Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2017.08
NM27T0E _59 Vehicle Exterior _053648 WIPER / WASHER _0260201 WIPER AND WASHER SYSTEM UN GENERAL/CONTROL/DETAILS F

WIPER / WASHER  WIPER AND WASHER SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


OPERATING CONDITION


a.

Headlight Cleaner System

i.

The headlight cleaner system operates as follows:

Headlight Low Beam Headlight Cleaner Switch Washer Switch (Windshield Wiper Switch Assembly)
On On
(First Time)
On
(Second Time or later)
Turn On Activated Activated Not Activated
Turn Off Not Activated Not Activated Not Activated




SYSTEM CONTROL


a.

The wiper and washer system has the following functions:

Function Outline
Wiper*1 Vehicle Speed-sensing, Adjustable Interval This function controls the wiper interval time in accordance with the vehicle speed when the windshield wiper switch assembly is in the AUTO or INT position.
Raindrop Sensing Controls the wiping interval and speed in accordance with the amount of rain, the vehicle speed and the luminance of the surrounding area when the windshield wiper switch assembly is in the AUTO position.
Washer-linked Wiper with Drip-prevention To prevent the fluid from dripping after the washer has been operated, this function operates the wipers once after they have operated in unison with the washer.
Washer Headlight Cleaner*2 Sprays washer fluid on the headlight lenses to clean them.
Washer Fluid Level Warning When the volume of washer fluid decreases to below a certain level, the combination meter assembly warns the driver through the warning message on the multi-information display.
Washer Nozzle Heater*3 The heater in washer nozzle sub-assembly is activated to prevent water inside the nozzle from freezing and blocking the washer fluid.

*1: Models with raindrop sensing function

*2: Models with headlight cleaner system

*3: Models with washer nozzle heater



b.

Washer Fluid Level Warning

i.

When the volume of washer fluid decreases to below a certain level, the combination meter assembly displays the messages on the multi-information display*1 or illuminates the washer fluid level indicator light*2 to warning the driver.

*1: Models with Optitron display type combination meter assembly

*2: Models with analog display type combination meter assembly




c.

Rain Sensing Function

i.

The rain sensing function controls the wiping timing in accordance with the amount of rain detected when the AUTO switch (windshield wiper switch assembly) is on.


ii.

This control is performed by the windshield wiper relay assembly to switch the wiper operation as shown in the following chart (Wiper Operation Chart) based on the amount of rain and vehicle speed.


iii.

A luminance detection function is provided to automatically change the rain sensitivity according to day or night.

Wiper Operation Chart
Amount of rain While driving vehicle While vehicle is stopped
Large Continuous HI operation Continuous LO operation
↓↑ Continuous LO operation Continuous LO operation
↓↑ Stops intermittently approximatelyevery 0.6 seconds Stops intermittently approximatelyevery 0.8 seconds
↓↑ Stops intermittently approximatelyevery 1.2 seconds Stops intermittently approximatelyevery 1.6 seconds
↓↑ Stops intermittently approximatelyevery 2.1 seconds Stops intermittently approximatelyevery 3.1 seconds
↓↑ Stops intermittently approximatelyevery 3.5 seconds Stops intermittently approximatelyevery 5.4 seconds
↓↑ Stops intermittently approximatelyevery 5.9 seconds Stops intermittently approximatelyevery 9.7 seconds
↓↑ Stops intermittently approximatelyevery 10.1 seconds Stops intermittently approximatelyevery 17.5 seconds
Small Stops intermittently approximatelyevery 17.9 seconds Stops intermittently approximatelyevery 32.7 seconds
Not detected Stopped Stopped



d.

Rain Sensor Sensitivity Level Adjustment Function

i.

When the auto sensitivity adjustment switch is operated with the AUTO switch of the front wiper switch (windshield wiper switch assembly) set to ON, rain sensor sensitivity level adjustment can be performed and the wiper operation timing changes.



e.

Vehicle Speed-Sensing, Adjustable Interval function

i.

When the wiper control switch is in the INT (AUTO) position, the interval time of the wiper is controlled in 3 stages in accordance with the automatic control adjuster position and the vehicle speed.


ii.

The interval time can be controlled steplessly within each range.

Y231666E02
4.208,1.677 4.208,1.073 4.208,1.073 4.792,1.073 true 4.292,3.323 4.292,3.438 4.292,3.438 5.365,3.438 true 1.104,0.292 1.719,0.49 0.615,0.198 10 false Sec. 1.198,0.646 1.813,0.844 0.615,0.198 10 false 15 1.198,1.594 1.813,1.792 0.615,0.198 10 false 10 1.271,2.542 1.458,2.74 0.188,0.198 10 false 5 1.74,3.667 1.927,3.865 0.188,0.198 10 false 0 0.177,1.865 1.031,2.219 0.854,0.354 10 false Interval Time 2.406,3.635 2.875,3.833 0.469,0.198 10 false 20 (12) 3.188,3.646 3.656,3.844 0.469,0.198 10 false 40 (25) 4,3.656 4.469,3.854 0.469,0.198 10 false 60 (37) 2.219,2.25 4.177,2.552 1.958,0.302 10 false Interval Time Adjustment Range 4.646,3.594 5.385,3.854 0.74,0.26 10 false km/h (mph) 4.99,0.99 6.906,1.344 1.917,0.354 10 false Automatic Control Adjuster Position: SLOW 5.427,3.333 7.083,3.698 1.656,0.365 10 false Automatic Control Adjuster Position: FAST 2.75,4.021 3.74,4.417 0.99,0.396 10 false Vehicle Speed



f.

Washer-linked with Drip-prevention Function

i.

When the front wiper switch is set to OFF and the front windshield washer switch is turned on, the washer fluid is sprayed and after approximately 0.5 seconds the front wipers start operating in LO.


ii.

The wipers operate 3 times in LO after the front windshield washer switch is turned off.


iii.

When the front wiper is not in operation with the vehicle stopped (the vehicle speed is less than approximately 4 km/h) after the washer-linked operation has completed, this function operates the front wiper once again approximately 3 seconds after the washer-linked operation to wipe away washer fluid.

Y202261E01
0.219,0.74 2.531,1.094 2.313,0.354 10 false Front Windshield Washer Switch 0.219,1.385 2.531,1.74 2.313,0.354 10 false Windshield Washer Motor and Pump Assembly 0.229,2.75 2.542,3.104 2.313,0.354 10 false Windshield Wiper Motor Assembly 4.313,0.396 5.365,0.719 1.052,0.323 10 false Approx. 0.5 sec. 2.854,0.51 3.24,0.74 0.385,0.229 10 false On 2.875,0.885 3.26,1.115 0.385,0.229 10 false Off 2.875,1.271 3.26,1.5 0.385,0.229 10 false On 2.885,1.708 3.271,1.938 0.385,0.229 10 false Off 2.927,2.938 3.313,3.167 0.385,0.229 10 false Off 2.906,2.49 3.292,2.719 0.385,0.229 10 false On 3.094,3.719 5.219,4.083 2.125,0.365 10 false Washer-linked Function Operates 4.542,3.344 5.594,3.667 1.052,0.323 10 false Approx. 3 sec. 5.323,2.448 6.51,2.865 1.188,0.417 10 false Drip-prevention Function Operates 4.552,2.052 5.74,2.385 1.188,0.333 10 false Operates 3 Times




CONSTRUCTION


a.

Rain Sensor

i.

The rain sensor consists of a Light Emitting Diode (LED) that emits infrared rays, a photo diode that can receive those rays, a lens and rain sensor tape.

Y215819E01
2.25,0.583 2.583,0.583 2.583,0.583 2.938,1.073 true 1.833,1.333 2.75,1.333 true 2.083,2.167 2.417,2.167 2.417,2.167 2.583,1.75 true 4.833,2.167 4.583,2.167 4.583,2.167 4.333,1.75 true 3.302,2.167 3.052,2.167 3.052,2.167 2.969,1.75 true 1.115,0.5 2.281,0.823 1.167,0.323 10 false Rain Sensor Tape 1.49,1.24 1.906,1.563 0.417,0.323 10 false Lens 1.25,2.094 2.083,2.417 0.833,0.323 10 false Photo Diode 4.885,2.094 5.719,2.417 0.833,0.323 10 false LED 3.333,2.083 4.167,2.406 0.833,0.323 10 false Photo Diode

HINT:

If the rain sensor tape has been peeled off during a windshield glass replacement, make sure to affix new rain sensor tape. Failure to do so will lead to a system malfunction.



ii.

If no raindrops are present in the detection area, the infrared rays emitted by the LED are all reflected from the outer surface of the windshield glass and are received by the photo diode.


iii.

If raindrops are present in the detection area, a portion of the emitted infrared rays penetrates the windshield glass due to the change in the difference of the index of refraction between the glass and the area outside the windshield (difference between air and water). The ability of the windshield glass to reflect all light back inside changes due to the presence of raindrops. This change of internal reflection due to the presence of water reduces the amount of infrared rays that are received by the photo diode. The amount of this reduction is then used to determine the amount of raindrops. Thus, this function selects the INT, LO, and HI wiper operations in order to operate the wipers at an optimal speed and timing.

Y215820E01
2.583,1.083 2.75,0.583 2.75,0.583 2.917,0.583 true 1.583,1.229 1.417,0.646 1.417,0.646 1.25,0.646 true 1,1.833 1.083,2.417 1.083,2.417 0.917,2.417 true 1.333,1.833 1.417,2.25 1.417,2.25 1.583,2.25 true 2.5,1.833 2.583,2.417 2.583,2.417 2.833,2.417 true 4.417,1.833 4.333,2.417 4.333,2.417 4.167,2.417 true 4.75,1.833 4.833,2.167 4.833,2.167 5,2.167 true 5.917,1.833 6.167,2.417 6.167,2.417 6.417,2.417 true 4.99,0.833 4.74,0.25 4.74,0.25 4.573,0.25 true 5.25,1 5.417,0.5 5.417,0.5 5.583,0.5 true 2.979,0.5 4.083,0.781 1.104,0.281 10 false Windshield Glass 0.469,0.563 1.219,0.896 0.75,0.333 10 false Infrared Ray 0.083,2.333 0.917,2.667 0.833,0.333 10 false Photo Diode 1.604,2.177 2.438,2.51 0.833,0.333 10 false Photo Diode 2.885,2.333 3.719,2.667 0.833,0.333 10 false LED 3.396,2.333 4.229,2.667 0.833,0.333 10 false Photo Diode 5.083,2.083 5.917,2.417 0.833,0.333 10 false Photo Diode 6.458,2.333 7.031,2.667 0.573,0.333 10 false LED 3.813,0.167 4.563,0.5 0.75,0.333 10 false Infrared Ray 5.667,0.417 6.417,0.75 0.75,0.333 10 false Raindrop



b.

Washer Nozzle

i.

Spray type washer nozzles are located under the engine hood to ensure good appearance. These nozzles can spray windshield washer fluid over a wide area by spraying it in a fan shape. The washer fluid volume has been reduced so as not to hinder the driver's view when the washer system is operated.

Y221789E01
0.563,1.219 0.75,0.75 0.75,0.75 0.917,0.75 true 1.333,1.333 1.417,1.75 1.417,1.75 1.583,1.75 true 0.979,0.667 2.667,0.865 1.688,0.198 10 false Engine Hood 1.625,1.667 3.313,1.865 1.688,0.198 10 false Washer Nozzle 6.167,0.385 7,0.583 0.833,0.198 10 false Fluid Volume 5.906,1.135 7.063,1.385 1.156,0.25 10 false Main Flow Center

HINT:

Spray type washer nozzles cannot be adjusted because of their structure. Do not attempt to adjust the nozzles as it could damage them. If adjustment is necessary, adjust the nozzles by replacing them with nozzles that have different spray angles. For details, refer to the Repair Manual.



ii.

Washer Nozzle Heater (Models with Washer Nozzle Heater)

·

When the outside temperature meets or falls below a fixed level, the PTC heater is activated based on signals from the washer nozzle heater relay to prevent water inside the nozzle from freezing and blocking the washer fluid.

Y215717C01
6.156,1.469 6.552,2.521 true 0.354,2.104 0.521,2.323 0.167,0.219 12 false A 3.083,2.115 3.25,2.333 0.167,0.219 12 false A 1.594,3.448 1.833,3.656 0.24,0.208 10 false *1 5.604,3.417 5.844,3.625 0.24,0.208 10 false *a 6.052,1.292 6.292,1.5 0.24,0.208 10 false *2
*1 Washer Nozzle Sub-assembly *2 PTC Heater
*a A - A Cross Section - -






FAIL-SAFE


a.

The following fail-safe measures are taken if a malfunction is detected by the windshield wiper switch assembly.

Trouble Area Condition
Wiper Motor Malfunction Stops the operation of the raindrop sensing function.
Communication Signal Malfunction Rain Sensor Stops the operation of the raindrop sensing function.
When a signal cannot be received from the rain sensor, the raindrop sensing function is not performed and the status that existed prior to the occurrence of abnormality is maintained.
Combination Meter Assembly
·

Stops the operation of the vehicle speed-sensing, adjustable interval vehicle function.

·

Stops the operation of the speed switching function.

·

Stops the operation of the stopped vehicle intermittent wiper function.

·

The wiper interval can be adjusted.