Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E46
4.483,0.815 6.151,0.978 1.668,0.163 10 Camshaft Position Sensor 4.483,1.325 6.216,1.485 1.733,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.802,3.922 2.203,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.483,1.827 6.744,1.981 2.260,0.154 10 Mass Air Flow Meter sub-assembly 4.483,2.854 6.827,3.042 2.344,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.031,2.511 1.547,0.167 10 Throttle Position Sensor 4.483,3.353 5.938,3.506 1.455,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 5.098,4.400 1.438,0.184 10 Camshaft Timing Gear 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in the camshaft timing oil control valve assembly (for intake side) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake side) circuit

·

Camshaft timing oil control valve assembly (for intake side)

·

ECM



HINT:

This DTC relates to the camshaft timing oil control valve assembly (for intake side).


MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly (for intake side) and the camshaft timing gear. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly (for intake side). This control signal regulates the oil pressure supplied to the camshaft timing gear. The camshaft timing gear can advance or retard the intake camshaft.

After the ECM sends the target duty-cycle signal to the camshaft timing oil control valve assembly (for intake side), the ECM monitors the camshaft timing oil control valve current to establish an actual duty-cycle. The ECM determines the existence of a malfunction and stores the DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A133814E50
0.167,2.146 2.896,2.521 2.729,0.375 10 false Camshaft Timing Oil Control Valve assembly (for intake side) 5.438,0.875 5.938,1.146 0.5,0.271 10 false OC1+ 5.448,1.802 6.125,2.115 0.677,0.313 10 false OC1- 5.948,2.531 6.531,2.76 0.583,0.229 10 false ECM 0.167,1.99 0.729,2.24 0.563,0.25 10 false C54 1.521,1.615 1.854,1.938 0.333,0.323 10 false 2 1.51,0.854 1.771,1.104 0.26,0.25 10 false 1 5.948,2.396 6.406,2.625 0.458,0.229 10 false C153 5.198,0.875 5.542,1.146 0.344,0.271 10 false 11 5.198,1.625 5.542,1.927 0.344,0.302 10 false 10

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs after recording the freeze frame data and DTCs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine and allow it to idle. Then check for DTCs.


d.

Check that P0010 is not output.

OK:

P0010 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)
a.

Inspect the camshaft timing oil control valve assembly (for intake side) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for intake side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-1 - C153-11 (OC1+) Always Below 1 Ω
C54-2 - C153-10 (OC1-) Always Below 1 Ω
C54-1 or C153-11 (OC1+) - Body ground Always 10 kΩ or higher
C54-2 or C153-10 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR