FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*: Models with pre-collision system |
||
| Absorber Control Actuator | Changes the damping force of the shock absorbers. | |
| Shock Absorber Assembly | Changes the oil flow passage by rotating the rotary valve, and switches the damping force. | |
| Front and Rear Acceleration Sensor | Detects the vertical acceleration rate of the body. | |
| Steering Angle Sensor | Detects the steering direction and the angle of the steering wheel. | |
| Drive Mode Select | Switches the driving mode. | |
| Center Airbag Sensor Assembly | Deceleration Sensor | Detects the vehicle's longitudinal and lateral acceleration and deceleration. |
| Suspension Control ECU
(with Built-in Front Acceleration Sensor LH) |
·
Estimates the condition of the vehicle in accordance with the signals provided by the sensors and switches, and outputs control signals to the absorber control actuators. ·
Detects the vertical acceleration rate of the body. |
|
| Skid Control ECU | ·
Sends the vehicle speed signal to the suspension control ECU. ·
Sends the brake pedal depressing signal to the suspension control ECU. |
|
| 4WD Control ECU | Sends the transfer drive mode to the suspension control ECU. | |
| Forward Recognition Camera* | Makes a request for damping force control to the suspension control ECU. | |
| ECM | Sends the driving mode signal and drive torque signal to the suspension control ECU. | |
SYSTEM CONTROL
The AVS performs the following controls:
| Control | Outline |
|---|---|
|
*: Models with pre-collision system |
|
| Repercussion Control (Non-linear H∞ Control) | Smoothly changes the damping force to a target value in accordance with the changes in the road surface or driving conditions. In this way, excellent ride comfort is achieved while ensuring a high level of vibration damping performance. |
| Roughness Sensing Control | When the road surface condition does not require a damping force, this function controls the shock absorbers so that their damping force will not increase. |
| Unsprung Damping Control | If unsprung resonance is detected, this function controls so that the damping force will not decrease below a certain level, in order to reduce the unsprung resonance. |
| Roll Posture Control | Regulates the damping force to reduce the phase difference between the vehicle roll and pitch angles during steering, providing smooth superior maneuverability. |
| Anti-dive Control | During braking, this function makes the damping force firmer to restrain the body dive, ensuring excellent stability and controllability. |
| Anti-squat Control | During acceleration, this function makes the damping force firmer to minimize the changes in the vehicle body posture. |
| Vehicle Speed Sensing Control | This function varies the variable range of the damping force in accordance with the vehicle speed in order to achieve a soft and comfortable ride and a stable driving condition. The damping force is controlled at a softer variable range at low speeds, and at a firmer variable range at high speeds. |
| Damping Mode Selection | The drive mode select enables the driver to select a desired damping force from the 3 modes. |
| Pre-collision System Operation Control* | Switches damping force to the hard side in accordance with damping force control request signals from the forward recognition camera, and suppresses dive during braking. |
| L4 Range Control | The suspension control ECU controls damping force to a level that is optimal for driving on rough roads in the low speed range and for normal driving in the intermediate speed range, when the transfer drive mode is in L4F or L4L. This ensures ride comfort and driveability in off-road driving. Also, repercussion control (H∞ Control) is used to reduce swing-back due to rough roads. Thus, driving burden is reduced by stabilizing the driver's eye level and superior drive performance is achieved by ensuring road contact performance of the tires. |
Repercussion Control (Non-linear H∞ Control)
In accordance with the acceleration sensor signal, the suspension control ECU detects vehicle vibrations (in the heave, roll and pitch directions) and controls the damping force of each of the 4 wheels using the non-linear H∞ control logic. Therefore, vehicle repercussion is naturally and smoothly controlled, ensuring riding comfort.
Damping Mode Selection
The drive mode select enables the driver to select a desired damping force from the 3 modes.
| Drive Mode Select | Damping Force Control Mode | Outline |
|---|---|---|
| NORMAL | NORMAL | Achieves a good balance of high-level steering response, flat feeling, sense of stability and riding comfort. |
| ECO | ||
| SPORT S | ||
| SPORT S+ | SPORT | Mainly uses the hard damping force range to further emphasize steering response, flat feeling and stability, achieving sporty driving. |
| COMFORT | COMFORT | Mainly uses the soft damping force range to achieve a more comfortable ride. |
The suspension control ECU receives signals from the sensors and switches to control the absorber control actuators. It uses these signals to optimally control the damping force in accordance with the driving conditions and road conditions.
CONSTRUCTION
Shock Absorber Assembly and Absorber Control Actuator
The front and rear shock absorber assembly is used to optimize damping force, achieving superior stability and riding comfort. In addition, the structure of the oil seal has been optimized, ensuring superior reliability.
The front shock absorber assembly is equipped with an external actuator.
The rear shock absorber assembly is equipped with an internal actuator.
The piston rod is equipped with a rotary valve, a soft damping force valve and a hard damping force valve.
| *1 | Front Absorber Control Actuator | *2 | Actuator Bracket |
| *3 | Front Shock Absorber Assembly | *4 | Soft Damping Force Valve |
| *5 | Hard Damping Force Valve | *6 | Rotary Valve |
| *1 | Rear Shock Absorber Assembly
- Absorber Control Actuator |
*2 | Soft Damping Force Valve |
| *3 | Hard Damping Force Valve | *4 | Rotary Valve |
An absorber control actuator changes the damping force in accordance with the signals received from the suspension control ECU.
A 16-step step motor turns the rotary valve in the shock absorber assembly to vary the opening of the oil passage. This enables the damping force to be changed smoothly.
Front Acceleration Sensor
The front acceleration sensors detect the vertical movement of the body.
The front acceleration sensors are placed on the right and left caul sides. The acceleration sensors independently detect the vertical acceleration rate.
FAIL-SAFE
If a malfunction occurs in the AVS, the suspension control ECU prohibits damping force control.
DIAGNOSIS
The suspension control ECU will also store a Diagnostic Trouble Code (DTC). The DTC can be accessed through the use of a Global TechStream (GTS). For details, refer to the Repair Manual.