.26 0.906,0.365 10 false Gear Position 5.75,3.531 6.698,3.896 0.948,0.365 10 false Engine Speed 5.74,3.948 6.74,4.604 1,0.656 10 false Engine Coolant Temperature 1.813,0.51 2.427,1.458 0.615,0.948 10 false Fluid Pressure 2.75,1.438 3.281,1.802 0.531,0.365 10 false Current 5.719,2.74 6.854,3.469 1.135,0.729 10 false Accelerator Pedal Opening Angle 5.417,2.26 7.021,2.604 1.604,0.344 10 false CAN communication line 5.167,1.219 5.49,1.583 0.323,0.365 10 false TCM 5.167,3.083 5.5,3.448 0.333,0.365 10 false ECM



b.

Clutch Pressure Optimal Control

i.

The TCM monitors the signals from various types of sensors, such as the transmission revolution sensor (NT), allowing shift solenoid valves SL1 and SLT to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are achieved.

X102176E12
4.25,3.906 5.094,4.104 5.094,4.104 5.094,4.323 true 3.729,3.917 3.323,4.104 3.323,4.104 2.896,4.104 true 4.052,3.917 3.156,4.5 3.156,4.5 1.208,4.5 true 3.594,3.188 3.135,2.396 3.135,2.396 2.656,2.396 true 4.604,3.167 4.979,2.458 4.979,2.458 5.333,2.458 true 5.396,2.375 6.927,3.063 1.531,0.688 10 false Transmission Revolution Sensor (SP2) 4.292,4.313 5.927,4.667 1.635,0.354 10 false ATF Temperature Sensor 0.333,2.323 2.625,2.688 2.292,0.365 10 false Transmission Revolution Sensor (NT) 1.25,4.021 2.99,4.375 1.74,0.354 10 false Accumulator Control Valve 0.146,4.417 1.177,5.583 1.031,1.167 10 false Shift Solenoid Valve (SL1) and Line Pressure Control Solenoid Assembly (SLT) 5.813,0.646 6.177,1.167 0.365,0.521 10 false TCM 2.208,1.896 2.604,2.25 0.396,0.354 10 false Time 0.521,0.521 0.875,1.573 0.354,1.052 10 false Input Shaft rpm 1.094,1.458 2.875,1.813 1.781,0.354 10 false Practical rpm Change Ratio 1.917,0.583 2.75,1.156 0.833,0.573 10 false Target rpm Change Ratio 1.563,5.01 2.385,5.688 0.823,0.677 10 false Clutch/Brake Pressure 2.76,6.156 4.083,6.51 1.323,0.354 10 false Solenoid Drive Signal 6.323,6.135 6.719,6.49 0.396,0.354 10 false Time 4.719,5 5.156,6.031 0.438,1.031 10 false Output Shaft Torque



c.

Clutch to Clutch Pressure Control

i.

This control is used for shifting from 4th to 5th gear and from 5th to 4th gear.


ii.

The TCM actuates shift solenoid valves SL1 and SL2 in accordance with various signals. The output from these shift solenoid valves acts directly on control valves B1 and C1 in order to regulate the line pressure that acts on the B1 brake and C1 clutch.


iii.

As a result, high response and excellent shift characteristics have been achieved.

X127689E03
0.427,1.625 2.771,2 2.344,0.375 10 false Transmission Revolution Sensor (NT) 0.344,2 2.771,2.375 2.427,0.375 10 false Transmission Revolution Sensor (SP2) 0.76,2.354 2.76,2.698 2,0.344 10 false No. 1 ATF Temperature Sensor 0.49,0.281 2.781,0.656 2.292,0.375 10 false Engine Coolant Temperature Sensor 0.615,0.677 2.771,1.052 2.156,0.375 10 false Accelerator Pedal Position Sensor 0.594,3.208 2.417,3.583 1.823,0.375 10 false Shift Solenoid Valve (SL1) 5.25,3.208 7.125,3.583 1.875,0.375 10 false Shift Solenoid Valve (SL2) 2.563,3.865 3.885,4.24 1.323,0.375 10 false Clutch Control Valve 3.708,1.167 5.802,1.594 2.094,0.427 10 false CAN communication line 0.51,5.354 2.146,5.729 1.635,0.375 10 false Line Pressure 3.396,0.479 3.74,0.854 0.344,0.375 10 false ECM 3.396,1.979 3.74,2.354 0.344,0.375 10 false TCM 5.271,3.875 6.594,4.25 1.323,0.375 10 false Brake Control Valve



d.

Lock-up Timing Control

i.

The TCM operates the lock-up timing control in order to improve the fuel consumption performance in the top gear when the shift lever is in D or in the S5 or S4 range.

Lock-up Timing Control Operation
Gear Shift Lever Position or Shift Range
D, S5 S4
1st X X
2nd X X
3rd X X
4th X ○
5th ○ -

HINT:

○: Available

X: Does not operate

-: Not available




e.

Flex Lock-up Clutch Control

i.

In the low-to-mid-speed range, this flex lock-up clutch control regulates the shift solenoid valve SLU to provide an intermediate mode between the on and off operations of the lock-up clutch in order to improve the energy transmitting efficiency in this range. As a result, the operating range of the lock-up clutch has been increased and fuel economy has been improved. The flex lock-up clutch control operates in 3rd, 4th and 5th gears when the shift lever is in D or in the S5 range, and in 3rd and 4th gears when the shift lever is in the S4 range.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), the flex lock-up clutch control operates. Therefore, the fuel-cut area of the engine has been expanded and fuel economy has been improved.

X127690E04
2.021,1.635 2.365,1.635 2.365,1.635 2.583,1.854 true 2.031,3.656 1.865,3.656 1.865,3.656 2.073,4.354 true 1.448,5.156 1.823,5.156 1.823,5.156 2.063,4.844 true 3.25,5.792 3.625,5.792 3.625,5.792 3.969,4.677 true 3.469,6.208 3.844,6.208 3.844,6.208 4.083,5.406 true 4.615,6.177 4.302,6.177 4.302,6.177 4.427,5.375 true 4.99,5.802 4.75,5.802 4.75,5.802 4.625,5.375 true 5.667,1 5.51,1 5.51,1 5.354,1.802 true 6.01,1.854 5.823,1.854 5.823,1.854 5.708,1.781 true 2.729,1.042 3.385,1.042 3.385,1.042 3.604,0.49 true 2.083,3.573 3.896,4.208 1.813,0.635 10 false Engine Coolant Temperature Sensor 0.229,5.083 1.427,5.688 1.198,0.604 10 false Crankshaft Position Sensor 5.698,0.927 6.625,1.583 0.927,0.656 10 false Engine Speed Signal 4.583,1.417 5.021,2.094 0.438,0.677 10 false Engine Speed 2.646,0.229 2.979,0.573 0.333,0.344 10 false ECM 5.135,2.167 6.021,2.51 0.885,0.344 10 false Vehicle Speed 0.917,5.698 3.177,6.042 2.26,0.344 10 false Transmission Revolution Sensor (NT) 2.083,6.115 3.417,6.458 1.333,0.344 10 false Lock-up Control Valve 5.042,5.719 6.677,6.063 1.635,0.344 10 false ATF Temperature Sensor 4.677,6.094 6.229,6.781 1.552,0.688 10 false Lock-up Control Solenoid Assembly (SLU) 6.083,1.781 6.896,2.781 0.813,1 10 false Transmission Revolution Signal 5.417,3.656 5.813,4 0.396,0.344 10 false Time 4.563,3.135 5.021,3.438 0.458,0.302 10 false Current 5.99,2.958 6.531,3.802 0.542,0.844 10 false Linear Solenoid Signal 0.375,1.563 1.99,2.208 1.615,0.646 10 false Accelerator Pedal Position Sensor 4.323,0.229 4.646,0.573 0.323,0.344 10 false TCM 1.135,0.948 2.719,1.427 1.583,0.479 10 false CAN communication line

X102147E34
2.667,1.083 5.688,1.427 3.021,0.344 10 false : Lock-up operating range 0.271,0.323 3.292,0.667 3.021,0.344 10 false Flex Lock-up Operating Range 2.667,1.448 5.688,1.792 3.021,0.344 10 false : Flex lock-up operating range (acceleration) 2.646,1.781 5.667,2.125 3.021,0.344 10 false : Flex lock-up operating range (deceleration) 3.24,4.208 4.167,4.552 0.927,0.344 10 false Vehicle Speed 1.594,2.271 1.99,2.615 0.396,0.344 10 false Large 4.948,4.219 5.271,4.563 0.323,0.344 10 false High 0.865,2.969 2.042,3.646 1.177,0.677 10 false Accelerator Pedal Depressing Angle 0.563,4 1.75,4.677 1.188,0.677 10 false Accelerator Pedal is Released

Flex Lock-up Clutch Control Operation
Gear Shift Lever Position or Shift Range
D, S5 S4
1st X X
2nd X X
3rd ○* ○*
4th ○ ○*
5th ○ -

HINT:

○: Available

X: Does not operate

-: Not available

*: Flex lock-up clutch control operates during deceleration.




f.

Coast Downshift Control

i.

Downshift control is used when decelerating, allowing for low fuel consumption by extending fuel cut control as much as possible.


ii.

By performing flex lock-up control and downshift control at the same time when decelerating, a decrease of engine speed has been suppressed, while extending fuel cut control as much as possible without lowering the engine speed below the fuel cut recovery speed.


iii.

By expanding operating gears and widening operating areas through close-gear ratios, fuel efficiency has significantly been enhanced and drivability has been improved by optimizing deceleration force when controls are activated.

X127076E06
1.958,1.49 2.073,1.49 2.073,1.49 2.208,1.771 false 2.917,1.552 3.031,1.552 3.031,1.552 3.167,1.833 false 4.167,1.677 4.042,1.677 4.042,1.677 3.917,1.969 false 4.719,2.698 4.594,2.698 4.594,2.698 4.469,2.448 false 3.979,2.688 4.094,2.688 4.094,2.688 4.167,2.396 false 3.469,2.563 3.583,2.563 3.583,2.563 3.792,2.354 false 0.448,0.594 1.375,1.031 0.927,0.438 10 false Engine Speed 0.438,2 1.302,2.688 0.865,0.688 10 false Fuel Cut Return Speed 0.448,2.917 1.104,3.802 0.656,0.885 10 false Fuel Cut Duration 2.25,0.729 3.719,1.438 1.469,0.708 10 false Coast Downshifts Occur Earlier 1.542,1.375 2.021,1.688 0.479,0.313 10 false To 5th 2.469,1.448 2.938,1.823 0.469,0.375 10 false To 4th 4.229,1.583 4.813,1.906 0.583,0.323 10 false To 3th 4.99,2.99 5.5,3.323 0.51,0.333 10 false Time 3.146,3.427 4.24,3.802 1.094,0.375 10 false Extended Time 4.948,3.448 6.531,4.313 1.583,0.865 10 false Enhanced Fuel Efficiency Through Extended Fuel Cut Control 4.844,0.167 6.938,0.51 2.094,0.344 10 false : With coast downshift control 4.844,0.573 6.958,0.948 2.115,0.375 10 false : Without coast downshift control 4.76,2.594 5.344,2.927 0.583,0.333 10 false To 3th 3.563,2.573 4.031,2.948 0.469,0.375 10 false To 4th 3.042,2.458 3.51,2.854 0.469,0.396 10 false To 5th



g.

Artificial Intelligence-shift Control (AI-shift Control)

i.

The AI-shift control determines optimal transmission control based on input signals and automatically changes the shift pattern. As a result, a high caliber of transmission operation is achieved.


ii.

The AI-shift control includes a road condition support control and a driver's intention support control.


iii.

The AI-shift control is effected only with the shift lever in D, based on the accelerator pedal and brake operation data. The AI-shift control will be canceled when the shift lever is moved to a position other than D.

X100540E06
6.052,4.917 6.583,6.188 0.531,1.271 10 false Driver's Intention Support Control 6.083,2.667 6.667,4.042 0.583,1.375 10 false Road Condition Support Control 3.01,3.583 4.854,3.938 1.844,0.354 10 false : Actual acceleration 0.677,3.219 1.615,3.542 0.938,0.323 10 false - Brake Signal 0.667,2.823 1.646,3.177 0.979,0.354 10 false - Engine Speed 0.667,2.458 1.677,2.813 1.01,0.354 10 false - Vehicle Speed 0.875,0.708 2.146,1.125 1.271,0.417 10 false Input Signals 0.833,1.365 2.104,1.781 1.271,0.417 10 false Sensor Signal 0.625,1.792 1.833,2.458 1.208,0.667 10 false - Accelerator Pedal Depression Angle 0.625,4.198 1.844,4.563 1.219,0.365 10 false Calculated by ECM 0.594,4.51 1.875,4.865 1.281,0.354 10 false Vehicle Acceleration 2.656,1.177 4.271,1.531 1.615,0.354 10 false AI-shift Control 2.802,1.531 4.417,1.885 1.615,0.354 10 false Road Condition 3.042,1.885 4.896,2.24 1.854,0.354 10 false Uphill/Downhill Driving 3.531,2.281 5.281,2.635 1.75,0.354 10 false Estimating Grade 2.604,2.625 3.542,2.979 0.938,0.354 10 false Small 3.917,2.875 4.625,3.229 0.708,0.354 10 false Large 3.021,3.24 4.865,3.594 1.844,0.354 10 false : Criterion acceleration 2.854,4.302 4.333,4.656 1.479,0.354 10 false Driver's Intention 2.667,4.74 3.875,5.396 1.208,0.656 10 false - Accelerator Pedal Operation 2.667,5.427 3.927,5.781 1.26,0.354 10 false - Vehicle Condition 4.354,4.99 5.354,5.635 1,0.646 10 false Estimating Driver's Intention 6.104,0.75 7.031,1.719 0.927,0.969 10 false Basic Shift Pattern Control


iv.

Under road condition support control, the ECM or TCM identifies the throttle valve opening angle, the accelerator pedal opening angle and the vehicle speed to determine whether the vehicle is being driven uphill or downhill. To achieve an optimal drive force while driving uphill, this control prevents the transmission from upshifting to 4th or 5th gear. To achieve an optimal engine braking effect while driving downhill, this control automatically downshifts the transmission to 4th or 3rd gear.

X102181E04
5.917,3.771 6.875,4.156 0.958,0.385 10 false With Control 5.438,3.938 5.833,4.302 0.396,0.365 10 false 5th 4.75,3.938 5.094,4.302 0.344,0.365 10 false 4th 5.917,3.26 7.01,3.635 1.094,0.375 10 false Without Control 4.281,3.938 4.542,4.313 0.26,0.375 10 false 3rd 3.135,3.917 3.479,4.219 0.344,0.302 10 false 4th 3.927,3.417 4.25,3.708 0.323,0.292 10 false 5th 2.823,3.417 3.125,3.74 0.302,0.323 10 false 4th 2.417,3.417 2.719,3.719 0.302,0.302 10 false 5th 2.083,3.927 2.344,4.302 0.26,0.375 10 false 3rd 2.083,3.427 2.365,3.771 0.281,0.344 10 false 3rd 1.521,3.917 1.948,4.26 0.427,0.344 10 false 4th 1.76,3.417 2.063,3.75 0.302,0.333 10 false 5th 1.323,3.417 1.656,3.781 0.333,0.365 10 false 4th 0.708,3.917 1.073,4.302 0.365,0.385 10 false 5th 0.708,3.417 1.052,3.74 0.344,0.323 10 false 5th 4.719,1.198 5.854,1.615 1.135,0.417 10 false Brake Operating


v.

The driver's intention support control is estimated based on the accelerator pedal operation and vehicle condition, and a shift pattern that is well-suited to the driver is selected.



h.

Multi-mode Automatic Transmission

i.

A multi-mode automatic transmission is designed to allow the driver to switch the shift ranges (a multi-mode transmission is not for manually selecting single gears). After moving the shift lever to S, the driver can select the desired shift range by moving the shift lever to "+" (forwards) or "-" (backwards). Thus, the driver is able to shift gears with a manual-like feel.

X127691E04
0.688,0.208 2.531,0.583 1.844,0.375 10 false Combination Meter Assembly 5.656,1.281 6.583,1.979 0.927,0.698 10 false Transmission Control Switch 1.146,0.771 2.885,1.104 1.74,0.333 10 false CAN communication line 1.104,2.667 2.417,3.417 1.313,0.75 10 false Fuel Injection Timing Control Signal 3.271,2.823 4.969,3.802 1.698,0.979 10 false Fluid Pressure Control and Solenoid Valve Control Signal 4,2.073 5.458,2.448 1.458,0.375 10 false S Mode Position Signal 4.01,1.688 5.115,2.063 1.104,0.375 10 false Shift-down Signal 4.021,1.302 4.948,1.677 0.927,0.375 10 false Shift-up Signal 0.969,3.729 1.427,4.104 0.458,0.375 10 false Engine 3.104,1.49 3.438,1.865 0.333,0.375 10 false TCM 0.865,1.24 1.198,1.615 0.333,0.375 10 false ECM 2.76,3.958 3.615,4.333 0.854,0.375 10 false Transmission


ii.

The driver selects S mode by engaging the shift lever. At this time, the S4 range is selected (during AI-shift control, the shift range that has the currently controlled gear position as the maximum usable gear position will be displayed). Then, the shift range changes one at a time, as the driver moves the shift lever to "+" (forwards) or "-" (backwards).


iii.

Under this control, the TCM effects optimal shift control within the usable gear position that the driver has selected. As with an ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.


iv.

Holding the shift lever to "+" (forwards) in S will change the shift range to the S5 range regardless of shift range (S1 to S4).

X133241E01
2.354,3.188 2.667,3.385 0.313,0.198 10 false *a 4,1.573 4.313,1.771 0.313,0.198 10 false *b 5.115,2.99 5.427,3.188 0.313,0.198 10 false *d 4.615,1.979 4.927,2.177 0.313,0.198 10 false *c 4.625,2.594 4.938,2.792 0.313,0.198 10 false *c 4.625,3.26 4.938,3.458 0.313,0.198 10 false *c 4.667,3.927 4.979,4.125 0.313,0.198 10 false *c

Text in Illustration
*a Shift Pattern *b Transition of Shift Range Position
*c Moves shift lever to "+" (forwards) or "-" (backwards). *d Holding shift lever to "+" (forwards).
V100143

Default Shift Range - -

Usable Gear Chart
Shift Range Shift Range Indicator Display Usable Gear
S5 5 5th←→4th←→3rd←→2nd←→1st
S4 4 4th←→3rd←→2nd←→1st
S3 3 3rd←→2nd←→1st
S2 2 2nd←→1st
S1 1 1st


v.

When the shift lever is in S, the S mode indicator is shown in the combination meter assembly. The shift range indicator indicates the state of the shift range position that the driver has selected.


vi.

When the vehicle is being driven at a prescribed speed or higher, any attempt to shift to a lower range by operating the shift lever will not be executed, in order to protect the automatic transmission. In this case, the TCM sounds the buzzer in the combination meter assembly twice to alert the driver.




FUNCTION


a.

Shift Lock System

i.

The shift lock system prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON and the brake pedal is depressed. This prevents the vehicle from starting off suddenly.


ii.

The shift lock system is controlled by the shift lock control ECU sub-assembly and the system has a shift lock function and key interlock function*.

*: Models without entry and start system


iii.

The key interlock function prevents the key from being pulled out after the ignition switch has been turned off, unless the shift lever has been moved to P. Thus, the driver is urged to park the vehicle with the shift lever in P.


iv.

A shift lock release button, which manually overrides the shift lock mechanism, is used.

·

Models with Entry and Start System

X127059E05
0.427,0.323 2.344,0.708 1.917,0.385 10 false Stop Light Switch Assembly 0.385,1.063 2.188,1.635 1.802,0.573 10 false Certification ECU (Smart Key ECU Assembly) 0.313,2.167 2.542,2.5 2.229,0.333 10 false Engine Switch (Push Start Switch) 5.521,0.396 6.146,0.729 0.625,0.333 10 false Solenoid 5.302,1.135 6.76,1.479 1.458,0.344 10 false P Detection Switch 2.823,0.594 4.26,1.229 1.438,0.635 10 false Shift Lock Control ECU Sub-assembly 5.281,1.771 6.521,2.115 1.24,0.344 10 false Shift Lock Solenoid


·

Models without Entry and Start System

X127060E04
0.479,0.229 2.281,0.604 1.802,0.375 10 false Stop Light Switch Assembly 0.583,0.948 2.208,1.292 1.625,0.344 10 false Ignition Switch Assembly 5.521,0.281 6.115,0.677 0.594,0.396 10 false Solenoid 5.208,0.979 6.542,1.354 1.333,0.375 10 false P Detection Switch 2.854,0.417 4.302,1.052 1.448,0.635 10 false Shift Lock Control ECU Sub-assembly 5.115,2.229 6.708,2.583 1.594,0.354 10 false Key Interlock Solenoid 5.198,1.604 6.531,1.979 1.333,0.375 10 false Shift Lock Solenoid



v.

The shift lock control ECU sub-assembly uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and ignition switch. Upon receiving these signals, the shift lock control ECU sub-assembly turns on the shift lock solenoid and key interlock solenoid in order to release the shift lock and key interlock.

X127063E01
0.25,0.594 2.542,0.792 2.292,0.198 10 false Ignition Switch 0.25,1.469 2.542,1.667 2.292,0.198 10 false Stop Light Switch 0.25,2.177 2.542,2.375 2.292,0.198 10 false P Detection Switch 0.25,2.885 2.542,3.083 2.292,0.198 10 false Shift Lock Solenoid 0.25,3.583 2.542,3.781 2.292,0.198 10 false Key Interlock Solenoid* 2,0.583 2.542,0.917 0.542,0.333 10 false ACC 2,0.26 2.542,0.594 0.542,0.333 10 false IG 2,0.906 2.542,1.24 0.542,0.333 10 false OFF 2,1.302 2.542,1.635 0.542,0.333 10 false On 2,1.604 2.542,1.938 0.542,0.333 10 false Off 2,2.01 2.542,2.344 0.542,0.333 10 false On 2,2.323 2.542,2.656 0.542,0.333 10 false Off 2,2.719 2.542,3.052 0.542,0.333 10 false On 2,3.042 2.542,3.375 0.542,0.333 10 false Off 2,3.427 2.542,3.76 0.542,0.333 10 false On 2,3.76 2.542,4.094 0.542,0.333 10 false Off 0.271,4.365 3.688,4.667 3.417,0.302 10 false *: Models without smart entry and start system



b.

Shift Pattern Select System

i.

The shift pattern select system enables the driver to use a 2nd start switch (pattern select switch assembly to select the 2nd start mode which allows the vehicle to start off in the 2nd gear, thus making it easy for the vehicle to start off on snowy, sandy or muddy terrain.


ii.

When the 2nd start mode is selected while the shift lever is in D or in the S5, S4, S3 or S2 range, the vehicle can start in the 2nd gear. After a start, if the shift lever is in D or in the S5, S4 or S3 range, transmission will shift up automatically into 3rd, 4th or overdrive gears in the normal manner. If the shift lever is in the S2 range, the transmission will continue to operate in the 2nd gear.




CONSTRUCTION


a.

ATF Filling Procedures

i.

An ATF filling procedure is used in order to improve the accuracy of the ATF level when the transmission is being repaired or replaced. As a result, the oil filler tube and the oil level gauge used in the conventional automatic transmission have been discontinued, eliminating the need to inspect the fluid level as a part of routine maintenance. For details about the ATF filling procedures, refer to the corresponding Repair Manual for this model.


ii.

This filling procedure uses a refill plug, overflow plug, No. 2 ATF temperature sensor, and shift position indicator D.


iii.

ATF filling procedures are different between the models with an air-cooled type ATF cooler and the models without an air-cooled type ATF cooler.

X102190E03
4.521,2.604 4.323,3.229 4.323,3.229 3.865,3.229 true 4.865,2.458 5.063,3.24 5.063,3.24 5.51,3.24 true 1.5,1.823 1.729,2.167 0.229,0.344 10 false *1 3.688,3.146 3.917,3.49 0.229,0.344 10 false *2 5.552,3.115 5.781,3.458 0.229,0.344 10 false *a

Text in Illustration
*1 Refill Plug *2 Overflow Plug
*a Proper Level - -



b.

Torque Converter Clutch Assembly

i.

A compact, lightweight and high-capacity torque converter clutch assembly is used. The torque converter clutch supports lock-up clutch control, thus improving fuel economy.

X133370E01
2.198,0.635 2.958,0.635 true 2.198,1.313 3.354,1.313 true 3.917,0.698 4.917,0.698 true 3.719,1.458 4.917,1.458 true 2.167,1.948 3.375,1.948 true 2,0.542 2.313,0.74 0.313,0.198 10 false *1 2,1.219 2.313,1.417 0.313,0.198 10 false *3 1.99,1.854 2.302,2.052 0.313,0.198 10 false *5 5.01,1.365 5.323,1.563 0.313,0.198 10 false *4 5,0.604 5.313,0.802 0.313,0.198 10 false *2

Text in Illustration
*1 Lock-up Clutch *2 Pump Impeller
*3 Turbine Runner *4 Stator
*5 1-way Clutch - -



c.

Oil Pump

i.

The oil pump is operated by the torque converter clutch assembly. It lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control. The front oil pump drive gear is continually driven by the engine via the pump impeller. The pump has sufficient capacity to supply the necessary fluid pressure throughout all speed ranges, as well as in reverse.

X102192E04
2.052,2.927 2.052,3.375 true 3.396,2.365 3.396,3.396 true 5.417,2.167 5.417,3.396 true 4.625,1.771 4.625,3.396 true 3.917,2.125 3.917,3.385 true 2.719,3.021 2.719,3.385 true 2.688,3.448 2.844,3.625 0.156,0.177 10 false *2 3.323,3.448 3.479,3.625 0.156,0.177 10 false *3 3.854,3.438 4.01,3.615 0.156,0.177 10 false *4 4.573,3.448 4.729,3.625 0.156,0.177 10 false *5 5.365,3.438 5.521,3.615 0.156,0.177 10 false *6 1.979,3.448 2.135,3.625 0.156,0.177 10 false *1

Text in Illustration
*1 Front Oil Pump Body Sub-assembly *2 O-ring
*3 Front Oil Pump Driven Gear *4 Front Oil Pump Drive Gear
*5 Stator Shaft Assembly *6 Oil Pump Cover



d.

Planetary Gear Unit

i.

The gear train consists of three multi-plate clutches, four multi-plate brakes, three 1-way clutches, and three sets of planetary gears each consisting of a sun gear, a pinion gear and a ring gear.

X133371E01
3.635,1.354 3.646,0.281 true 2.708,1.396 1.833,0.76 1.833,0.76 1.833,0.49 true 2.958,1.521 2.083,0.667 2.083,0.667 2.083,0.271 true 3.229,1.688 2.667,0.833 2.667,0.833 2.667,0.313 true 3.26,1.344 3.177,0.677 3.177,0.677 3.177,0.344 true 4,1.5 4.083,0.583 4.083,0.583 4.083,0.313 true 4.479,1.438 4.563,0.615 4.563,0.615 4.563,0.302 true 4.823,1.865 5.063,0.656 5.063,0.656 5.063,0.344 true 2.896,1.365 2.333,0.771 2.333,0.771 2.333,0.5 true 3.375,1.615 2.917,1 2.917,1 2.917,0.5 true 3.583,1.479 3.417,1.063 3.417,1.063 3.417,0.458 true 4.24,1.615 4.354,0.75 4.354,0.75 4.354,0.479 true 4.583,1.531 4.792,0.781 4.792,0.781 4.792,0.51 true 1.563,1.875 1.563,0.292 true 3.875,1.563 3.885,0.49 true 5.25,1.844 5.354,1 5.354,1 5.333,0.49 true 1.469,0.083 1.688,0.302 0.219,0.219 10 false *1 2.031,0.083 2.25,0.302 0.219,0.219 10 false *3 2.583,0.083 2.802,0.302 0.219,0.219 10 false *5 3.083,0.083 3.302,0.302 0.219,0.219 10 false *7 3.563,0.083 3.781,0.302 0.219,0.219 10 false *9 3.948,0.083 4.167,0.302 0.219,0.219 10 false *11 4.958,0.083 5.177,0.302 0.219,0.219 10 false *15 4.417,0.083 4.635,0.302 0.219,0.219 10 false *13 1.75,0.281 1.969,0.5 0.219,0.219 10 false *2 2.281,0.281 2.5,0.5 0.219,0.219 10 false *4 2.833,0.281 3.052,0.5 0.219,0.219 10 false *6 3.333,0.281 3.552,0.5 0.219,0.219 10 false *8 3.76,0.313 3.979,0.531 0.219,0.219 10 false *10 4.198,0.281 4.417,0.5 0.219,0.219 10 false *12 4.667,0.281 4.885,0.5 0.219,0.219 10 false *14 5.25,0.281 5.469,0.5 0.219,0.219 10 false *16

Text in Illustration (Models with 1GR-FE Engine:)
*1 Input Shaft *2 No. 2 Clutch (C2)
*3 No. 1 Clutch (C1) *4 No. 3 Clutch (C3)
*5 No. 2 1-way Clutch (F2) *6 No. 1 1-way Clutch (F1)
*7 No. 3 Brake (B3) *8 Front Planetary Gear Assembly
*9 No. 1 Brake (B1) *10 Center Planetary Gear Assembly
*11 No. 2 Brake (B2) *12 No. 3 1-way Clutch (F3)
*13 No. 4 Brake (B4) *14 Rear Planetary Gear Assembly
*15 Intermediate Shaft *16 Output Shaft

X102194E03
0.802,1.906 0.802,2.469 true 6.24,1.906 6.24,2.469 true 1.99,1.927 1.99,2.469 true 4.646,2.083 4.646,2.469 true 5.563,2.083 5.563,2.469 true 3.615,2.135 3.615,2.469 true 3.552,2.479 3.708,2.656 0.156,0.177 10 false *3 0.75,2.479 0.906,2.656 0.156,0.177 10 false *1 6.188,2.49 6.344,2.667 0.156,0.177 10 false *6 1.917,2.479 2.073,2.656 0.156,0.177 10 false *2 4.604,2.479 4.76,2.656 0.156,0.177 10 false *4 5.531,2.479 5.688,2.656 0.156,0.177 10 false *5

Text in Illustration
*1 Input Shaft *2 Intermediate Shaft
*3 Front Planetary Gear Assembly *4 Center Planetary Gear Assembly
*5 Rear Planetary Gear Assembly *6 Output Shaft



e.

Centrifugal Fluid Pressure Canceling Mechanism

i.

The centrifugal fluid pressure canceling mechanism is used on the C1, C2 and C3 clutches that are applied when shifting 2nd-3rd, 3rd-4th, and 4th-5th.


ii.

Clutch shifting operation is affected not only by the valve body controlling fluid pressure but also by centrifugal fluid pressure that is present due to fluid in the clutch piston oil pressure chamber. The centrifugal fluid pressure canceling mechanism uses chamber B to reduce the affect applied to chamber A. As a result, smooth shifting with excellent response has been achieved.

X102195E03
2.073,1.813 1.781,2.875 1.781,2.875 1.781,3.24 true 1.635,1.729 0.719,2.667 0.719,2.667 0.719,3.24 true 1.885,1.969 1.219,2.76 1.219,2.76 1.219,3.24 true 1.5,1.479 0.656,0.854 0.656,0.854 0.656,0.427 true 1.698,1.615 1.229,0.729 1.229,0.729 1.229,0.427 true 1.719,1.458 1.781,0.802 1.781,0.802 1.781,0.438 true 2.063,1.385 2.333,0.677 2.333,0.677 2.333,0.438 true 2.375,1.354 2.896,0.698 2.896,0.698 2.896,0.417 true 2.792,1.333 3.427,0.771 3.427,0.771 3.427,0.417 true 2.875,1.719 3.448,2.813 3.448,2.813 3.448,3.24 true 2.729,2.229 2.896,2.896 2.896,2.896 2.896,3.24 true 2.417,2.208 2.333,2.927 2.333,2.927 2.333,3.26 true 2.802,0.24 3.01,0.417 0.208,0.177 10 false *5 3.354,0.24 3.563,0.417 0.208,0.177 10 false *6 2.26,0.24 2.469,0.417 0.208,0.177 10 false *4 1.708,0.26 1.917,0.438 0.208,0.177 10 false *3 1.156,0.24 1.365,0.417 0.208,0.177 10 false *2 0.594,0.229 0.802,0.406 0.208,0.177 10 false *1 2.802,3.281 3.115,3.458 0.313,0.177 10 false *11 3.354,3.281 3.656,3.458 0.302,0.177 10 false *12 2.26,3.292 2.552,3.469 0.292,0.177 10 false *10 1.708,3.281 1.917,3.458 0.208,0.177 10 false *9 1.156,3.281 1.365,3.458 0.208,0.177 10 false *8 0.615,3.281 0.823,3.458 0.208,0.177 10 false *7

Text in Illustration (Models with 1GR-FE Engine:)
*1 Chamber B (for C3) *2 Chamber A (for C2)
*3 Piston (for C3) *4 Piston (for C2)
*5 No. 2 Clutch (C2) *6 No. 3 Clutch (C3)
*7 Chamber A (for C3) *8 Chamber B (for C2)
*9 Chamber A (for C1) *10 Piston (for C1)
*11 Chamber B (for C1) *12 No. 1 Clutch (C1)


iii.

Chamber B is filled by fluid supplied to the shaft for lubrication. As a result of filling chamber B, the same amount of fluid pressure is present on both sides of the piston due to centrifugal force. This cancels the effects of fluid pressure on the piston caused by centrifugal force. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and highly responsive and smooth shifting characteristics are achieved.

U116711E12
3.802,0.302 3.969,0.302 3.969,0.302 3.969,0.635 true 3.729,1.5 3.552,1.5 3.552,1.5 3.552,1.167 true 2.719,0.438 3,0.438 3,0.438 3,1.313 true 1.135,1.26 1.594,1.26 true 1.75,2.646 2.25,2.646 2.25,2.646 2.25,2.365 false 4.74,3.521 6.552,4.354 1.813,0.833 10 false Target fluid pressure (original clutch pressure) 2.292,3.542 4.313,4.375 2.021,0.833 10 false Centrifugal fluid pressure applied chamber B 5.063,1.719 6.688,2.583 1.625,0.865 10 false : Centrifugal fluid pressure applied to chamber B 5.063,1.063 6.688,1.781 1.625,0.719 10 false : Centrifugal fluid pressure applied to chamber A 5.042,0.448 6.75,0.917 1.708,0.469 10 false : Target fluid pressure 3.333,0.198 3.875,0.531 0.542,0.333 10 false Clutch 3.792,1.396 4.333,1.802 0.542,0.406 10 false Piston 0.906,0.323 2.719,1.094 1.813,0.771 10 false Chamber B (Centrifugal Fluid Pressure Chamber) 0.302,1.167 1.115,2.542 0.813,1.375 10 false Chamber A (Piston Fluid Pressure Chamber) 0.667,2.552 1.708,3.219 1.042,0.667 10 false Fluid Pressure Applied to Piston 2.844,2.698 3.667,3.083 0.823,0.385 10 false Shaft Side 0.573,3.521 1.813,4.344 1.24,0.823 10 false Fluid pressure applied to piston



f.

Transmission Valve Body Assembly

i.

The transmission valve body assembly consists of the upper (No. 1 and No. 2) and lower valve bodies and 7 shift solenoid valves.

X102196E05
0.865,1.427 0.625,0.667 0.625,0.667 0.49,0.667 true 1.573,1.333 1.354,0.688 1.354,0.688 1.188,0.688 true 2.74,1.063 2.604,0.688 2.604,0.688 2.406,0.688 true 3.271,1.042 3.406,0.667 3.406,0.667 3.604,0.667 true 4.656,1.354 4.875,0.667 4.875,0.667 5.073,0.667 true 5.042,1.938 6.25,1.333 6.25,1.333 6.448,1.333 true 5.458,2.052 6.271,1.76 6.271,1.76 6.469,1.76 true 1.896,2.938 1.5,3.302 1.5,3.302 1.24,3.302 true 5.333,2.229 6.469,2.229 true 5.833,3.271 6.469,3.271 true 5.365,3.583 6.469,3.583 true 4.833,3.938 6.469,3.938 true 6.531,1.229 6.74,1.406 0.208,0.177 10 false *6 5.115,0.594 5.323,0.771 0.208,0.177 10 false *5 3.656,0.573 3.865,0.75 0.208,0.177 10 false *4 6.521,2.125 6.729,2.302 0.208,0.177 10 false *6 2.24,0.594 2.448,0.771 0.208,0.177 10 false *3 1.031,0.594 1.24,0.771 0.208,0.177 10 false *2 1.063,3.177 1.313,3.354 0.25,0.177 10 false *8 0.281,0.563 0.49,0.74 0.208,0.177 10 false *1 6.521,1.667 6.729,1.844 0.208,0.177 10 false *7 6.521,3.167 6.76,3.344 0.24,0.177 10 false *9 6.521,3.479 6.771,3.656 0.25,0.177 10 false *10 6.521,3.854 6.771,4.031 0.25,0.177 10 false *11

Text in Illustration
*1 Line Pressure Control Solenoid Assembly (SLT) *2 Shift Solenoid Valve (SL1)
*3 Shift Solenoid Valve DSL (S1) *4 Transmission Solenoid Assembly No. 3 (S2)
*5 No. 2 Upper Valve Body *6 Plate
*7 No. 1 Upper Valve Body *8 Lower Valve Body
*9 Shift Solenoid Valve S4 (SR) *10 Lock-up Control Solenoid Assembly (SLU)
*11 Shift Solenoid Valve (SL2) - -

X102197E05
2.021,0.302 2.021,1.135 true 1.615,0.292 1.615,0.865 true 3.188,0.313 3.188,1.26 true 3.427,0.302 3.427,1.448 true 3.958,0.323 3.958,1.698 true 4.677,0.323 4.677,1.229 true 4.896,0.313 4.896,1.313 true 5.396,0.302 5.396,1.302 true 1.865,2.458 1.865,3.365 true 2.354,2.521 2.354,3.396 true 3.188,2.427 3.188,3.396 true 3.646,2.646 3.646,3.396 true 4.281,2.635 4.281,3.385 true 1.813,3.417 1.969,3.594 0.156,0.177 10 false *9 3.115,0.125 3.271,0.302 0.156,0.177 10 false *3 3.365,0.115 3.521,0.292 0.156,0.177 10 false *4 3.875,0.115 4.031,0.292 0.156,0.177 10 false *5 4.615,0.125 4.771,0.302 0.156,0.177 10 false *6 2.281,3.417 2.51,3.594 0.229,0.177 10 false *10 1.948,0.125 2.104,0.302 0.156,0.177 10 false *2 1.531,0.104 1.688,0.281 0.156,0.177 10 false *1 4.844,0.125 5,0.302 0.156,0.177 10 false *7 5.344,0.125 5.5,0.302 0.156,0.177 10 false *8 3.115,3.427 3.344,3.604 0.229,0.177 10 false *11 3.583,3.427 3.813,3.604 0.229,0.177 10 false *12 4.198,3.427 4.427,3.604 0.229,0.177 10 false *13

Text in Illustration
*1 No. 1 Upper Valve Body *2 B1 Accumulator
*3 Clutch Lock Valve *4 Solenoid Modulator Valve
*5 3-4 Shift Valve *6 2-3 Shift Valve
*7 1-2 Shift Valve *8 B1 Apply Control Valve
*9 Secondary Regulator Valve *10 Lock-up Relay Valve
*11 Lock-up Control Valve *12 C3 Check Valve
*13 Brake Control Valve - -

X102198E03
2.688,0.427 2.688,1 true 4.427,2.594 4.427,3.281 true 2.615,0.229 2.823,0.448 0.208,0.219 10 false *1 4.375,3.281 4.625,3.573 0.25,0.292 10 false *2

Text in Illustration
*1 No. 2 Upper Valve Body *2 Coast Brake Relay Valve

X102199E05
1.688,0.406 1.688,0.708 true 2.156,0.385 2.156,1.302 true 3.49,0.396 3.49,1.563 true 4.219,0.385 4.219,1.438 true 3.979,2.563 3.979,3.333 true 3.281,2.25 3.281,3.365 true 1.917,2.323 1.917,3.333 true 1.625,0.208 1.781,0.385 0.156,0.177 10 false *1 2.094,0.208 2.25,0.385 0.156,0.177 10 false *2 3.417,0.208 3.573,0.385 0.156,0.177 10 false *3 4.156,0.208 4.313,0.385 0.156,0.177 10 false *4 3.927,3.354 4.083,3.531 0.156,0.177 10 false *7 3.219,3.354 3.375,3.531 0.156,0.177 10 false *6 1.844,3.354 2,3.531 0.156,0.177 10 false *5

Text in Illustration
*1 Lower Valve Body *2 Primary Regulator Valve
*3 Clutch Apply Control Valve *4 Sequence Valve
*5 SLT Damper *6 Clutch Control Valve
*7 Accumulator Control Valve - -



g.

Shift Solenoid Valves S1, S2 and SR

i.

The shift solenoid valve DSL (S1) and shift solenoid valve S4 (SR) are 3-way solenoid valves.


ii.

A filter is provided at the tip of the solenoid valve to further improve operational reliability.

X102200E02
2.865,1.073 2.708,1.365 2.708,1.365 2.385,1.365 true 3.948,1.438 3.833,1.615 3.833,1.615 3.625,1.615 true 3.406,0.313 3.604,0.531 0.198,0.219 10 false *c 2.208,1.25 2.417,1.5 0.208,0.25 10 false *2 2.385,0.875 2.594,1.104 0.208,0.229 10 false *a 2.958,1.323 3.177,1.531 0.219,0.208 10 false *b 3.448,1.5 3.635,1.708 0.188,0.208 10 false *1

Text in Illustration
*1 Shift Solenoid Valve DSL (S1) *2 Filter
*a Line Pressure *b Control Pressure
*c Drain - -

X102201E02
2.917,1.063 2.76,1.354 2.76,1.354 2.417,1.354 true 3.969,1.427 3.854,1.604 3.854,1.604 3.646,1.604 true 3.458,0.313 3.646,0.542 0.188,0.229 10 false *c 2.25,1.24 2.469,1.49 0.219,0.25 10 false *2 2.448,0.865 2.635,1.094 0.188,0.229 10 false *a 3.021,1.333 3.219,1.573 0.198,0.24 10 false *b 3.479,1.49 3.667,1.698 0.188,0.208 10 false *1

Text in Illustration
*1 Shift Solenoid Valve S4 (SR) *2 Filter
*a Line Pressure *b Control Pressure
*c Drain - -


iii.

The transmission solenoid assembly No. 3 (S2) uses a 2-way solenoid valve.

X102202E02
2.958,1.052 2.802,1.344 2.802,1.344 2.479,1.344 true 3.927,1.458 3.813,1.625 3.813,1.625 3.604,1.625 true 3.219,0.229 3.406,0.448 0.188,0.219 10 false *b 2.302,1.229 2.49,1.458 0.188,0.229 10 false *2 2.521,0.875 2.719,1.125 0.198,0.25 10 false *a 3.438,1.51 3.635,1.719 0.198,0.208 10 false *1

Text in Illustration
*1 No. 3 transmission Solenoid Assembly (S2) *2 Filter
*a Line Pressure *b Control Pressure

Function of Shift Solenoid Valves S1, S2 and SR
Shift Solenoid Valve Function
S1 Switches the 2-3 shift valve.
S2 Switches the 1-2 shift valve and the 3-4 shift valve.
SR Switches the clutch apply control valve.



h.

Shift Solenoid Valves SL1, SL2, SLT and SLU

i.

In order to provide a hydraulic pressure that is proportional to the current that flows to the solenoid coil, the shift solenoid valves SL1 and SL2 linearly control the clutch pressure based on the signals they receive from the TCM.

X102203E04
2.188,0.229 2,0.229 2,0.229 2,0.583 true 3.208,0.24 2.927,0.24 2.927,0.24 2.927,0.583 true 1.229,0.219 1.563,0.219 1.563,0.219 1.646,0.781 true 4.302,0.156 4.906,0.969 0.604,0.813 10 false Hydraulic Pressure 5.875,1.313 6.635,1.677 0.76,0.365 10 false Current 0.438,0.104 1.271,0.49 0.833,0.385 10 false Spool Valve 2.229,0.135 2.792,0.427 0.563,0.292 10 false Sleeve 3.25,0.135 4.198,0.479 0.948,0.344 10 false Solenoid Coil 1.365,1.385 3.708,1.719 2.344,0.333 10 false Shift Solenoid Valves (SL1, SL2)


ii.

In order to provide a hydraulic pressure that is proportional to the current that flows to the solenoid coil, the line pressure control solenoid assembly (SLT) linearly controls the line pressure based on the signals it receives from the TCM.

X102204E03
2.083,0.208 1.896,0.208 1.896,0.208 1.896,0.76 true 3.198,0.219 2.917,0.219 2.917,0.219 2.917,0.719 true 1.24,0.208 1.615,0.208 1.615,0.208 1.615,0.885 true 4.313,0.167 4.917,0.771 0.604,0.604 10 false Hydraulic Pressure 5.906,1.323 6.417,1.604 0.51,0.281 10 false Current 0.458,0.125 1.229,0.406 0.771,0.281 10 false Spool Valve 2.104,0.104 2.552,0.385 0.448,0.281 10 false Sleeve 3.24,0.115 4.188,0.396 0.948,0.281 10 false Solenoid Coil 0.771,1.365 3.969,1.708 3.198,0.344 10 false Line Pressure Control Solenoid Assembly (SLT)


iii.

In order to provide a hydraulic pressure that is proportional to the current that flows to the solenoid coil, the lock-up control solenoid assembly (SLU) linearly controls the lock-up clutch engagement pressure based on the signals it receives from the TCM.

X102205E06
3.208,0.208 2.917,0.208 2.917,0.208 2.917,0.74 true 2.042,0.24 1.854,0.24 1.854,0.24 1.854,0.813 true 1.25,0.219 1.5,0.219 1.5,0.219 1.74,0.948 true 4.292,0.167 4.917,0.76 0.625,0.594 10 false Hydraulic Pressure 5.906,1.333 6.406,1.615 0.5,0.281 10 false Current 3.271,0.125 4.219,0.406 0.948,0.281 10 false Solenoid Coil 0.479,0.135 1.25,0.417 0.771,0.281 10 false Spool Valve 2.083,0.156 2.531,0.438 0.448,0.281 10 false Sleeve 1.031,1.396 3.729,1.74 2.698,0.344 10 false Lock-up Control Solenoid Assembly (SLU)

Function of Shift Solenoid Valves SL1, SL2, SLT and SLU
Shift Solenoid Valve Function
SL1
·

C1 clutch pressure control

·

Accumulator back pressure control


SL2 B1, B2 and B4 brake pressure control
SLT
·

Line pressure control

·

Accumulator back pressure control


SLU
·

Lock-up clutch pressure control

·

Accumulator back pressure control





i.

ATF Temperature Sensor

i.

The No. 1 ATF temperature sensor (THO1) is used for hydraulic pressure control. This sensor is used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.


ii.

The No. 2 ATF temperature sensor (THO2) is used as a basis for modifying the ECT shift timing control when the ATF temperature is high. It is also used for the ATF temperature warning light and the ATF temperature warning message.

X102206E03
3.042,1.719 3.51,0.521 3.51,0.521 4.01,0.521 true 3.01,2.344 3.51,3.344 3.51,3.344 4.01,3.344 true 4.042,0.406 4.25,0.646 0.208,0.24 10 false *1 4.042,3.24 4.26,3.458 0.219,0.219 10 false *2 1.427,1.76 1.646,2.021 0.219,0.26 10 false *a

Text in Illustration
*1 No. 1 ATF Temperature Sensor *2 No. 2 ATF Temperature Sensor
*a Front - -



j.

Transmission Revolution Sensors

i.

This automatic transmission uses a transmission revolution sensor (for NT signal) and a transmission revolution sensor (for SP2 signal). Thus, the TCM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions.


ii.

These speed sensors are the pick-up coil type.


iii.

The transmission revolution sensor (for NT signal) detects the input speed of the transmission. The reverse clutch piston sub-assembly is used as the timing rotor for this sensor.


iv.

The transmission revolution sensor (for SP2 signal) detects the speed of the output shaft. The parking lock gear on the rear planetary gear is used as the timing rotor for this sensor.

X102207E03
3.125,0.76 3.125,1.563 true 4.146,0.771 4.146,1.292 true 4.5,1.688 4.5,2.99 true 3.49,2.229 3.49,3 true 4.719,1.625 5.354,2.365 5.354,2.365 5.354,3 true 3.063,0.563 3.281,0.76 0.219,0.198 10 false *1 4.073,0.573 4.292,0.771 0.219,0.198 10 false *2 4.448,3 4.698,3.25 0.25,0.25 10 false *4 5.313,3 5.552,3.271 0.24,0.271 10 false *5 3.438,3.01 3.667,3.292 0.229,0.281 10 false *3

Text in Illustration
*1 Reverse Clutch Piston Sub-assembly *2 Transmission Revolution Sensor (SP2)
*3 Transmission Revolution Sensor (NT) *4 Rear Planetary Gear
*5 Parking Lock Gear - -



k.

Park/Neutral Position Switch Assembly and Transmission Control Switch

i.

The TCM and ECM use the park/neutral position switch assembly and the transmission control switch to detect the shift lever position.


ii.

The park/neutral position switch assembly sends the P, R, N, D and NSW signals to the TCM and the D and NSW signals to the ECM. The TCM also send signals to the shift position indicator "P, R, N, and D" in the combination meter assembly via CAN.


iii.

The transmission control switch is installed inside the transmission floor shift assembly to detect the S mode position and to inform the TCM. The TCM turn on the S mode indicator in the combination meter assembly.


iv.

The transmission control switch detects whether the shift lever is in D or S, and detects the operating conditions of the shift lever ["+" (forwards) or "-" (backwards)] if the S mode is selected, and sends signals to the TCM. At this time, the TCM turn on the shift range indicator in the combination meter assembly via CAN for the selected shift range.

X102209E04
4.99,6.24 6.844,6.625 1.854,0.385 10 false CAN communication line 6,2.542 6.427,2.885 0.427,0.344 10 false TCM 3.615,6.063 4.042,6.406 0.427,0.344 10 false ECM 5.385,1.458 5.813,1.802 0.427,0.344 10 false P 5.177,1.104 5.604,1.448 0.427,0.344 10 false NSW 5.198,0.427 5.625,0.771 0.427,0.344 10 false STA 5.385,2.167 5.813,2.51 0.427,0.344 10 false N 5.385,1.813 5.813,2.156 0.427,0.344 10 false R 2.396,1.448 2.823,1.792 0.427,0.344 10 false PL 1.146,1.104 1.573,1.448 0.427,0.344 10 false L 1.073,2.531 1.5,2.875 0.427,0.344 10 false RB 1.115,3.833 1.542,4.177 0.427,0.344 10 false IG 2.406,1.083 2.833,1.427 0.427,0.344 10 false B 2.406,2.135 2.833,2.479 0.427,0.344 10 false NL 5.385,2.552 5.813,2.896 0.427,0.344 10 false D 3.76,5.625 4.188,5.969 0.427,0.344 10 false NSW 3.198,5.635 3.625,5.979 0.427,0.344 10 false STA 4.344,5.615 4.771,5.958 0.427,0.344 10 false D 2.406,2.51 2.833,2.854 0.427,0.344 10 false DL 2.406,1.802 2.833,2.146 0.427,0.344 10 false RL 0.031,0.979 0.635,1.667 0.604,0.688 10 false To Starter Relay 0.49,5.969 1.531,6.656 1.042,0.688 10 false Combination Meter Assembly 0.438,2.417 0.865,2.76 0.427,0.344 10 false +B 1.229,2.833 2.573,3.458 1.344,0.625 10 false Park/Neutral Position Switch Assembly 1.188,4.917 2.531,5.542 1.344,0.625 10 false Transmission Control Switch 2.427,4.167 2.854,4.51 0.427,0.344 10 false SFTU 2.417,3.823 2.844,4.167 0.427,0.344 10 false S 2.427,4.552 2.854,4.896 0.427,0.344 10 false SFTD 0.417,3.719 0.844,4.063 0.427,0.344 10 false +B 5.125,4.177 5.552,4.521 0.427,0.344 10 false SFTU 5.135,4.552 5.563,4.896 0.427,0.344 10 false SFTD 5.375,3.823 5.802,4.167 0.427,0.344 10 false S



l.

Shift Control Mechanism

i.

A gate type shift lever that uses a transmission control cable is used.


ii.

The shift control mechanism consists of a transmission floor shift assembly and a transmission control cable assembly.

X138056E01
2.833,2 1.5,2 1.5,2 1.5,1.167 true 3.083,0.667 3.667,0.417 true 3.583,3.25 3.917,3.75 true 1.427,1.021 1.74,1.219 0.313,0.198 10 false *1 3.667,0.313 3.979,0.51 0.313,0.198 10 false *2 3.896,3.76 4.208,3.958 0.313,0.198 10 false *3 5.99,3.521 6.302,3.719 0.313,0.198 10 false *a

Text in Illustration
*1 Transmission Floor Shift Assembly *2 Shift Lever Knob
*3 Transmission Control Cable Assembly - -
*a Shift Pattern - -




OPERATION


a.

Transmission Power Flow

Operating Condition
Shift Lever or Gear Range Position Gear Position Shift Solenoid Valve Clutch Brake 1-way Clutch
S1 S2 SR SL1 SL2 SLU C1 C2 C3 B1 B2 B3 B4 F1 F2 F3
P Park On Off Off Off On Off - - - - - - - - - -
R* Reverse On Off Off Off On Off - - ○ (○) - - ○ ○ - -
N Neutral On Off Off Off On Off - - - - - - - - - -
D, S5 1st On Off Off Off On Off ○ - - - - - - - - ○
2nd On On Off Off On Off ○ - - - - ○ - ○ ○ -
3rd Off On Off Off On Off ○ - ○ - - ● - ○ - -
4th* Off Off Off Off On Off ○ ○ ● - - ● - - - -
5th* Off Off On On Off On - ○ ○ ○ - ● - - - -
S4 1st On Off Off Off On Off ○ - - - - - - - - ○
2nd On On Off Off On Off ○ - - - - ○ - ○ ○ -
3rd Off On Off Off On Off ○ - ○ - - ● - ○ - -
4th* Off Off Off Off On On ○ ○ ● - - ● - - - -
S3 1st On Off Off Off On Off ○ - - - - - - - - ○
2nd On On Off Off On Off ○ - - - - ○ - ○ ○ -
3rd* Off On Off Off Off Off ○ - ○ (○) - ● - ○ - -
S2 1st On Off Off Off On Off ○ - - - - - - - - ○
2nd* On On On Off Off Off ○ - - - (○) ○ - ○ ○ -
S1 1st* On Off Off Off Off Off ○ - - - - - (○) - - ○

HINT:

○: Operates

●: Operates but is not related to power transmission

(○): Operates during engine braking

-: Does not operate

*: Engine braking occurs


i.

1st Gear (Shift Lever in D or in S5, S4, S3 or S2 Range)

X102211

Text in Illustration
V100143

Operates - -


ii.

2nd Gear (Shift Lever in D or in S5, S4 or S3 Range)

X102212

Text in Illustration
V100143

Operates - -


iii.

3rd Gear (Shift Lever in D or in S5 or S4 Range)

X102213

Text in Illustration
V100143

Operates - -


iv.

4th Gear (Shift Lever in D or in S5 or S4 Range)

X102214

Text in Illustration
V100143

Operates
V100144

Operates but is not related to power transmission


v.

5th Gear (Shift Lever in D or in S5 Range)

X102215

Text in Illustration
V100143

Operates
V100144

Operates but is not related to power transmission


vi.

1st Gear (Shift Lever in S1 Range)

X102216

Text in Illustration
V100143

Operates - -


vii.

2nd Gear (Shift Lever in S2 Range)

X102217

Text in Illustration
V100143

Operates - -


viii.

3rd Gear (Shift Lever in S3 Range)

X102218

Text in Illustration
V100143

Operates
V100144

Operates but is not related to power transmission


ix.

Reverse Gear (Shift Lever in R)

X102219

Text in Illustration
V100143

Operates
V100145

Operates during engine braking




FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a solenoid.

Fail-safe Control List
Malfunction Part Function
Transmission Revolution Sensor (NT)
·

During a transmission revolution sensor (NT) malfunction, shift control is effected based on the transmission revolution sensor (SP2) signal.

·

During a transmission revolution sensor (NT) malfunction, upshifting to 5th, AI-shift and flex lock-up clutch control are prohibited.


Transmission Revolution Sensor (SP2)
·

During a transmission revolution sensor (SP2) malfunction, shift control is effected based on the transmission revolution sensor (NT) signal.

·

During a transmission revolution sensor (SP2) malfunction, upshifting to 5th, AI-shift and flex lock-up clutch control are prohibited.


No. 1 ATF Temperature Sensor (THO1) During a No. 1 ATF temperature sensor malfunction, upshifting to 5th and flex lock-up clutch control are prohibited.
Shift Solenoid Valves S1, S2 and SR
·

When one of the shift solenoid valves listed left malfunctions, current to the failed shift solenoid valve is cut off.

·

Shift control is changed to a fail-safe mode to shift gears using the normal shift solenoid valves to allow continued driving.


Shift Solenoid Valves SL1 and SL2 During a shift solenoid valve SL1 or SL2 malfunction, upshifting to 5th and flex lock-up clutch control are prohibited.
Line Pressure Control Solenoid Assembly (SLT) During a line pressure control solenoid assembly (SLT) malfunction, the current to the shift solenoid valve is stopped. Because this stops line pressure optimal control, the shift shock will increase. However, shifting is effected based on normal clutch pressure control.
Lock-up Control Solenoid Assembly (SLU) During a lock-up control solenoid assembly (SLU) malfunction, the current to the shift solenoid valve is stopped. Because this stops lock-up control and flex lock-up control, fuel economy decreases.



DIAGNOSIS


a.

When the TCM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the TCM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The TCM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions.


c.

The DTCs can be read by connecting an Global TechStream (GTS) to the DLC3.


d.

For details, refer to the Repair Manual.