Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2017.08–2020.08
NM27T0E _51 Engine / Hybrid System _053610 CRUISE CONTROL _0330905 ROAD SIGN ASSIST SYSTEM CO CONTROL F

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  CONTROL  ROAD SIGN ASSIST CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the RSA have the following functions.

Components Function

*1: Models with camera heater

*2: The threshold can be adjusted to 1 of 3 levels through the customization function.

Forward Recognition Camera Monocular Camera Sensor Captures road signs.
Forward Recognition Camera ECU
·

Performs RSA system control based on information of road signs captured by the monocular camera.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.*1


Camera Heater (Forward Recognition Hood)*1 Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Detects object information and sends a signal to the forward recognition camera.
ECM Transmits the shift position signal to the forward recognition camera.
Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera.
Steering Pad Switch Assembly Meter Control Switch Sends a multi-information operating signal to the forward recognition camera.
Combination Meter Assembly Outputs turn light signal commands, which are sent from the headlight dimmer switch assembly, to the forward recognition camera.
Combination Meter Assembly Multi Buzzer Sounds when the speed limit is exceeded or no overtaking notifications are issued.*2
Multi-information Display
·

Displays road signs recognized by the forward recognition camera.

·

The RSA system can be turned on and off through the settings tab.


Airbag Sensor Assembly Yawrate Sensor Detects the yaw rate and sends it to the forward recognition camera.
Speed Sensors Detect the wheel speed of each of the 4 wheels and send it to the skid control ECU.
Air Conditioning Amplifier Assembly Sends the outside air temperature to the forward recognition camera.
Central Gateway ECU Relays the data between the each CAN bus.



FUNCTION


a.

The RSA system recognizes the following traffic signals using the forward recognition camera.

Category Sign Type Example of Recognizable Sign

*: A speed limit sign with a value greater than 130 can not be recognized by the system and can result in a wrong speed limit being displayed.

Speed Limit Round maximum speed limit/End of speed limit*
Y180848

No Overtaking No overtaking/End of no overtaking
Y180849

Supplemental Signs Road condition signs Ramp Way
Y180850

Rain
Y180851

Wet
Y189642

Ice
Y180852

End of Prohibition
Y180854



b.

The RSA system recognizes the following traffic signals using the forward recognition camera.

Category Display Example Details
Speed Limit Related Speed Limit
Y180855

·

Informs the driver of the maximum speed limit of the currently driven road.

·

The displayed sign reflects the speed limit on the recognized sign.


No Overtaking Related
Y180856

Informs the driver when they are in a no overtaking zone on the currently driven road.
All Canceled (All restrictions canceled. Return to default road regulations.)
Y180854

Informs the driver when all applicable prohibitions, such as speed limit and no overtaking, have ended.
Speed Limit with Supplemental Sign Related Ramp Way
Y180858

Informs the driver of the ramp way direction. However, this item is not displayed when making a lane change without operating the turn signal light.
Rain
Y194214

Informs the driver of the maximum speed limit on the currently driven road when it is raining or the road surface is wet.
Ice
Y188514

Informs the driver of the maximum speed limit on the currently driven road when there is accumulated snow or ice.
Blank
Y188515

The display is blank when the system is unable to recognize a supplemental sign.

HINT:

A non-official (sign not meeting vienna convention) or a recently introduced traffic sign may not be recognized.



c.

Notification functions are used in the RSA system which invert the colors of displayed signs, flash signs, etc. to notify the driver.

i.

Speed Limit Exceeded Notification

·

While a speed limit sign is displayed, if the actual vehicle speed exceeds the speed limit plus a designated threshold*, the colors of the displayed sign are inverted. For example, if the threshold is set to 5 km/h and the speed limit sign is 60 km/h, the colors of the displayed sign are inverted when the actual vehicle speed exceeds 65 km/h. Furthermore, the system also inverts a speed limit sign with supplemental sign in the same way. However, the system does not invert the colors of the supplemental sign.

*: The threshold can be adjusted to 1 of 3 levels through the customization function.


·

The multi buzzer may be set to sound during notifications through the customization function. However, if a speed limit recognized from a speed limit with supplemental sign is exceeded, the multi buzzer does not sound.

HINT:

Traffic environment (driving side, speed unit) is judged incorrectly by the system.



Notification Method Display Example
Inverted Display
Y180861



ii.

No Overtaking Notification

·

While a no overtaking sign is displayed, if the system detects that the vehicle is attempting to overtake another vehicle, the system flashes the displayed sign.

·

The multi buzzer may be set to sound during notifications through the customization function.


Notification Method Display Example
Flashing Display
Y180862




d.

The RSA can be turned on or off through the settings tab of the multi-information display.


e.

A customization function is used for the RSA, which allows settings such as the notification method and level for exceeding the speed limit to be changed. Setting changes are made through the customization tab of the multi-information display. Refer to the Repair Manual for details.



SYSTEM CONTROL


a.

RSA Control Pattern 1

i.

After a road sign is recognized by the forward recognition camera and the vehicle passes by, the sign is displayed on the multi-information display.


ii.

While a sign is displayed on the multi-information display or main display, if a new road sign is not recognized within a specified distance, display of the current sign is turned off.

Y212198E01
2.667,1.479 2.25,0.76 2.25,0.76 1.948,0.76 true 0.51,0.667 2,1.01 1.49,0.344 10 false Road Sign Recognized 3.865,0.688 5.51,1.021 1.646,0.333 10 false Specified Distance Driven 1.021,2.646 2.177,2.99 1.156,0.344 10 false : Sign display off 1.042,3.177 2.198,3.521 1.156,0.344 10 false : Sign display on



b.

RSA Control Pattern 2

i.

When the ignition switch is turned off while a sign is displayed on the multi-information display, the same sign is displayed when the ignition switch is turned ON again.

Y212199E01
2.521,0.375 3.542,1.031 1.021,0.656 10 false Power Switch is Turned Off 5.521,0.354 6.563,0.781 1.042,0.427 10 false Power Switch is Turned On (IG) 1.177,2.979 2.313,3.354 1.135,0.375 10 false : Sign display on



c.

RSA Control Pattern 3

i.

While a sign is displayed on the multi-information display, the sign is turned off when turning left or right onto a new road.

HINT:

The driving behavior (turning, lane change etc.) is judged incorrectly by the system.


Y212200E01
0.885,4.292 2.021,4.646 1.135,0.354 10 false : Sign display off 0.885,5.01 2.021,5.365 1.135,0.354 10 false : Sign display on 5.802,3.844 6.594,4.302 0.792,0.458 10 false Road Sign Recognized




DIAGNOSIS


a.

If a malfunction is detected in the RSA system, the forward recognition camera cancels the RSA system, sounds the multi buzzer in the combination meter assembly, and displays a message on the multi-information display to inform the driver of the malfunction.


b.

At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC). For details, refer to the Repair Manual.