Home › General › SPECIFICATIONS › 1GR-FE ENGINE CONTROL › 2015.06–2017.08
RM27T0E _V1 General _053654 SPECIFICATIONS _0260351 1GR-FE ENGINE CONTROL F

SPECIFICATIONS  1GR-FE ENGINE CONTROL  SERVICE DATA  


Camshaft Timing Oil Control Valve:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω


Crankshaft Position Sensor:
Tester Connection Condition Specified Condition
1 - 2 Cold 1630 to 2740 Ω
Hot 2065 to 3225 Ω


Engine Coolant Temperature Sensor:
Tester Connection Condition Specified Condition
1 - 2 Approx. 20°C (68°F) 2.32 to 2.59 kΩ
Approx. 80°C (176°F) 0.310 to 0.326 kΩ


Throttle Body:
Tester Connection Condition Specified Condition
2 (M+) - 1 (M-) 20°C (68°F) 0.3 to 100 Ω


Knock Sensor:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 120 to 280 kΩ


Accelerator Pedal:
Accelerator Pedal Operation Accelerator Position No. 1 Accelerator Position No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 5.3 V


Air Fuel Ratio Sensor (for Bank 1):
Tester Connection Condition Specified Condition
1 (HA1A) - 2 (+B) 20°C (68°F) 1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher


Air Fuel Ratio Sensor (for Bank 2):
Tester Connection Condition Specified Condition
1 (HA2A) - 2 (+B) 20°C (68°F) 1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-) Always 10 kΩ or higher


Heated Oxygen Sensor (for Bank 1):
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher


Heated Oxygen Sensor (for Bank 2):
Tester Connection Condition Specified Condition
1 (HT2B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT2B) - 4 (E2) Always 10 kΩ or higher


Circuit Opening Relay:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


No. 1 Integration Relay (IG2):
Tester Connection Condition Specified Condition
IG2 fuse Always Below 1 Ω
1C-1 - 1A-4 Battery voltage not applied to terminals 1A- 1 and 1A-3 10 kΩ or higher
Battery voltage applied to terminals 1A-1 and 1A-3 Below 1 Ω


No. 1 Integration Relay (EFI):
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω
1C-1 - 1B-4 Battery voltage not applied to terminals 1B- 2 and 1B-3 10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω


No. 1 Integration Relay (A/F):
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω
1C-1 - 1B-8 Battery voltage not applied to terminals 1B- 4 and 1B-7 10 kΩ or higher
Battery voltage applied to terminals 1B-4 and 1B-7 Below 1 Ω


Air Pump Heater Relay:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


Air Injection VSV Relay (AI-VSV):
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


Main Body ECU (Driver Side Junction Block) for ACC Relay:
Tester Connection Condition Specified Condition
2D-17 - 2K-1 Battery voltage not applied to terminals 2A- 48 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4 Below 1 Ω


Main Body ECU (Driver Side Junction Block) for IG1 No. 2 Relay:
Tester Connection Condition Specified Condition
2A-31 - 2K-1 Battery voltage not applied to terminals 2A- 52 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4 Below 1 Ω


Spark Plug:
Recommended spark plug Correct electrode gap for new spark plug Maximum electrode gap for used spark plug Standard insulation resistance
SK16HR11 Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.) 1.3 mm (0.0512 in.) 10 MΩ or higher