Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  


DESCRIPTION

The secondary air injection system consists of an air pump, the air switching valve, an air pressure sensor, the air injection control driver and the ECM. For a short time after cold engine starts, the air injection system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the air switching valve.

The air injection control driver drives the air switching valve and the air pump according to command signals transmitted by the ECM. The air pressure sensor detects the pressure in the secondary air passage when the air injection system is ON and OFF, and transmits pressure signal to the ECM.

The air injection control driver is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the air injection system circuit.

HINT:

As a large current is required to drive the air pump and air switching valve, an air injection control driver is included in this system.


A121746E11
0.018,0.141 0.702,0.471 0.684,0.330 10 Diagnostic Signal 3.699,0.643 4.696,0.825 0.997,0.181 10 Pressure Signal 2.086,1.225 3.169,1.406 1.082,0.181 10 Command Signal 0.494,2.126 1.731,2.446 1.237,0.320 10 Air Injection Control Driver 1.391,0.646 1.717,0.828 0.326,0.181 10 ECM 1.768,2.346 2.974,2.650 1.206,0.304 10 Air Switching Valve Drive Signal 3.03,3.229 3.765,3.410 0.735,0.181 10 Reed Valve 4.723,1.019 6.432,1.199 1.710,0.181 10 Air Pressure Sensor 5.426,1.363 6.802,1.544 1.376,0.181 10 Air Pump Drive Signal 6.267,2.055 6.594,2.236 0.328,0.181 10 Filter 5.556,3.383 6.144,3.564 0.588,0.181 10 Air Pump 3.858,3.542 5.065,3.704 1.207,0.161 10 Air Switching Valve 1.738,1.391 2.046,1.286 2.046,1.286 1.297,1.37 false 2.47,1.962 2.389,2.328 false 3.296,2.906 3.404,3.218 false 3.459,2.667 4.387,3.524 false 4.218,1.977 4.674,1.098 false 5.016,1.697 5.375,1.448 false 0.805,0.692 0.691,0.229 false

DTC No. DTC Detection Condition Trouble Area
P2431 Air pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
·

Air pressure sensor

·

Open or short in air pressure sensor circuit

·

ECM


P2432 While engine running, voltage output of air pressure sensor remains below 0.5 V (1 trip detection logic)
·

Air pressure sensor

·

Open or short in air pressure sensor circuit

·

ECM


P2433 While engine running, voltage output of air pressure sensor remains above 4.5 V (1 trip detection logic)
·

Air pressure sensor

·

Open or short in air pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E28
0.017,0.321 1.600,0.611 1.583,0.290 10 Air Pressure Sensor 2.55,0.219 2.875,0.400 0.326,0.181 10 ECM 2.31,0.832 2.774,1.013 0.463,0.181 10 VCA1 2.31,1.474 2.551,1.655 0.241,0.181 10 AIP 0.832,1.611 1.073,1.793 0.241,0.181 10 AIP 2.31,2.098 2.688,2.280 0.378,0.181 10 EAIP 0.866,1.033 1.076,1.214 0.210,0.181 10 VC 0.88,2.207 1.067,2.388 0.187,0.181 10 E2 3.027,3.266 3.414,3.394 0.387,0.128

The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the cylinder head cover.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the air pressure sensor or circuit and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Air pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing Next.

12.

Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

13.

Check for pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2431, P2432 or P2433.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


WIRING DIAGRAM

A345888E06
5.281,0.99 5.74,1.188 0.458,0.198 10 false C153 5.406,0.823 5.719,1.021 0.313,0.198 10 false 20 5.281,1.563 5.74,1.76 0.458,0.198 10 false C153 5.406,1.375 5.719,1.573 0.313,0.198 10 false 26 5.281,2.104 5.74,2.302 0.458,0.198 10 false C153 5.385,1.906 5.698,2.104 0.313,0.198 10 false 25 5.688,0.885 6.302,1.083 0.615,0.198 10 false VCAI 5.698,1.469 6.156,1.667 0.458,0.198 10 false AIP 5.677,2.01 6.292,2.208 0.615,0.198 10 false EAIP 6.01,2.958 6.469,3.156 0.458,0.198 10 false ECM 0.313,2.698 0.771,2.896 0.458,0.198 10 false C137 0.313,2.875 3.219,3.073 2.906,0.198 10 false Air Pressure Sensor 1.375,0.833 1.688,1.031 0.313,0.198 10 false VC 1.385,1.448 1.844,1.646 0.458,0.198 10 false AIP 1.406,1.99 1.719,2.188 0.313,0.198 10 false E2 1.708,0.844 1.865,1.042 0.156,0.198 10 false 3 1.698,1.406 1.854,1.604 0.156,0.198 10 false 2 1.677,1.969 1.833,2.167 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR PRESSURE SENSOR - ECM)
a.

Disconnect the air pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-1 (E2) - C153-25 (EAIP) Always Below 1 Ω
C137-2 (AIP) - C153-26 (AIP) Always Below 1 Ω
C137-3 (VC) - C153-20 (VCAI) Always Below 1 Ω
C137-2 (AIP) or C153-26 (AIP) - Body ground Always 10 kΩ or higher
C137-3 (VC) or C153-20 (VCAI) - Body ground Always 10 kΩ or higher




OK

2.INSPECT ECM (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (SENSOR POWER SOURCE CIRCUIT)
U147496E02
1.688,1.438 1.688,1.854 false 1.469,1.417 1.208,1.854 false 1.469,1.417 1.208,1.854 false 1.906,1.427 2.25,1.865 false 0.177,0.135 0.375,0.333 0.198,0.198 10 false *a 2.156,1.875 2.396,2.021 0.24,0.146 10 false VC 1.531,1.854 1.844,2.021 0.313,0.167 10 false AIP 1.021,1.865 1.229,2.021 0.208,0.156 10 false E2 0.625,1.219 1,1.385 0.375,0.167 10 false C137

a.

Disconnect the air pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C137-3 (VC) - C137-1 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Air Pressure Sensor)



OK

3.READ DATA LIST (PUMP PRESSURE (ABSOLUTE))

NG

3.READ DATA LIST (PUMP PRESSURE (ABSOLUTE))
a.
A273766

Connect a pressure gauge to the air pressure sensor as shown in the illustration.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute).


f.

Check that the pressure displayed on the GTS fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.

OK:

Pressure fluctuates in response to pressure applied with pressure gauge.


HINT:

The GTS displays the air pump pressure (Air pump pressure (absolute)) as absolute pressure.




OK

NG

REPLACE AIR PRESSURE SENSOR