Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the Three-way Catalytic Converter (TWC), the ECM calculates the Oxygen Storage Capacity (OSC) of the Three-way Catalytic Converter (TWC). This calculation is based on the voltage output of the heated oxygen sensor while performing active air-fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the Three-way Catalytic Converter (TWC). When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the heated oxygen sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the heated oxygen sensor and Three-way Catalytic Converter (TWC).

The ECM uses the OSC value to determine the state of the Three-way Catalytic Converter (TWC). If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0420 OSC value is less than the standard value under active air-fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (Sensor 1)

·

Heated oxygen sensor (Sensor 2)

·

Front exhaust pipe assembly (TWC: Front catalyst and rear catalyst)



CATALYST LOCATION

A229907E02
1.664,1.017 1.917,1.193 0.253,0.177 10 *1 0.81,1.56 1.063,1.736 0.253,0.177 10 *2 2.54,2.971 2.793,3.148 0.253,0.177 10 *3 3.72,1.265 3.973,1.442 0.253,0.177 10 *5 3.381,2.701 3.634,2.878 0.253,0.177 10 *4 1.977,1.473 2.230,1.650 0.253,0.177 10 *6 5.486,2.544 5.739,2.721 0.253,0.177 10 *7 4.849,0.562 5.102,0.739 0.253,0.177 10 *8 1.227,1.874 1.405,1.08 false 1.405,1.08 1.629,1.08 false 0.483,1.918 0.624,1.623 false 0.624,1.623 0.771,1.623 false 2.055,2.674 2.305,3.038 false 2.305,3.038 2.515,3.038 false 2.715,2.512 3.013,2.764 false 3.013,2.764 3.335,2.764 false 3.047,2.282 3.419,1.349 false 3.419,1.349 3.692,1.349 false 4.605,2.2 4.918,2.617 false 4.918,2.617 5.451,2.617 false 5.739,0.934 5.542,0.628 false 5.542,0.628 5.023,0.628 false 2.607,1.826 2.445,1.539 false 2.445,1.539 2.152,1.539 false

Text in Illustration
*1 Exhaust Manifold *2 Air Fuel Ratio Sensor
*3 TWC: Front Catalyst *4 TWC: Rear Catalyst
*5 Front Exhaust Pipe Assembly *6 Heated Oxygen Sensor
*7 Center Exhaust Pipe Assembly *8 Tailpipe Assembly

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor, heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor, mass air flow meter sub-assembly, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa (570 mmHg) or higher
Idling OFF
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10 to 80%
All of following conditions (a), (b) and (c) met -
(a) Mass air flow 3 to 50 gm/sec
(b) Estimated front catalyst temperature 625 to 840°C (1157 to 1544°F)
(c) Estimated rear catalyst temperature 585 to 800°C (1085 to 1472°F)
Transmission gear A/T: 3rd or higher
M/T: 4th or higher

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969E97
1.927,0.313 1.719,0.313 1.719,0.313 1.323,0.875 false 0.74,1.146 1.26,1.396 0.521,0.25 10 false 37 mph 0.833,2.229 1.229,2.5 0.396,0.271 10 false Idling 0.146,2.417 1.281,2.656 1.135,0.24 10 false Ignition Switch off 1.479,2.74 2.063,3.177 0.583,0.438 10 false Warming up 2.365,2.729 3.083,3.25 0.719,0.521 10 false 10 minutes or more 4.135,2.74 4.854,3.135 0.719,0.396 10 false 10 minutes or more 1.969,0.25 3.625,0.542 1.656,0.292 10 false Between 47 and 63 mph 1.667,2.094 1.906,2.333 0.24,0.24 10 false [A] 2.604,1 2.927,1.292 0.323,0.292 10 false [B]* 3.156,3.125 3.396,3.333 0.24,0.208 10 false [C] 6.771,3.115 7.063,3.365 0.292,0.25 10 false [H] 4.271,2.083 4.594,2.469 0.323,0.385 10 false [C] 3.469,2.063 3.688,2.385 0.219,0.323 10 false [D] 6.188,0.635 6.583,0.896 0.396,0.26 10 false [G]* 4.375,1 4.729,1.198 0.354,0.198 10 false [E]* 5,3.146 5.24,3.427 0.24,0.281 10 false [F] 3.365,2.74 3.969,3.125 0.604,0.385 10 false Warming up 5.885,2.74 6.635,3.135 0.75,0.396 10 false 10 minutes or more 0.24,3.396 5.292,3.698 5.052,0.302 10 false *: Drive the vehicle while keeping the engine load as constant as possible

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the GTS on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

14.

Check if any DTCs (pending DTCs) are stored.

15.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Check if any DTCs (pending DTCs) are stored.


CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E74
4.906,3.073 4.906,3.292 false 4.906,3.292 5.26,3.292 false 5.198,3.073 5.198,3.292 false 3.625,0.896 3.885,1.125 0.26,0.229 10 (c) 0.573,0.646 1.583,0.865 1.01,0.219 10 Engine Speed 0.844,1.01 1.615,1.208 0.771,0.198 10 3000 rpm 0.844,1.583 1.594,1.781 0.75,0.198 10 2000 rpm 1.115,2.51 1.583,2.802 0.469,0.292 10 Idling 0.354,2.74 1.521,3 1.167,0.26 10 Ignition Switch off 1.656,2.646 1.917,2.885 0.26,0.24 10 (a) 2.073,2.438 2.354,2.688 0.281,0.25 10 (b) 4.792,0.896 5.063,1.146 0.271,0.25 10 (d) 5.094,1.458 5.406,1.74 0.313,0.281 10 (d) 2.094,3.104 3.01,3.302 0.917,0.198 10 Warming up 3.365,3.104 4.542,3.302 1.177,0.198 10 At least 3 minutes 5.302,3.219 6.115,3.417 0.813,0.198 10 2 seconds 4.865,3.323 5.333,3.542 0.469,0.219 10 Check 6.635,2.76 7.021,3.042 0.385,0.281 10 Time

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter (TWC)) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).



A121610E44
0.07,0.068 4.351,0.243 4.281,0.175 10 Voltage output when active air-fuel ratio control not performed: 2.374,0.421 3.663,0.601 1.289,0.180 10 Normal Catalyst 4.744,0.426 6.216,0.574 1.472,0.148 10 Deteriorated Catalyst 0.018,2.037 1.314,2.700 1.296,0.663 10 Waveform of Heated Oxygen Sensor behind Three-way Catalytic Converter 0.018,0.499 1.451,1.207 1.432,0.708 10 Waveform of Air Fuel Ratio Sensor in front of Three-way Catalytic Converter 1.486,0.789 1.863,0.937 0.378,0.148 10 3.5 V 1.486,1.123 1.884,1.266 0.399,0.143 10 3.0 V 1.486,2.104 1.833,2.253 0.347,0.150 10 1.0 V 1.486,2.774 1.776,2.922 0.290,0.148 10 0 V 2.64,3.111 3.396,3.257 0.755,0.146 10 10 seconds 5.042,3.08 5.796,3.221 0.755,0.141 10 10 seconds

CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

After performing repairs, drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern and check if DTC P0420 is output again. If a DTC is output again, replace the catalyst if it has not been replaced already.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P0420 is output A
P0420 and other DTCs are output B

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leaks from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Lean/Rich Lean Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean Lean Actual air fuel ratio lean
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system


D

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently below 3.1 V, and the heated oxygen sensor voltage (O2S) is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

5.REPLACE AIR FUEL RATIO SENSOR

C

6.CHECK FOR EXHAUST GAS LEAK

D

8.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.




OK

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)
HINT:

Refer to the illustration in Catalyst Location to confirm which parts to replace.


a.

Replace the front exhaust pipe assembly.



NEXT

END

5.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.




OK

7.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

7.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
8.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of the extremely rich or lean actual air fuel ratio while referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0171).



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
P0420 is output A
No DTC is output B

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

11.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

B

END

11.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)
HINT:

Refer to the illustration in Catalyst Location to confirm which parts to replace.


a.

Replace the front exhaust pipe assembly.



NEXT

END