Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P1613  Secondary Air Injection System Driver  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P1613 Either of following conditions (1) or (2) met
(1) All of following conditions met (1 trip detection logic):
·

Either of air pump or air switching valve not operating

·

Diagnostic signal from air injection control driver 80%

·

Battery voltage 8 V or more


(2) Both of following conditions met (1 trip detection logic):
·

Battery voltage 8 V or more

·

Diagnostic signal from air injection control driver abnormal (duty signal other than 0, 20, 40, 80 and 100%)


·

Air injection control driver

·

Open in air injection control driver ground circuit


P1613

All of following conditions met (1 trip detection logic):

(a)

Secondary air injection system operating (air switching valve ON and air pump ON)

(b)

Diagnostic signal from air injection control driver 0%

(c)

Battery voltage 8 V or more



·

Short in diagnostic information signal circuit (air injection control driver - ECM)

·

Open or short in air pump and air switching valve command signal circuit (air injection control driver - ECM)

·

Open in air injection control driver ground circuit

·

Air injection control driver

·

ECM


P1613

Both of following conditions met (1 trip detection logic):

(a)

Battery voltage 8 V or more

(b)

Diagnostic signal from air injection control driver 100%



·

Open or short in air injection control driver power source circuit

·

Open in diagnostic information signal circuit (air injection control driver - ECM)

·

Air injection control driver

·

ECM



MONITOR DESCRIPTION

For a short time after cold engine starts, the ECM transmits command signals to the Air Injection Control Driver (AID) to drive the air pump and the Air Switching Valve (ASV). The AID detects open and short circuits according to the voltages at the AID terminals to the air pump and ASV, and the circuit voltage of the AID power source, and transmits diagnostic information as a signal to the ECM.

If the Secondary Air Injection (AIR) system circuit or the AID itself malfunctions, the AID sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM stores the DTC based on the diagnostic information from the AID.

EXAMPLE:

1.

The duty ratio of the diagnostic signal from the AID is 0 or 100% (remains at 0 V or the same as battery voltage).

2.

The duty ratio of the diagnostic signal from the AID shows an impossible ratio (other than 0, 20, 40, 80 and 100%).

3.

The AID outputs the normal signal (normal duty signal: 80%) while the system is not operating.


MONITOR STRATEGY

Required Sensors/Components Air injection control driver
Frequency of Operation Once per drive cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press the ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P1613.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result:
Display (DTC Output) Proceed To
P1613 A
P1613 and other DTCs B


HINT:

If any DTCs other than P1613 are output, troubleshoot those DTCs first.




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
U147502E02
1.948,1.083 2.135,1.563 false 1.385,1.083 1.177,1.563 false 0.646,0.99 0.958,1.167 0.313,0.177 10 false A16 0.188,0.094 0.344,0.271 0.156,0.177 10 false *a 2.031,1.594 2.24,1.771 0.208,0.177 10 false +B 1.073,1.594 1.281,1.771 0.208,0.177 10 false E

a.

Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A16-5 (+B) - A16-1 (E) Ignition Switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Injection Control Driver)



OK

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G180-6 (AIRP) - A16-4 (SIP) Always Below 1 Ω
G180-5 (AIRV) - A16-3 (SIV) Always Below 1 Ω
G181-20 (AIDI) - A16-2 (DI) Always Below 1 Ω
A16-1 (E) - Body ground Always Below 1 Ω
G180-6 (AIRP) or A16-4 (SIP) - Body ground Always 10 kΩ or higher
G180-5 (AIRV) or A16-3 (SIV) - Body ground Always 10 kΩ or higher
G181-20 (AIDI) or A16-2 (DI) - Body ground Always 10 kΩ or higher




OK

4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
U147503E02
1.375,1.083 1.177,1.573 false 1.552,1.083 1.74,1.563 false 0.646,0.979 0.948,1.156 0.302,0.177 10 false A16 0.188,0.094 0.344,0.271 0.156,0.177 10 false *a 1.104,1.583 1.292,1.76 0.188,0.177 10 false E 1.656,1.583 1.865,1.76 0.208,0.177 10 false DI

a.

Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A16-2 (DI) - A16-1 (E) Ignition Switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Injection Control Driver)



OK

5.PERFORM ACTIVE TEST USING GTS

NG

5.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the air injection control driver connector.


b.
U147663E03
1.396,2.594 1.229,3.073 false 1.531,2.563 1.552,3.063 false 1.688,2.604 1.948,3.042 false 1.813,2.604 2.354,3.073 false 0.635,2.479 0.927,2.656 0.292,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.156,3.083 1.344,3.26 0.188,0.177 10 false E 1.469,3.083 1.677,3.26 0.208,0.177 10 false DI 1.844,3.083 2.24,3.26 0.396,0.177 10 false SIV 2.271,3.083 2.677,3.26 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.74 2.885,0.917 0.438,0.177 10 false AIDI 2.448,1.083 2.896,1.26 0.448,0.177 10 false AIRV 0.865,0.729 1.073,0.906 0.208,0.177 10 false DI 0.781,1.083 1.177,1.26 0.396,0.177 10 false SIV

Connect terminals DI and SIV of the wire harness connector for the air injection control driver.


Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)

c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the secondary air injection system intrusive operation while the engine is idling.


i.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.


j.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-3 (SIV) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



k.
U147664E03
1.375,2.594 1.229,3.073 false 1.521,2.583 1.552,3.063 false 1.667,2.594 1.99,3.073 false 1.823,2.604 2.354,3.073 false 0.635,2.479 0.938,2.656 0.302,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.156,3.083 1.344,3.26 0.188,0.177 10 false E 1.469,3.083 1.677,3.26 0.208,0.177 10 false DI 1.844,3.083 2.24,3.26 0.396,0.177 10 false SIV 2.271,3.083 2.677,3.26 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.729 2.896,0.906 0.448,0.177 10 false AIDI 2.448,1.083 2.906,1.26 0.458,0.177 10 false AIRP 0.865,0.729 1.073,0.906 0.208,0.177 10 false DI 0.781,1.083 1.177,1.26 0.396,0.177 10 false SIP

Connect terminals DI and SIP of the wire harness connector for the air injection control driver.


Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)

l.

Connect the GTS to the DLC3.


m.

Turn the ignition switch to ON.


n.

Turn the GTS on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the secondary air injection system intrusive operation while the engine is idling.


r.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.


s.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-4 (SIP) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

6.REPLACE AIR INJECTION CONTROL DRIVER

NG

6.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
7.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.



g.

Turn the ignition switch off and wait for at least 30 seconds.


h.

Turn the ignition switch to ON.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


j.

Start the engine after the GTS initialization is finished.


k.

Perform the System Check operation by pressing ENTER (Next).


l.

After operating the secondary air injection system, press the Exit button to confirm the secondary air injection system pending codes.


m.

Check Pending DTCs.

OK:

No pending DTC output.



n.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG