FUNCTION OF MAIN COMPONENTS
The main components of the EGR system are as follows:
| Component | Function |
| ECM | Controls the EGR system based on signals from each sensor. |
| Electric EGR Control Valve Assembly | Actuated by the ECM, this valve controls the flow rate of EGR gas. |
| EGR Valve Position Sensor (Built into Electric EGR Control Valve Assembly) | Detects the EGR valve position. |
| Diesel Throttle Valve | Actuated by the ECM, this valve controls the flow rate of intake air. |
| No. 1 EGR Cooler | Cools EGR gas. |
| No. 2 EGR Valve Assembly | Switches the flow passage of EGR gas in 2 stages. |
The main components of the catalyst support control are as follows:
| Component | Function |
| ECM | Controls the catalyst support control based on signals from each sensor. |
| Exhaust Gas Temperature Sensor | Detects the exhaust gas temperature. |
| No. 2 Exhaust Gas Temperature Sensor | |
| No. 3 Exhaust Gas Temperature Sensor | |
| Differential Pressure Sensor | ·
Monitors the differential pressure before and after the DPF. ·
Compares this data with the PM accumulation amount calculated by the ECM. If there is a large deviation in the comparison result, the ECM corrects the PM accumulation amount. |
| Exhaust Fuel Addition Injector Assembly | Injects fuel into the exhaust manifold. |
| Air Fuel Ratio Sensor | Detects the oxygen concentration in exhaust gas. |
The main components of the UREA SCR system are as follows*:
| Component | Function |
| ECM | Receives the signals from No. 4 Exhaust gas temperature sensor and NOx sensor (nitrogen oxides sensor) and sends the signals to UREA pump control ECU. |
| UREA Pump Control ECU | Controls the UREA SCR system based on signals from each sensor. |
| No. 4 Exhaust Gas Temperature Sensor | Detects the exhaust gas temperature. |
| Air Fuel Ratio Sensor | Detects the oxygen concentration in exhaust gas. |
| NOx Sensor (Nitrogen Oxides Sensor) | Detects the concentration of NOx in the exhaust gas. |
*: Models compliant with EURO 6 emission regulations
FUNCTION
EGR System
This system is designed to help reduce and control NOx formation due to a reduction of peak temperature in the engine combustion chamber, which is accomplished by the introduction of an amount of inert gas into the intake manifold.
Catalyst Support Control
When an extremely large amount of PM is accumulated in the DPF, the back pressure of the engine increases and the PM is combusted at once, potentially damaging the filter. In order to prevent that, it is necessary to forcibly combust the accumulated PM. Therefore, the accumulated PM is combusted by increasing the temperature of the filter.
If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message is displayed on the multi-information display*1 or the DPF warning light*2 illuminates or blinks to notify the driver.
*1: Models with multi-information display
*2: Models without multi-information display
UREA SCR System (Models Compliant with EURO 6 Emission Regulation)
Urea solution is injected by the urea injector set to purify NOx in the exhaust gas.
SYSTEM CONTROL
EGR System
The EGR system carries out the following controls:
The ECM actuates the electric EGR control valve assembly, which regulates the volume of EGR gas recirculation, in accordance with the engine condition.
The ECM switches the bypass passage of the No. 1 EGR cooler via the No. 2 EGR valve assembly in 2 stages in order to optimize the temperature of the EGR gas and clean exhaust gases.
Catalyst Support Control
In order to regenerate the DPF, the temperature of the DPF is increased to combust the accumulated PM in the DPF, expelling it as CO2 and H2O.
The ECM monitors the engine condition and calculates the total amount of accumulated PM. In addition, the ECM calculates the amount of combusted PM according to the engine speed, fuel injection volume and the injection volume of the exhaust fuel addition injector assembly. The amount of accumulated PM in the DPF is calculated based on the calculated total amount of accumulated PM and the amount of combusted PM. The ECM urges the driver to perform PM automatic or manual regeneration according to the level of accumulated PM.
When automatic or manual regeneration is performed, the injection of the exhaust fuel addition injector assembly and the engine combustion condition are controlled, increasing the temperature of the DPF. As a result, the temperature of the DPF becomes approximately 600°C to 700°C and PM is combusted.
When the vehicle is continuously driven with a high exhaust temperature such as at high speeds, the temperature of the DPF is sufficiently increased and PM is spontaneously combusted. At this time, no special control such as exhaust fuel addition injector assembly control, etc. is performed.
When the vehicle is continuously driven while the temperature of the DPF is not high enough for PM combustion such as when driving for a short distance or driving for a short time, catalyst performance is decreased. As a result, PM is accumulated in the DPF. When the amount of accumulated PM exceeds the threshold (for automatic regeneration), the ECM performs automatic regeneration until the amount of PM reaches zero.
If the vehicle continues to be driven for a short distance even after automatic regeneration is performed, more PM is accumulated. When the amount of accumulated PM exceeds the threshold (for manual regeneration), a message is displayed on the multi-information display*1 or the DPF warning light*2 illuminates or blinks to urge the driver to perform manual regeneration.
*1: Models with multi-information display
*2: Models without multi-information display
Automatic Regeneration
When automatic regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition, increasing the temperature of the DPF to combust the PM. Idle up is performed while the vehicle is stopped.
The end of automatic regeneration is calculated by the ECM according to the amount of accumulated PM.
Manual Regeneration
The following methods are used to perform manual regeneration. For details of manual regeneration operation, refer to the Repair Manual.
Driving Method
Drive for 20 to 30 minutes at 65 km/h or higher to perform manual regeneration.
Global TechStream (GTS) Operation Method
Stop the vehicle and operate the Global TechStream (GTS) to perform manual regeneration.
When manual regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition and performs idle up, increasing the temperature of the DPF to combust the PM.
The end of manual regeneration is calculated by the ECM according to the amount of accumulated PM.
Fail-safe
If manual regeneration is performed when the amount of accumulated PM is beyond the threshold, the DPF may get damaged. Therefore, when the amount of accumulated PM exceeds the threshold (for the fail-safe function), the injection volume is controlled to a minimum level to cancel regeneration control. As a result, manual regeneration cannot be performed properly. At the same time, the MIL illuminates and a message is displayed on the multi-information display*1 or the DPF warning*2 light blinks to notify the driver of a malfunction.
| Text in Illustration | MIL | DPF Warning Light*2 | Massage on Multi-information Display*1 |
|---|---|---|---|
| A | - | - | - |
| B | - | - | - |
| C | - | Illuminate | DPF FULL SEE OWNER'S MANUAL |
| D | - | Blink | DPF FULL VISIT YOUR DEALER |
| E | Illuminate | Blink | DPF FULL VISIT YOUR DEALER |
*1: Models with multi-information display
*2: Models without multi-information display
| *A | Models without Multi-information Display | *B | Models with Multi-information Display |
| *1 | MIL | *2 | DPF Warning Light |
| *3 | Multi-information Display | - | - |
UREA SCR System (Models Compliant with EURO 6 Emission Regulation)
A UREA SCR system is used to purify NOx in the exhaust gas. The urea SCR system injects urea solution into the exhaust gas to generate ammonia. The generated ammonia produces a chemical reaction with the NOx in the exhaust gas on the SCR catalyst, breaking it down into nitrogen and water, thereby purifying the exhaust gas.
The UREA SCR system is composed of a UREA pump control ECU, urea tank sub-assembly, urea injector set, urea pump, No.4 exhaust gas temperature sensor and NOx sensor (nitrogen oxides sensor).
In the UREA SCR system, the UREA pump control ECU controls the urea injector set and urea pump based on various signals.
The amount of NOx in the exhaust gas increases as the engine load increases. This system injects urea solution according to the engine load in order to maintain the amount of NOx at a certain level or less.
When the SCR catalyst temperature reaches a certain temperature or more, such as when high-load driving continues for a long period of time or DPF regeneration is in progress, the amount of urea solution that is injected is further increased.
The amount of urea solution that is consumed changes depending on the driving conditions and environment. During high-load driving, the amount of urea solution that is consumed increases and the driving range decreases. Inversely, during low-load driving, the amount of urea solution that is consumed decreases and the driving range increases.
CONSTRUCTION
Oxidation Catalyst
An oxidation catalyst is used to purify HC and CO in the exhaust gas.
| *1 | Exhaust Manifold Converter Sub-assembly | *2 | Oxidation Catalyst |
|
Exhaust Gas | - | - |
DPF
A DPF catalyst is used to collect and purify PM.
| *1 | Exhaust Manifold Converter Sub-assembly | *2 | DPF |
|
Exhaust Gas | - | - |
SCR Catalyst
2 SCR catalysts and an ammonia slip catalyst are provided in the front pipe area to improve NOx purification performance.
| *1 | SCR Catalyst | *2 | Ammonia Slip Catalyst |
|
Exhaust Gas | - | - |
UREA Pump
A urea pump is used, and is positioned in the bottom of the urea tank sub-assembly.
| *1 | Float Sensor | *2 | Urea Solution Temperature Sensor |
| *3 | Pressure Sensor | *4 | Filter |
| *5 | Pump Motor | *6 | Heater |
The urea pump has the following functions:
| Function | Outline |
|---|---|
| Pump Function | While performing feedback control according to the pressure sensor inside the urea pump, the pump raises the pressure to approximately 500 kPa, sending urea solution to the urea injector set. |
| Heating Function | The heater inside the urea pump is operated to thaw the urea solution so that exhaust gas can be purified even when the ambient temperature is low and the urea solution freezes. The heater turns on and off according to the urea solution temperature sensor inside the urea pump. |
| Filter Function | Foreign matter that enters the urea tank sub-assembly is collected by the filter inside the urea pump, preventing foreign matter from getting jammed in the urea pump and urea injector set. |
| Level Gauge Function | The fluid level position is detected by the float sensor inside the urea pump in order to detect the remaining quantity of urea solution inside the urea tank sub-assembly. |
EGR Valve
A DC motor type electric EGR control valve assembly is used. The placement of the electric EGR control valve assembly at the intersection between the intake passage and EGR bypass facilitates the uniform distribution of EGR gas and intake air.
An EGR valve position sensor is provided in the electric EGR control valve assembly. This sensor enables EGR valve control at a higher level of precision by detecting the opening angle of the EGR valve.
| *1 | Electric EGR Control Valve Assembly | - | - |
EGR Pipe and EGR Valve
A water-cooled type No. 1 EGR cooler is used between the exhaust manifold and electric EGR control valve assembly. In the water-cooled type No. 1 EGR cooler, engine coolant flows through eightlayered gas passage to cool down the EGR gas.
The No. 2 EGR valve assembly is used. The EGR gas passage is switched in 2 stages by the No. 2 EGR valve assembly to optimize the temperature of the EGR gas.
| *1 | Exhaust Manifold | *2 | No. 1 EGR Cooler |
| *3 | Diesel Throttle Body Assembly | *4 | Intake Manifold |
| *5 | No. 2 EGR Valve Assembly | *6 | Electric EGR Control Valve Assembly |
| *a | Intake Air | *b | EGR Gas |
| *c | EGR Gas (through Bypass Passage) | - | - |
Exhaust Fuel Addition Injector
The exhaust fuel addition injector assembly is installed on the exhaust manifold. Fuel is supplied by the injector to maintain the temperature of the catalyst, removing PM.
An exhaust fuel addition injector assembly consists of a needle valve body, a needle valve, and a solenoid valve.
| *1 | Solenoid Valve | *2 | Needle Valve |
| *3 | Needle Valve Body | - | - |
Differential Pressure Sensor
The differential pressure sensor measures the pressure differences between before and after the DPF with PM in order to detect clogging.
The sensor is mounted on the cylinder head. The DPF and the sensor are connected with pipes and hoses.
Exhaust Gas Temperature Sensor
An exhaust gas temperature sensor, which is a thermistor type, is installed before the oxidation catalyst, before the DPF, after the DPF and after the SCR catalyst*, in order to detect the temperature of the exhaust gas.
*: Models compliant with EURO 6 emission regulation
| *1 | Exhaust Gas Temperature Sensor | - | - |
Air Fuel Ratio Sensor
An air fuel ratio sensor is used to optimize the combustion and the catalyst conditions. The structure of the sensor is layered to promote early activation, achieving air fuel ratio feedback control in the early stages of engine start.
The air fuel ratio sensor is installed after the DPF catalyst.
| *1 | Air Fuel Ratio Sensor | - | - |
NOx Sensor
An NOx sensor (nitrogen oxides sensor) is installed in center exhaust pipe assembly, in order to detects the concentration of NOx in the exhaust gas.
| *1 | NOx Sensor (Nitrogen Oxides Sensor) | - | - |