Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › FOUR WHEEL DRIVE CONTROL SYSTEM › 2017.08–2020.08
NM27T0E _52 Drivetrain _053617 VF4BM TRANSFER / 4WD / AWD _0260148 FOUR WHEEL DRIVE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

VF4BM TRANSFER / 4WD / AWD  FOUR WHEEL DRIVE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Transfer Shift Actuator Assembly H-L Shift Motor Switches the transfer gear ratio between high and low in accordance with signals from the 4WD control ECU.
H-L Limit Switch Detects the position of the H-L shift motor and transmits a signal to the 4WD control ECU.
Center Differential Lock Shift Motor Switches the center differential between free and lock in accordance with signals from the 4WD control ECU.
Center Differential Lock Limit Switch Detects the position of the center differential lock shift motor and transmits a signal to the 4WD control ECU.
Center Differential Lock Position Switch Detects the lock position of the center differential and transmits a signal to the 4WD control ECU and so on.
Transfer Position Switch Switches the drive mode and transmits a signal to the 4WD control ECU.
Center Differential Lock Switch*1 Switches the center differential between free and lock and transmits a signal to the 4WD control ECU.
Clutch Start Switch Assembly*2 Detects that the clutch pedal is completely depressed and transmits a signal to the 4WD control ECU.
4WD Control ECU Controls each shift motor in response to a signal from each switch.
ECM
·

Transmits a shift position signal to the 4WD control ECU via CAN.*3

·

Detects the center differential lock position switch signal.*4


TCM*5 Transmits a shift position signal to the ECM via CAN.
Combination Meter Assembly 4LO Indicator Light
·

Blinks while switching the transfer gear ratio between high and low, and turns on when in low.

·

Blinks when the switching conditions are not met while switching the transfer gear ratio between high and low.


Center Differential Lock Indicator Light
·

Blinks while switching the center differential between free and lock, and turns on when in lock.

·

Blinks when the switching conditions are not met while switching the center differential between free and lock.


VSC OFF Indicator Light*6 Turns on in accordance with the drive mode when VSC function is not operating.
Multi-information Display*7 Displays the status of the center differential lock operation.
Buzzer Sounds when the switching conditions are not met while switching the drive mode.

*1: Models with 1GR-FE, 1GD-FTV or 1KD-FTV engine

*2: Models with manual transmission

*3: Models with automatic transmission

*4: Models with 2TR-FE engine

*5: Models with 1KD-FTV engine and automatic transmission

*6: Models with VSC

*7: Models with Optitron display type combination meter assembly



OPERATING CONDITION


a.

4 Drive Mode (Models with 1GR-FE, 1GD-FTV or 1KD-FTV Engine)

i.

The drive mode switching pattern of the 4WD system is as shown in the illustration below:

X102268E05
3.25,0.688 4.031,1.052 0.781,0.365 10 false Pattern E 2.167,0.833 2.667,1.188 0.5,0.354 10 false H4F 4.74,0.833 5.219,1.188 0.479,0.354 10 false L4F 2.208,2.563 2.75,2.906 0.542,0.344 10 false H4L 4.76,2.563 5.271,2.896 0.51,0.333 10 false L4L 3.281,1.115 4.031,1.5 0.75,0.385 10 false Pattern F 2.49,1.656 3.313,2.031 0.823,0.375 10 false Pattern B 1.469,1.656 2.167,2.042 0.698,0.385 10 false Pattern A 5.052,1.604 5.885,1.958 0.833,0.354 10 false Pattern D 4.021,1.625 4.729,1.979 0.708,0.354 10 false Pattern C 3.271,2.469 4.063,2.823 0.792,0.354 10 false Pattern G 3.292,2.854 4.094,3.198 0.802,0.344 10 false Pattern H 0.104,0.063 2.76,0.49 2.656,0.427 10 false 4 Drive Mode Switching Pattern 0.354,3.219 3.896,3.583 3.542,0.365 10 false H4F: High speed 4WD and center differential Free 0.396,3.969 3.76,4.344 3.365,0.375 10 false L4F: Low speed 4WD and center differential Free 0.375,3.594 3.823,3.969 3.448,0.375 10 false H4L: High speed 4WD and center differential Lock 0.396,4.344 3.833,4.729 3.438,0.385 10 false L4L: Low speed 4WD and center differential Lock


ii.

The center differential can be switched between free and lock (switching patterns A to D) when the vehicle is running. However, the center differential should not be switched from free to lock when the vehicle is turning or the tires are spinning.


iii.

On the models with manual transmission, the transfer gear ratio can be switched between high and low (switching patterns E to H) only when the vehicle is stationary and the clutch pedal is being depressed.


iv.

On the models with automatic transmission, the transfer gear ratio can be switched between high and low (switching patterns E to H) only when the vehicle is stationary and the shift lever is in N.


v.

TRC or VSC function in the brake control system may be stopped, depending on the drive mode. For details, see the Brake Control/Dynamic Control Systems section.



b.

3 Drive Mode (Models with 2TR-FE or 5L-E Engine)

i.

The drive mode switching pattern of the 4WD system is as shown in the illustration below:

X102269E03
2.01,0.74 2.823,1.094 0.813,0.354 10 false Pattern A 0.917,0.833 1.469,1.188 0.552,0.354 10 false H4F 3.479,0.844 4.052,1.219 0.573,0.375 10 false H4L 6.052,0.844 6.615,1.198 0.563,0.354 10 false L4L 2.031,1.135 2.865,1.51 0.833,0.375 10 false Pattern B 4.594,0.74 5.375,1.094 0.781,0.354 10 false Pattern C 4.615,1.135 5.448,1.531 0.833,0.396 10 false Pattern D 0.417,1.573 3.979,1.938 3.563,0.365 10 false H4F: High speed 4WD and center differential Free 0.417,1.927 3.906,2.292 3.49,0.365 10 false H4L: High speed 4WD and center differential Lock 0.094,0 2.531,0.438 2.438,0.438 10 false 3 Drive Mode Switching Pattern 0.417,2.281 3.771,2.667 3.354,0.385 10 false L4L: Low speed 4WD and center differential Lock


ii.

The center differential can be switched between free and lock (switching patterns A and B) when the vehicle is running. However, the center differential should not be switched from free to lock when the vehicle is turning or the tires are spinning.


iii.

On the models with manual transmission, the transfer gear ratio can be switched between high and low (switching patterns C and D) only when the vehicle is stationary and the clutch pedal is being depressed.


iv.

On the models with automatic transmission, the transfer gear ratio can be switched between high and low (switching patterns C and D) only when the vehicle is stationary and the shift lever is in N.




CONSTRUCTION


a.

Transfer Assembly

i.

A planetary gear unit is used in the reduction mechanism.


ii.

The center differential uses a TORSEN* LSD. As a result, this LSD ensures the proper torque distribution during acceleration and high-speed driving.

HINT:

*: TORSEN is a registered trademark of JTEKT Corporation.


X102231E09
0.896,1.604 1.396,1.604 1.396,1.604 1.948,2.177 true 1.521,3.656 2.396,3.656 2.396,3.656 3.208,3.01 true 1.844,4.281 2.563,4.281 2.563,4.281 3.563,2.99 true 2.271,4.979 2.646,4.979 2.646,4.979 3.375,3.917 true 5.229,4.938 4.802,4.938 4.802,4.938 4.125,3.427 true 6.01,4.167 5.531,4.167 5.531,4.167 5.177,3.406 true 2.125,0.781 2.563,0.781 2.563,0.781 2.708,1.729 true 4.323,0.802 3.844,0.802 3.844,0.802 3.375,1.906 true 5.896,1.208 5.385,1.208 5.385,1.208 4.958,2.313 true 0.719,1.51 1,1.74 0.281,0.229 10 false *1 1.948,0.688 2.146,0.917 0.198,0.229 10 false *2 4.365,0.688 4.594,0.906 0.229,0.219 10 false *3 5.938,1.125 6.281,1.406 0.344,0.281 10 false *4 1.344,3.563 1.552,3.823 0.208,0.26 10 false *5 1.656,4.177 1.875,4.406 0.219,0.229 10 false *6 2.104,4.896 2.313,5.125 0.208,0.229 10 false *7 6.031,4.063 6.26,4.24 0.229,0.177 10 false *9 5.271,4.854 5.583,5.104 0.313,0.25 10 false *8

Text in Illustration
*1 Transfer Input Shaft *2 Transfer Low Planetary Gear Assembly
*3 Center Differential *4 Transfer Rear Output Shaft
*5 No. 2 Transfer Gear Shift Fork *6 Center Differential Lock Fork Sub-assembly
*7 Transfer Front Output Shaft *8 Transfer Front Drive Chain
*9 Transfer Shift Actuator Assembly - -



b.

Transfer Low Planetary Gear Assembly

i.

A transfer low planetary gear assembly is used on the planetary gear unit to switch the transfer gear ratio between high and low.


ii.

The transfer low planetary gear assembly consists of the planetary sun gear, 4 planetary pinion gears, planetary ring gear, and planetary carrier.


iii.

The planetary sun gear is integrated with the transfer input shaft. A transfer clutch hub spline piece is fitted to the rear of the planetary sun gear.


iv.

4 planetary pinion gears are fitted to the planetary carrier. Each pinion gear shaft is fixed to the planetary carrier. A transfer low planetary spline piece is fitted to the rear of the planetary carrier.


v.

The planetary ring gear is fixed to the front transfer case and its internal teeth mesh with the planetary pinion gears.


vi.

In this planetary gear unit, the power transmission route is switched in accordance with the movement of the transfer high and low clutch sleeve. The input power from the transfer input shaft is transmitted to the center differential case via the transfer high and low clutch sleeve.

X102232E01
2.118,0.891 2.634,0.891 2.634,0.891 2.863,1.627 false 4.042,0.733 3.652,0.733 3.652,0.733 3.591,1.569 false 4.861,0.817 4.437,0.817 4.437,0.817 3.811,1.487 false 5.877,3.292 5.409,3.292 5.409,3.292 4.857,2.421 false 5.023,3.843 4.519,3.843 4.519,3.843 3.848,2.823 false 0.805,2.114 0.961,2.296 0.156,0.181 10 *1 0.978,2.185 1.447,2.185 1.447,2.185 1.896,2.902 false 1.19,1.369 1.346,1.551 0.156,0.181 10 *2 1.96,0.819 2.116,1.001 0.156,0.181 10 *3 4.06,0.668 4.216,0.849 0.156,0.181 10 *4 4.884,0.749 5.040,0.930 0.156,0.181 10 *5 5.53,1.346 5.686,1.527 0.156,0.181 10 *6 5.729,1.882 5.885,2.063 0.156,0.181 10 *7 5.888,3.213 6.044,3.394 0.156,0.181 10 *8 5.024,3.771 5.180,3.952 0.156,0.181 10 *9 1.359,1.443 2.033,1.443 2.033,1.443 3.264,2.215 false 4.285,1.428 5.513,1.428 false 3.752,1.945 5.711,1.945 false

Text in Illustration
*1 Transfer Input Shaft *2 Planetary Sun Gear
*3 Planetary Ring Gear *4 Planetary Carrier
*5 Transfer Low Planetary Spline Piece *6 Transfer High and Low Clutch Sleeve
*7 Transfer Clutch Hub Spline Piece *8 Center Differential Case
*9 Planetary Pinion Gear - -



c.

Center Differential

i.

The center differential uses a TORSEN* LSD. Also, a mechanism is used to switch the center differential between free and lock.


ii.

The TORSEN* LSD is a torque-sensing LSD. It generates a limited-differential torque in proportion to the drive torque, and instantly changes the front and rear torque distribution.

HINT:

*: TORSEN is a registered trademark of JTEKT Corporation.



iii.

The torque distribution during straightline driving is 40/60 (front/rear), which is helpful for an appropriate steering response during the initial stage of a turn. During the acceleration stage of a turn, the torque distribution increases in the rear wheels.


iv.

This center differential consists of a center differential case, sun gear, ring gear, coupling, 8 pinion gears, clutch plates, and planetary carrier.


v.

The drive torque is input to the center differential case.


vi.

The center differential case is connected with the planetary carrier.


vii.

The sun gear is connected to the front driver sprocket (in the front wheel output side) through the transfer clutch hub and transfer front drive spline piece.


viii.

The ring gear is connected to the transfer rear output shaft (in the rear wheel output side) through the coupling.


ix.

The center differential is switched between free and lock in accordance with the movement of the front drive clutch sleeve.

X102233E02
3.979,0.802 3.656,0.802 3.656,0.802 3.427,1.427 true 4.958,0.771 4.646,0.771 4.646,0.771 3.49,1.927 true 5.844,1.229 5.125,1.229 5.125,1.229 4.479,1.813 true 5.594,2.479 5.052,2.479 5.052,2.479 3.969,2.198 true 5.333,2.771 4.833,2.771 4.833,2.771 3.458,2.385 true 4.625,3.354 4.188,3.354 4.188,3.354 3.198,2.75 true 4.094,3.604 3.427,3.604 3.427,3.604 3.083,2.719 true 3.302,3.875 2.969,3.875 2.969,3.875 2.969,2.76 true 1.188,3.531 1.5,3.531 1.5,3.531 1.792,3.042 true 1.25,1.365 1.708,1.365 1.708,1.365 2.417,1.906 true 2.438,0.844 2.771,0.844 2.771,0.844 2.958,1.979 true 1.771,1.063 2.156,1.063 2.156,1.063 2.74,2.031 true 4.958,3.073 4.406,3.073 4.406,3.073 3.302,2.427 true 1.938,3.917 2.292,3.917 2.292,3.917 2.979,2.281 true 1.01,2.229 2.646,2.229 true 1.094,1.292 1.25,1.469 0.156,0.177 10 false *1 4.021,0.698 4.177,0.875 0.156,0.177 10 false *4 2.26,0.75 2.417,0.927 0.156,0.177 10 false *3 1.604,0.979 1.76,1.156 0.156,0.177 10 false *2 4.99,0.688 5.146,0.865 0.156,0.177 10 false *5 5.875,1.156 6.031,1.333 0.156,0.177 10 false *6 5.625,2.396 5.781,2.573 0.156,0.177 10 false *7 5.375,2.667 5.531,2.844 0.156,0.177 10 false *8 4.656,3.25 4.885,3.427 0.229,0.177 10 false *10 5,2.969 5.156,3.146 0.156,0.177 10 false *9 4.125,3.5 4.354,3.677 0.229,0.177 10 false *11 3.354,3.792 3.583,3.969 0.229,0.177 10 false *12 1.708,3.823 1.938,4 0.229,0.177 10 false *13 0.948,3.448 1.177,3.625 0.229,0.177 10 false *14 0.75,2.146 0.979,2.323 0.229,0.177 10 false *15

Text in Illustration
*1 Center Differential Case *2 Ring Gear
*3 Pinion Gear *4 Front Drive Clutch Sleeve
*5 Planetary Carrier *6 Front Drive Sprocket
*7 Transfer Front Drive Spline Piece *8 No. 4 Clutch Plate
*9 Transfer Clutch Hub *10 No. 3 Clutch Plate
*11 No. 2 Clutch Plate *12 Coupling
*13 Sun Gear *14 Transfer Rear Output Shaft
*15 No. 1 Clutch Plate - -



d.

Transfer Shift Actuator Assembly

i.

The transfer shift actuator assembly consists of the high-low switching mechanism (to switch the transfer gear ratio) and the free-lock switching mechanism (to switch the center differential lock).

X102234E04
0.99,1.354 1.448,1.354 true 1.375,1.104 1.833,1.104 true 0.802,1.25 1,1.51 0.198,0.26 10 false *1 1.865,1.01 2.115,1.292 0.25,0.281 10 false *2 4.427,0.875 4.677,1.146 0.25,0.271 10 false *a 4.427,2.615 4.656,2.875 0.229,0.26 10 false *b

Text in Illustration
*1 Center Differential Lock Shift Fork Shaft *2 H-L Shift Fork Shaft
*a High-low Switching Mechanism (to Switch Transfer Gear Ratio) *b Free-lock Switching Mechanism (to Switch Center Differential Lock)

X102235E05
3.521,3.25 5.844,3.646 2.323,0.396 10 false High-low Switching Mechanism 3.438,4.115 5.729,4.49 2.292,0.375 10 false Center Differential Lock Shift Motor 3.458,5.542 5.885,5.885 2.427,0.344 10 false Center Differential Lock Limit Switch 3.333,6.031 5.948,6.385 2.615,0.354 10 false Center Differential Lock Position Switch 3.542,6.979 5.938,7.385 2.396,0.406 10 false Transfer Shift Actuator Assembly 3.948,2.823 5.24,3.188 1.292,0.365 10 false H-L Limit Switch 4.01,1.375 5.281,1.75 1.271,0.375 10 false H-L Shift Motor 3.542,6.469 5.969,6.865 2.427,0.396 10 false Free-lock Switching Mechanism 1.854,1.281 2.292,1.708 0.438,0.427 10 false HM1 1.854,1.792 2.229,2.135 0.375,0.344 10 false HM2 1.854,2.25 2.24,2.635 0.385,0.385 10 false HL1 1.854,2.708 2.219,3.229 0.365,0.521 10 false HL2 1.854,4.542 2.281,4.948 0.427,0.406 10 false TM2 1.865,5.01 2.229,5.375 0.365,0.365 10 false TL2 1.854,5.438 2.208,5.865 0.354,0.427 10 false TL3 1.854,6.031 2.115,6.427 0.26,0.396 10 false P1 1.865,4.021 2.26,4.417 0.396,0.396 10 false TM1 0.542,3.552 1.781,4.229 1.24,0.677 10 false 4WD Control ECU 0.083,0.052 1.552,0.5 1.469,0.448 10 false Wiring Diagram

·

High-low Switching Mechanism

-

By rotating the H-L shift motor clockwise or counterclockwise in accordance with a signal from the 4WD control ECU, the H-L shift fork shaft is transferred to switch the transfer gear ratio between high and low.

-

The drive mechanism for switching the transfer gear ratio between high and low consists of an H-L shift motor, H-L limit switch, and H-L shift fork shaft.

-

The H-L limit switch detects the H-L shift motor position.



X102236E06
0.99,0.865 1.708,0.865 1.708,0.865 2.323,1.823 true 6.021,0.813 5.448,0.813 5.448,0.813 4.958,1.188 true 1,2.75 1.781,2.75 1.781,2.75 2.458,2.406 true 0.802,0.781 0.958,0.958 0.156,0.177 10 false *1 0.844,2.667 1,2.844 0.156,0.177 10 false *3 6.063,0.729 6.219,0.906 0.156,0.177 10 false *2 5.042,1.49 5.323,1.719 0.281,0.229 10 false *a 5.719,1.5 6.01,1.729 0.292,0.229 10 false *b

Text in Illustration
*1 H-L Limit Switch *2 H-L Shift Fork Shaft
*3 H-L Shift Motor - -
*a Low Side *b High Side

X102237E06
0.083,0.073 2.323,0.25 2.24,0.177 10 false High-low Switching Detection Signal 2.771,0.75 3.073,0.927 0.302,0.177 10 false High 4.677,0.729 4.948,0.906 0.271,0.177 10 false Low 0.646,1.292 0.917,1.469 0.271,0.177 10 false HL1 0.646,2.146 0.917,2.323 0.271,0.177 10 false HL2 1.26,1.073 1.542,1.271 0.281,0.198 10 false Off 1.26,1.927 1.51,2.125 0.25,0.198 10 false Off 1.26,1.479 1.458,1.656 0.198,0.177 10 false On 1.26,2.354 1.458,2.531 0.198,0.177 10 false On

·

Free-lock Switching Mechanism

-

By rotating the center differential lock shift motor clockwise or counterclockwise in accordance with a signal from the 4WD control ECU, the center differential lock shift fork shaft is transferred to switch the center differential between free and lock.

-

The drive mechanism for switching the center differential between free and lock consists of a center differential lock shift motor, center differential lock limit switch, center differential lock position switch, and center differential lock shift fork shaft.

-

The center differential lock limit switch detects the center differential lock shift motor position.

-

The center differential lock position switch detects the lock position of the center differential.



X102238E06
1.01,0.833 1.729,0.833 1.729,0.833 2.625,1.375 true 6.073,0.854 5.5,0.854 5.5,0.854 5.01,1.229 true 4.375,2.365 3.802,2.365 3.802,2.365 2.979,1.833 true 1.021,2.729 1.802,2.729 1.802,2.729 2.521,2.469 true 0.854,0.75 1.01,0.927 0.156,0.177 10 false *1 0.854,2.646 1.01,2.823 0.156,0.177 10 false *3 6.125,0.781 6.281,0.958 0.156,0.177 10 false *2 4.771,1.5 4.927,1.677 0.156,0.177 10 false *a 5.438,1.5 5.594,1.677 0.156,0.177 10 false *b 4.427,2.281 4.583,2.458 0.156,0.177 10 false *4

Text in Illustration
*1 Center Differential Lock Limit Switch *2 Center Differential Lock Shift Fork Shaft
*3 Center Differential Lock Shift Motor *4 Center Differential Lock Position Switch
*a Lock Side *b Free Side

X102239E02
0.073,0.073 2.823,0.5 2.75,0.427 10 Free-lock Switching Detection Signal 2.271,0.771 2.625,1.125 0.354,0.354 10 Free 4.917,0.76 5.25,1.115 0.333,0.354 10 Lock 0.802,1.281 1.094,1.635 0.292,0.354 10 TL2 0.792,2.177 1.083,2.531 0.292,0.354 10 TL3 1.427,1.063 1.74,1.417 0.313,0.354 10 Off 1.417,1.948 1.729,2.302 0.313,0.354 10 Off 1.417,1.479 1.656,1.833 0.24,0.354 10 On 0.823,3.042 1.115,3.396 0.292,0.354 10 P1 1.417,2.823 1.729,3.177 0.313,0.354 10 Off 1.417,3.26 1.656,3.615 0.24,0.354 10 On 1.417,2.365 1.656,2.719 0.24,0.354 10 On



e.

Transfer Position Switch

i.

On the models with 1GR-FE, 1GD-FTV or 1KD-FTV engine, operating the transfer position switch can switch the transfer gear ratio between high and low.

X138121E01
2.396,1.573 2.396,1.198 true 4.938,1.563 4.938,1.125 true 2.24,1.583 3.156,1.781 0.917,0.198 10 false *1(*A) 4.802,1.563 5.969,1.781 1.167,0.219 10 false *1(*B)

Text in Illustration
*A Models without Multi-terrain Select *B Models with Multi-terrain Select
*1 Transfer Position Switch - -


ii.

On the models with 2TR-FE or 5L-E engine, operating the rotary type transfer position switch can switch the transfer gear ratio between high and low and the center differential between free and lock.

X102241E04
3.594,1.271 3.594,1.469 true 3.531,1.479 3.917,1.719 0.385,0.24 10 false *1

Text in Illustration
*1 Transfer Position Switch - -



f.

Center Differential Lock Switch (Models with 4 Drive Mode)

i.

On the models with 1GR-FE, 1GD-FTV or 1KD-FTV engine, operating the push type center differential lock switch can switch the center differential between free and lock.

X138143E01
2.292,1.833 2.927,2.875 true 5.385,1.917 5.927,2.781 true 2.833,2.875 3.75,3.073 0.917,0.198 10 false *1(*A) 5.865,2.813 6.781,3.01 0.917,0.198 10 false *1(*B)

Text in Illustration
*A Models with Multi-terrain Select *B Models without Multi-terrain Select
*1 Center Differential Lock Switch - -




OPERATION


a.

High-low Switching of Transfer Gear Ratio

i.

High Position

·

In the high position, the internal gear teeth of the transfer high and low clutch sleeve mesh with the transfer clutch hub spline piece.

·

Also, the transfer high and low clutch sleeve is connected to the center differential case.

·

The rotation of the transfer input shaft is transmitted to the planetary sun gear, transfer clutch hub spline piece, transfer high and low clutch sleeve, and the differential case.


X102242E03
1.208,1.073 1.958,1.073 1.958,1.073 2.656,1.854 true 1.958,0.656 2.385,0.656 2.385,0.656 2.729,1.604 true 3.573,0.656 3.198,0.656 3.198,0.656 3.031,1.625 true 4.427,1.042 4.094,1.042 4.094,1.042 3.823,1.781 true 1.615,3.042 1.333,3.042 1.333,3.042 1.208,2.625 true 3.615,3.052 3.375,3.052 3.375,3.052 3.229,2.229 true 4.208,3.063 3.917,3.063 3.917,3.063 3.552,2.031 true 5.042,2.979 5.042,2.583 5.042,2.583 5.479,2.031 true 0.833,1.552 1.635,1.552 1.635,1.552 2.656,2.188 true 5.667,2.948 5.667,2.438 true 6.313,2.927 6.313,1.99 true 0.667,1.438 0.844,1.677 0.177,0.24 10 false *1 1.031,0.958 1.25,1.219 0.219,0.26 10 false *2 1.781,0.542 1.969,0.792 0.188,0.25 10 false *3 3.615,0.552 3.813,0.802 0.198,0.25 10 false *4 4.458,0.938 4.677,1.219 0.219,0.281 10 false *5 1.635,2.927 1.833,3.188 0.198,0.26 10 false *6 3.635,2.938 3.854,3.229 0.219,0.292 10 false *7 4.229,2.958 4.479,3.24 0.25,0.281 10 false *8 4.99,2.969 5.24,3.24 0.25,0.271 10 false *1 5.615,2.938 5.854,3.24 0.24,0.302 10 false *2 6.271,2.917 6.49,3.24 0.219,0.323 10 false *3

Text in Illustration
*1 Planetary Sun Gear *2 Planetary Pinion Gear
*3 Planetary Ring Gear *4 Planetary Carrier
*5 Transfer High and Low Clutch Sleeve *6 Transfer Input Shaft
*7 Transfer Clutch Hub Spline Piece *8 Center Differential Case


ii.

Low Position

·

In the low position, the external teeth of the transfer high and low clutch sleeve mesh with the transfer low planetary spline piece.

·

Also, the transfer high and low clutch sleeve is connected to the center differential case.

·

The rotation of the transfer input shaft is transmitted in a reduced form to the planetary sun gear, planetary pinion gears, planetary pinion gear shafts, planetary carrier, transfer low planetary spline piece, transfer high and low clutch sleeve, and center differential case.


X102243E07
1.208,1.052 1.958,1.052 1.958,1.052 2.656,1.833 true 1.958,0.656 2.385,0.656 2.385,0.656 2.729,1.604 true 3.573,0.646 3.198,0.646 3.198,0.646 3.031,1.615 true 4.688,1.031 4.344,1.031 4.344,1.031 4.083,1.771 true 1.625,3.021 1.344,3.021 1.344,3.021 1.219,2.604 true 3.99,0.906 3.667,0.906 3.667,0.906 3.469,1.552 true 4.198,3.063 3.906,3.063 3.906,3.063 3.542,2.031 true 5.042,2.938 5.042,2.542 5.042,2.542 5.479,1.99 true 0.833,1.552 1.635,1.552 1.635,1.552 2.656,2.188 true 5.656,2.969 5.656,2.458 true 6.323,2.927 6.323,1.99 true 0.656,1.479 0.844,1.729 0.188,0.25 10 false *1 1.031,0.969 1.219,1.219 0.188,0.25 10 false *2 1.781,0.563 1.969,0.813 0.188,0.25 10 false *3 3.635,0.563 3.865,0.813 0.229,0.25 10 false *4 4.719,0.927 4.927,1.198 0.208,0.271 10 false *6 1.677,2.927 1.896,3.198 0.219,0.271 10 false *7 4.031,0.813 4.25,1.083 0.219,0.271 10 false *5 4.26,2.979 4.521,3.292 0.26,0.313 10 false *8 4.99,2.958 5.24,3.24 0.25,0.281 10 false *1 5.615,2.979 5.844,3.26 0.229,0.281 10 false *2 6.271,2.938 6.469,3.229 0.198,0.292 10 false *3

Text in Illustration
*1 Planetary Sun Gear *2 Planetary Pinion Gear
*3 Planetary Ring Gear *4 Planetary Carrier
*5 Transfer Low Planetary Spline Piece *6 Transfer High and Low Clutch Sleeve
*7 Transfer Input Shaft *8 Center Differential Case



b.

Free-lock Switching of Center Differential

i.

Lock Position

In the lock position, the front drive clutch sleeve connects the center differential case and the transfer front drive spline piece to set the center differential to lock.


X102244E08
5.354,2.354 5.833,2.354 true 5.365,2.719 5.844,2.719 true 1.854,0.667 2.49,1.531 true 4.073,0.667 4.354,1.25 true 5.135,0.802 4.729,1.99 true 6.125,1.521 5.667,1.729 true 5.625,3.094 5.219,2.771 true 2.698,1.021 2.563,1.354 true 1.75,0.469 1.969,0.667 0.219,0.198 10 false *1 3.958,0.458 4.219,0.677 0.26,0.219 10 false *5 5.104,0.615 5.313,0.844 0.208,0.229 10 false *4 6.156,1.396 6.375,1.698 0.219,0.302 10 false *3 5.656,3 5.969,3.292 0.313,0.292 10 false *2 2.635,0.813 2.906,1.031 0.271,0.219 10 false *a 5.865,2.24 6.083,2.49 0.219,0.25 10 false *c 5.865,2.615 6.115,2.854 0.25,0.24 10 false *b

Text in Illustration
*1 Center Differential Case *2 Front Drive Clutch Sleeve
*3 Transfer Front Drive Spline Piece *4 Front Drive Sprocket
*5 Transfer Rear Output Shaft - -
*a Input Torque *b Front Output Torque
*c Rear Output Torque - -



c.

Operation of Center Differential

i.

Normal Driving Operation

During normal driving (front wheel speed = rear wheel speed), the drive torque that is input by the differential case is transmitted (front: 40/rear: 60) as shown below, without involving the LSD function.


X102245E07
1.271,0.688 1.573,0.688 1.573,0.688 2.49,1.542 true 2.646,0.667 2.927,0.667 2.927,0.667 3.208,1.802 true 4.031,0.635 3.813,0.635 3.813,0.635 3.552,1.677 true 5.094,0.594 4.802,0.594 4.802,0.594 4.167,1.729 true 6.24,0.656 5.969,0.656 5.969,0.656 5.656,1.708 true 2.896,3.104 3.135,3.104 3.135,3.104 3.323,2.344 true 6.188,3.094 5.938,3.094 5.938,3.094 5.688,2.781 true 2.583,1.156 2.583,1.344 true 5.344,2.375 5.542,2.375 true 5.354,2.729 5.552,2.729 true 1.094,0.594 1.25,0.771 0.156,0.177 10 false *1 2.448,0.583 2.604,0.76 0.156,0.177 10 false *2 4.083,0.542 4.24,0.719 0.156,0.177 10 false *3 5.177,0.51 5.333,0.688 0.156,0.177 10 false *4 6.313,0.563 6.469,0.74 0.156,0.177 10 false *5 6.271,3.01 6.469,3.219 0.198,0.208 10 false *7 2.708,3.01 2.865,3.188 0.156,0.177 10 false *6 2.49,0.948 2.646,1.125 0.156,0.177 10 false *a 5.594,2.271 5.75,2.448 0.156,0.177 10 false *b 5.573,2.625 5.729,2.802 0.156,0.177 10 false *c

Text in Illustration
*1 Center Differential Case *2 Pinion Gear
*3 Ring Gear *4 Planetary Carrier
*5 Front Drive Sprocket *6 Sun Gear
*7 Transfer Rear Output Shaft - -
*a Input Torque *b Front Output Torque
*c Rear Output Torque - -


ii.

Front Wheel Skid Driving Operation

During front wheel skid driving (front wheel speed > rear wheel speed) when a rotational difference exists between the sun gear and the ring gear, the distribution of the drive torque that is input by the center differential case changes instantly before the torque is transmitted, as follows:

-

The sun gear transmits torque to the planetary carrier while pushing on the No. 4 clutch plate. The planetary carrier transmits this torque to the ring gear from the center differential case via the No. 1 clutch plate.

-

The ring gear outputs torque while pushing on the No. 1 clutch plate.

-

These LSD functions change the torque distribution.



X102246E08
1.25,0.646 1.552,0.646 1.552,0.646 2.469,1.51 true 2.646,0.667 2.927,0.667 2.927,0.667 3.208,1.802 true 4.031,0.625 3.813,0.625 3.813,0.625 3.552,1.677 true 5.094,0.625 4.802,0.625 4.802,0.625 4.167,1.75 true 6.219,0.667 5.948,0.667 5.948,0.667 5.635,1.719 true 1.854,3.146 2.094,3.146 2.094,3.146 2.583,2.24 true 1.25,3.083 1.49,3.083 1.49,3.083 2.531,2.052 true 2.885,3.083 3.125,3.083 3.125,3.083 3.313,2.323 true 2.396,3.104 2.646,3.104 2.646,3.104 2.646,2.458 true 6.188,3.104 5.938,3.104 5.938,3.104 5.688,2.781 true 3.563,3.104 3.802,3.104 3.802,3.104 3.896,2.354 true 4.323,3.094 4.104,3.094 4.104,3.094 3.99,2.302 true 4.917,3.146 4.698,3.146 4.698,3.146 4.573,2.354 true 2.573,1.146 2.573,1.344 true 5.354,2.365 5.542,2.365 true 5.365,2.729 5.563,2.729 true 1.052,0.552 1.208,0.729 0.156,0.177 10 false *1 2.49,0.583 2.646,0.76 0.156,0.177 10 false *2 4.063,0.542 4.219,0.719 0.156,0.177 10 false *3 5.135,0.531 5.292,0.708 0.156,0.177 10 false *4 6.24,0.583 6.396,0.76 0.156,0.177 10 false *5 6.219,3 6.448,3.177 0.229,0.177 10 false *11 3.406,3.021 3.563,3.198 0.156,0.177 10 false *9 2.729,2.99 2.885,3.167 0.156,0.177 10 false *8 1.688,3.042 1.844,3.219 0.156,0.177 10 false *6 4.365,2.99 4.521,3.167 0.156,0.177 10 false *e 1.063,2.99 1.396,3.25 0.333,0.26 10 false *d 2.24,3.01 2.396,3.188 0.156,0.177 10 false *7 4.938,3.031 5.167,3.208 0.229,0.177 10 false *10 2.49,0.948 2.646,1.125 0.156,0.177 10 false *a 5.573,2.281 5.729,2.458 0.156,0.177 10 false *b 5.583,2.604 5.74,2.781 0.156,0.177 10 false *c

Text in Illustration
*1 Center Differential Case *2 Pinion Gear
*3 Ring Gear *4 Planetary Carrier
*5 Front Drive Sprocket *6 No. 1 Clutch Plate
*7 Coupling *8 Sun Gear
*9 No. 4 Clutch Plate *10 Transfer Clutch Hub
*11 Transfer Rear Output Shaft - -
*a Input Torque *b Front Output Torque
*c Rear Output Torque *d Pushing on No. 1 Clutch Plate
*e Pushing on No. 4 Clutch Plate - -


iii.

Rear Wheel Skid Driving Operation

During rear wheel skid driving (front wheel speed < rear wheel speed), when a rotational difference exists between the sun gear and the ring gear, the distribution of the drive torque that is input by the center differential case changes instantly before the torque is transmitted, as follows:

-

The ring gear transmits torque to the center differential case while pushing on the No. 1 clutch plate. The center differential case transmits this torque from the planetary carrier to the sun gear via the No. 4 clutch plate.

-

The sun gear outputs torque while pushing on the No. 4 clutch plate.

-

These LSD functions change the torque distribution.






X102247E08
1.271,0.677 1.573,0.677 1.573,0.677 2.49,1.542 true 2.646,0.677 2.927,0.677 2.927,0.677 3.208,1.813 true 4.031,0.635 3.813,0.635 3.813,0.635 3.552,1.688 true 5.083,0.635 4.792,0.635 4.792,0.635 4.156,1.76 true 6.24,0.688 5.969,0.688 5.969,0.688 5.656,1.74 true 4.333,3.094 4.115,3.094 4.115,3.094 3.99,2.271 true 1.854,3.083 2.094,3.083 2.094,3.083 2.583,2.177 true 1.24,3.094 1.479,3.094 1.479,3.094 2.521,2.063 true 2.917,3.083 3.156,3.083 3.156,3.083 3.344,2.323 true 2.396,3.083 2.646,3.083 2.646,3.083 2.646,2.438 true 6.229,3.115 5.979,3.115 5.979,3.115 5.729,2.802 true 3.573,3.073 3.813,3.073 3.813,3.073 3.906,2.323 true 4.927,3.104 4.708,3.104 4.708,3.104 4.583,2.313 true 2.573,1.146 2.573,1.344 true 5.375,2.354 5.573,2.354 true 5.375,2.719 5.573,2.719 true 1.104,0.552 1.281,0.792 0.177,0.24 10 false *1 2.458,0.552 2.646,0.781 0.188,0.229 10 false *2 4.063,0.531 4.26,0.802 0.198,0.271 10 false *3 5.115,0.521 5.344,0.771 0.229,0.25 10 false *4 6.271,0.583 6.469,0.854 0.198,0.271 10 false *5 4.354,2.99 4.583,3.229 0.229,0.24 10 false *e 6.26,3.01 6.563,3.229 0.302,0.219 10 false *11 3.406,2.969 3.594,3.208 0.188,0.24 10 false *9 2.74,2.979 2.938,3.229 0.198,0.25 10 false *8 1.677,2.969 1.875,3.208 0.198,0.24 10 false *6 1.063,2.979 1.25,3.24 0.188,0.26 10 false *d 2.24,2.969 2.427,3.219 0.188,0.25 10 false *7 4.948,3.01 5.25,3.24 0.302,0.229 10 false *10 2.479,0.948 2.698,1.156 0.219,0.208 10 false *a 5.594,2.24 5.833,2.448 0.24,0.208 10 false *b 5.583,2.604 5.844,2.802 0.26,0.198 10 false *c

Text in Illustration
*1 Center Differential Case *2 Pinion Gear
*3 Ring Gear *4 Planetary Carrier
*5 Front Drive Sprocket *6 No. 1 Clutch Plate
*7 Coupling *8 Sun Gear
*9 No. 4 Clutch Plate *10 Transfer Clutch Hub
*11 Transfer Rear Output Shaft - -
*a Input Torque *b Front Output Torque
*c Rear Output Torque *d Pushing on No. 1 Clutch Plate
*e Pushing on No. 4 Clutch Plate - -