Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Hydraulic Brake Booster) › 2017.08–2020.08
NM27T0E _54 Brake _053625 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260161 BRAKE CONTROL SYSTEM(for Hydraulic Brake Booster) UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Hydraulic Brake Booster)  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with downhill assist control

*2: Models with multi-terrain select

*3: Models with Optitron display type combination meter assembly

*4: Models without multi-terrain select

*5: Models with rear differential lock system

*6: Models with pre-crash safety system

Combination Meter Assembly Brake System Warning Light
·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD.

·

Illuminates to alert the driver when the brake fluid level is low.

·

Illuminates to alert the driver that the hydraulic pressure of the brake booster accumulator assembly in the hydraulic brake booster assembly has decreased.


Parking Brake Indicator Light Illuminates to inform the driver of the parking brake condition.
ABS Warning Light Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS or multi-terrain ABS.
Slip Indicator Light Blinks to inform the driver when the TRC, A-TRC, VSC, trailer sway control, hill-start assist control, downhill assist control*1 and CRAWL*2 are operational.
TRC OFF Indicator Light Illuminates to inform the driver that the TRC OFF mode has been entered using the VSC OFF switch.
VSC OFF Indicator Light Illuminates to inform the driver that the VSC OFF mode has been entered using the VSC OFF switch.
Downhill Assist Control Indicator Light*1 Illuminates to inform the driver that the downhill assist control switch has been turned on.
Multi-information Display*3
·

Multi-terrain Select Indicator*2: Illuminates to inform the driver that multi-terrain select control is available.

·

CRAWL Indicator*2: Illuminates to inform the driver that the CRAWL on/off switch has been turned on.

·

Displays multi-terrain select operation assist messages.*2

·

Displays multi-terrain select road mode.*2

·

Informs the driver of the status of the CRAWL operation.*2

·

Displays the warning message when the skid control ECU detects a malfunction in the system.


Master Warning Light*3 Illuminates or blinks when the warning message is displayed in the multi-information display.
Multi Buzzer
·

Sounds when the warning message is displayed in the multi-information display.*3

·

Sounds to inform the driver that a malfunction has occurred in the hydraulic brake booster assembly.


Speed Sensor Detects the wheel speed of each of the 4 wheels.
Steering Angle Sensor Detects the direction and angle of the steering wheel.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects that the parking brake lever is pulled up.
Module Switch*2 VSC OFF Switch Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode".
Multi-terrain Select Switch Turns the multi-terrain select on and off.
CRAWL On/Off Switch Turns the CRAWL on and off.
Multi-terrain Select Road Mode Selector Selects multi-terrain select road mode.
CRAWL Speed Selector Used to select the target vehicle speed when the CRAWL is active.
Downhill Assist Control Switch*1 Turns downhill assist control on and off.
VSC OFF Switch*4 Enables the driver to select "Normal Mode", "TRC OFF Mode" or "VSC OFF Mode".
Transfer Shift Actuator Assembly Center Differential Lock Detection Switch Detects the center differential lock condition.
Rear Differential Lock Detection Switch*5 Detects the rear differential lock condition.
Hydraulic Brake Booster Assembly Actuator Portion Changes the brake fluid path based on the signals from the skid control ECU during the operations of the brake control functions in order to control the fluid pressure that is applied to the wheel cylinders.
Brake Fluid Level Warning Switch Detects that the brake fluid level is low.
Master Cylinder Pressure Sensor Detects the master cylinder pressure and outputs this information to the skid control ECU.
Accumulator Pressure Sensor Monitors the hydraulic pressure of the brake booster accumulator assembly and outputs this information to brake booster pump assembly control.
Control Pressure Sensor*6 In brake control of the pre-crash safety system, hydraulic pressure is applied from the brake booster accumulator assembly to each wheel cylinder, generating braking force automatically. The control pressure sensor detects the control hydraulic pressure at that time.
Switching Solenoid Valve Switches the brake hydraulic path when the brake control system is activated.
Control Solenoid Valve Controls the hydraulic pressure that is applied to the wheel cylinders during brake control.
Brake Booster Pump Assembly Draws up the brake fluid from the brake master cylinder reservoir and provides high hydraulic pressure to the brake booster accumulator assembly.
Skid Control ECU Judges the vehicle driving condition based on signals from each sensor, and sends brake control signals to the hydraulic brake booster assembly.
4WD Control ECU Sends the transfer drive mode.
ECM
·

Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU.

·

Makes a request for brake control to the skid control ECU assembly.

·

Controls the engine output based on the signals received from the skid control ECU.


Driving Support ECU*6 Makes a request for brake control to the skid control ECU.
Center Airbag Sensor Assembly Yaw Rate Sensor Detects the vehicle's yaw rate.
Deceleration Sensor Detects the vehicle's longitudinal and lateral acceleration.


OPERATING CONDITION


a.

The brake control function varies by the transfer drive mode as shown in the following table:

Models without Multi-terrain Select
Brake Control Function Transfer Drive Mode
H4F H4L L4F L4L Rear Differential Lock On
ABS/Multi-terrain ABS ○ ○ ○ ○ X
EBD ○ ○ ○ ○ ○
Brake Assist ○ ○ ○ ○ X
TRC ○ ○ X X X
A-TRC X X ○ ○ ○
VSC ○ ○ ○ X X
Trailer Sway Control ○ ○ ○ X X
Hill-start Assist Control ○ ○ ○ ○ X
Downhill Assist Control X X ○ ○ X

HINT:

○: Operates

X: Does not operate


Models with Multi-terrain Select
Brake Control Function Transfer Drive Mode
H4F H4L L4F L4L Rear Differential Lock On
ABS/Multi-terrain ABS ○ ○ ○ ○ X
EBD ○ ○ ○ ○ ○
Brake Assist ○ ○ ○ ○ X
TRC ○ ○ X X X
A-TRC X X ○* ○* ○*
VSC ○ ○ ○ X X
Trailer Sway Control ○ ○ ○ X X
Hill-start Assist Control ○ ○ ○ ○ X
CRAWL X X ○ ○ ○

HINT:

○: Operates

X: Does not operate

*: When the multi-terrain select is on



b.

Hill-start Assist Control

i.

Hill-start assist control operates when all of the following conditions have been met:

Hill-start Assist Control Operation Condition - The shift lever is in D or S.
- The brake pedal is not depressed.
- The rear differential lock switch is off.
- The skid control ECU has detected the backward movement of the vehicle when the driver is starting off on a hill.


ii.

Hill-start assist control stops operating when any of the following conditions have been met:

Hill-start Assist Control Ending Condition - The shift lever is in any position other than D or S.
- The brake pedal is depressed.
- The rear differential lock switch is on.
- Approximately 5 seconds have passed since control commenced.



c.

Downhill Assist Control

i.

The downhill assist control operates when all of the following conditions have been met:

Downhill Assist Control Operation Condition - The downhill assist control switch is on.
- The transfer drive mode is in L4F or L4L.
- The accelerator pedal and brake pedal are not depressed.
- The rear differential lock switch is off.
- The vehicle is descending a hill at a sufficiently slow vehicle speed.


ii.

The downhill assist control stops operating when any of the following conditions have been met:

Downhill Assist Control Ending Condition - The downhill assist control switch is off.
- The transfer drive mode is in any position other than L4F or L4L.
- The accelerator pedal or brake pedal is depressed.
- The rear differential lock switch is on.



d.

CRAWL

i.

When the CRAWL on/off switch is on with all of the following conditions met, the CRAWL control starts operating:

CRAWL Operation Condition - The transfer drive mode is in L4F or L4L.
- The shift lever is in R, D or S.
- The 2nd start switch is off.
- The driver door is closed.

HINT:

If the accelerator pedal is depressed during CRAWL control, AUTO mode for the multi-terrain select turns on automatically. Also, the multi-terrain select on/off switch cannot be operated during CRAWL control.



ii.

CRAWL control stops operating when any of the following conditions have been met:

CRAWL Operation Ending Condition - The CRAWL on/off switch is off.
- The transfer drive mode is in any position other than L4F or L4L.
- The shift lever is in P or N.
- The driver door is opened.
- The vehicle speed is above 25 km/h (16 mph).



e.

Multi-terrain Select (When CRAWL Control is Off)

i.

When all of the following conditions are met, the multi-terrain select can be turned on or off and road mode can be selected by operating the multi-terrain select switch and multi-terrain select road mode selector, and the multi-terrain select indicator will illuminate.


ii.

When switching to the selected road mode, the mode is displayed on the multi-information display and engine output control and A-TRC control start.

Multi-terrain Select Operation Condition - The transfer drive mode is in L4F or L4L.
- The VSC OFF switch is off.


iii.

Multi-terrain select control will terminate if a malfunction occurs in the multi-terrain select switch operation, the brake control system, the engine control system or the 4WD control system.


iv.

The 2nd start switch and VSC OFF switch cannot be operated while multi-terrain select is in operation.




SYSTEM CONTROL


Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when brakes are applied firmly or when braking on a slippery surface.
Multi-terrain Anti-lock Brake System (Multi-terrain ABS) In addition to the existing ABS function, the multi-terrain ABS automatically calculates the optimum ABS control in accordance with off-road conditions such as dirt or sandy roads.
Electronic Brake Force Distribution (EBD) EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist
·

The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance.

·

If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


Traction Control (TRC) TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface.
Active Traction Control (A-TRC) A-TRC controls the brake hydraulic pressure that is applied to the slipping wheel, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an LSD effect.
Vehicle Stability Control (VSC) VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering.
Trailer Sway Control If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the engine output in order to suppress trailer sway.
Hill-start Assist Control When the vehicle starts off on a steep or a slippery hill, hill-start assist control detects the backward descent of the vehicle and performs 4-wheel hydraulic pressure control to reduce the backward speed of the vehicle. As a result, the vehicle can be started off on a hill more easily.
Downhill Assist Control When the downhill assist control switch is pressed while the transfer drive mode is in L4F or L4L, and without accelerator or brake pedal operation, downhill assist control activates to performs 4-wheel hydraulic pressure control, in order to maintain a constant low vehicle speed without causing the wheels to become locked. Thus, the vehicle can descend a steep hill in a stable manner.
CRAWL When the vehicle runs on extremely bumpy rough ground or a slippery road, the CRAWL is activated to regulate the engine output and the hydraulic pressure of the 4 wheels, allowing the driver to drive the vehicle at the desired speed and keep that speed with virtually no accelerator or brake pedal operation. As a result, off-road driveability is improved.

a.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, ensuring vehicle stability and excellent braking performance.

X133242E01
4.5,1.063 4.813,1.26 0.313,0.198 10 false *a 1.583,1.01 1.896,1.208 0.313,0.198 10 false *A: 1.594,2.385 1.906,2.583 0.313,0.198 10 false *B:

Text in Illustration (Illustration Provides Conceptual Image)
*A Models with ABS *B Models without ABS
*a Brake Operation - -



b.

Multi-terrain Anti-lock Brake System (Multi-terrain ABS)

i.

This function detects the off-road driving in sand, mud, gravel, dirt and so on based on signals from the yaw rate sensor, the speed sensor and the ECM, and then automatically switches to the ABS control most appropriate for the road condition.


ii.

This function is intended to improve the braking feeling when driving off-road without negatively affecting on-road braking control performance.

X114755E05
4.615,2.01 5.594,2.917 0.979,0.906 10 false Brake Hydraulic Control Signal 3.052,0.698 4.156,1.094 1.104,0.396 10 false Skid Control ECU 2.958,2.479 4.25,2.823 1.292,0.344 10 false Slip Rate Calculation 3.125,1.135 4.052,1.823 0.927,0.688 10 false Driving Surface Determination 0.25,0.583 1.979,0.99 1.729,0.406 10 false Multi-terrain Select Switch* 0.313,1.292 1.906,1.74 1.594,0.448 10 false Engine Output Information 0.281,2.021 1.875,2.417 1.594,0.396 10 false Vehicle Acceleration Rate 0.49,2.729 1.76,3.115 1.271,0.385 10 false Wheel Speed Signal 5.771,2.438 6.958,3.417 1.188,0.979 10 false Hydraulic Brake Booster Assembly 4.76,3.281 6.927,3.604 2.167,0.323 10 false *: Models with multi-terrain select

X102093E08
1.906,4.25 2.167,4.615 0.26,0.365 10 false Off 0.427,3.167 1.729,3.563 1.302,0.396 10 false Dry Road Driving 0.427,3.906 1.542,4.677 1.115,0.771 10 false Brake Hydraulic Pressure Control 1.927,3.885 2.25,4.208 0.323,0.323 10 false On 1.917,2.156 2.229,2.469 0.313,0.313 10 false Off 0.417,1.104 1.938,1.521 1.521,0.417 10 false Rough Road Driving 0.417,1.854 1.531,2.708 1.115,0.854 10 false Brake Hydraulic Pressure Control 1.938,1.802 2.25,2.125 0.313,0.323 10 false On 0.156,0.125 4.375,0.563 4.219,0.438 10 false Brake Hydraulic Pressure Control Image of Multi-terrain ABS



c.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

X102063E09
5.063,0.563 6.302,0.958 1.24,0.396 10 false : EBD control 3.625,1.115 4.385,1.948 0.76,0.833 10 false Rear Brake Force 4.854,1.906 6.302,2.302 1.448,0.396 10 false Front Brake Force 5.052,0.198 6.99,0.563 1.938,0.365 10 false : Ideal brake force distribution 0.156,0.094 3.25,0.573 3.094,0.479 10 false EBD Control Concept (without Load in Rear)

X102064E09
5.063,0.552 6.188,0.917 1.125,0.365 10 false : EBD control 3.615,1.177 4.365,2.021 0.75,0.844 10 false Rear Brake Force 4.802,1.896 6.219,2.323 1.417,0.427 10 false Front Brake Force 5.042,0.177 6.969,0.563 1.927,0.385 10 false : Ideal brake force distribution 0.156,0.073 2.969,0.563 2.813,0.49 10 false EBD Control Concept (with Load in Rear)


ii.

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions. This ensures vehicle stability and excellent braking performance.

X102065

Text in Illustration
V100136

Control Moment
V100135

Brake Force



d.

Brake Assist

i.

During brake assist, the skid control ECU calculates the speed of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the hydraulic brake booster assembly to increase the brake fluid pressure, which increases the brake force.

X102094E05
0.802,3.115 3.76,3.583 2.958,0.469 10 false Fluid Pressure Increased by Brake Actuator 0.99,0.5 2.188,0.844 1.198,0.344 10 false Skid Control ECU 0.948,1.281 2.146,1.927 1.198,0.646 10 false Hydraulic Brake Booster Assembly 4.052,0.729 4.51,1.563 0.458,0.833 10 false Brake Force 5.479,2.667 5.99,3.021 0.51,0.354 10 false Time 5.094,1.281 6.438,1.677 1.344,0.396 10 false With Brake Assist 4.948,2.01 6.365,2.469 1.417,0.458 10 false Without Brake Assist



e.

Traction Control (TRC)

i.

TRC helps prevent the drive wheels from slipping when the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Simultaneously with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to perform engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.

X102066E07
5.01,1.469 4.521,1.469 true 5.01,1.052 4.521,1.052 true 6.115,0.667 5.458,0.667 true 6.115,1.906 5.458,1.906 true 4.344,1.365 4.635,1.667 0.292,0.302 10 false *2 2.667,0.26 3,0.573 0.333,0.313 12 false *B: 1.063,0.281 1.385,0.563 0.323,0.281 12 false *A: 4.344,0.958 4.573,1.24 0.229,0.281 10 false *1 6.146,0.563 6.385,0.938 0.24,0.375 10 false *a 6.135,1.813 6.438,2.135 0.302,0.323 10 false *a

Text in Illustration (Driving on Road with Different Surface Friction Characteristics)
*A Models without TRC *B Models with TRC
*1 ECM
- Engine Output Control
*2 Hydraulic Brake Booster Assembly
- Hydraulic Brake Control
*a Brake Slipping Drive Wheel - -
V100145

Slippery Surface - -



f.

Active Traction Control (A-TRC)

i.

A-TRC helps restrain wheelspin by controlling the brake hydraulic pressure that is applied to the spinning wheels, and distributes the drive force that would have been lost through the slippage to the remaining wheels in order to achieve an effect that is similar to Limited Slip Differential (LSD).


ii.

A-TRC independently controls the brake hydraulic pressure to the 4 wheels in accordance with the extent of the slippage at the wheels, as detected by the skid control ECU.

X102095E06
5.417,0.771 5.635,0.771 true 5.167,0.219 4.948,0.219 4.948,0.219 4.948,0.667 true 1.688,2.688 1.896,2.688 true 2.552,3.281 2.333,3.281 2.333,3.281 2.333,2.833 true 5.229,0.125 6.229,0.49 1,0.365 10 false Braking 2.99,2 4.208,2.698 1.219,0.698 10 false Hydraulic Brake Booster Assembly 3.396,0.979 3.896,1.344 0.5,0.365 10 false Engine 5.698,0.677 6.948,1.031 1.25,0.354 10 false Slippery Surface 0.615,2.583 1.729,2.979 1.115,0.396 10 false Slippery Surface 2.604,3.188 3.406,3.594 0.802,0.406 10 false Braking 4.813,2.906 5.448,3.281 0.635,0.375 10 false Traction 2.094,0.25 2.854,0.573 0.76,0.323 10 false Traction 0.125,0.115 1.271,0.625 1.146,0.51 12 false w/ A-TRC:

X102096E06
5.448,0.802 5.667,0.802 true 1.688,2.688 1.896,2.688 true 3.406,0.948 3.917,1.375 0.51,0.427 10 false Engine 5.708,0.708 6.896,1.135 1.188,0.427 10 false Slippery Surface 0.635,2.563 1.74,2.958 1.104,0.396 10 false Slippery Surface 5.156,2.208 6.26,2.615 1.104,0.406 10 false No Traction 1.365,0.927 2.167,1.385 0.802,0.458 10 false No Traction 0.125,0.094 1.219,0.563 1.094,0.469 12 false w/o A-TRC:



g.

Vehicle Stability Control (VSC)

i.

The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. VSC is designed to help control vehicle behavior by controlling the engine output and the brakes of each wheel when the vehicle is under one of the conditions indicated below:

X102067E04
4.646,2.271 4.927,2.594 0.281,0.323 10 false *b 2.146,2.302 2.396,2.604 0.25,0.302 10 false *a

Text in Illustration
*a Front Wheel Skid Tendency (Understeer)
- When the front wheels lose grip in relation to the rear wheel
*b Rear Wheel Skid Tendency (Oversteer)
- When the rear wheels lose grip in relation to the front wheels


ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, yaw rate and lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (which is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X102068E05
3.708,0.094 3.948,0.365 0.24,0.271 10 false *a 4.938,0.969 5.208,1.26 0.271,0.292 10 false *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate


iv.

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X133244E01
3.51,0.073 3.823,0.271 0.313,0.198 10 false *a 3.958,0.167 4.271,0.365 0.313,0.198 10 false *b 4.229,0.531 4.542,0.729 0.313,0.198 10 false *c

Text in Illustration
*a Travel Direction of Vehicle's Center of Gravity *b Movement of Vehicle
*c Slip Angle - -


v.

When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies brakes to the front or rear wheels to control the vehicle's yaw moment. The basic operation of VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies brakes to the rear wheels and front wheel on the outer circle of the turn in order to help restrain the front wheel skid tendency.

X102070

Text in Illustration (Front Wheel Skid Dampening at Right Turn)
V100136

Control Moment
V100135

Brake Force


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies brakes to the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies brakes to the front wheel on the outer circle of the turn, as necessary.

X102071

Text in Illustration (Rear Wheel Skid Dampening at Right Turn)
V100136

Control Moment
V100135

Brake Force



h.

Trailer Sway Control

i.

If the vehicle is towing a trailer with an inappropriate hitch load, trailer sway could be caused by crosswinds, imbalance caused by load or the driver's steering. Trailer sway control reduces trailer sway by controlling the engine output and the braking of each wheel.

X112412E03
0.26,0.156 2.229,0.573 1.969,0.417 10 false Without Trailer Sway Control 0.26,2 2.26,2.365 2,0.365 10 false With Trailer Sway Control 0.375,1.438 1.188,1.823 0.813,0.385 10 false Side Wind 0.375,3.188 1.208,3.604 0.833,0.417 10 false Side Wind 3.385,3.083 5.906,3.583 2.521,0.5 10 false Brake Control + Engine Output Control

NOTICE:
·

Trailer sway control is a part of the VSC function. Accordingly, if the VSC OFF mode or VSC is not functioning normally, trailer sway control will not operate.

·

Trailer sway control will be unable to stabilize the vehicle if a trailer is being towed which cannot be physically controlled due to the influence of the vehicle, road surface, driving conditions and so on.




ii.

The skid control ECU detects the occurrence of trailer sway based on signals from the yaw rate sensor and the steering angle sensor.


iii.

Trailer sway can be reduced by decelerating the vehicle. When the skid control ECU detects trailer sway, it controls the brakes of each wheel while simultaneously requesting engine output control from the ECM and reducing vehicle speed.


iv.

Moreover, by using brake control to reduce the yaw moment caused by trailer sway, trailer sway can be reduced more quickly than by simply decelerating the vehicle.


v.

The slip indicator light on the combination meter assembly flashes when trailer sway control is in operation. Also, the stop light illuminates to inform vehicles behind that the vehicle is decelerating.

X112413E03
2.125,1.031 2.365,1.323 0.24,0.292 10 false *a 3.74,1.219 4.031,1.51 0.292,0.292 10 false *b 5.146,2 5.396,2.281 0.25,0.281 10 false *c 5.5,1.354 5.76,1.594 0.26,0.24 10 false *d

Text in Illustration
*a Trailer Sway *b Deceleration Force Caused by Brake Control and Engine Output Control
*c Yaw Moment Caused by Trailer Sway *d Control Moment Caused by Brake Control

X112414E03
4.385,0.49 4.385,0.292 4.385,0.292 4.792,0.292 false 3.5,1.219 3.906,1.219 3.906,1.219 3.906,1.021 false 0.271,0.542 1.625,1.292 1.354,0.75 10 false Yaw Rate and Lateral Acceleration 0.271,1.531 1.74,1.927 1.469,0.396 10 false Trailer Sway Control 0.271,2.24 1.292,2.594 1.021,0.354 10 false Brake Force 0.281,3.021 1.333,3.406 1.052,0.385 10 false Yaw Moment 0.302,3.99 1.354,4.375 1.052,0.385 10 false Vehicle Speed 6.542,0.74 7.042,1.125 0.5,0.385 10 false Time 6.542,1.698 6.979,2.052 0.438,0.354 10 false Time 6.552,2.333 7,2.677 0.448,0.344 10 false Time 6.542,3.115 6.99,3.427 0.448,0.313 10 false Time 6.542,4.385 6.99,4.698 0.448,0.313 10 false Time 4.844,0.198 6.281,0.604 1.438,0.406 10 false Lateral Acceleration 2.844,1.115 3.552,1.479 0.708,0.365 10 false Yaw Rate 4.323,1.385 4.594,1.677 0.271,0.292 10 false On 5.802,1.813 6.135,2.104 0.333,0.292 10 false Off



i.

Hill-start Assist Control

i.

When the vehicle starts off on a steep or slippery hill, the vehicle may start to descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, hill-start assist control temporarily (approximately 5 seconds at the maximum) applies brakes to the 4 wheels in order to prevent the vehicle from descending backward.


ii.

Without hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With hill-start assist control, however, the driver can start off easily and operate the pedal in a relaxed manner, because hill-start assist control prevents the vehicle from descending backward.

X102097E06
4.156,3.333 6.417,3.719 2.26,0.385 10 false Without Hill-start Assist Control 4.542,2.938 6.979,3.313 2.438,0.375 10 false Increases backward speed of vehicle 1.167,3.313 3.146,3.677 1.979,0.365 10 false With Hill-start Assist Control 5.333,0.198 6.479,0.615 1.146,0.417 10 false Difficult Control 2.146,0.292 3.26,0.719 1.115,0.427 10 false Easy Control 1.073,2.938 3.521,3.302 2.448,0.365 10 false Reduces backward speed of vehicle



j.

Downhill Assist Control

i.

When the vehicle is descending a steep hill and the engine brake alone cannot provide a sufficient deceleration force while the transfer drive mode is in L4F or L4L, downhill assist control performs 4 wheel brake control to maintain a constant, low vehicle speed. Thus, the vehicle is able to descend in a stable manner without causing the wheels to lock.


ii.

When the vehicle descends a steep hill without downhill assist control, the driver must pay close attention to brake and accelerator pedal maneuvers. However, with downhill assist control, the driver can concentrate on the steering operation, without accelerator or brake pedal operation.


iii.

Downhill assist control enables the vehicle to maintain stability because it can descend a slippery hill at low speeds without causing the wheels to lock.

X102098E05
4.469,4.292 6.813,4.698 2.344,0.406 10 false Without Downhill Assist Control 3.219,0.208 4.302,0.615 1.083,0.406 10 false Difficult Control 0.438,0.229 1.354,0.625 0.917,0.396 10 false Easy Control 0.271,1.51 1.281,2.323 1.01,0.813 10 false No Braking and No Accelerating 0.917,3.604 2,3.958 1.083,0.354 10 false Stable Speed 3.76,3.958 5.052,4.292 1.292,0.333 10 false Unstable Speed 1.073,4.271 2.948,4.656 1.875,0.385 10 false With Downhill Assist Control



k.

CRAWL

i.

The CRAWL is a driving support system that regulates the engine output and the brake force, enabling the vehicle to be driven at a constant speed on rough ground or slippery roads.


ii.

When the vehicle drives across rough ground such as extremely bumpy rough roads, the driver needs to pay attention to the steering, braking and acceleration operations. However, with the CRAWL, the driver can concentrate on steering, without worrying about the accelerator pedal or brake pedal.

HINT:

If the accelerator pedal is depressed during CRAWL control, AUTO mode for the multi-terrain select turns on automatically. Also, the multi-terrain select on/off switch cannot be operated during CRAWL control.


X102099


iii.

The CRAWL ensures good vehicle stability in situations such as when the vehicle is running on a slippery or steep road because the chances of the wheels spinning or locking are minimized by regulating the engine output and the brake force.

X102100


iv.

The driver is informed of CRAWL operation by the flashing or illumination of the CRAWL indicator, the multi-terrain select indicator and the slip indicator light. Also, operation condition are displayed on the multi-information display.

System Condition Indicator Light Multi-information Display
Slip Indicator Light CRAWL Indicator Multi-terrain Select Indicator Display

○: Illuminates

▲: Blinks

X: Turns off

CRAWL Control is Operating and Accelerator Pedal is Not Depressed ▲ or X ○ X Shows the operating condition of CRAWL control
CRAWL Control is Operating and Accelerator Pedal is Depressed ▲ or X X ○ Shows the operation condition of the multi-terrain select (MTS AUTO)




FUNCTION


a.

VSC OFF Switch

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, engine output control is stopped to maintain drive torque.

HINT:

The VSC OFF switch cannot be operated while multi-terrain select is operating.


Models without Multi-terrain Select or Rear Air Suspension System
X138229C01
1.333,0.979 0.958,0.313 true 6.208,1.219 6.448,0.802 true 6.229,2.719 6.469,2.302 true 0.823,0.104 1.135,0.26 0.313,0.156 10 false *1 6.406,0.604 6.719,0.76 0.313,0.156 10 false *2 6.448,2.115 6.76,2.271 0.313,0.156 10 false *2 4.417,0.615 4.729,0.771 0.313,0.156 10 false *A: 4.375,2.146 4.688,2.302 0.313,0.156 10 false *B:
*A Models with Automatic Transmission *B Models with Manual Transmission
*1 Combination Meter Assembly
·

VSC OFF Indicator Light

·

TRC OFF Indicator Light


*2 VSC OFF Switch


Models with Multi-terrain Select or Rear Air Suspension System
X138230C01
1.323,1 0.99,0.26 true 5.271,1.156 5.531,0.771 true 0.854,0.073 1.167,0.229 0.313,0.156 10 false *1 5.521,0.563 5.833,0.719 0.313,0.156 10 false *2
*1 Combination Meter Assembly
·

VSC OFF Indicator Light

·

TRC OFF Indicator Light


*2 VSC OFF Switch



ii.

The VSC OFF switch can select 3 modes (mode A, mode B and mode C).


iii.

Briefly pressing the VSC OFF switch in mode A selects mode B.


iv.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects mode C.


v.

Briefly pressing the VSC OFF switch in mode B or mode C or turning the engine switch off returns to mode A.


vi.

When TRC is not operating, the TRC OFF indicator light will illuminate.


vii.

When VSC is not operating, the VSC OFF indicator light will illuminate.

X102072E08
4.604,0.781 6.469,1.927 1.865,1.146 10 false : VSC OFF switch operation (press and hold for 3 seconds or more) 4.583,0.271 7.052,0.688 2.469,0.417 10 false : VSC OFF switch operation (briefly) 0.833,1.792 1.677,2.156 0.844,0.365 10 false Mode C 2.229,0.625 3.094,0.99 0.865,0.365 10 false Mode A 3.625,1.792 4.469,2.156 0.844,0.365 10 false Mode B

Function of VSC OFF Switch (Models without Multi-terrain Select)
Transfer Drive Mode Brake Control Function VSC OFF Switch Mode
Mode A Mode B Mode C
H4F TRC Operates Does Not Operate Does Not Operate
A-TRC Does Not Operate Does Not Operate Does Not Operate
VSC Operates Operates Does Not Operate
H4L TRC Operates Does Not Operate Does Not Operate
A-TRC Does Not Operate Does Not Operate Does Not Operate
VSC Operates Operates Does Not Operate
L4F TRC Does Not Operate - Does Not Operate
A-TRC Operates - Does Not Operate
VSC Operates - Does Not Operate
L4L TRC Does Not Operate - Does Not Operate
A-TRC Operates - Does Not Operate
VSC Does Not Operate - Does Not Operate

Function of VSC OFF Switch (Models with Multi-terrain Select)
Transfer Drive Mode Brake Control Function VSC OFF Switch Mode
Mode A Mode B Mode C
H4F TRC Operates Does Not Operate Does Not Operate
A-TRC Does Not Operate Does Not Operate Does Not Operate
VSC Operates Operates Does Not Operate
H4L TRC Operates Does Not Operate Does Not Operate
A-TRC Does Not Operate Does Not Operate Does Not Operate
VSC Operates Operates Does Not Operate
L4F TRC Does Not Operate - Does Not Operate
A-TRC Does Not Operate - Does Not Operate
VSC Operates - Does Not Operate
L4L TRC Does Not Operate - Does Not Operate
A-TRC Does Not Operate - Does Not Operate
VSC Does Not Operate - Does Not Operate



b.

Multi-terrain Select

i.

The multi-terrain select is used when off-road driving on various types of road surfaces.


ii.

When CRAWL control is off, switching the drive mode to L4 and operating the multi-terrain select on/off switch resume multi-terrain select control. 5 modes (MUD & SAND, LOOSE ROCK, MOGUL, ROCK & DIRT and ROCK) are selectable according to each type of the road surface and an optimal A-TRC brake control is switched to automatically, achieving superior off-road driving performance.

·

The multi-terrain select has the following functions:

Multi-terrain Select Function Sends the road mode that is selected by the multi-terrain select road mode selector to the skid control ECU, ECM and 4WD control ECU.
According to the selected road mode, an optimal engine output control and A-TRC brake control are switched to automatically.

·

The screen of the multi-information display is switched by operating the multi-terrain select switch and multi-terrain select road mode selector, control is enabled by determining the road mode, and the multi-terrain select indicator illuminates.

X138232C01
1.458,1.073 1.156,0.448 true 5.479,2.021 5.031,1.375 true 6.125,1.823 6.417,1.406 true 1.031,0.208 1.344,0.365 0.313,0.156 10 false *1 4.896,1.198 5.208,1.354 0.313,0.156 10 false *2 6.417,1.229 6.729,1.385 0.313,0.156 10 false *3 5.427,2.969 5.74,3.125 0.313,0.156 10 false *4
*1 Combination Meter Assembly
·

Multi-terrain Select Indicator

·

Multi-information Display


*2 Multi-terrain Select Road Mode Selector
*3 Multi-terrain Select Switch *4 Module Switch


·

5 road modes can be selected: "MUD & SAND", "LOOSE ROCK", "MOGUL", "ROCK & DIRT" and "ROCK". The recommended road modes for each condition are listed below.

HINT:

Road mode recommendations are for reference only. The mode may not be appropriate depending on the road conditions (incline, road surface, road undulation, etc.).

X114758E03
1.656,2.094 2.688,2.51 1.031,0.417 10 false MUD & SAND 4.688,2.198 5.896,2.594 1.208,0.396 10 false LOOSE ROCK 3.271,4.094 3.99,4.531 0.719,0.438 10 false MOGUL 1.781,6.333 2.823,6.698 1.042,0.365 10 false ROCK & DIRT 5.094,6.354 5.729,6.719 0.635,0.365 10 false ROCK


X114759E04
3.917,0.188 6.135,0.51 2.219,0.323 10 false Multi-terrain Select Road Mode 0.135,3.063 2.542,3.365 2.406,0.302 10 false Uneven Surfaces and Grooved Areas 0.135,2.74 2.479,3.052 2.344,0.313 10 false Crossing Rivers 0.135,2.427 1.51,2.729 1.375,0.302 10 false Deep Snow 0.135,2.104 1.646,2.385 1.51,0.281 10 false Rocky Terrain 0.135,1.792 1.469,2.104 1.333,0.313 10 false Moguls 0.146,1.469 1.5,1.76 1.354,0.292 10 false Pebbles 0.146,1.156 1.417,1.448 1.271,0.292 10 false Sand 0.135,0.833 1.51,1.135 1.375,0.302 10 false Muddy Road 0.146,3.375 2.5,3.677 2.354,0.302 10 false Crossing Inclines and Grooved Areas 0.135,3.698 2.031,4 1.896,0.302 10 false Uphill and Downhill 0.135,4 2.531,4.333 2.396,0.333 10 false Undergrowth 0.146,4.323 1.156,4.635 1.01,0.313 10 false Dirt Road 0.771,0.417 2.073,0.781 1.302,0.365 10 false Road Condition 2.823,0.51 3.333,0.813 0.51,0.302 10 false Rock 3.51,0.521 4.323,0.823 0.813,0.302 10 false Rock & Dirt 4.583,0.51 5.115,0.833 0.531,0.323 10 false Mogul 5.302,0.51 6.125,0.813 0.823,0.302 10 false Loose Rock 6.167,0.521 7.031,0.823 0.865,0.302 10 false Mud & Sand

·

The engine output and A-TRC control tendency for each road mode are as follows:

Multi-terrain Select Road Mode Transfer Drive Mode Control
A-TRC Control Results
Mud and Sand L4 The wheels are allowed to slip more than usual. Outputs a large amount of drive force and suppresses deceleration feeling by assuming that the vehicle is driving on a soft, slippery road surface.
Loose Rock L4 The wheels are allowed to slip more than usual. Outputs a large amount of drive force and suppresses deceleration feeling by assuming that the vehicle is driving on slippery or loose-graveled uphill slopes.
Mogul L4 The wheels are allowed to slip more than usual. Suppresses deceleration feeling to achieve smooth driving on hills while improving the LSD function by assuming that the vehicle is driving on a highly bumpy road surface.
Rock and Dirt L4 The wheels are made to grip more than usual. Gives the wheels grip and improves the LSD function by assuming that the vehicle is driving on a highly bumpy road surface.
Rock L4 The wheels are made to grip more than usual. Gives the wheels grip and improves the LSD function by assuming that the vehicle is driving on a highly bumpy road surface.

·

The driver is informed of multi-terrain select operation by the flashing or illumination of the multi-terrain select indicator and the slip indicator light. Also, operation assist messages are displayed on the multi-information display.

System Condition Slip Indicator Light Multi-information Display
Multi-terrain Select Indicator Display Message

○: Illuminates

▲: Blinks

X: Turns off

Operates X ○ -
A-TRC Operates ▲ ○ -
A-TRC Control → A-TRC Control Released ▲ → X ○ → X MULTI-TERRAIN SELECT HAS BEEN CANCELLED
Control Commencement Conditions Not Met Transfer Drive Mode Mismatch X X SHIFT TO L4
During CRAWL Control ▲ ○ or X OPERATION NOT POSSIBLE WHEN CRAWL CONTROL ACTIVATED
Malfunction Multi-terrain Select X ▲ MULTI-TERRAIN SELECT NOT AVAILABLE
Related System Switching Commencement Conditions Not Met X ○ OPERATION NOT POSSIBLE WHEN MULTI-TERRAIN SELECT ACTIVATED
Operation Assist X ○ or ▲ or X STOP THE VEHICLE AND SHIFT THE AUTOMATIC TRANSMISSION TO N



iii.

When acceleration pedal operation is performed while CRAWL control is on, AUTO road surface mode is selected and multi-terrain select control resumes. When in AUTO mode, an optimal A-TRC brake control is switched to automatically according to the set vehicle speed, achieving superior off-road driving performance.

HINT:

Also, the multi-terrain select on/off switch cannot be operated during CRAWL control.





CONSTRUCTION


a.

Yaw Rate Sensor and Deceleration Sensor

i.

A yaw rate sensor and deceleration sensor are built into the center airbag sensor assembly.


ii.

The yaw rate sensor detects the vehicle's yaw rate.


iii.

The deceleration sensor detects the vehicle's longitudinal and lateral acceleration.

X137825C01
4.229,1 4.833,0.469 true 4.885,0.354 5.198,0.552 0.313,0.198 10 false *1
*1 Center Airbag Sensor Assembly
·

Yaw Rate Sensor

·

Deceleration Sensor


- -




b.

Steering Angle Sensor

i.

The steering angle sensor detects the steering direction and angle, and sends this information to the skid control ECU.

X137824C01
3.625,2.802 4.385,3.146 4.385,3.146 3.938,2.427 true 4.396,3.219 4.708,3.417 0.313,0.198 10 false *1
*1 Detection Gear - -




c.

Speed Sensor

i.

Active type speed sensors, which can detect the rotational direction of the wheel, have been provided. This type of sensor contains a Hall IC, which consists of 2 Magnetic Resistance Elements (MREs).


ii.

The magnet type rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.

X102137E04
2.365,0.594 3.042,0.594 true 5.813,1.417 6.479,1.417 true 3.073,0.5 3.302,0.792 0.229,0.292 10 false *1 6.51,1.313 6.771,1.646 0.26,0.333 10 false *2

Text in Illustration (Front Axle)
*1 Front Speed Sensor *2 Sensor Rotor

X102138E04
2.333,0.615 3.01,0.344 true 5.677,1.385 6.344,1.385 true 3.031,0.229 3.281,0.51 0.25,0.281 10 false *1 6.375,1.292 6.625,1.625 0.25,0.333 10 false *2

Text in Illustration (Rear Axle)
*1 Rear Speed Sensor *2 Sensor Rotor



d.

Stop Light Switch Assembly

i.

A non-contact type stop light switch assembly with high durability is used.


ii.

The movement of the magnet placed on the shaft is detected by the magnetic sensor.


iii.

2 magnetic sensors are installed and they output stop light illumination signals and cruise control system cancel signals.

X138222C01
3.125,2.448 2.917,1.896 true 3.073,2.5 3.385,2.656 0.313,0.156 10 false *1 5.198,2.469 5.51,2.625 0.313,0.156 10 false *a
*1 Stop Light Switch Assembly - -
*a Stop Light Switch Assembly Cross Section - -




e.

Hydraulic Brake Booster Assembly

i.

The brake actuator portion of the hydraulic brake booster consists of 4 switching solenoid valves, 8 control solenoid valves and a skid control ECU.


ii.

The pressure increase mode, the pressure holding mode, and the pressure reduction mode are performed based on the combination of these solenoid valves, which are turned on and off in order to control the hydraulic pressure that is applied to each of the wheel cylinders.


iii.

4 switching solenoid valves are used: 2 (SMCF, SREA) in the front brake fluid path, 1 (SREC) in the rear brake fluid path and 1 (STR) in the accumulator fluid path. The switching solenoid valves open and close in accordance with the control signals from the skid control ECU in order to switch the respective brake fluid path.


iv.

The 8 control solenoid valves are used for the 4 wheels (2 types per wheel: pressure holding solenoid and pressure reduction solenoid).

X102293

X102102E03
1.917,2.031 2.104,2.146 true 3.76,2.177 3.479,2.177 true 4.667,5.094 4.948,5.365 0.281,0.271 10 false *d 4.083,5.094 4.333,5.323 0.25,0.229 10 false *c 2.688,5.094 2.927,5.344 0.24,0.25 10 false *b 5.188,4.135 5.573,4.375 0.385,0.24 10 false *14 4.188,4.135 4.573,4.375 0.385,0.24 10 false *13 3.198,4.135 3.594,4.344 0.396,0.208 10 false *12 5.219,3.177 5.552,3.427 0.333,0.25 10 false *10 4.24,3.177 4.51,3.448 0.271,0.271 10 false *9 3.25,3.177 3.49,3.417 0.24,0.24 10 false *8 4.688,1.719 4.927,1.938 0.24,0.219 10 false *4 3.781,1.719 3.99,1.948 0.208,0.229 10 false *3 2.865,1.729 3.125,2 0.26,0.271 10 false *2 1.958,1.729 2.177,1.958 0.219,0.229 10 false *1 1.75,1.906 1.979,2.146 0.229,0.24 10 false *5 3.802,2.083 4.021,2.344 0.219,0.26 10 false *6 2.26,3.177 2.49,3.406 0.229,0.229 10 false *7 2.208,4.135 2.583,4.354 0.375,0.219 10 false *11 2.104,5.094 2.396,5.302 0.292,0.208 10 false *a

Text in Illustration
*1 Switching Solenoid Valve STR (Traction Solenoid Valve) *2 Switching Solenoid Valve SREC (Regulator Cut Solenoid Valve)
*3 Switching Solenoid Valve SREA (Regulator Apply for Front Solenoid Valve) *4 Switching Solenoid Valve SMCF (Master Cut for Front Solenoid Valve)
*5 Control Pressure Sensor (Models with Pre-crash Safety System) *6 Master Cylinder Pressure Sensor
*7 Control Solenoid Valve SRRH *8 Control Solenoid Valve SRLH
*9 Control Solenoid Valve SFRH *10 Control Solenoid Valve SFLH
*11 Control Solenoid Valve SRRR *12 Control Solenoid Valve SRLR
*13 Control Solenoid Valve SFRR *14 Control Solenoid Valve SFLR
*a Rear Brake LH *b Rear Brake RH
*c Front Brake LH *d Front Brake RH
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder - -




OPERATION


a.

Speed Sensor

i.

The active type speed sensor uses a sensor IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.

X102996E04
6.521,2.781 7.031,3.135 0.51,0.354 10 false Time 3.688,2.188 4.24,3.083 0.552,0.896 10 false Output Voltage 4.615,2.927 6.354,3.396 1.74,0.469 10 false Digital Pulse (Backward) 2.51,1.438 3.229,1.854 0.719,0.417 10 false Sensor IC 4.656,1.24 6.365,1.719 1.708,0.479 10 false Digital Pulse (Forward) 3.729,0.479 4.25,1.406 0.521,0.927 10 false Output Voltage 6.531,1.073 7.031,1.458 0.5,0.385 10 false Time 0.417,2.188 1.781,3.104 1.365,0.917 10 false Sensor Rotor (Bearing Inner Race)


ii.

To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by the 2 Magnetic Resistance Elements (MREs).


iii.

Upon receiving this signal, the Hall IC outputs a forward or backward wave.

X102079E08
2.771,2.146 3.76,2.531 0.99,0.385 10 false MRE B: Lo 0.167,0.177 0.979,0.5 0.813,0.323 10 false Forward 2.771,1.781 3.635,2.167 0.865,0.385 10 false MRE A: Hi 1.906,1.583 2.5,1.99 0.594,0.406 10 false MRE B 1.906,1.219 2.563,1.594 0.656,0.375 10 false MRE A

X102080E08
3.302,2.146 4.292,2.531 0.99,0.385 10 false MRE B: Hi 0.167,0.167 1.208,0.573 1.042,0.406 10 false Backward 3.302,1.781 4.292,2.167 0.99,0.385 10 false MRE A: Hi 1.906,1.583 2.542,1.969 0.635,0.385 10 false MRE B 1.906,1.219 2.604,1.604 0.698,0.385 10 false MRE A


iv.

The frequency of the output pulses is used to detect the vehicle speed. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X102081E08
1.427,1.75 2.51,2.229 1.083,0.479 10 false Sensor Output 1.438,0.635 2.5,1.021 1.063,0.385 10 false Vehicle Speed



b.

ABS and EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks wheel slipping conditions.


ii.

The skid control ECU compares the speed sensor signals of the front and rear, judges the slipping condition of the rear wheel and operates the EBD.


iii.

When a wheel is about to lock, the ABS operation starts in order to regulate the hydraulic pressure at the wheel cylinders while switching between the 3 modes: pressure increase, pressure holding and pressure reduction.

X102104E03
5.438,3.115 5.75,3 true 4.417,3.115 4.635,2.854 true 3.427,3.115 3.635,2.813 true 1.76,3.229 2.073,3.104 true 4.604,4.396 4.833,4.635 0.229,0.24 10 false *d 4.042,4.385 4.292,4.635 0.25,0.25 10 false *c 2.625,4.396 2.865,4.646 0.24,0.25 10 false *b 5.49,2.219 5.802,2.5 0.313,0.281 10 false *8 4.51,2.219 4.844,2.521 0.333,0.302 10 false *7 3.521,2.208 3.823,2.438 0.302,0.229 10 false *6 4.625,1.396 4.885,1.635 0.26,0.24 10 false *4 3.729,1.406 3.99,1.635 0.26,0.229 10 false *3 2.823,1.406 3.083,1.625 0.26,0.219 10 false *2 1.896,1.406 2.135,1.625 0.24,0.219 10 false *1 2.521,2.208 2.833,2.469 0.313,0.26 10 false *5 5.771,2.875 6.094,3.167 0.323,0.292 10 false *12 4.542,2.667 4.844,2.896 0.302,0.229 10 false *11 3.542,2.615 3.875,2.844 0.333,0.229 10 false *10 1.573,3.146 1.813,3.438 0.24,0.292 10 false *9 2.052,4.396 2.302,4.677 0.25,0.281 10 false *a

EBD Operation
Item EBD Not Activated EBD Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) ← ← ←
*2 SREC Off (Open) ← ← ←
*3 SREA Off (Closed) ← ← ←
*4 SMCF Off (Open) ← ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) On (Closed) ← ←
*9 SRLR Off (Closed) ← ← ←
*a Wheel Cylinder Pressure - - - -
Rear Brake RH *6 SRRH Off (Open) On (Closed) ← ←
*10 SRRR Off (Closed) ← ← ←
*b Wheel Cylinder Pressure - - - -
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder

X102105E04
5.427,3.104 5.74,2.99 true 4.417,3.104 4.635,2.844 true 3.417,3.094 3.625,2.792 true 1.76,3.24 2.073,3.115 true 4.583,4.396 4.896,4.667 0.313,0.271 10 false *d 4.031,4.396 4.271,4.656 0.24,0.26 10 false *c 2.615,4.396 2.917,4.625 0.302,0.229 10 false *b 5.49,2.208 5.792,2.448 0.302,0.24 10 false *8 4.5,2.219 4.802,2.448 0.302,0.229 10 false *7 3.521,2.229 3.833,2.521 0.313,0.292 10 false *6 4.635,1.396 4.906,1.646 0.271,0.25 10 false *4 3.729,1.406 3.948,1.646 0.219,0.24 10 false *3 2.823,1.406 3.021,1.646 0.198,0.24 10 false *2 1.896,1.406 2.094,1.646 0.198,0.24 10 false *1 2.521,2.219 2.813,2.469 0.292,0.25 10 false *5 5.76,2.906 6.083,3.188 0.323,0.281 10 false *12 4.552,2.656 4.854,2.885 0.302,0.229 10 false *11 3.542,2.594 3.917,2.833 0.375,0.24 10 false *10 1.583,3.146 1.885,3.375 0.302,0.229 10 false *9 2.052,4.385 2.281,4.656 0.229,0.271 10 false *a

ABS Operation
Item ABS Not Activated ABS Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) ← ← ←
*2 SREC Off (Open) ← ← ←
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder

HINT:

While the front wheels are in the ABS operation, SREA and SMCF are on. While only rear wheels are in the ABS operation, SREA and SMCF are off.




c.

Multi-terrain ABS

i.

The skid control ECU calculates the speed and deceleration of each wheel, and checks the wheel slipping condition based on signals from the 4 speed sensors and the yaw rate sensor as well as the engine output information transmitted from the ECM.


ii.

If the wheel is likely to lock, the skid control ECU controls the pressure holding solenoid valve and pressure reduction solenoid valve as multi-terrain ABS operation in the following 3 modes: increase mode, holding mode and reduction mode.

X102105E04
5.427,3.104 5.74,2.99 true 4.417,3.104 4.635,2.844 true 3.417,3.094 3.625,2.792 true 1.76,3.24 2.073,3.115 true 4.583,4.396 4.896,4.667 0.313,0.271 10 false *d 4.031,4.396 4.271,4.656 0.24,0.26 10 false *c 2.615,4.396 2.917,4.625 0.302,0.229 10 false *b 5.49,2.208 5.792,2.448 0.302,0.24 10 false *8 4.5,2.219 4.802,2.448 0.302,0.229 10 false *7 3.521,2.229 3.833,2.521 0.313,0.292 10 false *6 4.635,1.396 4.906,1.646 0.271,0.25 10 false *4 3.729,1.406 3.948,1.646 0.219,0.24 10 false *3 2.823,1.406 3.021,1.646 0.198,0.24 10 false *2 1.896,1.406 2.094,1.646 0.198,0.24 10 false *1 2.521,2.219 2.813,2.469 0.292,0.25 10 false *5 5.76,2.906 6.083,3.188 0.323,0.281 10 false *12 4.552,2.656 4.854,2.885 0.302,0.229 10 false *11 3.542,2.594 3.917,2.833 0.375,0.24 10 false *10 1.583,3.146 1.885,3.375 0.302,0.229 10 false *9 2.052,4.385 2.281,4.656 0.229,0.271 10 false *a

Multi-terrain ABS Operation
Item Multi-terrain ABS Not Activated Multi-terrain ABS Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) ← ← ←
*2 SREC Off (Open) ← ← ←
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder

HINT:

While the front wheels are in the multi-terrain ABS operation, SREA and SMCF are on. While only rear wheels are in the multi-terrain ABS operation, SREA and SMCF are off.




d.

Brake Assist

i.

If an emergency braking situation has occurred, it is detected by the skid control ECU based on the vehicle speed signal from the speed sensor, the brake pedal application speed from the master cylinder pressure sensor, and the signal representing the amount of pedal effort. Then, the skid control ECU actuates each solenoid valve. As a result, the pressure from the brake booster accumulator assembly is applied to the wheel cylinders. The accumulator pressure that is applied to the wheel cylinders generates a higher pressure than the master cylinder.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

Brake Assist Operation
Item Brake Assist Not Activated Brake Assist Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



e.

TRC

i.

The fluid pressure that is generated by the brake booster pump assembly is regulated by the switching solenoid valves and control solenoid valves to the required pressure. Thus, the pressure to the wheel cylinders of the drive wheels is controlled in the following 3 modes: increase mode, holding mode and reduction mode, to restrain the slippage of the drive wheels.


ii.

The skid control ECU outputs a TRC operation signal to the ECM. Upon receiving this signal, the ECM performs engine output control.


iii.

If the accumulator pressure drops during this operation, the skid control ECU receives the signals from the accumulator pressure sensor and actuates the brake booster pump assembly to ensure the proper accumulator pressure.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

TRC Operation
Item TRC Not Activated TRC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



f.

A-TRC

i.

Based on the vehicle speed that has been calculated from each speed sensor and the signals of the yaw rate and deceleration sensors, the skid control ECU computes the target control speed.


ii.

The skid control ECU compares the target control speed and the wheel speed to determine whether or not slippage exists. Upon detecting slippage, the skid control ECU controls the solenoid valve of the hydraulic brake booster assembly to control the brake fluid pressure that is applied to the slipping wheel. When the wheel speed becomes lower than the target control speed, the skid control ECU stops increasing the brake fluid pressure.


iii.

Fluid pressure control of the A-TRC independently controls the brake of each wheel by operating the individual solenoid valves in accordance with the signals received from the skid control ECU. The brake of each wheel is controlled in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

A-TRC Operation
Item A-TRC Not Activated A-TRC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



g.

VSC

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines the vehicle's yaw moment. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes. As a result, the tendency of the front wheels or the rear wheels to skid is restrained.


ii.

At this time, the skid control ECU outputs a VSC operation signal to the ECM and the combination meter and causes the buzzer in the combination meter assembly to sound intermittently. Upon receiving this signal, the ECM controls the engine output. The slip indicator light will blink in the combination meter assembly.


iii.

During front wheel skid restraining control, brakes of the rear wheels and front wheel of the outer side of the turn are applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which a brake might not be applied to the wheels even if those wheels are targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a front wheel skid while the vehicle is making a right turn.

X102297E03
5.427,3.135 5.74,3.021 true 4.417,3.083 4.635,2.823 true 3.427,3.135 3.635,2.833 true 1.76,3.25 2.073,3.125 true 4.604,4.396 4.896,4.688 0.292,0.292 10 false *d 4.042,4.396 4.313,4.656 0.271,0.26 10 false *c 2.625,4.396 2.896,4.625 0.271,0.229 10 false *b 5.49,2.219 5.771,2.51 0.281,0.292 10 false *8 4.51,2.229 4.813,2.458 0.302,0.229 10 false *7 3.521,2.229 3.823,2.458 0.302,0.229 10 false *6 4.635,1.385 4.865,1.615 0.229,0.229 10 false *4 3.729,1.406 4.01,1.729 0.281,0.323 10 false *3 2.74,1.406 3.01,1.698 0.271,0.292 10 false *2 1.906,1.406 2.146,1.688 0.24,0.281 10 false *1 2.521,2.219 2.844,2.469 0.323,0.25 10 false *5 5.76,2.896 6.083,3.198 0.323,0.302 10 false *12 4.552,2.615 4.875,2.865 0.323,0.25 10 false *11 3.594,2.656 3.906,2.917 0.313,0.26 10 false *10 1.583,3.167 1.844,3.438 0.26,0.271 10 false *9 2.052,4.396 2.323,4.677 0.271,0.281 10 false *a

VSC Operation (Turning Right)
Item VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) On (Closed) ← ←
*12 SFRR Off (Closed) ← ← ←
*d Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder


iv.

During rear wheel skid restraining control, the front wheel brake of the outer side of the turn is applied. Also, depending on whether the brake is on or off and on the condition of the vehicle, there are circumstances in which a brake might be applied to the rear brake of the outer side of the turn. The diagram below shows the hydraulic circuit in the pressure increase mode, as it restrains a rear wheel skid while the vehicle is making a right turn.

X102298E03
5.427,3.125 5.74,3.01 true 4.406,3.094 4.625,2.833 true 3.427,3.115 3.635,2.813 true 1.76,3.25 2.073,3.125 true 4.583,4.396 4.885,4.625 0.302,0.229 10 false *d 4.031,4.396 4.25,4.677 0.219,0.281 10 false *c 2.615,4.385 2.917,4.615 0.302,0.229 10 false *b 5.49,2.208 5.74,2.479 0.25,0.271 10 false *8 4.521,2.229 4.781,2.458 0.26,0.229 10 false *7 3.521,2.24 3.823,2.531 0.302,0.292 10 false *6 4.625,1.385 4.844,1.625 0.219,0.24 10 false *4 3.729,1.406 4.01,1.698 0.281,0.292 10 false *3 2.74,1.406 2.979,1.688 0.24,0.281 10 false *2 1.896,1.406 2.135,1.635 0.24,0.229 10 false *1 2.521,2.229 2.823,2.5 0.302,0.271 10 false *5 5.76,2.906 6.115,3.167 0.354,0.26 10 false *12 4.542,2.646 4.865,2.896 0.323,0.25 10 false *11 3.542,2.625 3.906,2.854 0.365,0.229 10 false *10 1.573,3.156 1.823,3.448 0.25,0.292 10 false *9 2.052,4.396 2.281,4.646 0.229,0.25 10 false *a

VSC Operation (Turning Right)
Item VSC Not Activated VSC Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) On (Closed) ← ←
*12 SFRR Off (Closed) ← ← ←
*d Wheel Cylinder Pressure - - - -
Rear Brake LH *5 SRLH Off (Open) On (Closed) ← ←
*9 SRLR Off (Closed) ← ← ←
*a Wheel Cylinder Pressure - - - -
Rear Brake RH *6 SRRH Off (Open) On (Closed) ← ←
*10 SRRR Off (Closed) ← ← ←
*b Wheel Cylinder Pressure - - - -
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



h.

Hill-start Assist Control

i.

Based on the information provided by various sensors, switches, and the ECM, the skid control ECU computes the backward movement of the vehicle that occurs when the vehicle starts off on a hill. Then, the skid control ECU controls the fluid pressure that is generated by the pump and pump motor and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.


ii.

The skid control ECU determines the state of the backward movement of the vehicle while the driver is attempting to drive uphill, based on the speed sensors and the neutral start switch.


iii.

The skid control ECU determines the gradient of the hill, the acceleration state of the vehicle, the locked state and the rotation direction of each wheel through the speed sensors and the yaw rate sensor. Then, the skid ECU computes the amount of brake control that will prevent the wheels from locking.


iv.

During this operation, the skid control ECU outputs a hill-start assist control operation signal to the combination meter. This causes the slip indicator light to blink, sends signals to the stop light control relay which turns on the stop light.


v.

Hill-start assist control operates for approximately 5 seconds. At this time, the skid control ECU informs the driver by the slow and intermittent sound of the buzzer in the combination meter assembly. After this, the skid control ECU alerts the driver by using the quick and intermittent sound of the buzzer in the combination meter assembly, and gradually releases the brake hydraulic pressure in order to end the hill-start assist control operation.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

Hill-start Assist Control Operation
Item Hill-start Assist Control Not Activated Hill-start Assist Control Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



i.

Downhill Assist Control

i.

Based on the information provided by various sensors, switches and the engine ECU, the skid control ECU determines the conditions that enable downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.


ii.

The skid control ECU computes the vehicle speed, travel direction and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate sensor, and performs brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.

Downhill Assist Control Target Vehicle Speed
Travel Direction Forward 5 km/h to 7 km/h (3 mph to 4 mph)
Backward 3 km/h to 5 km/h (2 mph to 3 mph)


iii.

During a downhill assist control operation, the skid control ECU outputs signals to the stop light control relay to cause the stop light to turn on, and to the combination meter to cause the slip indicator light to blink.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

Downhill Assist Control Operation
Item Downhill Assist Control Not Activated Downhill Assist Control Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder



j.

CRAWL

i.

Based on the information provided by various sensors, switches and the ECM, the skid control ECU determines the conditions that enable the CRAWL to operate. The skid control ECU computes the target vehicle speed (approximately 1 km/h to 6 km/h, 1 mph to 3.7 mph) to control the vehicle speed, and the target wheel speeds to control the wheel slipping. The target vehicle speed can be changed using the CRAWL speed selector.


ii.

When the vehicle speed differs from the target speed, the engine output is regulated. When the wheel speeds differ from the target speeds, the hydraulic brake pressure of the wheels is regulated.


iii.

The skid control ECU controls the fluid pressure that is generated by the brake booster pump assembly and applies it by way of the solenoid valves to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.

X102108E08
5.417,3.115 5.729,3 true 4.417,3.094 4.635,2.833 true 3.427,3.115 3.635,2.813 true 1.771,3.24 2.083,3.115 true 4.583,4.406 4.885,4.635 0.302,0.229 10 false *d 4.042,4.406 4.344,4.656 0.302,0.25 10 false *c 2.625,4.406 2.927,4.635 0.302,0.229 10 false *b 5.49,2.208 5.781,2.458 0.292,0.25 10 false *8 4.51,2.219 4.75,2.5 0.24,0.281 10 false *7 3.521,2.208 3.781,2.51 0.26,0.302 10 false *6 4.625,1.396 4.854,1.625 0.229,0.229 10 false *4 3.708,1.406 3.938,1.635 0.229,0.229 10 false *3 2.74,1.406 3.01,1.719 0.271,0.313 10 false *2 1.896,1.406 2.104,1.635 0.208,0.229 10 false *1 2.51,2.229 2.823,2.51 0.313,0.281 10 false *5 5.76,2.875 6.104,3.167 0.344,0.292 10 false *12 4.531,2.646 4.833,2.875 0.302,0.229 10 false *11 3.542,2.625 3.844,2.854 0.302,0.229 10 false *10 1.594,3.156 1.896,3.385 0.302,0.229 10 false *9 2.052,4.406 2.333,4.667 0.281,0.26 10 false *a

CRAWL Operation
Item CRAWL Not Activated CRAWL Activated
Increase Mode Holding Mode Reduction Mode
Switching Solenoid Valve *1 STR Off (Closed) On (Open) ← Off (Closed)
*2 SREC Off (Open) On (Closed) ← Off (Open)
*3 SREA Off (Closed) On (Open) ← ←
*4 SMCF Off (Open) On (Closed) ← ←
Control Solenoid Valve Front Brake LH *7 SFLH Off (Open) ← On (Closed) ←
*11 SFLR Off (Closed) ← ← On (Open)
*c Wheel Cylinder Pressure - Increases Holds Reduces
Front Brake RH *8 SFRH Off (Open) ← On (Closed) ←
*12 SFRR Off (Closed) ← ← On (Open)
*d Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake LH *5 SRLH Off (Open) ← On (Closed) ←
*9 SRLR Off (Closed) ← ← On (Open)
*a Wheel Cylinder Pressure - Increases Holds Reduces
Rear Brake RH *6 SRRH Off (Open) ← On (Closed) ←
*10 SRRR Off (Closed) ← ← On (Open)
*b Wheel Cylinder Pressure - Increases Holds Reduces
V100135

To Brake Master Cylinder Reservoir
V100136

From Brake Booster Accumulator Assembly
V100137

From Brake Master Cylinder




FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors or hydraulic brake booster assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning or indicator lights illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTC and check function, refer to the Repair Manual.