Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION SYSTEM › from 2020.08
NM27T0E _52 Drivetrain _053615 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260146 MANUAL TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

RA61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION


a.

Gear Shift Indicator (Models for Europe)

i.

In the Gear Shift Indicator, the ECM calculates an environmentally favorable shift position based on the vehicle conditions, and makes a request to the combination meter assembly to indicate upshifting or downshifting. Then the Gear Shift Indicator in the combination meter gives a shifting recommendation to the driver.


ii.

The ECM determines the actual gear position based on the signals from the crankshaft position sensor and speed sensors, and the target gear position based on the signals from the accelerator pedal position sensor and speed sensors.


iii.

By driving in accordance with the shift change recommendations indicated by the Gear Shift Indicator, the driver can enhance, fuel economy and reduce exhaust gas output as much as possible.

X147476E01
0.802,7.385 4.302,7.854 3.5,0.469 10 false : CAN communication line 3.417,3.365 6.917,3.833 3.5,0.469 10 false ECM 0.625,6.156 4.125,6.625 3.5,0.469 10 false Back-up Light Switch Assembly 5.208,6.635 7.115,7.385 1.906,0.75 10 false Gear Shift Indicator 4.875,4.729 7.146,5.75 2.271,1.021 10 false Combination Meter Assembly 5.198,3.698 7.156,4.479 1.958,0.781 10 false Skid Control ECU 5.292,2.771 7.156,3.552 1.865,0.781 10 false Speed Sensors 5.208,0.51 7.073,1.292 1.865,0.781 10 false 4WD Control ECU 5.083,1.604 6.573,2.323 1.49,0.719 10 false Central Gateway ECU (Network Gateway ECU) 0.854,4.74 4.354,5.208 3.5,0.469 10 false Clutch Switch Assembly 0.719,3.396 4.219,3.865 3.5,0.469 10 false Stop Light Switch Assembly 0.813,0.469 4.313,0.938 3.5,0.469 10 false Crankshaft Position Sensor 0.51,2.021 4.073,2.635 3.563,0.615 10 false Accelerator Pedal Sensor Assembly


iv.

The Gear Shift Indicator will not effect control while the vehicle is being driven in reverse.


v.

The Gear Shift Indicator will not effect control while the vehicle is stopped or the clutch is not engaged while shifting.


vi.

The Gear Shift Indicator will not effect control while the transfer position switch in L4.


vii.

Upon receiving a shift instruction request from the ECM, the combination meter assembly will illuminate the Gear Shift Indicator.


viii.

The 2 indicator lights illuminate simultaneously during a bulb check.

X100547E03
1.563,1.042 1.771,0.958 true 1.281,1.781 1.5,1.698 true 1.833,0.813 2.125,1.125 0.292,0.313 10 false A 1.115,1.74 1.469,2.104 0.354,0.365 10 false B 3.021,0.542 4.656,0.906 1.635,0.365 10 false Illumination Location 3.583,1.01 4.354,1.375 0.771,0.365 10 false A 3.604,1.427 4.344,1.792 0.74,0.365 10 false B 3.427,1.865 4.438,2.229 1.01,0.365 10 false A and B 4.833,0.542 6.677,0.906 1.844,0.365 10 false Instruction Description 4.771,1 6.708,1.365 1.938,0.365 10 false Shift-up Recommendation 4.635,1.417 6.698,1.781 2.063,0.365 10 false Shift-down Recommendation 5.177,1.844 6.625,2.208 1.448,0.365 10 false Bulb Check 0.958,2.167 2.875,2.531 1.917,0.365 10 false Gear Shift Indicator




CONSTRUCTION


a.

Gear Train

i.

The transmission synchromesh mechanism is an all-speed constant meshing type.

U170788E03
5.042,3.354 4.885,3.354 4.885,3.354 4.615,2.458 true 1.469,0.354 1.646,0.354 1.646,0.354 2.844,2.073 true 0.708,0.365 0.875,0.365 0.875,0.365 2.094,1.906 true 2.177,0.344 2.313,0.344 2.313,0.344 3.073,2.031 true 2.813,0.365 2.979,0.365 2.979,0.365 3.448,2.104 true 3.74,0.323 3.563,0.323 3.563,0.323 3.563,1.656 true 4.448,0.323 4.281,0.323 4.281,0.323 3.885,1.698 true 5.146,0.333 4.969,0.333 4.969,0.333 4.083,1.625 true 5.76,0.333 5.583,0.333 5.583,0.333 4.49,1.635 true 6.438,0.375 6.25,0.375 6.25,0.375 4.844,1.875 true 2.917,2.75 2.917,3.26 true 3.24,2.76 3.24,3.271 true 3.646,2.313 3.646,3.26 true 3.896,2.313 3.896,3.26 true 4.271,2.313 4.271,3.271 true 0.531,0.292 0.802,0.615 0.271,0.323 10 false *1 1.281,0.281 1.552,0.604 0.271,0.323 10 false *2 2.01,0.271 2.24,0.594 0.229,0.323 10 false *3 2.635,0.292 2.906,0.615 0.271,0.323 10 false *4 4.521,0.24 4.792,0.563 0.271,0.323 10 false *6 5.188,0.24 5.458,0.563 0.271,0.323 10 false *7 5.083,3.271 5.354,3.594 0.271,0.323 10 false *13 2.781,3.281 3.052,3.604 0.271,0.323 10 false *10 3.51,3.292 3.781,3.615 0.271,0.323 10 false *12 4.146,3.292 4.417,3.615 0.271,0.323 10 false *12 5.823,0.229 6.094,0.552 0.271,0.323 10 false *8 6.542,0.281 6.813,0.604 0.271,0.323 10 false *9 3.771,3.292 4.042,3.615 0.271,0.323 10 false *11 3.125,3.292 3.396,3.615 0.271,0.323 10 false *11 3.813,0.229 4.083,0.552 0.271,0.323 10 false *5

Text in Illustration
*1 Input Shaft *2 Reverse Gear
*3 1st Gear *4 2nd Gear
*5 4th Gear *6 3rd Gear
*7 6th Gear *8 5th Gear
*9 Output Shaft *10 Reverse Type Synchromesh Mechanism
*11 Triple-cone Type Synchromesh Mechanism *12 Single-cone Type Synchromesh Mechanism
*13 Counter Shaft - -

Synchromesh Mechanism
Gear 1st, 2nd and 3rd 4th, 5th and 6th Reverse
Synchromesh Mechanism Type Triple-cone Single-cone Reverse



b.

Oil Separator

i.

An oil separator made of aluminum alloy is provided at the bottom of the transmission rear case. This construction prevents the oil sump from being directly mixed by the counter shaft. By combining this with the transmission middle case, which has a tank construction, the oil mixing loss has been reduced.

X101669E03
5.063,2.26 5.063,2.885 true 1.427,2.615 2.052,2.615 true 1.24,2.51 1.469,2.677 0.229,0.167 10 false *1 4.979,2.927 5.208,3.094 0.229,0.167 10 false *2 2.333,0.49 2.563,0.656 0.229,0.167 10 false *a 3.021,0.49 3.25,0.656 0.229,0.167 10 false *b

Text in Illustration
*1 Tank Construction *2 Oil Separator
*a Middle Case Side *b Rear Case Side



c.

Shift and Select Mechanism

i.

The shift and select mechanism has 4 shift forks and a sliding-shaft type shift. The shift detent mechanism that is used is the same as the conventionally used ball and spring detent system. High shifting characteristics have been obtained by providing a mechanism that prevents double gearing, and accidental shifting into reverse gear.

X101670E04
1.969,3.615 2.594,3.615 true 1.531,1.708 2.063,1.708 true 1.531,1.24 1.958,1.24 true 2.625,0.635 3.031,0.635 3.031,0.635 3.031,1.51 true 4.219,0.51 3.271,0.51 3.271,0.51 3.271,2.073 true 4.24,0.813 3.646,0.813 3.646,0.813 3.646,1.844 true 3.552,2.417 3.563,4.469 3.563,4.469 3.094,4.469 true 3.177,3.656 3.188,4.26 3.188,4.26 2.708,4.26 true 4.073,2.552 4.115,4.552 4.115,4.552 4.667,4.552 true 4.604,2.583 4.635,4.271 4.635,4.271 5.094,4.271 true 1.313,1.146 1.51,1.354 0.198,0.208 10 false *1 1.323,1.625 1.594,1.833 0.271,0.208 10 false *2 1.802,3.542 2.073,3.75 0.271,0.208 10 false *6 2.417,0.563 2.688,0.771 0.271,0.208 10 false *3 4.292,0.406 4.563,0.615 0.271,0.208 10 false *4 4.292,0.729 4.563,0.938 0.271,0.208 10 false *5 2.917,4.396 3.188,4.604 0.271,0.208 10 false *8 2.542,4.188 2.813,4.396 0.271,0.208 10 false *7 4.708,4.458 4.979,4.667 0.271,0.208 10 false *10 5.156,4.177 5.427,4.385 0.271,0.208 10 false *9

Text in Illustration
*1 Shift Detent Ball *2 Compression Spring
*3 No. 3 Shift Fork Shaft *4 No. 1 Shift Fork Shaft
*5 No. 2 Shift Fork Shaft *6 No. 4 Shift Fork
*7 No. 1 Shift Fork *8 No. 4 Shift Fork Shaft
*9 No. 3 Shift Fork *10 No. 2 Shift Fork