Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  


DESCRIPTION

·

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the duty-cycle for the camshaft timing oil control valve is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (Variable Valve Timing) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E80
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.823 3.323,5.052 3.323,5.052 3.854,5.052 false 4.479,0.813 6.156,1.042 1.677,0.229 10 false Camshaft Position Sensor 4.479,1.323 6.688,1.844 2.208,0.521 10 false Crankshaft Position Sensor 0.073,0.063 1.76,0.458 1.688,0.396 10 false VVT System: 2.333,1.99 3.938,2.417 1.604,0.427 10 false Target Valve Timing 2.333,1.292 4.156,1.865 1.823,0.573 10 false Actual Valve Timing 2.688,2.698 3.76,3.146 1.073,0.448 10 false Correction 2.823,3.208 3.604,3.646 0.781,0.438 10 false ECM 1.604,3.76 4.219,4.188 2.615,0.427 10 false Camshaft Timing Oil Control Valve 0.167,2.688 1.167,3.104 1,0.417 10 false Duty Cycle 4.479,1.823 7.073,2.385 2.594,0.563 10 false Mass Air Flow Meter sub-assembly 4.479,2.854 7.156,3.375 2.677,0.521 10 false Engine Coolant Temperature Sensor 4.479,2.344 6.354,2.771 1.875,0.427 10 false Throttle Position Sensor 4.479,3.354 6.365,3.75 1.885,0.396 10 false Vehicle Speed Sensor 0.375,4.271 1.979,4.656 1.604,0.385 10 false Engine Oil Pressure 3.656,4.219 6.344,4.448 2.688,0.229 10 false Camshaft Timing Exhaust Gear Assembly 3.885,4.958 5.333,5.552 1.448,0.594 10 false Exhaust Camshaft

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in the camshaft timing oil control valve assembly (for exhaust side) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust side) circuit

·

Camshaft timing oil control valve assembly (for exhaust side)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve assembly for (exhaust side) circuit. If the duty-cycle for the camshaft timing oil control valve assembly (for exhaust side) is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0013.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A133814E52
0.167,2.146 2.917,2.5 2.75,0.354 10 false Camshaft Timing Oil Control Valve Assembly (for Exhaust Side) 5.438,0.875 5.823,1.052 0.385,0.177 10 false OE1+ 5.448,1.802 5.802,1.979 0.354,0.177 10 false OE1- 5.948,2.531 6.333,2.688 0.385,0.156 10 false ECM 0.167,1.99 0.448,2.146 0.281,0.156 10 false C17 1.521,1.615 1.667,1.771 0.146,0.156 10 false 2 1.5,0.865 1.646,1.021 0.146,0.156 10 false 1 5.948,2.396 6.385,2.573 0.438,0.177 10 false C153 5.198,0.875 5.406,1.031 0.208,0.156 10 false 9 5.198,1.604 5.406,1.76 0.208,0.156 10 false 8

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC (DTC P0013)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs after recording the freeze frame data and DTCs.


c.

Turn the ignition switch off.


d.

Allow the engine to idle and check DTCs.


e.

Check that P0013 is output.

OK:

P0013 is output.




OK

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust Side) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for exhaust side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-1 - C153-9 (OE1+) Always Below 1 Ω
C17-2 - C153-8 (OE1-) Always Below 1 Ω
C17-1 or C153-9 (OE1+) - Body ground Always 10 kΩ or higher
C17-2 or C153-8 (OE1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR