Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › from 2021.06
NM27T0E _51 Engine / Hybrid System _053589 1GD-FTV EMISSION CONTROL _0260114 EMISSION CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

1GD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the EGR system*1 are as follows:

*1: Models with EGR system

*2: Models with EGR cooler

Component Function
ECM Controls the EGR system based on signals from each sensor.
Electric EGR Control Valve Assembly Actuated by the ECM, this valve controls the flow rate of EGR gas.
EGR Valve Position Sensor (Built into Electric EGR Control Valve Assembly) Detects the EGR valve position.
Diesel Throttle Valve Actuated by the ECM, this valve controls the flow rate of intake air.
No. 1 EGR Cooler*2 Cools EGR gas.
No. 2 EGR Valve Assembly*2 Switches the flow passage of EGR gas in 2 stages.


b.

The main components of the catalyst support control*1 are as follows:

*1: Models with catalyst support control

*2: Models without UREA SCR system

*3: Models with UREA SCR system

*4: Models with particulate matter sensor

Component Function
ECM Controls the catalyst support control based on signals from each sensor.
Exhaust Gas Temperature Sensor Detects the exhaust gas temperature.
No. 2 Exhaust Gas Temperature Sensor
No. 3 Exhaust Gas Temperature Sensor
Differential Pressure Sensor
·

Monitors the differential pressure before and after the DPF.

·

Compares this data with the PM accumulation amount calculated by the ECM. If there is a large deviation in the comparison result, the ECM corrects the PM accumulation amount.


Exhaust Fuel Addition Injector Assembly Injects fuel into the exhaust manifold.
Air Fuel Ratio Sensor*2 Detects the oxygen concentration in exhaust gas.
NOx Sensor (Nitrogen Oxides Sensor) (Sensor 1)*3 Detects the oxygen concentration in exhaust gas.
Particulate Matter Sensor*4 Detects the state of DPF.


c.

The main components of the UREA SCR system*1 are as follows:

*1: Models with UREA SCR system

*2: Models with particulate matter sensor

Component Function
ECM Receives the signals from No. 4 Exhaust gas temperature sensor and NOx sensor (nitrogen oxides sensor) and sends the signals to UREA pump control ECU.
UREA Pump Control ECU Controls the UREA SCR system based on signals from each sensor.
No. 4 Exhaust Gas Temperature Sensor Detects the exhaust gas temperature.
NOx Sensor (Nitrogen Oxides Sensor) (Sensor 1)
·

Detects the oxygen concentration in exhaust gas.

·

Detects the concentration of NOx in the exhaust gas.


NOx Sensor (Nitrogen Oxides Sensor) (Sensor 2) Detects the concentration of NOx in the exhaust gas.
Particulate Matter Sensor*2 Detects the state of DPF.



FUNCTION


a.

EGR System (Models with EGR System )

i.

This system is designed to help reduce and control NOx formation due to a reduction of peak temperature in the engine combustion chamber, which is accomplished by the introduction of an amount of inert gas into the intake manifold.



b.

Catalyst Support Control (Models with Catalyst Support Control)

i.

When an extremely large amount of PM is accumulated in the DPF, the back pressure of the engine increases and the PM is combusted at once, potentially damaging the filter. In order to prevent that, it is necessary to forcibly combust the accumulated PM. Therefore, the accumulated PM is combusted by increasing the temperature of the filter.


ii.

If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message is displayed on the multi-information display*1 or the DPF warning light*2 illuminates or blinks to notify the driver.

*1: Models with multi-information display

*2: Models without multi-information display




c.

UREA SCR System (Models with UREA SCR System)

i.

Urea solution is injected by the urea injector set to purify NOx in the exhaust gas.




SYSTEM CONTROL


a.

EGR System (Models with EGR System)

i.

The EGR system carries out the following controls:

1.

The ECM actuates the electric EGR control valve assembly, which regulates the volume of EGR gas recirculation, in accordance with the engine condition.

2.

The ECM switches the bypass passage of the No. 1 EGR cooler via the No. 2 EGR valve assembly in 2 stages in order to optimize the temperature of the EGR gas and clean exhaust gases.*

*: Models with EGR cooler





b.

Catalyst Support Control (Models with Catalyst Support Control)

i.

In order to regenerate the DPF, the temperature of the DPF is increased to combust the accumulated PM in the DPF, expelling it as CO2 and H2O.


ii.

If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message and the amount of accumulated PM (in 10 levels) are simultaneously displayed on the multi-information display to notify the driver.*1


iii.

The ECM monitors the engine condition and calculates the total amount of accumulated PM. In addition, the ECM calculates the amount of combusted PM according to the engine speed, fuel injection volume and the injection volume of the exhaust fuel addition injector assembly. The amount of accumulated PM in the DPF is calculated based on the calculated total amount of accumulated PM and the amount of combusted PM. The ECM urges the driver to perform PM automatic or manual regeneration according to the level of accumulated PM.


iv.

When automatic or manual regeneration is performed, the injection of the exhaust fuel addition injector assembly and the engine combustion condition are controlled, increasing the temperature of the DPF. As a result, the temperature of the DPF becomes approximately 600°C to 700°C and PM is combusted.


v.

When the vehicle is continuously driven with a high exhaust temperature such as at high speeds, the temperature of the DPF is sufficiently increased and PM is spontaneously combusted. At this time, no special control such as exhaust fuel addition injector assembly control, etc. is performed.


vi.

When the vehicle is continuously driven while the temperature of the DPF is not high enough for PM combustion such as when driving for a short distance or driving for a short time, catalyst performance is decreased. As a result, PM is accumulated in the DPF. When the amount of accumulated PM exceeds the threshold (for automatic regeneration), the ECM performs automatic regeneration until the amount of PM reaches zero.


vii.

If the vehicle continues to be driven for a short distance even after automatic regeneration is performed, more PM is accumulated. When the amount of accumulated PM exceeds the threshold (for manual regeneration), a message and the amount of accumulated PM are simultaneously displayed on the multi-information display*1 or the DPF warning light*2 illuminates or blinks to urge the driver to perform manual regeneration.

*1: Models with multi-information display

*2: Models without multi-information display



viii.

Automatic Regeneration

When automatic regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition, increasing the temperature of the DPF to combust the PM. Idle up is performed while the vehicle is stopped.

HINT:

The end of automatic regeneration is calculated by the ECM according to the amount of accumulated PM.




ix.

Manual Regeneration

1.

The following methods are used to perform manual regeneration. For details of manual regeneration operation, refer to the Repair Manual.

(a)

Driving Method

Drive for 20 to 30 minutes at 65 km/h or higher to perform manual regeneration.


(b)

Global TechStream (GTS) Operation Method

Stop the vehicle and operate the Global TechStream (GTS) to perform manual regeneration.



2.

When manual regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition and performs idle up, increasing the temperature of the DPF to combust the PM.

HINT:

The end of manual regeneration is calculated by the ECM according to the amount of accumulated PM.




x.

Fail-safe

If manual regeneration is performed when the amount of accumulated PM is beyond the threshold, the DPF may get damaged. Therefore, when the amount of accumulated PM exceeds the threshold (for the fail-safe function), the injection volume is controlled to a minimum level to cancel regeneration control. As a result, manual regeneration cannot be performed properly. At the same time, the MIL illuminates and a message is displayed on the multi-information display*1 or the DPF warning*2 light blinks to notify the driver of a malfunction.

Relationship between MIL, Message on Multi-information Display*1, DPF Warning Light*2 and Regeneration Control (Conceptual Diagram)
W138767E01
2.313,3.688 2.542,3.688 2.542,3.688 2.615,3.073 true 0.531,0.052 2.219,0.344 1.688,0.292 10 false : Automatic regeneration 3.688,0.052 5.375,0.344 1.688,0.292 10 false : Manual regeneration 0.052,1.677 0.927,2.573 0.875,0.896 10 false PM Accumulation 0.958,1.042 2.448,1.344 1.49,0.302 10 false Threshold (for Fail-safe) 1.125,2.146 2.469,2.677 1.344,0.531 10 false Threshold (for Manual Regeneration) 1,2.719 2.573,3.323 1.573,0.604 10 false Threshold (for Automatic Regeneration) 2.625,0.781 4.458,1.115 1.833,0.333 10 false Fail-safe Range 2.573,1.177 4.406,1.51 1.833,0.333 10 false Manual Regeneration Range 2.552,2.281 4.021,2.771 1.469,0.49 10 false Automatic Regeneration Range 0.667,3.583 2.26,3.896 1.594,0.313 10 false Normal Operation Range 6.635,3.01 6.792,3.208 0.156,0.198 10 false A 6.635,2.458 6.792,2.656 0.156,0.198 10 false B 6.635,1.885 6.792,2.083 0.156,0.198 10 false C 6.635,1.302 6.792,1.5 0.156,0.198 10 false D 6.635,0.906 6.792,1.104 0.156,0.198 10 false E 3.99,3.396 5.427,3.927 1.438,0.531 10 false Traveled Distance

Text in Illustration MIL DPF Warning Light*2 Massage on Multi-information Display*1
A - - -
B - - -
C - Illuminate DPF FULL SEE OWNER'S MANUAL
D - Blink DPF FULL VISIT YOUR DEALER
E Illuminate Blink DPF FULL VISIT YOUR DEALER

*1: Models with multi-information display

*2: Models without multi-information display



W138315C01
3.792,1.583 4.792,1.042 true 3.198,0.635 3.51,0.792 0.313,0.156 10 false *1 3.906,0.646 4.396,0.854 0.49,0.208 10 false *2 (*A) 4.854,0.958 5.438,1.177 0.583,0.219 10 false *3 (*B)
*A Models without Multi-information Display *B Models with Multi-information Display
*1 MIL *2 DPF Warning Light
*3 Multi-information Display - -




c.

UREA SCR System (Models with UREA SCR System)

i.

A UREA SCR system is used to purify NOx in the exhaust gas. The urea SCR system injects urea solution into the exhaust gas to generate ammonia. The generated ammonia produces a chemical reaction with the NOx in the exhaust gas on the SCR catalyst, breaking it down into nitrogen and water, thereby purifying the exhaust gas.


ii.

The UREA SCR system is composed of a UREA pump control ECU, urea tank sub-assembly, urea injector set, urea pump, No.4 exhaust gas temperature sensor and NOx sensor (nitrogen oxides sensor).


iii.

In the UREA SCR system, the UREA pump control ECU controls the urea injector set and urea pump based on various signals.


iv.

The amount of NOx in the exhaust gas increases as the engine load increases. This system injects urea solution according to the engine load in order to maintain the amount of NOx at a certain level or less.

W142688E03
2.49,0.938 2.896,0.469 2.896,0.469 3.156,0.469 true 2.063,1.875 1.792,2.125 1.792,2.125 1.531,2.125 true 4.469,1.823 4.417,0.885 4.417,0.885 3.354,1.833 true 5.667,0.313 5.49,0.313 5.49,0.313 5.104,1.813 true 5.979,1.208 5.802,1.208 5.802,1.208 5.625,1.854 true 2.292,1.406 1.75,1 1.75,1 1.552,1 true 3.208,0.406 5.021,0.656 1.813,0.25 10 false Diesel Particulate Filter (DPF) 0.396,2.052 1.604,2.229 1.208,0.177 10 false UREA Injector Set 0.781,0.927 1.583,1.115 0.802,0.188 10 false Exhaust Gas 6.021,1.135 7.01,1.323 0.99,0.188 10 false Exhaust Gas 4.448,0.74 5.427,0.938 0.979,0.198 10 false SCR Catalyst 0.281,2.667 1.604,2.865 1.323,0.198 10 false Before SCR Catalyst 4.052,2.688 5.26,2.885 1.208,0.198 10 false After SCR Catalyst 0.344,3.76 0.875,4.073 0.531,0.313 10 false NOx Amount 1.396,4.698 2.208,4.896 0.813,0.198 10 false Engine Load 5.833,2.729 6.896,3.292 1.063,0.563 10 false : Urea Solution Addition Volume 5.698,0.25 7.115,0.469 1.417,0.219 10 false Ammonia Slip Catalyst 4.25,3.729 4.781,4.042 0.531,0.313 10 false NOx Amount 5.333,4.698 6.146,4.896 0.813,0.198 10 false Engine Load

HINT:

When the SCR catalyst temperature reaches a certain temperature or more, such as when high-load driving continues for a long period of time or DPF regeneration is in progress, the amount of urea solution that is injected is further increased.



v.

The amount of urea solution that is consumed changes depending on the driving conditions and environment. During high-load driving, the amount of urea solution that is consumed increases and the driving range decreases. Inversely, during low-load driving, the amount of urea solution that is consumed decreases and the driving range increases.

W142689E04
3.01,0.229 4.323,0.458 1.313,0.229 10 false Possible driving range 0.344,0.813 0.885,0.99 0.542,0.177 10 false Short*1 6.354,0.833 6.708,1.042 0.354,0.208 10 false Long 0.917,1.479 2,1.677 1.083,0.198 10 false [High-load driving] 3.156,1.479 4.115,1.677 0.958,0.198 10 false [Normal driving] 5.271,1.469 6.396,1.688 1.125,0.219 10 false [Low-load driving] 0.156,1.896 2.573,2.24 2.417,0.344 10 false - When your vehicle is towing a trailer 0.156,2.396 1.938,2.938 1.781,0.542 10 false - When firmly depressing the accelerator pedal 4.625,1.917 6.917,2.146 2.292,0.229 10 false - When driving short distances 4.625,2.542 6.917,2.771 2.292,0.229 10 false - When in traffic congestion 3.344,1.052 4.26,1.25 0.917,0.198 10 false 8000 km*2 5.438,1.052 6.354,1.25 0.917,0.198 10 false 57000 km*2 1.229,1.052 2.146,1.25 0.917,0.198 10 false 2400 km*2 0.135,4.219 7.073,4.865 6.938,0.646 10 false *1: The amount of urea solution that is consumed increases when driving at high elevations, when the ambient temperature is low and when the exhaust gas purification device is operating. 0.115,5.135 7,5.396 6.885,0.26 10 false *2: The driving range is for reference only. 0.146,3.219 2.438,3.448 2.292,0.229 10 false - When driving on long uphill slopes


vi.

Remaining Urea Solution Display

1.

The remaining amount of urea solution is displayed on the multi-information display, based on the urea solution level in the urea tank sub-assembly measured by the urea solution level sensor

W148702C01
6.469,0.542 6.229,0.542 6.229,0.542 5.75,1.406 false 6.521,0.458 6.833,0.615 0.313,0.156 10 false *1 0.594,0.406 0.906,0.563 0.313,0.156 10 false *a
*1 Multi-information Display - -
*a Remaining Urea Solution Display - -




vii.

Urea Solution Quality Display

1.

A message is displayed on the multi-information display when the urea solution concentration detected by the urea solution concentration sensor drops below the specified value.





CONSTRUCTION


a.

Oxidation Catalyst

i.

An oxidation catalyst is used to purify HC and CO in the exhaust gas.

Models with Catalyst Support Control
W127891E02
2.615,1.896 1.729,1.385 true 4.688,2.635 4.104,2.156 true 1.583,1.281 1.823,1.552 0.24,0.271 10 false *1 4.708,2.615 4.948,2.885 0.24,0.271 10 false *2

Text in Illustration
*1 Exhaust Manifold Converter Sub-assembly *2 Oxidation Catalyst
V100135

Exhaust Gas - -

Models without Catalyst Support Control
W146824E01
4.625,2.49 4.042,2.01 true 4.667,2.49 4.906,2.76 0.24,0.271 10 false *1

Text in Illustration
*1 Oxidation Catalyst - -
V100135

Exhaust Gas - -



b.

DPF

i.

A DPF catalyst is used to collect and purify PM.

W127971E02
2.583,1.917 1.698,1.406 true 4.219,2.833 3.635,2.354 true 1.521,1.302 1.76,1.573 0.24,0.271 10 false *1 4.229,2.833 4.469,3.104 0.24,0.271 10 false *2

Text in Illustration
*1 Exhaust Manifold Converter Sub-assembly *2 DPF
V100135

Exhaust Gas - -



c.

SCR Catalyst

i.

3 SCR catalysts are provided in the front pipe area to improve NOx purification performance.

W127892C02
3.052,3.073 3.333,2.417 true 5.229,1.927 5.49,2.875 5.49,2.875 4.729,2.021 true 5.49,2.927 5.885,3.24 0.396,0.313 10 false *1 2.948,3.115 3.302,3.417 0.354,0.302 10 false *1
*1 SCR Catalyst - -
V100135

Exhaust Gas - -




d.

UREA Pump

i.

A urea pump integrated with the urea pump control ECU is used. It is placed on the lower urea tank sub-assembly.

W148714E01
0.49,0.74 0.729,0.74 0.729,0.74 1.51,2 true 5,4.156 4.479,4.156 true 3.052,4.135 2.833,4.135 2.833,4.135 2.177,2.677 true 4.406,0.708 4.583,0.708 4.583,0.708 5.073,1.323 true 4.323,1.354 4.5,1.354 4.5,1.354 4.781,1.76 true 4.313,1.958 4.49,1.958 4.49,1.958 5.063,2.271 true 6.042,2.875 5.844,2.875 5.844,2.875 5.427,3.323 true 0.323,0.667 0.594,0.979 0.271,0.313 10 false *1 3.104,4.052 3.375,4.365 0.271,0.313 10 false *2 4.24,0.646 4.51,0.958 0.271,0.313 10 false *3 4.156,1.292 4.427,1.604 0.271,0.313 10 false *4 4.146,1.885 4.417,2.198 0.271,0.313 10 false *5 6.083,2.792 6.354,3.104 0.271,0.313 10 false *6 4.302,4.083 4.573,4.396 0.271,0.313 10 false *7

Text in Illustration
*1 Urea Solution Level Sensor *2 Urea Solution Concentration Sensor
*3 Heater *4 Filter
*5 Pump Motor *6 Pressure Sensor
*7 Urea Pump Control ECU - -


ii.

The urea pump has the following functions:

Function Outline
Pump Function While performing feedback control according to the pressure sensor inside the urea pump, the pump raises the pressure to approximately 500 kPa, sending urea solution to the urea injector set.
Heating Function The heater inside the urea pump is operated to thaw the urea solution so that exhaust gas can be purified even when the ambient temperature is low and the urea solution freezes. The heater turns on and off according to the urea solution temperature sensor inside the urea pump.
Filter Function Foreign matter that enters the urea tank sub-assembly is collected by the filter inside the urea pump, preventing foreign matter from getting jammed in the urea pump and urea injector set.
Level Gauge Function The fluid level position is detected by the float sensor inside the urea pump in order to detect the remaining quantity of urea solution inside the urea tank sub-assembly.
Concentration Detection Function The concentration of urea solution in the urea tank sub-assembly is detected by the urea solution concentration sensor in the urea pump.



e.

EGR Valve

i.

A DC motor type electric EGR control valve assembly is used. The placement of the electric EGR control valve assembly at the intersection between the intake passage and EGR bypass facilitates the uniform distribution of EGR gas and intake air.


ii.

An EGR valve position sensor is provided in the electric EGR control valve assembly. This sensor enables EGR valve control at a higher level of precision by detecting the opening angle of the EGR valve.

W127893E02
3.219,1.667 1.313,1.063 true 1.156,0.948 1.635,1.25 0.479,0.302 10 false *1

Text in Illustration
*1 Electric EGR Control Valve Assembly - -



f.

EGR Pipe and EGR Valve

i.

Models with EGR Cooler

1.

A water-cooled type No. 1 EGR cooler is used between the exhaust manifold and electric EGR control valve assembly. In the water-cooled type No. 1 EGR cooler, engine coolant flows through eight-layered gas passage to cool down the EGR gas.

2.

The No. 2 EGR valve assembly is used. The EGR gas passage is switched in 2 stages by the No. 2 EGR valve assembly to optimize the temperature of the EGR gas.

W146826E01
2.24,0.302 2.865,1.094 true 5.01,2.146 5.844,2.469 true 4.375,1.01 4.458,1.344 true 4.031,1.385 4.385,1.896 true 3.74,1.573 4.271,1.854 true 4.177,2.99 4.677,3.302 true 3.927,3.063 4.406,3.448 true 3.573,3.156 3.24,3.406 true 3.021,2.573 2.5,2.677 true 2.063,0.146 2.469,0.448 0.406,0.302 10 false *1 2.313,2.615 2.719,2.917 0.406,0.302 10 false *2 3.083,3.385 3.49,3.688 0.406,0.302 10 false *3 4.719,3.281 5.125,3.583 0.406,0.302 10 false *4 3.583,1.438 3.99,1.74 0.406,0.302 10 false *5 3.906,1.25 4.313,1.552 0.406,0.302 10 false *c 4.302,0.844 4.708,1.146 0.406,0.302 10 false *6 5.906,2.406 6.313,2.708 0.406,0.302 10 false *b 4.448,3.448 4.719,3.677 0.271,0.229 10 false *a

Text in Illustration
*1 Exhaust Manifold *2 No. 1 EGR Cooler
*3 Diesel Throttle Body Assembly *4 Intake Manifold
*5 No. 2 EGR Valve Assembly *6 Electric EGR Control Valve Assembly
*a Intake Air *b EGR Gas
*c EGR Gas (through Bypass Passage) - -



ii.

Models without EGR Cooler

1.

EGR gas is sent to the intake manifold through the No. 1 EGR pipe, EGR valve adapter, EGR valve and No. 2 EGR pipe.

W146825E01
2.24,0.302 2.865,1.094 true 5.01,2.146 5.844,2.469 true 4.375,1.01 4.458,1.344 true 4.177,2.99 4.677,3.302 true 3.927,3.063 4.406,3.448 true 3.573,3.156 3.24,3.406 true 3.438,2.25 2.563,2.208 true 2.063,0.146 2.469,0.448 0.406,0.302 10 false *1 2.344,2.135 2.75,2.438 0.406,0.302 10 false *2 3.083,3.385 3.49,3.688 0.406,0.302 10 false *3 4.719,3.281 5.125,3.583 0.406,0.302 10 false *4 4.302,0.833 4.708,1.135 0.406,0.302 10 false *5 5.906,2.406 6.313,2.708 0.406,0.302 10 false *b 4.448,3.448 4.719,3.677 0.271,0.229 10 false *a

Text in Illustration
*1 Exhaust Manifold *2 EGR Valve Adapter
*3 Diesel Throttle Body Assembly *4 Intake Manifold
*5 No. 2 EGR Valve Assembly - -
*a Intake Air *b EGR Gas




g.

Exhaust Fuel Addition Injector

i.

The exhaust fuel addition injector assembly is installed on the exhaust manifold. Fuel is supplied by the injector to maintain the temperature of the catalyst, removing PM.


ii.

An exhaust fuel addition injector assembly consists of a needle valve body, a needle valve, and a solenoid valve.

W127895E02
3.448,1.24 2.688,1.24 true 3.583,1.823 2.688,1.823 true 3.531,2.167 2.688,2.167 true 2.531,1.156 2.792,1.365 0.26,0.208 10 false *1 2.521,1.74 2.781,1.948 0.26,0.208 10 false *2 2.531,2.094 2.792,2.302 0.26,0.208 10 false *3

Text in Illustration
*1 Solenoid Valve *2 Needle Valve
*3 Needle Valve Body - -



h.

Differential Pressure Sensor

i.

The differential pressure sensor measures the pressure differences between before and after the DPF with PM in order to detect clogging.


ii.

The sensor is mounted on the cylinder head. The DPF and the sensor are connected with pipes and hoses.

W127896E01
1.396,0.729 1.396,0.313 1.396,0.313 1.813,0.313 true 1.875,0.208 3.604,0.625 1.729,0.417 10 false Differential Pressure Sensor 3.927,1.24 4.438,2.021 0.51,0.781 10 false Output Voltage 6.198,2.219 6.677,2.51 0.479,0.292 10 false (kPa) 4.75,2.229 5.99,2.594 1.24,0.365 10 false Differential Pressure 4.208,0.573 4.688,0.865 0.479,0.292 10 false (V)



i.

Exhaust Gas Temperature Sensor

i.

An exhaust gas temperature sensor, which is a thermistor type, is installed before the oxidation catalyst, before the DPF, after the DPF and after the SCR catalyst*, in order to detect the temperature of the exhaust gas.

*: Models compliant with EURO 6-Step 2 emission regulation


W127897E02
2.802,0.583 3.531,0.75 true 2.646,0.469 2.958,0.771 0.313,0.302 10 false *1

Text in Illustration
*1 Exhaust Gas Temperature Sensor - -



j.

Air Fuel Ratio Sensor

i.

An air fuel ratio sensor is used to optimize the combustion and the catalyst conditions. The structure of the sensor is layered to promote early activation, achieving air fuel ratio feedback control in the early stages of engine start.


ii.

The air fuel ratio sensor is installed after the DPF catalyst.

W127898E02
2.729,1.042 3.448,1.396 true 2.563,0.917 2.927,1.219 0.365,0.302 10 false *1

Text in Illustration
*1 Air Fuel Ratio Sensor - -



k.

NOx Sensor

i.

An NOx sensor (nitrogen oxides sensor) is installed in exhaust converter and center exhaust pipe assembly, in order to detects the concentration of NOx in the exhaust gas.

W137679C01
3.583,1.458 4.75,1.458 true 4.844,1.406 5.24,1.677 0.396,0.271 10 false *1
*1 NOx Sensor (Nitrogen Oxides Sensor) - -




l.

Particulate Matter Sensor

i.

A particulate matter sensor has been positioned in the center exhaust pipe to detect the DPF condition.


ii.

The particulate matter sensor is composed of the sensor unit and SCU (sensor control circuit).


iii.

The sensor output consists of changes in the electrical current that are detected by the sensor unit, converted from analog signals to digital signals by the SCU (sensor control circuit) and sent as digital data to the ECM.


iv.

The SCU heats the heater built into the sensor to maintain the particulate matter sensor at a constant temperature.

W139762E02
3.771,1.063 3.521,0.5 3.521,0.5 3.667,0.5 true 2.26,2.073 2.427,2.073 2.427,2.073 2.74,1.198 true 0.99,0.99 1.521,1.281 0.531,0.292 10 false ECM 2.031,0.698 2.979,0.938 0.948,0.24 10 false Digital Signals 0.646,1.979 2.313,2.219 1.667,0.24 10 false CAN Communication Line 3.26,1.865 4.958,2.125 1.698,0.26 10 false Particulate Matter Sensor 5.51,0.854 6.458,1.115 0.948,0.26 10 false Analog Signals 5.656,2.51 6.521,2.771 0.865,0.26 10 false Sensor Unit 3.708,0.427 5.5,0.76 1.792,0.333 10 false SCU (Sensor Control Circuit)