Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2017.08–2020.08
NM27T0E _51 Engine / Hybrid System _053610 CRUISE CONTROL _0330904 LANE DEPARTURE ALERT SYSTEM CO CONTROL F

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  CONTROL  LANE DEPARTURE ALERT CONTROL  


FUNCTION OF MAIN COMPONENTS


Components Function

*: Models with camera heater

Forward Recognition Camera
·

Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Controls the lane departure alert system.

·

Sends the indicator illumination request signal, multi-information display indication light request signal, and meter buzzer sound request signal to the combination meter assembly.

·

Receives vehicle information and turn signal light operation signals.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly)* Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Driving Support ECU Assembly
·

Sends the LDA main switch signal to the forward recognition camera.


Millimeter Wave Radar Sensor Assembly Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Combination Meter Assembly Sends a turn signal command to the forward recognition camera.
Combination Meter Assembly LDA Indicator Illuminates or turns off in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Master Warning Light Illuminates to warn the driver in accordance with signals from the forward recognition camera.
Meter Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
ECM Sends the accelerator pedal opening angle signal to the forward recognition camera.
Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera and driving support ECU assembly.
Steering Pad Switch Assembly LDA Main Switch Detects the on/off status of the lane departure alert system and sends a signal to the driving support ECU assembly.
Meter Control Switch Changes the customization settings of the lane departure alert system.
Airbag ECU Assembly Detects the yaw rate and sends a signal to the forward recognition camera.
Steering Sensor Sends the turning angle of the steering wheel to the forward recognition camera and driving support ECU assembly.
Headlight Dimmer Switch Assembly Sends a turn signal command to the combination Meter assembly.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication buses.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.


OPERATION CONDITION


a.

Operating Conditions of Lane Departure Alert System (Lane Departure Alert Function)

Operation Condition
Operating The lane departure alert system (lane departure alert function) is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the lane departure alert system, the LDA indicator illuminates.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The lane departure alert system (lane departure alert function) is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers are detected.

·

Immediately after the lane departure alert is activated.

·

The vehicle crosses halfway or further over a lane marker.

·

Detection of the lane width other than regulated.

·

Detection of the curve radius other than regulated.

·

A malfunction is detected in the lane departure alert system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The lane departure alert system (lane departure alert function) is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The lane departure alert system is temporarily stopped.

·

The lane departure alert system is malfunctioning.

·

The ignition switch is turned off.


The lane departure alert system (lane departure alert function) resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The lane departure alert system condition returns to normal.

·

The ignition switch is turned off and on (IG) again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction.




b.

Operating Conditions of Lane Departure Alert System (Vehicle Sway Warning Function)

Operation Condition
Operating The lane departure alert system (vehicle sway warning function) is activated when all of the following conditions are met:
·

Sway warning available is selected via operation of the steering pad switch assembly.

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

A system malfunction is not detected.

·

No turn signal command is detected.


Suspended The lane departure alert system (vehicle sway warning function) is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

One side of lane markers is not detected.

·

A turn signal command is detected.

·

Immediately after the lane departure alert is activated.

·

Detection of the lane width other than regulated.

·

Detection of the curve radius other than regulated.

·

A malfunction is detected in the lane departure alert system.

·

The temperature of the forward recognition camera is abnormal.


Canceled/Resume The lane departure alert system (vehicle sway warning function) is stopped when any one of the following conditions is met:
·

The lane departure alert system is malfunctioning.

·

The ignition switch is turned off.

·

Sway warning unavailable is selected via operation of the steering pad switch assembly.


The lane departure alert system (vehicle sway warning function) resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The lane departure alert system condition returns to normal.

·

The ignition switch is turned off and on (IG) again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction.

·

Sway warning available is selected via operation of the steering pad switch assembly.





SYSTEM CONTROL


a.

Lane Departure Alert System Warning Operation

i.

Function Overview (Lane Departure Alert Function)

·

If the lane departure alert system judges that the vehicle may deviate from the lane it is in, the lane departure alert system illuminates the indicator in the combination meter display and sounds a meter buzzer so that the driver can take action to avoid lane departure.

Y212241E02
4.406,0.135 4.958,0.448 0.552,0.313 10 false Warning 3.917,1.063 4.375,1.385 0.458,0.323 10 false Buzzer 5,1.063 5.5,1.333 0.5,0.271 10 false Display 0.083,2.406 3.063,2.74 2.979,0.333 10 false This illustration is only for explanatory purposes.



ii.

Function Overview (Vehicle Sway Warning Function)

·

The lane departure alert system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver before a lane departure or collision occurs.

Y180903E08
4.917,1.531 5.521,1.833 0.604,0.302 10 false Warning 4.396,2.021 4.906,2.354 0.51,0.333 10 false Buzzer 0.094,2.375 3.135,2.76 3.042,0.385 10 false This illustration is only for explanatory purposes. 5.448,2.052 5.948,2.375 0.5,0.323 10 false Display

·

The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:

Y215384E02
1.854,0.625 5.521,0.823 3.667,0.198 10 false Timing of lane departure 1.281,1.604 4.948,1.802 3.667,0.198 10 false The vehicle repeatedly deviates from its lane. 1.156,2.604 4.115,3.208 2.958,0.604 10 false The vehicle drifts within its lane when the driver is inattentive 1.333,3.969 3.927,4.49 2.594,0.521 10 false The steering wheel is turned abruptly when the driver is inattentive. 4.823,3.417 6,4.198 1.177,0.781 10 false Would You Like to Take a Break? 4.708,1.823 6.156,2.156 1.448,0.333 10 false Please Take a Break 2.302,6.042 4.146,6.677 1.844,0.635 10 false Attention Level (Vehicle Sway Warning Function On) 0.563,6.063 4.229,6.26 3.667,0.198 10 false High 6.115,5.917 7,6.896 0.885,0.979 10 false Vehicle Sway Warning Function Off 5.469,6.083 5.844,6.479 0.375,0.396 10 false Low 0.281,7.385 3.948,7.583 3.667,0.198 10 false These illustrations are examples.





FUNCTION


a.

Using the meter control switches of the steering pad switch assembly, the lane departure alert system settings functions and the vehicle sway warning functions can be customized.

Y218726C01
4.594,1.813 5.813,1.063 true 4.406,2.292 5.469,3.052 true 5.854,0.938 6.167,1.094 0.313,0.156 10 false *a 5.5,3.042 5.813,3.198 0.313,0.156 10 false *b
*a Meter Control Switch *b LDA Main Switch



b.

Lane Departure Alert System Settings Functions Customization

Item (Select using the up/down button of the meter control switch) Description Setting (Change using the center button of the meter control switch)
Sensitivity Timing of the lane departure alert
·

High

·

Standard


Sway Warning Select to enable/disable the vehicle sway warning function
·

On

·

Off


Sway Sensitivity Timing of the vehicle sway warning function
·

High

·

Standard

·

Low





DIAGNOSIS


a.

If a malfunction is detected in the lane departure alert system, the forward recognition camera cancels the lane departure alert system, does not illuminate the LDA indicator and illuminates the master warning light, sounds the meter buzzer, and displays a message on the multi-information display to inform the driver of the malfunction.


b.

At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC). When the Global TechStream (GTS) is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.