Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2020.08
NM27T0E _51 Engine / Hybrid System _053610 CRUISE CONTROL _0330905 ROAD SIGN ASSIST SYSTEM CO CONTROL F

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  CONTROL  ROAD SIGN ASSIST CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the RSA system have the following functions.

Components Function

*1: The threshold can be adjusted to 1 of 3 levels through the customization function.

*2: Except models for Australia

*3: Models with navigation system

Forward Recognition Camera
·

Captures road signs.

·

Performs RSA system control based on information of road signs captured by the built-in camera.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Detects object information and sends signals to forward recognition camera.
Combination Meter Assembly - Sends a turn signal command to the forward recognition camera.
Master Warning Light Comes on when there is a malfunction in the RSA system.
Multi-information Display
·

Displays road signs recognized by the forward recognition camera.

·

The RSA system can be turned on and off through the settings tab.


Meter Buzzer Sounds when the speed limit is exceeded*1, a no overtaking notification is displayed*2 or there is an entry prohibition notification*2.
Steering Pad Switch Assembly Meter Control Switch Sends a multi-information operating signal to the forward recognition camera.
Headlight Dimmer Switch Assembly
·

Turn Signal Switch


Sends a turn signal command to the combination meter assembly.
Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera.
Air Conditioning Amplifier Assembly Sends the ambient temperature signal to the forward recognition camera.
ECM Sends the shift position signal to the forward recognition camera.
Airbag Sensor Assembly Detects the yaw rate and sends it to the forward recognition camera.
Radio and Display Receiver Assembly*3 Sends map information from the navigation ECU to the forward recognition camera.
Navigation ECU*3 Sends map information to the radio and receiver assembly.
Central Gateway ECU (Network Gateway ECU) Transmits the signal between the CAN communication buses.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.



FUNCTION


a.

The RSA system recognizes the following traffic signals using the forward recognition camera.

Except Models for Australia
Category Sign Type Example of Recognizable Sign

*: Models with navigation system

Speed Limit Round maximum speed limit/End of speed limit
Y180848

No Overtaking No overtaking/End of no overtaking
Y180849

End of Prohibition
Y180854

Supplemental Signs Road Condition Signs Ramp way
Y180850

Rain
Y180851

Wet
Y189642

Supplemental Signs Road Condition Signs Ice
Y180852

Time
Y235976

Information Signs Related Speed Limit Highway sign (entrance, exit)
Y223984

Motorway sign (entrance, exit)
Y223985

Information Signs Related Speed Limit Built-up area sign (start, end)
Y235943

Y235975

Information Signs Related Speed Limit Home zone sign (start, end)
Y223986

No Entry*
Y188807

Stop
Y223969


Models for Australia
Category Sign Type Example of Recognizable Sign
Speed Limit Round maximum speed limit
Y242210

Supplemental Sign School Zone
Y251539



b.

The RSA system displays the following traffic signals using the forward recognition camera.

Except Models for Australia
Category Display Example Details

*: Models with navigation system

Speed Limit Related
Y180848

·

Informs the driver of the maximum speed limit of the currently driven road.

·

The displayed sign reflects the speed limit on the recognized sign.


Speed Limit Related
Y223984

Informs the driver of highway signs (entrance, exit).
Y223985

Informs the driver of motorway signs (entrance, exit).
Speed Limit Related
Y235943

Y235975

Informs the driver built-up area sign (start, end).
Speed Limit Related
Y223986

Informs the driver home zone sign (start, end).
No Overtaking Related
Y180849

Informs the driver when they are in a no overtaking zone on the currently driven road.
No Entry*
Y188807

Informs the driver that there are vehicle entry restricted sections on the currently driven road.
All Canceled (All restrictions canceled. Return to default road regulations.)
Y180854

Informs the driver when all applicable prohibitions, such as speed limit and no overtaking, have ended.
Stop
Y223969

Informs the driver that there is a stop ahead.
Speed Limit with Supplemental Sign Related Ramp Way
Y180858

Informs the driver of the ramp way direction. However, this item is not displayed when making a lane change without operating the turn signal light.
Rain
Y194214

Informs the driver of the maximum speed limit on the currently driven road when it is raining or the road surface is wet.
Ice
Y188514

Informs the driver of the maximum speed limit on the currently driven road when there is accumulated snow or ice.
Speed Limit with Supplemental Sign Related Time
Y235977

Informs the driver of the time zone speed limit sign on the currently driven road.
Blank
Y188515

The display is blank when the system is unable to recognize a supplemental sign.

Models for Australia
Category Display Example Details
Speed Limit Related
Y242210

·

Informs the driver of the maximum speed limit of the currently driven road.

·

The displayed sign reflects the speed limit on the recognized sign.


Conditional Speed Limit Sign School Zone
Y261442

Informs the driver that the currently driven road is in a school zone and its speed limit changes depending on the time of day.

HINT:

A non-official (sign not meeting Vienna Convention) or a recently introduced traffic sign may not be recognized.



c.

Notification functions are used in the RSA system which invert the colors of displayed signs, flash signs, etc. to notify the driver.

i.

Speed Limit Exceeded Notification

·

While a speed limit sign is displayed, if the actual vehicle speed exceeds the speed limit plus a designated threshold*1, the colors of the displayed sign are inverted and the meter buzzer sounds.*2 For example, if the threshold is set to 5 km/h and the speed limit sign is 60 km/h, the colors of the displayed sign are inverted and the meter buzzer sounds, when the actual vehicle speed exceeds 65 km/h. Furthermore, the system also inverts a speed limit sign with supplemental sign in the same way. However, the system does not invert the colors of the supplemental sign.

HINT:

*1: The threshold can be adjusted to 1 of 3 levels through the customization function.

*2: Customization is required for inverted display and sounding of the meter buzzer.



Notification Method Display Example
Inverted Display
Y180861



ii.

No Overtaking Notification (Except models for Australia)

·

While a no overtaking sign is displayed, if the system detects that the vehicle is attempting to overtake another vehicle, the system flashes the displayed sign and sounds the meter buzzer.*

HINT:

*: Customization is required for blinking display and sounding of the meter buzzer.



Notification Method Display Example
Flashing Display
Y180862



iii.

No-entry Notification (Except models for Australia and Models with Navigation System)

·

While a no entry sign is recognized, if the system detects that the driver is driving on a road where entry is prohibited, based on map information, the system flashes the displayed sign and sounds the meter buzzer.*

HINT:

*: Customization is required for blinking display and sounding of the meter buzzer.



Notification Method Display Example
Flashing Display
Y187317




d.

The RSA system can be turned on or off through the settings tab of the multi-information display.


e.

A customization function is used for the RSA, which allows settings such as the notification method and level for exceeding the speed limit to be changed. Setting changes are made through the customization tab of the multi-information display. Refer to the Repair Manual for details.



SYSTEM CONTROL


a.

RSA Control Pattern 1

i.

After a road sign* is recognized by the forward recognition camera, the sign is displayed on the multi-information display.

*: Except for stop sign



ii.

While a sign is displayed on the multi-information display, if no sign has been recognized within a specified distance, display of the current sign is turned off.

Y266764E01
2.292,1.354 2,0.333 2,0.333 1.75,0.333 true 3.635,0.708 5.229,1.063 1.594,0.354 10 false Specified Distance Driven 1.604,2.01 3.115,2.354 1.51,0.344 10 false Road Sign Recognized 1.094,2.688 2.688,3.042 1.594,0.354 10 false : Sign display off 1.104,3.208 2.698,3.563 1.594,0.354 10 false : Sign display on 1.052,0.24 2.646,0.594 1.594,0.354 10 false Road Sign 1.031,1 1.958,1.281 0.927,0.281 10 false Meter Display


iii.

After a stop sign is recognized by the forward recognition camera, the sign is displayed on the multi-information display.


iv.

While a sign is displayed on the multi-information display, if the vehicle passes the sign, display of the current sign is turned off.

Y246058E05
4.354,1.458 4.979,0.385 4.979,0.385 5.219,0.385 true 1.552,2.01 3,2.323 1.448,0.313 10 false Road Sign Recognized 0.969,2.635 2.063,2.99 1.094,0.354 10 false : Sign display off 0.969,3.219 2.063,3.573 1.094,0.354 10 false : Sign display on 1.031,1.042 1.958,1.354 0.927,0.313 10 false Meter Display 5.292,0.302 6.219,0.615 0.927,0.313 10 false Road Sign 4.292,2.031 5.5,2.563 1.208,0.531 10 false Road Sign Passing Recognized



b.

RSA Control Pattern 2

i.

When the ignition switch is turned off while a speed limit sign is displayed on the multi-information display, the same sign is displayed when the ignition switch is turned to ON again.

Y233218E06
4.719,0.438 7.156,1.083 2.438,0.646 10 false Ignition Switch is Turned to ON 1.125,2.969 5.104,3.167 3.979,0.198 10 false : Sign display on 0.896,0.448 3.104,1.104 2.208,0.656 10 false Ignition Switch is Turned Off



c.

RSA Control Pattern 3

i.

While a sign is displayed on the multi-information display, the sign is turned off when turning left or right onto a new road.

Y266765E01
5.708,4.979 7.115,5.469 1.406,0.49 10 false Road Sign Recognized 0.833,4.281 2.292,4.531 1.458,0.25 10 false : Sign display off 0.844,5.042 2.302,5.292 1.458,0.25 10 false : Sign display on 2.583,3.594 3.646,3.896 1.063,0.302 10 false Meter Display 1.406,2.125 2.813,2.771 1.406,0.646 10 true Driving Road Changed after Left Turn




DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). For details, refer to the Repair Manual.