Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

Stand-by RAM Initialized
ECM power source Below 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0560.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A348203E06
0.979,1.781 1.885,2.052 0.906,0.271 10 false Battery 2.229,0.865 2.656,1.104 0.427,0.24 10 false P/I-B 3.896,0.875 4.198,1.125 0.302,0.25 10 false EFI 6.083,2.188 6.542,2.448 0.458,0.26 10 false ECM 5.906,1.302 6.365,1.563 0.458,0.26 10 false E1 5.906,0.719 6.365,0.979 0.458,0.26 10 false BATT 5.479,0.719 5.938,0.979 0.458,0.26 10 false G180 5.49,1.302 5.948,1.563 0.458,0.26 10 false C153 5.708,0.51 5.99,0.719 0.281,0.208 10 false 3 5.708,1.094 5.99,1.302 0.281,0.208 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G180-3 (BATT) - Positive (+) battery cable terminal Always Below 1 Ω
G180-3 (BATT) or Positive (+) battery cable terminal - Body ground Always 10 kΩ or higher




OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted (See page Power Source / Network>2TR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Wait 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

B