Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM D

2TR-FE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is output, confirm the freeze frame data.



A159471E05
1.881,0.227 2.627,0.376 0.746,0.149 10 DTC stored 0.283,2.633 2.633,2.810 2.350,0.177 10 Freeze frame data which can be read 2.706,1.147 3.362,1.344 0.656,0.198 10 (Seconds) 2.947,1.8 3.290,1.956 0.343,0.156 10 Time 2.156,1.147 2.382,1.316 0.225,0.170 10 0.5 1.331,1.147 1.557,1.316 0.225,0.170 10 0.5 0.498,1.147 0.723,1.316 0.225,0.170 10 0.5

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data, including the data values at the time when the DTC is stored, can be checked.

-

3 data sets before the DTC is stored.

-

1 data set when the DTC is stored.

-

1 data set after the DTC is stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.




PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

-

Using the GTS, the DTCs cleared.


-

The cable is disconnected from the negative (-) battery terminal.


-

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.



A251781E87
0.156,0.104 6.896,0.594 6.74,0.49 10 When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 0.146,1.625 1.24,1.802 1.094,0.177 10 Ignition Switch 1.302,1.458 2.115,1.75 0.813,0.292 10 ON 1.302,1.844 1.552,2.021 0.25,0.177 10 Off 0.156,2.583 1.198,2.896 1.042,0.313 10 Pending Freeze Frame Data 1.333,2.5 1.781,2.698 0.448,0.198 10 Stored 1.323,2.781 1.833,3.104 0.51,0.323 10 Not Stored 0.125,3.708 1.031,4.438 0.906,0.729 10 Freeze Frame Data 1.292,3.667 1.74,3.865 0.448,0.198 10 Stored 0.365,4.698 1.75,4.906 1.385,0.208 10 : Malfunction detected 0.365,5 2.083,5.208 1.719,0.208 10 : Malfunction not detected 2.073,0.885 2.76,1.094 0.688,0.208 10 (First Trip) 2.823,0.885 3.781,1.125 0.958,0.24 10 (Second Trip) 3.781,0.885 4.74,1.125 0.958,0.24 10 (Third Trip) 4.594,0.896 5.552,1.135 0.958,0.24 10 (Fourth Trip) 1.302,3.938 1.813,4.26 0.51,0.323 10 Not Stored

A251782E90
0.188,0.177 7.063,0.594 6.875,0.417 10 false When a 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 0.604,1.531 1.521,1.844 0.917,0.313 10 false Ignition Switch 1.781,1.365 2.302,1.583 0.521,0.219 10 false ON 1.781,1.719 2.125,1.896 0.344,0.177 10 false Off 0.479,2.323 1.542,2.688 1.063,0.365 10 false Pending Freeze Frame Data A 0.479,3.271 1.542,3.635 1.063,0.365 10 false Pending Freeze Frame Data B 1.781,2.25 2.24,2.417 0.458,0.167 10 false Stored 1.781,3.156 2.24,3.323 0.458,0.167 10 false Stored 1.781,2.531 2.24,2.927 0.458,0.396 10 false Not Stored 1.781,3.448 2.24,3.844 0.458,0.396 10 false Not Stored 0.677,4.104 3.188,4.344 2.51,0.24 10 false : Pending malfunction A detected 0.677,4.573 3.188,4.813 2.51,0.24 10 false : Pending malfunction B detected 0.677,5.042 2.771,5.271 2.094,0.229 10 false : No malfunction detected 4.198,2.875 5.302,3.052 1.104,0.177 10 false Uploaded 2.635,0.719 3.333,1.031 0.698,0.313 10 false (First Trip) 3.542,0.719 4.677,0.99 1.135,0.271 10 false (Second Trip) 4.604,0.719 5.729,1.052 1.125,0.333 10 false (Third Trip) 5.521,0.719 6.719,1.052 1.198,0.333 10 false (Fourth Trip)



LIST OF FREEZE FRAME DATA


Refer to "Data List / Active Test" (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).