Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2020.08
NM27T0E _52 Drivetrain _053612 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260143 AUTOMATIC TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS



Component Function
Torque Converter Assembly
·

Transmits the engine power to the transmission.

·

Increases engine torque.


Oil Pump Provides oil pressure necessary for transmission operation.
No. 1 Clutch (C1) Connects the input shaft and the intermediate shaft.
No. 2 Clutch (C2) Connects the input shaft and the center planetary gear assembly.
No. 1 Brake (B1) Locks the rotations of the front planetary carrier and the center planetary ring gear.
No. 2 Brake (B2) Locks the rotation of the rear planetary ring gear.
No. 4 Brake (B4) Locks the rotation of the front planetary ring gear.
1-way Clutch (F) Locks the counterclockwise rotations of the center planetary carrier and the rear planetary ring gear.
Planetary Gears Change the power transmission route in accordance with clutch and brake operation, and increase or decrease output shaft revolution accordingly.
Solenoid Valve (SL1) Performs shift controls.
Solenoid Valve (SL2) Performs shift controls.
Solenoid Valve (SL3) Performs shift controls.
Solenoid Valve (SL4) Performs shift controls.
Solenoid Valve (SLT) Controls line pressure.
Solenoid Valve (SLU)
·

Performs lock-up clutch controls.

·

Performs B2 brake hydraulic pressure controls (only for the 1st range when the S mode is selected).


Solenoid Valve (SL) Shifts between lock-up hydraulic pressure and B2 brake hydraulic pressure.
No. 1 ATF Temperature Sensor Detects the ATF temperature.
No. 2 ATF Temperature Sensor Detects the ATF temperature.
Transmission Revolution Sensor (NT) Detects the input speed of the transmission.
Transmission Revolution Sensor (SP2) Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly Detects the shift lever position (P, R, N, D).
Transmission Control Switch
·

Detects that the shift lever is in S.

·

Detects the driver's shift-up and shift-down operations when the shift lever is in S.


Shift Paddle Switch (Transmission Shift Switch Assembly)*1 Detects the shift-up and shift-down operations performed by the driver.
2nd Start Switch (Pattern Select Switch Assembly) Sends a 2nd start mode signal to the ECM.
Drive Mode Select*2
·

Outputs the NORMAL, SPORT*3 or SPORT S/S+*4 mode signal to the ECM when operated by the driver.

·

Outputs the ECO mode signal to the ECM via the air conditioning amplifier assembly when operated by the driver.


Combination Meter Assembly Shift Display
·

Indicates the shift lever position.

·

Indicates to inform the driver of driving in D mode or S mode.

·

Indicates the shift range (S1 to S6).


MIL Illuminates or blinks to inform the driver when the ECM detects a malfunction.
2nd Start Indicator Light Illuminates when the driver selects the 2nd start mode.
ATF Temperature Warning Light*5 Warns the driver by lighting up when the ATF is at a high temperature.
Multi-information Display*6
·

Warns the driver by displaying a message when the ATF is at a high temperature.

·

Displays a Diagnostic Trouble Code (DTC).


Master Warning Light*6 Warns the driver by lighting up when a message is shown on the multi-information display.
Buzzer
·

Sounds when shift-down operation is rejected in S mode.

·

Warns the driver by sounding when a message is shown on the multi-information display.*6


ECM
·

Controls each solenoid valve and engine output in response to signals from each sensor and switch.

·

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.


4WD Control ECU Sends a drive mode signal to the ECM.
Air Conditioning Amplifier Assembly Sends a shift-up tardiness control signal to the ECM.
Oil Pump with Solenoid Assembly*7 Holds the AT oil pressure during idle stop.

HINT:

*1: Models with shift paddle switch (transmission shift switch assembly)

*2: Models with drive mode select

*3: Models without AVS

*4: Models with AVS

*5: Models with analog display type combination meter assembly

*6: Models with Optitron display type combination meter assembly

*7: Models with stop and start system


SYSTEM CONTROL


Electronic Control of Automatic Transmission
Control Function
Powertrain Cooperative Control Controls both the shift control and engine output control in an integrated way, thus achieving excellent shift characteristics and driveability.
Shift Timing Control The ECM sends current to solenoid valves (SL1), (SL2), (SL3), (SL4) and/or (SL) based on signals from various sensors in order to shift the gears.
Line Pressure Control Actuates the solenoid valve (SLT) to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission.
Clutch Pressure Optimal Control The solenoid valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU) minutely control the clutch pressure in accordance with the engine output and driving conditions of the transmission.
Clutch to Clutch Pressure Control By utilizing pressure output from solenoid valves (SL1), (SL2), (SL3) and (SL4) based on drive signals sent from the ECM, each of the clutch and brake hydraulic pressures can be controlled directly and independently.
Vehicle Lift Control The clutch release speed has been optimized to restrain the upward movement of the vehicle when the shift lever is moved from D to N.
Shift Down Control The hydraulic passages and control have been optimized in order to ensure a smooth shift feel during downshifting to accelerate the vehicle.
Engine Torque Control Retards the engine ignition timing*1 or fuel injection volume*2 temporarily to improve shift feeling while upshifts or downshifts occur.
Lock-up Timing Control The ECM sends current to the solenoid valve (SLU) based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control Controls the solenoid valve (SLU), provides an intermediate mode for when the lockup clutch is between on and off, and increases the operating range of the lock-up clutch to improve fuel economy.
Coast Downshift Control The ECM performs downshifts before fuel cut ends to prevent the engine speed from decreasing and maintain the fuel cut.
Artificial Intelligence-shift Control (AI-shift Control) Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, which improves driveability.
Multi-mode Automatic Transmission The ECM appropriately controls the automatic transmission in accordance with the shift range position selected while the shift lever is in S.
D-range Paddle Active Control*3 When the shift lever is in D, the driver can select a desired shift range using the shift paddle switch (transmission shift switch assembly).
Drive Mode Select*4 Makes it possible to select the driving mode by performing switch operations.
ATF High Temperature Control When the ATF is at a high temperature, normal shifting characteristics will be changed to shifting characteristics which actively utilize the low gear range to prevent the oil temperature from rising further.

HINT:

*1: Models with 2TR-FE or 1GR-FE engine

*2: Models with 1GD-FTV engine

*3: Models with shift paddle switch (transmission shift switch assembly)

*4: Models with drive mode select


a.

Powertrain Cooperative Control

i.

The Driving Response and Acceleration Management System (DRAMS) is used for this model. This system integrally controls the engine, transmission and other driving related controls in order to improve vehicle maneuverability and driving comfort, as well as provide optimal drive feeling as a whole, including the behavior of the vehicle, while taking into account the drivers' needs and environment.


ii.

By integrally controlling the engine and automatic transmission using this system, acceleration maneuvers are replaced with drive force demanded by the driver. As a result, quick response and a high quality driving experience in accordance with the driver's intentions is achieved, such as when accelerating or decelerating, starting or stopping, or during gear shifts to provide demanded drive force while still producing a smoother shift transition.

X127069E04
1.104,1.313 1.75,1.698 0.646,0.385 10 false Engine 2.906,1.698 3.792,2.698 0.885,1 10 false Automatic Transmission 5.24,0.76 5.625,1.583 0.385,0.823 10 false Drive Force 6.344,1.51 6.833,1.917 0.49,0.406 10 false Time 5.396,2.333 6.948,2.75 1.552,0.417 10 false Generated Drive Force 3.24,3.156 4.49,3.521 1.25,0.365 10 false Engine Control 4.802,3.156 6.24,3.531 1.438,0.375 10 false Transmission Control 1.365,3.823 1.74,4.583 0.375,0.76 10 false Drive Force 2.198,4.438 2.615,4.865 0.417,0.427 10 false Time 1.115,4.896 2.396,5.667 1.281,0.771 10 false Converted into Drive Force Value 2.927,3.958 4.521,4.708 1.594,0.75 10 false Determination of Necessary Engine Torque 4.885,3.958 6,4.708 1.115,0.75 10 false Determination of Appropriate Gear 3.281,5.156 5.896,5.427 2.615,0.271 10 false Determination of Necessary Drive Force 4.49,5.583 6.073,5.948 1.583,0.365 10 false Powertrain Management 0.24,6.104 1.354,6.917 1.115,0.813 10 false Accelerator Pedal Operation 3.438,5.906 3.938,6.313 0.5,0.406 10 false ECM 5.073,6.146 6.656,6.51 1.583,0.365 10 false Skid Control ECU 4.948,6.5 6.531,6.865 1.583,0.365 10 false Brake Control System 0.625,6.917 2.208,7.281 1.583,0.365 10 false : Drive force 0.625,7.344 2.417,7.667 1.792,0.323 10 false : Drive force control signal 2.875,7.344 4.833,7.646 1.958,0.302 10 false : Cooperative control signal


iii.

Start Control (Models with 2TR-FE or 1GR-FE Engine)

·

With DRAMS, engine torque will optimally be controlled in a real-time manner in accordance with speed ratios between engine speed and turbine speed so that finely controlled starting capability has been provided while balancing the "reduction of a feel of jump and suppression of tire slipping" and "smooth responsiveness" when starting.



iv.

Integrated Drive Force Control (Models with 2TR-FE Engine)

·

By increasing drive force before making a downshift when accelerating, a feel of slowness after downshifting has been reduced, making it possible to balance smooth shift characteristic and responsiveness when accelerating.




b.

Line Pressure Control

i.

In order to obtain predetermined line pressure characteristics in accordance with each sensor signal, the ECM activates the solenoid valve (SLT) to regulate the throttle pressure.


ii.

This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.

X127070E17
0.594,0.594 2.583,0.792 1.99,0.198 10 false Line Pressure 0.802,2.313 1.198,2.781 0.396,0.469 10 false Oil Pump 1.448,1.5 2.073,2.135 0.625,0.635 10 false Primary Regulator Valve 3.302,2.042 4.229,2.563 0.927,0.521 10 false Solenoid Valve (SLT) 4.698,2.635 5.625,3.156 0.927,0.521 10 false ECM 5.625,0.5 6.927,0.833 1.302,0.333 10 false Input Speed Signal 5.625,0.917 6.927,1.25 1.302,0.333 10 false ATF Temperature 5.625,1.302 6.927,1.635 1.302,0.333 10 false Shift Position 5.625,1.708 6.927,2.042 1.302,0.333 10 false Gear Position 5.625,2.104 6.74,2.573 1.115,0.469 10 false Accelerator Pedal Opening Angle 5.625,2.896 6.594,3.385 0.969,0.49 10 false Engine Coolant Temperature 5.635,3.688 6.677,4.01 1.042,0.323 10 false Engine Speed 5.604,4.104 6.719,4.521 1.115,0.417 10 false Throttle Position* 5.635,4.875 6.823,5.292 1.188,0.417 10 false Intake Air Volume* 3.469,4.844 4.396,5.365 0.927,0.521 10 false Current 2.063,3.708 2.625,4.302 0.563,0.594 10 false Fluid Pressure 0.104,5.406 3.521,5.771 3.417,0.365 10 false *: Models with 1GR-FE or 2TR-FE engine



c.

Clutch Pressure Optimal Control

i.

The ECM monitors the signals from various types of sensors, such as the transmission revolution sensor (NT), allowing solenoid valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU) to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are achieved.

X127071E05
3.104,3.083 2.667,2.365 2.667,2.365 2.479,2.365 true 4.083,3.104 4.385,2.313 4.385,2.313 4.635,2.313 true 3.542,3.917 3.073,4.781 3.073,4.781 2.885,4.781 true 3.75,3.865 3.219,5.427 3.219,5.427 3.031,5.427 true 3.896,3.865 3.479,5.875 3.479,5.875 3.292,5.875 true 0.26,0.385 0.615,1.646 0.354,1.26 10 false Input Shaft rpm 1.438,0.25 2.323,1.094 0.885,0.844 10 false Target rpm Change Ratio 0.74,1.302 2.51,1.667 1.771,0.365 10 false Practical rpm Change Ratio 1.688,1.698 2.198,2.021 0.51,0.323 10 false Time 5.573,1.229 6.021,1.656 0.448,0.427 10 false ECM 0.167,2.26 2.427,2.625 2.26,0.365 10 false Transmission Revolution Sensor (NT) 4.677,2.219 7.115,2.594 2.438,0.375 10 false Transmission Revolution Sensor (SP2) 5.146,2.865 5.594,4.167 0.448,1.302 10 false Output Shaft Torque 6.604,3.823 7,4.219 0.396,0.396 10 false Time 0.938,4.667 2.885,5.302 1.948,0.635 10 false Solenoid Valve (SL1, SL2, SL3, SL4, SLT, SLU) 1.385,5.313 3.115,5.719 1.729,0.406 10 false No. 1 Temperature Sensor 1.646,5.771 3.375,6.229 1.729,0.458 10 false No. 2 Temperature Sensor 4.802,4.698 5.604,5.583 0.802,0.885 10 false Clutch/Brake Pressure 5.625,5.677 7.01,6.073 1.385,0.396 10 false Solenoid Drive Signal



d.

Clutch to Clutch Pressure Control

i.

By using a clutch to clutch pressure control without using 1-way clutches in the 2nd or higher gears, a light, compact 6-speed automatic transmission has been provided.


ii.

By utilizing pressure output from solenoid valves (SL1), (SL2), (SL3) and (SL4) based on drive signals sent from the ECM, each of the clutch and brake hydraulic pressures can be controlled directly and independently.

X150069E02
0.458,0.885 1.698,1.302 1.24,0.417 10 false Clutch Control Valve 0.458,2.219 1.698,2.635 1.24,0.417 10 false Clutch Control Valve 0.448,3.542 1.708,3.938 1.26,0.396 10 false Brake Control Valve 0.458,4.865 1.698,5.271 1.24,0.406 10 false Brake Control Valve 0.115,5.323 1.167,5.542 1.052,0.219 10 false Line Pressure 2.927,0.573 3.667,1.094 0.74,0.521 10 false Solenoid Valve (SL1) 2.927,1.896 3.667,2.417 0.74,0.521 10 false Solenoid Valve (SL2) 2.927,3.229 3.667,3.75 0.74,0.521 10 false Solenoid Valve (SL3) 2.927,4.542 3.656,5.052 0.729,0.51 10 false Solenoid Valve (SL4) 3.823,2.49 4.563,3.01 0.74,0.521 10 false ECM 4.656,0.438 7.104,0.708 2.448,0.271 10 false Transmission Revolution Sensor (NT) 4.656,1 7.104,1.271 2.448,0.271 10 false Transmission Revolution Sensor (SP2) 4.656,1.573 7.104,1.844 2.448,0.271 10 false No. 1 ATF Temperature Sensor 4.656,2.125 7.104,2.396 2.448,0.271 10 false No. 2 ATF Temperature Sensor 4.656,2.698 7.156,2.958 2.5,0.26 10 false Mass Air Flow Meter 4.656,3.448 6.969,3.76 2.313,0.313 10 false Engine Coolant Temperature Sensor 4.656,4.021 6.969,4.333 2.313,0.313 10 false Accelerator Pedal Position Sensor 4.656,4.594 6.969,4.906 2.313,0.313 10 false Throttle Position Sensor* 4.375,5.406 7.083,5.792 2.708,0.385 10 false *: Models with 2TR-FE or 1GR-FE engine



e.

Lock-up Timing Control

i.

The ECM operates the lock-up timing control in order to improve fuel economy.

Lock-up Timing Control Operation
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th ○ ○ ○
5th ○ ○ -
6th ○ - -

HINT:

○: Available

X: Does not operate

-: Not applicable




f.

Flex Lock-up Clutch Control

i.

During acceleration, partial control of the power transmission between the lock-up clutch and torque converter greatly boosts transmission efficiency in accordance with the driving conditions, improving fuel economy.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), flex lock-up clutch control operates. As a result, the fuel cut area is expanded and fuel economy is improved.


iii.

By allowing flex lock-up clutch control to continue operating during gearshifts, smooth torque transmission is obtained. As a result, fuel economy and driveability are improved.


iv.

For flex lock-up clutch control, H infinity (H∞) control theory is used to achieve a high level of system stability and response to various characteristic changes.

X127073E22
2.188,1.396 2,0.948 2,0.948 1.792,0.948 true 3.802,4.396 3.448,2.583 3.448,2.583 2.844,2.583 true 2.563,3.813 2.292,3.052 2.292,3.052 2.083,3.052 true 1.854,4.208 1.323,3.5 1.323,3.5 1.115,3.5 true 1.885,4.708 1.594,5.198 1.594,5.198 1.385,5.198 true 3.906,5.26 3.635,5.604 3.635,5.604 3.427,5.604 true 4.25,5.229 4.052,6.063 4.052,6.063 3.802,6.063 true 4.448,5.208 4.813,6.125 4.813,6.125 5.083,6.125 true 4.552,5.208 4.844,5.781 4.844,5.781 5.104,5.781 true 6.125,1.354 6.229,0.958 6.229,0.958 6.021,0.958 false 6.281,1.667 6.135,1.667 6.135,1.667 5.969,1.531 false 3.406,0.25 3.865,0.448 0.458,0.198 10 false ECM 0.625,0.865 1.719,1.438 1.094,0.573 10 false Accelerator Pedal Position Sensor*1 0.521,2.5 2.813,2.802 2.292,0.302 10 false Transmission Revolution Sensor (NT) 0.385,2.979 2.031,3.26 1.646,0.281 10 false Throttle Position Sensor*2 0.146,3.417 1.073,4.063 0.927,0.646 10 false Engine Coolant Temperature Sensor 0.427,5.104 1.354,5.76 0.927,0.656 10 false Crank Position Sensor 2.01,5.51 3.396,5.813 1.385,0.302 10 false Lock-up Control Valve 2.427,5.99 3.75,6.281 1.323,0.292 10 false Solenoid Valve (SLU) 5.177,6.042 7.156,6.302 1.979,0.26 10 false No. 1 ATF Temperature Sensor 5.188,5.688 7.135,5.969 1.948,0.281 10 false No. 2 ATF Temperature Sensor 0.115,6.344 2.302,6.708 2.188,0.365 10 false *1: Models with 1GD-FTV engine 2.385,6.354 5.375,6.75 2.99,0.396 10 false *2: Models with 2TR-FE or 1GR-FE engine 4.688,0.865 5.979,1.24 1.292,0.375 10 false Engine Speed Signal 4.729,1.229 5.177,1.76 0.448,0.531 10 false Engine Speed 5.292,1.906 6.208,2.219 0.917,0.313 10 false Vehicle Speed 6.323,1.573 6.75,2.24 0.427,0.667 10 false Input Speed Signal 6.219,2.896 6.771,3.771 0.552,0.875 10 false Linear Solenoid Signal 4.698,3.042 5.292,3.531 0.594,0.49 10 false Current 5.552,3.521 6.469,3.833 0.917,0.313 10 false Time

X102147E32
2.615,1.083 5.635,1.427 3.021,0.344 10 false : Lock-up operating range 0.271,0.125 3.292,0.469 3.021,0.344 10 false Flex Lock-up Operating Range 2.615,1.448 5.635,1.792 3.021,0.344 10 false : Flex lock-up operating range (acceleration) 2.615,1.813 5.635,2.156 3.021,0.344 10 false : Flex lock-up operating range (deceleration) 3.24,4.229 4.167,4.573 0.927,0.344 10 false Vehicle Speed 1.604,2.135 2,2.479 0.396,0.344 10 false Large 4.917,4.198 5.24,4.542 0.323,0.344 10 false High 0.813,3.01 1.99,3.688 1.177,0.677 10 false Accelerator Pedal Depressing Angle 0.583,4.083 1.729,4.75 1.146,0.667 10 false Accelerator Pedal is Released

Flex Lock-up Clutch Control Operation (Acceleration)
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th ○ ○ ○
5th ○ ○ -
6th ○ - -

HINT:

○: Operates

X: Does not operate

-: Not applicable


Flex Lock-up Clutch Control Operation (Deceleration)
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th ○ ○ X
5th ○ ○ -
6th ○ - -

HINT:

○: Operates

X: Does not operate

-: Not applicable




g.

Coast Downshift Control

i.

Downshift control is used when decelerating, allowing for low fuel consumption by extending fuel cut control as much as possible.


ii.

By performing flex lock-up control and downshift control at the same time when decelerating, a decrease of engine speed has been suppressed, while extending fuel cut control as much as possible without lowering the engine speed below the fuel cut recovery speed.


iii.

By expanding operating gears and widening operating areas through close-gear ratios, fuel efficiency has significantly been enhanced and drivability has been improved by optimizing deceleration force when controls are activated.

X127076E03
1.958,1.49 2.073,1.49 2.073,1.49 2.208,1.771 false 2.917,1.552 3.031,1.552 3.031,1.552 3.167,1.833 false 4.167,1.677 4.042,1.677 4.042,1.677 3.917,1.969 false 4.719,2.698 4.594,2.698 4.594,2.698 4.469,2.448 false 3.979,2.688 4.094,2.688 4.094,2.688 4.167,2.396 false 3.469,2.563 3.583,2.563 3.583,2.563 3.792,2.354 false 0.448,0.594 1.375,1.031 0.927,0.438 10 false Engine Speed 0.438,2 1.302,2.688 0.865,0.688 10 false Fuel Cut Return Speed 0.448,2.917 1.104,3.802 0.656,0.885 10 false Fuel Cut Duration 2.25,0.729 3.719,1.438 1.469,0.708 10 false Coast Downshifts Occur Earlier 1.542,1.375 2.021,1.688 0.479,0.313 10 false To 6th 2.469,1.448 2.938,1.823 0.469,0.375 10 false To 5th 4.229,1.583 4.813,1.906 0.583,0.323 10 false To 4th 4.99,2.99 5.5,3.323 0.51,0.333 10 false Time 3.146,3.427 4.24,3.802 1.094,0.375 10 false Extended Time 4.854,3.385 6.615,4.458 1.76,1.073 10 false Enhanced Fuel Efficiency Through Extended Fuel Cut Control 4.844,0.167 6.938,0.51 2.094,0.344 10 false : With coast downshift control 4.844,0.573 6.958,0.948 2.115,0.375 10 false : Without coast downshift control 4.76,2.594 5.344,2.927 0.583,0.333 10 false To 4th 3.563,2.573 4.031,2.948 0.469,0.375 10 false To 5th 3.042,2.458 3.51,2.854 0.469,0.396 10 false To 6th



h.

Artificial Intelligence-shift Control (AI-shift Control)

i.

AI-shift control selects optimal controls in accordance with "driving environment" and the "driver's intention" based on the degree of accelerator opening, vehicle speed, brake signals, etc.


ii.

Smooth driving and low fuel consumption have been achieved while driving normally. A strong and linear feeling of acceleration has been provided when accelerating. A direct feeling of deceleration through engine braking and high fuel efficiency have been achieved when decelerating.

X127077E04
2.26,0.083 5.01,0.802 2.75,0.719 10 false Selects Optimal Controls in accordance with "Driving Environment" and "Driver's Intention" 2.802,0.885 4.51,1.292 1.708,0.406 10 false Control when Accelerating 2.896,2.052 4.479,2.417 1.583,0.365 10 false Automatic Shift Control 2.917,3.271 4.521,3.688 1.604,0.417 10 false Uphill/Downhill Control 2.375,1.406 4.896,1.719 2.521,0.313 10 true Direct and Linear Feeling of Acceleration 2.396,2.552 4.948,2.906 2.552,0.354 10 true Smooth Drive and Low Fuel Consumption 2.469,4.219 5.271,4.625 2.802,0.406 10 false - Securing Engine Braking Going Downhill 2.469,3.885 5.031,4.229 2.563,0.344 10 false - Maintaining Drive Force Going Uphill


iii.

Under road condition support control, the ECM identifies the throttle valve opening angle, accelerator pedal opening angle and vehicle speed to determine whether the vehicle is being driven uphill or downhill. Unnecessary upshifting is restrained to automatically achieve optimal drive force at all times while driving uphill. Downshifting is automatically conducted to achieve optimal engine brake force while driving downhill.

X127078E03
0.635,2.823 1.031,3.146 0.396,0.323 10 false 6th 0.635,3.323 0.948,3.604 0.313,0.281 10 false 6th 1.26,2.823 1.542,3.146 0.281,0.323 10 false 4th 1.677,2.823 2.01,3.115 0.333,0.292 10 false 5th 2,2.823 2.344,3.167 0.344,0.344 10 false 3rd 2.344,2.823 2.802,3.021 0.458,0.198 10 false 5th 2.74,2.823 3.104,3.146 0.365,0.323 10 false 4th 3.313,2.823 4.938,3.229 1.625,0.406 10 false 5th (Brake Operating) 5.271,2.823 5.677,3.188 0.406,0.365 10 false 6th 5.823,2.708 6.906,3.094 1.083,0.385 10 false without Control 5.833,3.198 6.854,3.552 1.021,0.354 10 false with Control 1.438,3.323 1.771,3.615 0.333,0.292 10 false 4th 2.01,3.323 2.344,3.625 0.333,0.302 10 false 3rd 3.031,3.333 3.427,3.656 0.396,0.323 10 false 4th 4.198,3.323 4.531,3.646 0.333,0.323 10 false 3rd 4.677,3.323 5,3.646 0.323,0.323 10 false 4th 5.135,3.323 5.448,3.677 0.313,0.354 10 false 5th 5.448,3.323 5.76,3.656 0.313,0.333 10 false 6th


iv.

On models with the 2TR-FE engine, higher gear settings have been added for high speed gears (5th and 6th gears). In order to balance the reduction of additional drive force and the improvement of fuel efficiency when driving at high speeds, a high speed gear effective utilization control is used.


v.

By calculating the maximum additional drive force to be generated at high speed gears in a real-time manner, as well as determining the availability of high speed gears according to driving conditions (running resistance, driver's acceleration maneuvers), "balanced, improved fuel efficiency and driving capability" have been achieved.

·

Conditions Determining that Running in 6th Gear is Impossible (Examples)

X127573E04
1.021,1.833 2.542,2.219 1.521,0.385 10 false Heavy Load: 5th Gear 4.396,1.938 6.604,2.333 2.208,0.396 10 false Accelerating on Slope: 5th Gear

·

Conditions Determining that Running in 6th Gear is Possible

X127574E04
1.094,1.813 2.708,2.219 1.615,0.406 10 false Light Load: 6th Gear 4.26,1.969 6.646,2.385 2.385,0.417 10 false Constant Driving on Slope: 6th Gear



vi.

Sudden Accelerator Pedal Release Control (Models with 1GD-FTV or 1GR-FE Engine)

When the accelerator pedal is released suddenly, the transmission is kept in gear as long as possible, which improves engine braking force.

X114000E07
3.5,3.75 3.594,2.927 3.594,2.927 3.896,2.927 false 2.583,0.656 2.25,0.167 2.25,0.167 1.917,0.167 true 5,1.167 4.833,0.167 4.833,0.167 4.5,0.167 true 4,2.802 7.01,3.458 3.01,0.656 10 true Improved Response while Holding in Low Gear in Preparation for Re-acceleration 0.083,2.083 0.833,2.698 0.75,0.615 10 true Accelerator Pedal 0.083,4.135 1.115,4.542 1.031,0.406 10 true Gear Position 0.104,5 1,5.365 0.896,0.365 10 true Engine Speed 0.917,1.917 1.625,2.229 0.708,0.313 10 true Operated 0.917,2.438 1.625,2.75 0.708,0.313 10 true Released 5.917,0.219 6.833,0.448 0.917,0.229 10 true : with Control 5.917,0.552 6.969,0.792 1.052,0.24 10 true : without Control 1.583,4.531 1.917,4.729 0.333,0.198 10 true 4th 1.594,4.208 1.927,4.406 0.333,0.198 10 true 5th 1.573,3.917 1.906,4.115 0.333,0.198 10 true 6th 0.167,0.073 1.906,0.427 1.74,0.354 10 true Accelerator Pedal Released 2.75,0.073 4.49,0.427 1.74,0.354 10 true Accelerator Pedal Operated


vii.

Sudden Accelerator Pedal Depress Control (Models with 1GD-FTV or 1GR-FE Engine)

When the accelerator pedal is depressed suddenly, downshifting occurs earlier ensuring improved acceleration response.

X111662E04
1.698,0.26 2.01,0.458 0.313,0.198 10 false High 1.698,1.208 2.01,1.406 0.313,0.198 10 false Low 1.375,1.583 1.979,1.833 0.604,0.25 10 false Operated 1.375,2.083 2.031,2.292 0.656,0.208 10 false Released 1.75,2.469 2.063,2.667 0.313,0.198 10 false 6th 1.75,2.938 2.063,3.135 0.313,0.198 10 false 5th 4.438,3.281 6.656,3.594 2.219,0.313 10 false Improved Acceleration Response 6.083,0.458 7.042,0.667 0.958,0.208 10 true : with Control 6.083,0.708 7.115,1 1.031,0.292 10 true : without Control 0.469,0.719 1.615,0.938 1.146,0.219 10 false Vehicle Speed 0.052,1.76 1.354,2.146 1.302,0.385 10 false Accelerator Pedal 0.729,2.719 1.656,2.969 0.927,0.25 10 false Gear Position



i.

Multi-mode Automatic Transmission

i.

The driver can select the desired gear step by moving the shift lever "+" (forward) or to "-" (backward) while the shift lever is in S (6-speed sequential shiftmatic mode). Also, the shift paddle switch (transmission shift switch assembly) can be used to change the gear steps while the driver is holding the steering wheel.* Thus, the driver is able to change gear steps with a manual-like feel.

*: Models with shift paddle switch (transmission control switch)



ii.

6-speed sequential shiftmatic mode can be selected from normal driving mode by moving the shift lever to S. The driver can change the gear step by selecting it using the shift lever.


iii.

The driver selects S mode by moving the shift lever to S. At this time, the S4 or S5 range is selected in accordance with the vehicle speed.


iv.

The ECM will restrict the changing of the shift range if it detects a malfunction in the automatic transmission system.


v.

If the vehicle speed and engine speed exceed or go below a preset level in response to the driver's downshift operation request, changing the shift range will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.

X147444E04
0.677,2.146 2.208,3.469 1.531,1.323 10 false Ignition Advance Control Signal*1 or Fuel Injection Timing Control Signal*2 2.552,2.448 3.948,3.75 1.396,1.302 10 false Fluid Pressure Control and Solenoid Valve Control Signal 1.938,3.76 3.333,5.063 1.396,1.302 10 false Transmission 0.708,3.438 2.104,4.74 1.396,1.302 10 false Engine 5.385,2.458 6.656,3.906 1.271,1.448 10 false Shift Paddle Switch (Transmission Shift Switch Assembly)*3 1.385,1.344 2.917,2.667 1.531,1.323 10 false ECM 5.073,0.219 7.146,1.531 2.073,1.313 10 false Combination Meter Assembly 5.104,1.063 6.958,1.74 1.854,0.677 10 false Transmission Control Switch 2.917,1.188 5.063,2.448 2.146,1.26 10 false S Mode Position Signal 2.938,1.958 5.083,3.219 2.146,1.26 10 false Shift-down Signal 2.938,1.583 5.083,2.844 2.146,1.26 10 false Shift-up Signal 1.656,0.542 4.354,1.76 2.698,1.219 10 false CAN communication line 3.833,3.938 6.5,4.833 2.667,0.896 10 false *1: Models with 1GR-FE or 2TR-FE engine 3.844,4.333 6.646,5.25 2.802,0.917 10 false *2: Models with 2GD-FTV engine 3.844,4.75 6.927,5.667 3.083,0.917 10 false *3: Models with Shift Paddle Switch (Transmission Shift Switch Assembly)


vi.

The shift lever position and the shift range are indicated by the shift display in the combination meter assembly.


vii.

Blipping downshift control is used to improve shift change response and shift feeling in 6- speed sequential shiftmatic mode.


viii.

The blipping downshift control regulates each clutch and brake using the clutch to clutch pressure control, allowing them to be engaged smoothly and disengaged quickly. In addition, engine speed is boosted by powertrain cooperative control, thus ensuring engine brake force. In this way, a smooth and quick downshift is achieved. In addition, quicker downshifting has been made available by directly controlling clutch pressure.

HINT:

If ATF and engine coolant temperatures are low, the shift change response will be the same as when blipping downshift control is not available.


X127086E04
0.813,1.615 1.802,1.958 0.99,0.344 10 false Engine Speed 0.823,2.427 2.583,2.771 1.76,0.344 10 false Blipping Downshift Control 0.542,2.781 2.563,3.198 2.021,0.417 10 false Conventional Downshift Control 2.625,0.76 4.198,1.073 1.573,0.313 10 false Downshift Operation 4.948,0.094 6.802,0.448 1.854,0.354 10 false : Blipping downshift control 4.948,0.479 7.01,0.833 2.063,0.354 10 false : Conventional downshift control 5.448,2.458 7.073,2.844 1.625,0.385 10 false : Gear shift initiation time 5.448,2.927 6.75,3.344 1.302,0.417 10 false : Gear shift time 4.323,2.271 5.031,2.667 0.708,0.396 10 false Time 4.375,1.813 4.854,2.167 0.479,0.354 10 false 3rd 4.406,1.24 4.833,1.625 0.427,0.385 10 false 2nd



j.

D-range Paddle Active Control (Models with Shift Paddle Switch (Transmission Control Shift Switch Assembly))

i.

When the shift lever is in D, D-range paddle active control operates according to shift paddle switch (transmission shift switch assembly) operation and the system enters shift range selection mode. Shift paddle switch (transmission shift switch assembly) is provided on the back of the steering wheel to allow engine brake force control and downshift operations for acceleration to be performed while gripping the steering wheel.


ii.

The initial range when D-range paddle active control starts is determined according to the last gear position before shift paddle switch (transmission shift switch assembly) operation.

Initial Range when Control Starts
Gear Position before Shift Paddle Switch (Transmission Shift Switch Assembly) Operation Initial Range after Shift Paddle Switch (Transmission Shift Switch Assembly) "-" (Downshift) Operation
1st D1
2nd D1
3rd D2
4th D3
5th D4
6th D5


iii.

Normal driving automatically resumes (automatic shift control) in the following conditions:

Normal Driving (Automatic Shift Control) Recovery Conditions
Situation Condition
Vehicle Stop 1 second after the vehicle stops, normal driving (automatic shift control) resumes.
Shift Paddle Switch (Transmission Shift Switch Assembly) "+" (Upshift) Operation Operate and Hold for 1 Second or More When operated and hold for 1 second or more, normal driving (automatic shift control) resumes.
Continuous Accelerator Pedal Depression The driver depresses the accelerator pedal for more than a predetermined amount time.




FUNCTION


a.

Shift Lock System

i.

The shift lock system prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON and the brake pedal is depressed. This prevents the vehicle from starting off suddenly.


ii.

The shift lock system prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON and the brake pedal is depressed. This prevents the vehicle from starting off suddenly.

*: Models without entry and start system


iii.

The key interlock function prevents the key from being pulled out after the ignition switch has been turned off, unless the shift lever has been moved to P. Thus, the driver is urged to park the vehicle with the shift lever in P.


iv.

A shift lock release button, which manually overrides the shift lock mechanism, is used.

·

Models with Entry and Start System

X127059E05
0.427,0.323 2.344,0.708 1.917,0.385 10 false Stop Light Switch Assembly 0.385,1.063 2.188,1.635 1.802,0.573 10 false Certification ECU (Smart Key ECU Assembly) 0.313,2.167 2.542,2.5 2.229,0.333 10 false Engine Switch (Push Start Switch) 5.521,0.396 6.146,0.729 0.625,0.333 10 false Solenoid 5.302,1.135 6.76,1.479 1.458,0.344 10 false P Detection Switch 2.823,0.594 4.26,1.229 1.438,0.635 10 false Shift Lock Control ECU Sub-assembly 5.281,1.771 6.521,2.115 1.24,0.344 10 false Shift Lock Solenoid

·

Models without Entry and Start System

X127060E05
0.49,0.24 2.375,0.667 1.885,0.427 10 false Stop Light Switch Assembly 0.583,0.938 2.385,1.344 1.802,0.406 10 false Ignition Switch Assembly 5.521,0.24 6.323,0.635 0.802,0.396 10 false Solenoid 5.208,0.948 6.615,1.333 1.406,0.385 10 false P Detection Switch 2.854,0.406 4.313,1.323 1.458,0.917 10 false Shift Lock Control ECU Sub-assembly 5.115,2.219 6.729,2.635 1.615,0.417 10 false Key Interlock Solenoid 5.198,1.583 6.573,2 1.375,0.417 10 false Shift Lock Solenoid



v.

The shift lock control ECU sub-assembly uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and ignition switch. Upon receiving these signals, the shift lock control ECU sub-assembly turns on the shift lock solenoid and key interlock solenoid in order to release the shift lock and key interlock.

X127063E02
0.25,0.594 2.542,0.792 2.292,0.198 10 false Ignition Switch 0.25,1.469 2.542,1.667 2.292,0.198 10 false Stop Light Switch 0.25,2.177 2.542,2.375 2.292,0.198 10 false P Detection Switch 0.25,2.885 2.542,3.083 2.292,0.198 10 false Shift Lock Solenoid 0.25,3.583 2.542,3.781 2.292,0.198 10 false Key Interlock Solenoid* 2,0.583 2.542,0.917 0.542,0.333 10 false ACC 2,0.26 2.542,0.594 0.542,0.333 10 false IG 2,0.906 2.542,1.24 0.542,0.333 10 false OFF 2,1.302 2.542,1.635 0.542,0.333 10 false On 2,1.604 2.542,1.938 0.542,0.333 10 false Off 2,2.01 2.542,2.344 0.542,0.333 10 false On 2,2.323 2.542,2.656 0.542,0.333 10 false Off 2,2.719 2.542,3.052 0.542,0.333 10 false On 2,3.042 2.542,3.375 0.542,0.333 10 false Off 2,3.427 2.542,3.76 0.542,0.333 10 false On 2,3.76 2.542,4.094 0.542,0.333 10 false Off 0.271,4.365 3.688,4.667 3.417,0.302 10 false *: Models without entry and start system



b.

2nd Start Mode

i.

2nd start mode can be selected to make smooth starting off possible on surfaces with low friction coefficients, such as snow-covered roads.


ii.

When the 2nd start mode is selected while the shift lever is in D or in the S6, S5, S4, S3 or S2 range, the vehicle can start in the 2nd gear. After a start, if the shift lever is in D or in the S6, S5, S4 or S3 range, transmission will shift up automatically into 3rd, 4th, 5th or overdrive gears in the normal manner. If the shift lever is in the S2 range, the transmission will continue to operate in the 2nd gear.



c.

Drive Mode Select (Models with Drive Mode Select)

i.

The motive force characteristics for the accelerator opening angle can be changed through the selection of the drive mode according to driver preference.


ii.

An indicator is provided in the combination meter assembly and the drive mode the driver selected can be recognized.

X138131C01
2.208,3.25 2.521,3.448 0.313,0.198 10 false *a 4.729,3.229 5.042,3.427 0.313,0.198 10 false *b
*a Models without AVS *b Models with AVS


Drive Mode Powertrain Control Mode Outline

*1: Models with AVS

*2: Models without AVS

NORMAL Mode
COMF Mode*1
Normal This drive mode provides optimum driveability.
ECO Mode Eco The ECM optimizes fuel economy and driving performance by gradually generating the motive force in comparison to the accelerator pedal operation. At the same time, the ECM supports eco driving by optimizing air conditioning performance.
SPORT Mode*2
SPORT S/S+ Mode*1
Power The ECM controls motive force in the intermediate area of the accelerator pedal opening to a greater degree than that of NORMAL mode, improving acceleration performance. In addition, engine speed response performance has been improved in the high area of the accelerator pedal opening, thus producing a sporty drive.

HINT:

When the transfer is in L4F or L4L, drive mode select cannot be used.

When 2nd start mode is selected, powertrain control is performed according to 2nd start mode.





CONSTRUCTION


a.

Torque Converter

i.

A compact, lightweight and high-capacity torque converter assembly is used. The torque converter supports lock-up clutch control, thus improving fuel economy.


ii.

Laser welding has been used for the outer periphery of the torque convertor to suppress welding distortion and stabilize flex lock-up clutch control.

X127087E02
2.927,1.26 2.115,0.958 true 3.781,3.344 3.458,4.24 true 2.99,2.323 2.115,2.823 true 5.042,2.823 4.177,2.323 true 5,1.25 4.448,1.563 true 3.438,0.771 3.26,0.281 true 4.177,0.542 3.844,1.448 true 1.938,0.833 2.188,1.135 0.25,0.302 10 false *1 1.948,2.781 2.198,3.052 0.25,0.271 10 false *2 3.365,4.24 3.604,4.531 0.24,0.292 10 false *3 5.073,2.771 5.333,3.115 0.26,0.344 10 false *4 5.021,1.135 5.323,1.438 0.302,0.302 10 false *5 4.125,0.323 4.417,0.604 0.292,0.281 10 false *6 3.156,0.063 3.417,0.323 0.26,0.26 10 false *a

Text in Illustration
*1 Lock-up Clutch *2 Lock-up Damper
*3 1-way Clutch *4 Stator
*5 Pump Impeller *6 Turbine Runner
*a Laser Welded Portion - -



b.

Oil Pump

i.

The oil pump is operated by the torque converter assembly. The oil pump lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control. The front oil pump drive gear is continually driven by the engine via the pump impeller. The pump has sufficient capacity to supply the necessary fluid pressure throughout all speed ranges, as well as in reverse.

X127056E04
2.177,1.073 2.177,0.583 true 3.396,2.677 3.396,2.188 true 4.531,2.083 4.531,1.594 true 4.01,1.313 4.01,0.823 true 5.167,2.469 5.167,1.979 true 2.083,0.354 2.333,0.615 0.25,0.26 10 false *1 5.083,2.479 5.396,2.75 0.313,0.271 10 false *4 3.323,2.688 3.573,2.969 0.25,0.281 10 false *2 4.448,2.094 4.76,2.354 0.313,0.26 10 false *3 3.948,0.604 4.208,0.865 0.26,0.26 10 false *5

Text in Illustration
*1 Front Oil Pump Body Sub-assembly *2 Front Oil Pump Driven Gear
*3 Stator Shaft Assembly *4 Oil Pump Cover
*5 Front Oil Pump Drive Gear - -



c.

ATF Cooling System

i.

A water-cooled type ATF cooler built into the radiator is used on the models with 2TR-FE or 1GD-FTV engine.

X127677E02
5.979,0.76 5.396,0.969 true 3.656,1.604 3.385,2.073 true 2.917,2.208 2.76,2.479 true 2.635,2.458 2.938,2.698 0.302,0.24 10 false *1 6,0.625 6.24,0.917 0.24,0.292 10 false *2 3.656,1.406 3.906,1.698 0.25,0.292 10 false *3

Text in Illustration (Models with 2TR-FE Engine)
*1 Oil Cooler Inlet Tube Sub-assembly *2 Radiator Assembly
*3 Oil Cooler Outlet Tube Sub-assembly - -

X127678E02
3.646,1.625 3.479,2.104 true 4.865,0.583 4.385,0.302 true 3.313,2.167 3.219,2.427 true 3.104,2.427 3.344,2.677 0.24,0.25 10 false *1 4.208,0.167 4.469,0.406 0.26,0.24 10 false *2 3.625,1.406 3.885,1.667 0.26,0.26 10 false *3

Text in Illustration (Models with 1GD-FTV Engine)
*1 Oil Cooler Inlet Tube Sub-assembly *2 Radiator Assembly
*3 Oil Cooler Outlet Tube Sub-assembly - -


ii.

A water-cooled type ATF cooler and air-cooled type ATF cooler are used on all models excluding models for Europe or Chile with 1GR-FE engine.

X127679E02
3.083,2.021 2.76,2.396 true 6.135,1.406 5.344,1.115 true 5.833,0.344 5.063,0.625 true 3.333,1.531 3.021,1.906 true 2.625,2.385 2.865,2.625 0.24,0.24 10 false *1 6.167,1.375 6.427,1.656 0.26,0.281 10 false *2 5.854,0.208 6.135,0.49 0.281,0.281 10 false *3 3.354,1.375 3.615,1.656 0.26,0.281 10 false *4

Text in Illustration (except Models for Europe or Chile with 1GR-FE Engine)
*1 Oil Cooler Inlet Tube Sub-assembly *2 Oil Cooler Assembly
*3 Radiator Assembly *4 Oil Cooler Outlet Tube Sub-assembly


iii.

A water-cooled type ATF cooler and ATF warmer (transmission oil cooler with thermostat assembly) are used on the models for Europe or Chile with 1GR-FE engine.

X127680E02
2.323,2.219 1.646,2.469 true 3.438,1.979 3.188,2.406 true 5.958,0.698 5.333,0.927 true 1.479,2.375 1.677,2.625 0.198,0.25 10 false *1 3.083,2.406 3.313,2.688 0.229,0.281 10 false *2 5.969,0.573 6.198,0.833 0.229,0.26 10 false *3

Text in Illustration (Models for Europe or Chile with 1GR-FE Engine)
*1 ATF Warmer (Transmission Oil Cooler with Thermostat Assembly) *2 Oil Cooler Tube Sub-assembly
*3 Radiator Assembly - -


iv.

The ATF warmer (transmission oil cooler with thermostat assembly) uses engine coolant that has been warmed by the engine to warm up the ATF quickly. Consequently, the friction losses of the automatic transmission are quickly reduced, thus improving fuel economy.


v.

The ATF warmer (transmission oil cooler with thermostat assembly) has a thermostat that changes the route through which the ATF flows.

X127681E02
5.958,3.833 5.604,3.219 true 2.365,2.188 2.156,2.76 true 2.208,3.656 2.063,4.073 true 5.948,3.833 6.25,4.167 0.302,0.333 10 false *1 1.958,4.073 2.219,4.333 0.26,0.26 10 false *2 2.333,1.948 2.635,2.229 0.302,0.281 10 false *3 0.792,2.229 1.063,2.49 0.271,0.26 10 false *a 0.5,2.708 0.729,3 0.229,0.292 10 false *b 0.99,3.063 1.198,3.313 0.208,0.25 10 false *c 1.115,3.563 1.333,3.833 0.219,0.271 10 false *d 3.438,2.375 3.698,2.677 0.26,0.302 10 false *e 3.177,2.01 3.365,2.219 0.188,0.208 10 false *f

Text in Illustration
*1 Transmission Oil Cooler with Thermostat Assembly *2 Thermostat
*3 Transmission Oil Cooler - -
*a To Transmission *b From Transmission
*c To Engine *d From Heater Core
*e To Radiator *f From Radiator
V100135

ATF Flow
V100136

Engine Coolant Flow


vi.

When the ATF temperature is low, it is heated by the ATF warmer (transmission oil cooler with thermostat assembly) using the engine coolant, and when the ATF temperature is high, it is cooled down by the ATF warmer (transmission oil cooler with thermostat assembly) and radiator (water-cooled type ATF cooler).

X102186E05
0.979,0.542 1.25,0.844 0.271,0.302 10 false *1 1.01,1.375 1.292,1.677 0.281,0.302 10 false *3 2.427,0.51 2.698,0.802 0.271,0.292 10 false *2 2.406,2.052 2.74,2.313 0.333,0.26 10 false *4 4.5,0.552 4.792,0.833 0.292,0.281 10 false *1 0.292,0.25 0.573,0.573 0.281,0.323 10 false *a 3.802,0.24 4.177,0.542 0.375,0.302 10 false *b 4.542,1.396 4.865,1.667 0.323,0.271 10 false *3 5.958,0.542 6.271,0.844 0.313,0.302 10 false *2 5.948,2.115 6.292,2.396 0.344,0.281 10 false *4

Text in Illustration
*1 Transmission *2 ATF Warmer (Transmission Oil Cooler with Thermostat Assembly)
*3 Thermostat *4 Radiator (Water-cooled Type ATF Cooler)
*a ATF Temperature is Low *b ATF Temperature is High


vii.

The thermostat consists of a poppet valve, a bypass valve and an element case (contains wax). When the ATF temperature changes from low to high, the wax will expand to start to open the poppet valve and close the bypass valve, thus switching the ATF passages.

X102187E05
2.365,1.708 2.365,1.177 2.365,1.177 2.479,1.177 true 1.708,1.698 1.708,1.177 1.708,1.177 1.594,1.177 true 1.948,1.99 1.708,3.302 1.708,3.302 1.438,3.302 true 2.688,3.052 2.781,3.292 2.781,3.292 2.979,3.292 true 1.156,1.74 0.917,1.583 0.917,1.583 0.646,1.583 true 5.854,1.708 5.854,1.177 5.854,1.177 5.969,1.177 true 5.198,1.698 5.198,1.177 5.198,1.177 5.083,1.177 true 5.458,1.99 5.74,3.302 5.74,3.302 4.948,3.302 true 6.167,3.073 6.26,3.313 6.26,3.313 6.458,3.313 true 4.646,1.76 4.417,1.604 4.417,1.604 4.135,1.604 true 0.292,0.24 0.563,0.51 0.271,0.271 10 false *a 2.073,0.281 2.365,0.573 0.292,0.292 10 false *g 2.865,0.646 3.115,0.948 0.25,0.302 10 false *h 2.854,1.865 3.104,2.125 0.25,0.26 10 false *i 2.854,2.302 3.115,2.594 0.26,0.292 10 false *j 2.521,1.094 2.813,1.375 0.292,0.281 10 false *e 1.427,1.052 1.656,1.344 0.229,0.292 10 false *c 1.26,3.188 1.51,3.438 0.25,0.25 10 false *2 3.021,3.188 3.281,3.49 0.26,0.302 10 false *3 0.469,1.479 0.708,1.74 0.24,0.26 10 false *1 3.813,0.25 4.156,0.594 0.344,0.344 10 false *b 5.563,0.271 5.844,0.552 0.281,0.281 10 false *g 6.344,0.656 6.635,0.948 0.292,0.292 10 false *h 6.354,1.854 6.594,2.125 0.24,0.271 10 false *i 6.354,2.302 6.625,2.635 0.271,0.333 10 false *j 6.021,1.094 6.302,1.385 0.281,0.292 10 false *f 4.906,1.073 5.135,1.417 0.229,0.344 10 false *d 4.771,3.188 5.021,3.448 0.25,0.26 10 false *2 6.5,3.219 6.74,3.542 0.24,0.323 10 false *3 3.958,1.5 4.188,1.844 0.229,0.344 10 false *1

Text in Illustration
*1 Thermostat *2 Element Case (Contains Wax)
*3 ATF Warmer (Transmission Oil Cooler with Thermostat Assembly) - -
*a ATF Temperature is Low *b ATF Temperature is High
*c Poppet Valve: Closed *d Poppet Valve: Open
*e Bypass Valve: Open *f Bypass Valve: Closed
*g From Transmission *h To Transmission
*i To Radiator (Water-cooled Type ATF Cooler) *j From Radiator (Water-cooled Type ATF Cooler)
V100135

ATF Flow - -



d.

ATF Filling Procedures

i.

An ATF filling procedure is used in order to improve the accuracy of the ATF level when the transmission is being repaired or replaced. As a result, the oil filler tube and the oil level gauge used in the conventional automatic transmission have been discontinued, eliminating the need to inspect the fluid level as a part of routine maintenance. For details about the ATF filling procedures, refer to the Repair Manual.

X127682E02
2.427,1.635 2.083,0.708 true 3.677,3.313 3.469,2.74 true 1.958,0.51 2.229,0.771 0.271,0.26 10 false *1 3.625,3.323 3.906,3.594 0.281,0.271 10 false *2

Text in Illustration
*1 Refill Plug *2 Overflow Plug



e.

Planetary Gear Unit

i.

The gear train consists of 2 multi-plate clutches, 3 multi-plate brakes, a 1-way clutch and 3 sets of planetary gears, each consisting of a sun gear, a pinion gear and a ring gear.

X127088E03
1.76,1.313 1.76,0.448 true 3.188,1.313 3.188,0.448 true 3.719,1.323 3.719,0.458 true 4.969,1.51 4.969,0.479 true 4.5,1.969 4.5,0.458 true 2.052,3.01 2.052,1.74 true 2.844,3.063 2.844,2.115 true 3.708,3.042 3.708,2.115 true 5.073,3.031 5.073,2.104 true 4.042,3.063 4.042,2.521 true 1.667,0.24 1.896,0.521 0.229,0.281 10 false *1 3.073,0.219 3.406,0.448 0.333,0.229 10 false *10 3.646,0.24 3.948,0.531 0.302,0.292 10 false *9 4.427,0.219 4.667,0.427 0.24,0.208 10 false *8 4.906,0.271 5.146,0.542 0.24,0.271 10 false *7 1.969,3.021 2.208,3.323 0.24,0.302 10 false *2 2.76,3.073 3.021,3.375 0.26,0.302 10 false *3 3.625,3.052 3.896,3.333 0.271,0.281 10 false *4 3.969,3.073 4.24,3.344 0.271,0.271 10 false *5 5,3.042 5.271,3.333 0.271,0.292 10 false *6

Text in Illustration
*1 No. 2 Clutch (C2) *2 No. 1 Clutch (C1)
*3 Front Planetary Gear Assembly *4 Center Planetary Gear Assembly
*5 Intermediate Shaft *6 Rear Planetary Gear Assembly
*7 No. 2 Brake (B2) *8 1-way Clutch Assembly
*9 No. 4 Brake (B4) *10 No. 1 Brake (B1)

X150070E01
2.021,1.771 1.521,2.188 true 2.667,1.885 2.396,2.344 true 3.323,2.156 3.208,2.479 true 4.792,2.438 4.667,2.094 true 5.792,2.406 5.573,2.042 true 6.667,2.104 6.281,1.781 true 0.906,1.667 0.531,1.344 true 3.042,1.427 2.927,1.104 true 4.75,1.052 4.594,1.479 true 0.385,1.188 0.656,1.438 0.271,0.25 10 false *1 1.365,2.177 1.656,2.469 0.292,0.292 10 false *2 2.25,2.344 2.552,2.594 0.302,0.25 10 false *3 3.083,2.479 3.385,2.719 0.302,0.24 10 false *4 4.76,2.448 5.313,2.635 0.552,0.188 10 false *5 5.74,2.417 6.292,2.604 0.552,0.188 10 false *6 6.667,2.094 6.927,2.344 0.26,0.25 10 false *7 4.708,0.854 5,1.104 0.292,0.25 10 false *8 2.823,0.906 3.115,1.208 0.292,0.302 10 false *9

Text in Illustration
*1 Input Shaft *2 Intermediate Shaft
*3 Front Planetary Sun Gear *4 Front Planetary Gear Assembly
*5 Center Planetary Gear Assembly *6 Rear Planetary Gear Assembly
*7 Output Shaft *8 Center Planetary Carrier
*9 Front Planetary Carrier - -



f.

Centrifugal Fluid Pressure Canceling Mechanism

i.

A centrifugal fluid pressure canceling mechanism is used on the C1 and C2 clutches that are applied when shifting 3rd-4th and 4th-5th.


ii.

Clutch shifting operation is affected not only by the valve body controlling fluid pressure but also by centrifugal fluid pressure that is present due to fluid in the clutch piston oil pressure chamber. The centrifugal fluid pressure canceling mechanism uses chamber B to reduce the effect applied to chamber A. As a result, smooth shifting with excellent response has been achieved.

X127097E02
1.167,1.896 0.917,2.594 true 2.094,2.708 1.802,1.906 true 2.625,2.646 1.906,1.792 true 1.688,1.073 1.583,0.771 true 2.073,0.75 1.969,1.052 true 2.688,0.854 2.01,1.427 true 3.042,1.188 2.375,1.438 true 1.417,1.417 0.938,0.844 true 1.479,0.563 1.708,0.813 0.229,0.25 10 false *1 0.802,0.667 1.052,0.927 0.25,0.26 10 false *2 0.823,2.594 1.094,2.865 0.271,0.271 10 false *3 2.031,2.719 2.271,2.979 0.24,0.26 10 false *4 2.615,2.635 2.896,2.938 0.281,0.302 10 false *5 3.073,1.073 3.313,1.365 0.24,0.292 10 false *6 2.698,0.698 2.948,0.958 0.25,0.26 10 false *7 2.063,0.563 2.333,0.823 0.271,0.26 10 false *8

Text in Illustration
*1 Piston (for C2) *2 Chamber B (for C2)
*3 Chamber A (for C2) *4 Chamber A (for C1)
*5 Chamber B (for C1) *6 No. 1 Clutch (C1)
*7 Piston (for C1) *8 No. 2 Clutch (C2)


iii.

Chamber B is filled by fluid supplied to the shaft for lubrication. As a result of filling chamber B, the same amount of fluid pressure is present on both sides of the piston due to centrifugal force. This cancels the effects of fluid pressure on the piston caused by centrifugal force. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and highly responsive and smooth shifting characteristics are achieved.

U116711E10
3.802,0.302 3.969,0.302 3.969,0.302 3.969,0.635 true 3.729,1.5 3.552,1.5 3.552,1.5 3.552,1.167 true 2.719,0.438 3,0.438 3,0.438 3,1.313 true 1.135,1.26 1.594,1.26 true 1.75,2.667 2.25,2.667 2.25,2.667 2.25,2.385 false 4.844,3.521 6.396,4.313 1.552,0.792 10 false Target fluid pressure (original clutch pressure) 2.552,3.542 4.083,4.323 1.531,0.781 10 false Centrifugal fluid pressure applied chamber B 5.063,1.729 6.688,2.594 1.625,0.865 10 false : Centrifugal fluid pressure applied to chamber B 5.063,1.083 6.688,1.802 1.625,0.719 10 false : Centrifugal fluid pressure applied to chamber A 5.042,0.448 6.75,0.917 1.708,0.469 10 false : Target fluid pressure 3.333,0.198 3.875,0.531 0.542,0.333 10 false Clutch 3.792,1.396 4.333,1.802 0.542,0.406 10 false Piston 0.875,0.323 2.646,1.094 1.771,0.771 10 false Chamber B (Centrifugal Fluid Pressure Chamber) 0.302,1.167 1.115,2.542 0.813,1.375 10 false Chamber A (Piston Fluid Pressure Chamber) 0.656,2.563 1.729,3.156 1.073,0.594 10 false Fluid Pressure Applied to Piston 2.844,2.698 3.667,3.083 0.823,0.385 10 false Shaft Side 0.771,3.521 1.802,4.313 1.031,0.792 10 false Fluid pressure applied to piston



g.

Transmission Valve Body Assembly

i.

The transmission valve body assembly consists of upper and lower valve bodies and 7 solenoid valves.

X127098E03
3.042,1.302 2.813,0.667 true 2.542,1.427 2.177,0.792 true 2.021,1.552 1.542,0.979 true 1.469,1.719 0.938,1.26 true 0.979,1.865 0.573,1.625 true 3.594,1.156 3.594,0.552 true 4.292,0.615 4.031,1.073 true 6.24,1.969 5.552,2.365 true 4.385,4.146 4.385,3.5 true 2.708,0.458 2.969,0.74 0.26,0.281 10 false *1 2.052,0.604 2.323,0.896 0.271,0.292 10 false *2 1.417,0.792 1.667,1.094 0.25,0.302 10 false *3 0.792,1.083 1.063,1.354 0.271,0.271 10 false *4 0.417,1.479 0.698,1.781 0.281,0.302 10 false *5 4.323,4.167 4.594,4.406 0.271,0.24 10 false *6 6.26,1.844 6.5,2.156 0.24,0.313 10 false *7 4.302,0.458 4.583,0.719 0.281,0.26 10 false *8 3.531,0.302 3.823,0.573 0.292,0.271 10 false *9

Text in Illustration
*1 Solenoid valve (SLU) *2 Solenoid valve (SL3)
*3 Solenoid valve (SL1) *4 Solenoid valve (SL2)
*5 Solenoid valve (SLT) *6 Lower Valve Body
*7 Upper Valve Body *8 Solenoid valve (SL)
*9 Solenoid valve (SL4) - -

X127100E03
1.427,0.958 0.75,0.563 true 2.083,2.792 1.302,3.25 true 2.396,2.885 1.885,3.479 true 3.583,2.302 3.156,3.49 true 4.177,2.604 4.021,3.49 true 4.792,3.479 4.646,2.625 true 5.281,3.479 5.063,2.875 true 6.448,3.052 5.5,2.51 true 6.156,0.479 5.354,0.938 true 5.448,0.333 4.906,0.792 true 4.948,0.333 4.427,0.958 true 4.271,0.333 3.958,0.865 true 3.01,1.333 2.635,0.313 true 1.927,0.906 1.458,0.344 true 2.521,0.094 2.792,0.354 0.271,0.26 10 false *1 1.323,0.167 1.625,0.427 0.302,0.26 10 false *2 0.583,0.406 0.854,0.698 0.271,0.292 10 false *3 1.125,3.188 1.438,3.469 0.313,0.281 10 false *4 1.75,3.469 2.042,3.708 0.292,0.24 10 false *5 3.052,3.49 3.292,3.719 0.24,0.229 10 false *6 3.927,3.49 4.198,3.729 0.271,0.24 10 false *7 4.74,3.49 4.958,3.708 0.219,0.219 10 false *8 5.229,3.479 5.49,3.74 0.26,0.26 10 false *9 6.479,3 6.833,3.302 0.354,0.302 10 false *10 6.167,0.344 6.49,0.646 0.323,0.302 10 false *11 5.458,0.188 5.792,0.49 0.333,0.302 10 false *12 4.885,0.125 5.188,0.375 0.302,0.25 10 false *13 4.198,0.135 4.531,0.396 0.333,0.26 10 false *14

Text in Illustration (Upper Valve Body)
*1 Lock-up Relay Valve *2 Secondary Regulator Valve
*3 C2 Damper *4 SLT Damper
*5 B2 Damper *6 Lock-up Control Valve
*7 B4 Apply Control Valve *8 B4 Control Valve
*9 B1, B4 Apply Control Valve *10 Solenoid Relay Valve
*11 Solenoid Modulator Valve *12 B1 Apply Control Valve
*13 Clutch Control Valve *14 Sequence Valve

X127101E03
2.292,2.396 0.969,2.875 true 4.292,1.958 3.844,3.188 true 5,3.156 4.521,2.333 true 6.219,0.802 5.125,1.198 true 0.792,2.792 1.052,3.052 0.26,0.26 10 false *1 3.729,3.188 4,3.479 0.271,0.292 10 false *2 4.979,3.167 5.24,3.438 0.26,0.271 10 false *3 6.24,0.646 6.51,0.938 0.271,0.292 10 false *4

Text in Illustration (Lower Valve Body)
*1 Primary Regulator Valve *2 B2 Apply Control Valve
*3 C1 Accumulator *4 B1 Damper



h.

Solenoid valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU)

i.

Solenoid valves have been provided for controlling clutch engagement hydraulic pressure (SL1, SL2), lock-up clutch (SLU), line hydraulic pressure (SLT), and brake engagement hydraulic pressure (SL3, SL4).


ii.

By directly controlling the hydraulic pressure for each clutch and brake with high flow rate solenoid valves (SL1), (SL2), (SL3), (SL4), shift-change responsiveness has been improved, shift shocks have been reduced, and the structure has been simplified through the reductions of oil passage lengths and the numbers of components.

·

Solenoid Valves (SL1), (SL2), (SL3) and (SL4)

X127102E07
1.146,1.229 1.146,0.563 1.146,0.563 1.323,0.563 true 1.063,1.719 1.24,1.719 1.24,1.719 1.24,1.5 true 1.365,0.469 3.052,0.667 1.688,0.198 10 false Spool Valve 0.625,1.615 1.167,1.927 0.542,0.313 10 false Sleeve 3.698,0.708 4.292,1.708 0.594,1 10 false Hydraulic Pressure 5.573,2.104 6.188,2.438 0.615,0.333 10 false Current

·

Solenoid Valve (SLT)

X127103E07
1.271,1.156 1.271,0.521 1.271,0.521 1.479,0.521 true 1.156,1.698 1.333,1.698 1.333,1.698 1.333,1.458 true 1.531,0.427 2.5,0.833 0.969,0.406 10 false Spool Valve 0.708,1.594 1.24,1.958 0.531,0.365 10 false Sleeve 3.688,0.521 4.281,1.813 0.594,1.292 10 false Hydraulic Pressure 5.479,2.083 6.188,2.479 0.708,0.396 10 false Current

·

Solenoid Valve (SLU)

X127104E06
1.25,1.156 1.25,0.542 1.25,0.542 1.448,0.542 true 1.208,1.667 1.375,1.667 1.375,1.667 1.375,1.438 true 1.5,0.438 2.458,0.771 0.958,0.333 10 false Spool Valve 0.76,1.563 1.302,1.948 0.542,0.385 10 false Sleeve 3.708,0.708 4.313,1.906 0.604,1.198 10 false Hydraulic Pressure 5.583,2.094 6.25,2.448 0.667,0.354 10 false Current


Function of Solenoid Valves
Solenoid Valve Function
Solenoid Valve (SL1) Performs shift controls.
Solenoid Valve (SL2) Performs shift controls.
Solenoid Valve (SL3) Performs shift controls.
Solenoid Valve (SL4) Performs shift controls.
Solenoid Valve (SLT) Performs line pressure controls.
Solenoid Valve (SLU)
·

Performs lock-up clutch controls.

·

Performs B2 brake hydraulic pressure controls (only for the 1st range when the shift lever is in S).





i.

Solenoid Valve (SL)

i.

A transmission 3-way solenoid (SL) has been provided for switching lock-up hydraulic pressure and B2 brake hydraulic pressure.

X127105E04
3.135,0.792 3.313,0.385 3.313,0.385 3.51,0.385 true 3.021,1.365 2.698,1.74 2.698,1.74 2.5,1.74 true 1.646,1.198 2.615,1.573 0.969,0.375 10 false Line Pressure 3.563,0.292 4.865,0.75 1.302,0.458 10 false Control Pressure 1.979,1.635 2.646,2.01 0.667,0.375 10 false Strainer 2.99,1.875 3.448,2.26 0.458,0.385 10 false Drain

Function of Solenoid Valve
Solenoid Valve Function
Solenoid Valve (SL) Shifts between lock-up hydraulic pressure and B2 brake hydraulic pressure.



j.

ATF Temperature Sensor

i.

The ATF temperature sensors are used for hydraulic pressure control. These sensors are used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.

X127099E03
2.896,2.625 2.01,3.365 true 5.094,0.656 4.125,1.469 true 1.865,3.323 2.083,3.583 0.219,0.26 10 false *1 5.125,0.531 5.417,0.792 0.292,0.26 10 false *2

Text in Illustration
*1 No. 2 ATF Temperature Sensor *2 No. 1 ATF Temperature Sensor
V100135

Engine Side - -



k.

Park/Neutral Position Switch

i.

The park/neutral position switch assembly sends the P, R, N, D and NSW signals to the ECM.

X127057E05
0.052,0.688 0.708,1.51 0.656,0.823 10 false To Starter Relay 0.479,1.875 0.771,2.24 0.292,0.365 10 false +B 1.083,0.906 1.385,1.198 0.302,0.292 10 false L 1.354,2.958 2.667,3.74 1.313,0.781 10 false Park/Neutral Position Switch Assembly 2.844,0.906 3.146,1.219 0.302,0.313 10 false B 2.844,1.333 3.115,1.615 0.271,0.281 10 false PL 2.844,1.771 3.198,2.104 0.354,0.333 10 false RL 2.844,2.198 3.156,2.542 0.313,0.344 10 false NL 2.844,2.635 3.167,2.917 0.323,0.281 10 false DL 4.01,1.594 4.479,2.031 0.469,0.438 10 false ECM 4.198,0.583 4.625,0.927 0.427,0.344 10 false STA 3.229,0.906 3.708,1.281 0.479,0.375 10 false NSW 3.448,1.333 3.76,1.625 0.313,0.292 10 false P 3.448,1.76 3.74,2.042 0.292,0.281 10 false R 3.448,2.198 3.76,2.458 0.313,0.26 10 false N 3.448,2.635 3.708,2.938 0.26,0.302 10 false D 4.708,1.833 5.635,3.26 0.927,1.427 10 false CAN communication line 5.813,1.26 6.646,2.583 0.833,1.323 10 false Combination Meter Assembly



l.

Transmission Control Switch

i.

The transmission control switch is installed inside the transmission floor shift assembly to detect the S mode position and inform the ECM.


ii.

The transmission control switch detects whether the shift lever is in D or S, and detects the operating conditions of the shift lever ["+" (forward) or "-" (backward)] when the shift lever is in S, and sends signals to the ECM.

X127058E10
0.302,0.677 0.615,0.969 0.313,0.292 10 false +B 1.031,0.781 1.281,1.031 0.25,0.25 10 false IG 2.51,0.771 2.792,1.021 0.281,0.25 10 false S 2.51,1.188 3.042,1.5 0.531,0.313 10 false SFTU 2.51,1.583 3.042,1.896 0.531,0.313 10 false SFTD 3.469,0.771 3.698,1.031 0.229,0.26 10 false S 3.208,1.177 3.75,1.5 0.542,0.323 10 false SFTU 3.208,1.583 3.74,1.979 0.531,0.396 10 false SFTD 0.958,2.031 2.958,2.458 2,0.427 10 false Transmission Control Switch 3.979,0.99 4.531,1.458 0.552,0.469 10 false ECM 4.729,1.229 5.604,2.24 0.875,1.01 10 false CAN communication line 5.813,0.594 6.646,1.875 0.833,1.281 10 false Combination Meter Assembly



m.

Shift Paddle Switch (Models with Shift Paddle Switch (Transmission Shift Switch Assembly))

i.

The shift paddle switch (transmission shift switch assembly) is installed in the steering wheel. The shift paddle switch (transmission shift switch assembly) detects the operating conditions of the shift paddle "+" (upshift) or "-" (downshift) when the shift lever is in D or S, and sends the SFTU and SFTD signals to the ECM.

X127694E06
0.958,1.74 2.708,2.083 1.75,0.344 10 false Transmission Control Switch 0.917,3.302 4.51,3.646 3.594,0.344 10 false Shift Paddle Switch (Transmission Shift Switch Assembly) 0.313,0.458 0.563,0.802 0.25,0.344 10 false +B 1.031,0.583 1.281,0.927 0.25,0.344 10 false IG 2.5,0.979 2.917,1.323 0.417,0.344 10 false SFTU 3.458,0.573 3.708,0.917 0.25,0.344 10 false S 3.219,0.979 3.635,1.323 0.417,0.344 10 false SFTU 2.5,1.375 2.917,1.719 0.417,0.344 10 false SFTD 3.219,1.375 3.635,1.719 0.417,0.344 10 false SFTD 3.969,0.74 4.385,1.083 0.417,0.344 10 false ECM 4.719,1.063 5.667,1.74 0.948,0.677 10 false CAN communication line 5.698,0.552 6.583,1.646 0.885,1.094 10 false Combination Meter Assembly



n.

Transmission Revolution Sensor

i.

This automatic transmission uses a transmission revolution sensor (for NT signal) and a transmission revolution sensor (for SP2 signal). Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions.


ii.

These transmission revolution sensors are the pick-up coil type.


iii.

The transmission revolution sensor (for NT signal) detects the input speed of the transmission. The direct clutch drum sub-assembly is used as the timing rotor for this sensor.


iv.

The transmission revolution sensor (for SP2 signal) detects the output speed of the transmission. The parking lock gear on the rear planetary gear is used as the timing rotor for this sensor.

X127106E02
4.323,2.99 3.698,1.917 true 3.313,1.115 2.969,0.521 true 4.156,1.01 3.865,0.51 true 5.625,2.563 5,1.49 true 2.844,0.323 3.094,0.604 0.25,0.281 10 false *1 3.729,0.302 3.99,0.552 0.26,0.25 10 false *4 4.323,3 4.615,3.271 0.292,0.271 10 false *2 5.604,2.563 5.906,2.813 0.302,0.25 10 false *3

Text in Illustration
*1 Direct Clutch Drum Sub-assembly *2 Transmission Revolution Sensor (NT)
*3 Parking Lock Gear *4 Transmission Revolution Sensor (SP2)



o.

Shift Control Mechanism

i.

A gate type shift lever is used.


ii.

The shift control mechanism consists of a transmission floor shift assembly and a transmission control cable assembly.

X138509E01
2.052,3.021 3.031,2.438 true 4.438,1.875 5.229,1.344 true 5.24,1.219 5.552,1.417 0.313,0.198 10 false *2 1.896,2.979 2.208,3.177 0.313,0.198 10 false *1

Text in Illustration
*1 Transmission Control Cable Assembly *2 Transmission Floor Shift Assembly




OPERATION


a.

Transmission Power Flow

Shift Position and Gear Position Shift Solenoid Valve
SL1 SL2 SL3 SL4 SL SLU
P - - - - - -
R - - - ○ - -
N - - - - - -
D.S 1st ○ - - - - ●
2nd ○ - ○ - ○ -
3rd ○ - - ○ ○ -
4th ○ ○ - - ○ ○
5th - ○ - ○ ○ ○
6th - ○ ○ - ○ ○

HINT:

○: Operates

●: Operates during Engine Braking


Shift Position and Gear Position Clutch Brake 1-way Clutch
C1 C2 B1 B2 B4 F1
P - - - - - -
R - - - ○ ○ -
N - - - - - -
D.S 1st ○ - - ● - ○
2nd ○ - ○ - - -
3rd ○ - - - ○ -
4th ○ ○ - - - -
5th - ○ - - ○ -
6th - ○ ○ - - -

HINT:

○: Operates

●: Operates during Engine Braking


i.

1st Gear (Shift Lever in D or S)

X150071

Text in Illustration
V100144

Operates
V100143

Operates during Engine Braking


ii.

2nd Gear (Shift Lever in D or S)

X150072

Text in Illustration
V100144

Operates - -


iii.

3rd Gear (Shift Lever in D or S)

X150073

Text in Illustration
V100144

Operates - -


iv.

4th Gear (Shift Lever in D or S)

X150074

Text in Illustration
V100144

Operates - -


v.

5th Gear (Shift Lever in D or S)

X150075

Text in Illustration
V100144

Operates - -


vi.

6th Gear (Shift Lever in D or S)

X150076

Text in Illustration
V100144

Operates - -


vii.

Reverse Gear (Shift Lever in R)

X150077

Text in Illustration
V100144

Operates - -




FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs can be read by connecting a Global TechStream (GTS) to the DLC3.


c.

For details, refer to the Repair Manual.