Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › MASS AIR FLOW METER
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260408 MASS AIR FLOW METER G

2TR-FE ENGINE CONTROL  MASS AIR FLOW METER  INSPECTION  


PROCEDURE

Hide 22204 1.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

a.

Check the output voltage.

i.
A227197E02
2.594,1.688 2.833,0.688 2.833,0.688 2.688,0.688 false 2.719,1.677 3.083,0.292 3.083,0.292 2.938,0.292 false 2.448,1.74 2.24,2.292 2.24,2.292 2.135,2.292 false 2.479,0.188 2.938,0.396 0.458,0.208 10 false 1 (+B) 2.146,0.604 2.729,0.781 0.583,0.177 10 false 2 (E2G) 1.635,2.198 2.135,2.385 0.5,0.188 10 false 3 (VG)

Apply battery voltage across terminals 1 (+B) and 2 (E2G).

NOTICE:

While using the battery during inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.



ii.

Using a voltmeter, connect the positive (+) tester probe to terminal 3 (VG) and the negative (-) tester probe to terminal 2 (E2G).


iii.

Blow air into the intake mass air flow meter sub-assembly and check that the voltage fluctuates.

Text in Illustration
*a Component without harness connected
(Intake Mass Air Flow Meter Sub-assembly)
V100135

Air

If the result is not as specified, replace the intake mass air flow meter sub-assembly.



b.
A165595E03
1.922,1.529 2.101,1.694 0.179,0.165 10 *1 1.312,2.466 1.838,1.625 false 1.838,1.625 1.915,1.625 false

Perform a visual check for any foreign matter on the platinum hot wire (heater) of the intake mass air flow meter sub-assembly shown in the illustration.

OK:

There is no foreign matter.


Text in Illustration
*1 Platinum Hot Wire (Heater)

If the result is not as specified, replace the intake mass air flow meter sub-assembly.


c.

Check the intake air temperature sensor.

A165586E09
2.054,2.213 1.842,1.859 1.842,1.859 1.674,1.859 false 2.146,2.208 2.322,1.854 2.322,1.854 2.445,1.854 false 0.555,0.448 2.614,1.781 2.06,1.333 2.468,1.786 3.045,1.966 0.578,0.180 10 4 (THA) 4.191,0.059 4.403,0.236 0.211,0.177 10 20 4.191,0.325 4.406,0.512 0.215,0.187 10 10 4.263,0.583 4.405,0.760 0.142,0.177 10 5 4.263,0.774 4.392,0.936 0.129,0.162 10 3 4.263,0.927 4.393,1.088 0.130,0.161 10 2 4.263,1.18 4.409,1.343 0.147,0.163 10 1 4.177,1.454 4.421,1.624 0.244,0.170 10 0.5 4.177,1.626 4.427,1.789 0.250,0.163 10 0.3 4.177,1.796 4.462,1.962 0.284,0.166 10 0.2 4.177,2.042 4.416,2.204 0.239,0.163 10 0.1 4.491,2.307 4.807,2.490 0.316,0.184 10 -20 4.889,2.307 5.011,2.449 0.121,0.142 10 0 5.188,2.307 5.400,2.476 0.211,0.170 10 20 5.532,2.307 5.737,2.469 0.205,0.163 10 40 5.874,2.307 6.106,2.476 0.232,0.170 10 60 6.203,2.307 6.404,2.466 0.201,0.159 10 80 6.524,2.307 6.804,2.480 0.281,0.173 10 100 4.485,2.451 4.748,2.630 0.262,0.179 10 (-4) 4.796,2.451 5.091,2.630 0.295,0.179 10 (32) 5.139,2.451 5.434,2.630 0.295,0.179 10 (68) 5.429,2.451 5.816,2.630 0.387,0.179 10 (104) 5.78,2.451 6.167,2.630 0.387,0.179 10 (140) 6.111,2.451 6.498,2.630 0.387,0.179 10 (176) 6.488,2.451 6.875,2.630 0.387,0.179 10 (212) 5.914,0.757 6.105,0.920 0.191,0.163 10 *d 5.884,0.838 5.736,0.838 5.736,0.838 5.428,1.042 false 3.959,1.001 4.133,1.173 0.175,0.173 10 *b 3.948,0.016 4.159,0.207 0.210,0.191 10 kΩ 5.677,2.606 5.856,2.778 0.179,0.172 10 *c 3.921,2.316 4.406,2.509 0.484,0.193 10 °C (°F) 1.38,1.421 1.583,1.577 0.202,0.157 10 *a 2.348,2.206 2.398,2.256 0.049,0.049 1.222,1.791 1.676,1.979 0.454,0.188 10 5 (E2) 2.015,2.204 2.072,2.262 0.057,0.058 2.127,2.204 2.179,2.256 0.052,0.052

Text in Illustration
*a Component without harness connected
(Intake Mass Air Flow Meter Sub-assembly)
*b Resistance
*c Temperature *d Acceptable Range

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (THA) - 5 (E2) -20°C (-4°F) 12.5 to 16.9 kΩ
20°C (68°F) 2.19 to 2.67 kΩ
60°C (140°F) 0.50 to 0.68 kΩ


If the result is not as specified, replace the intake mass air flow meter sub-assembly.