Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › RELAY › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260417 RELAY G

2TR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INJ NO. 2 RELAY (INJ NO. 2)

a.
A184106E17
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the INJ NO. 2 relay.


Hide 2.INSPECT CIRCUIT OPENING RELAY (C/OPN)

a.
A184106E17
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the circuit opening relay.


Hide 3.INSPECT AIR PUMP HEATER RELAY (AIR PMP HTR)

a.
A184106E17
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the air pump heater relay.


Hide 82641 4.INSPECT NO. 1 INTEGRATION RELAY (IG2)

a.

Check the IG2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 fuse.



b.

Check the IG2 relay.

i.
U115422E06
2.417,1.615 2.646,1.792 0.229,0.177 10 false 1A 1.281,1.615 1.5,1.792 0.219,0.177 10 false 1B 0.406,1.604 0.625,1.781 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 Battery voltage not applied to terminals 1A-1 and 1A-3 10 kΩ or higher
Battery voltage applied to terminals 1A-1 and 1A-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 82641 5.INSPECT NO. 1 INTEGRATION RELAY (EFI)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.

Check the EFI relay.

i.
U115422E07
2.417,1.625 2.646,1.802 0.229,0.177 10 false 1A 1.281,1.625 1.5,1.802 0.219,0.177 10 false 1B 0.406,1.604 0.625,1.781 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 82641 6.INSPECT NO. 1 INTEGRATION RELAY (A/F)

a.

Check the A/F fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω


If the result is not as specified, replace the A/F fuse.



b.
U115422E07
2.417,1.625 2.646,1.802 0.229,0.177 10 false 1A 1.281,1.625 1.5,1.802 0.219,0.177 10 false 1B 0.406,1.604 0.625,1.781 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-8 Battery voltage not applied to terminals 1B-4 and 1B-7 10 kΩ or higher
Battery voltage applied to terminals 1B-4 and 1B-7 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.


Hide 7.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NOTICE:

The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).


a.

Check the ACC fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ACC fuse Always Below 1 Ω


If the result is not as specified, replace the ACC fuse.



b.

Check the ACC relay.

i.

Measure the resistance according to the value(s) in the table below.

U169574E02
0.052,0.031 0.25,0.198 0.198,0.167 10 false *a 0.479,1.24 0.698,1.427 0.219,0.188 10 false 2K 5.854,0.677 6.073,0.865 0.219,0.188 10 false 2D 5.854,2.458 6.073,2.646 0.219,0.188 10 false 2A

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2D-17 - 2K-1 Battery voltage not applied to terminals 2A-48 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.



c.

Check the ECU-IG NO. 1 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω


If the result is not as specified, replace the ECU-IG NO. 1 fuse.



d.

Inspect the IG1 NO. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

U169574E02
0.052,0.031 0.25,0.198 0.198,0.167 10 false *a 0.479,1.24 0.698,1.427 0.219,0.188 10 false 2K 5.854,0.677 6.073,0.865 0.219,0.188 10 false 2D 5.854,2.458 6.073,2.646 0.219,0.188 10 false 2A

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2A-31 - 2K-1 Battery voltage not applied to terminals 2A-52 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.