Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit  P0121  Throttle Pedal Position Sensor / Switch "A" Circuit Range / Performance  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

The throttle position sensor is mounted on the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

U169147E02
4.396,1.51 4.646,1.052 4.646,1.052 4.74,1.052 false 0.833,1.573 0.885,2.198 false 1.25,1.094 0.927,1.896 false 0.885,2.938 1.365,3.563 false 0.865,2.583 0.479,3.125 false 5.719,0.531 5.885,0.531 5.885,0.531 6.146,1.854 false 5.531,2.25 5.896,2.552 false 5.521,2.365 5.521,2.177 false 3.958,1.656 4.208,1.813 0.25,0.156 10 false 4.8 4.573,1.917 4.948,2.083 0.375,0.167 10 false VTA2 4.969,2.708 5.344,2.875 0.375,0.167 10 false VTA1 3.823,2.26 4.198,2.417 0.375,0.156 10 false 2.60* 3.896,2.406 4.198,2.563 0.302,0.156 10 false 2.25 3.833,2.74 4.188,2.896 0.354,0.156 10 false 0.97* 3.896,2.885 4.198,3.042 0.302,0.156 10 false 0.69 3.958,1.417 4.188,1.573 0.229,0.156 10 false 5.0 4.792,0.99 5.771,1.146 0.979,0.156 10 false Fail-safe Angle 2.677,1.01 4.344,1.188 1.667,0.177 10 false Sensor Output Voltage (V) 6.479,3.406 6.833,3.563 0.354,0.156 10 false 86° 4.354,3.125 4.531,3.281 0.177,0.156 10 false 7° 4.167,3.417 4.427,3.573 0.26,0.156 10 false 0° 1.969,1.135 2.313,1.302 0.344,0.167 10 false ECM 1.302,1.75 1.719,1.906 0.417,0.156 10 false VCTA 1.302,2.75 1.646,2.906 0.344,0.156 10 false ETA 1.302,2.083 1.698,2.24 0.396,0.156 10 false VTA1 1.302,2.417 1.698,2.573 0.396,0.156 10 false VTA2 1.271,1.031 1.792,1.208 0.521,0.177 10 false Magnet 1.396,3.479 1.917,3.656 0.521,0.177 10 false Magnet 0.302,1.49 0.885,1.667 0.583,0.177 10 false IC No. 1 0.302,3.146 0.896,3.323 0.594,0.177 10 false IC No. 2 0.031,0.656 1.635,0.833 1.604,0.177 10 false Throttle Position Sensor 0.073,3.708 0.51,3.875 0.438,0.167 10 false Note: 0.073,4.021 3.396,4.365 3.323,0.344 10 false The throttle valve opening angle detected by sensor terminal VTA1 is expressed as a percentage. 0.073,4.771 3.438,4.958 3.365,0.188 10 false Between 10% and 22%: Throttle valve fully closed 0.073,5.104 3.5,5.26 3.427,0.156 10 false Between 67.2% and 99.2%: Throttle valve fully open 0.073,5.438 2.792,5.594 2.719,0.156 10 false Approximately 19.4%: Fail-safe angle (7°) 4.031,0.448 5.719,0.635 1.688,0.188 10 false Line indicating VTA2 x 0.8 3.604,4.573 5.677,4.75 2.073,0.177 10 false Characteristics of sensor output: 5.896,2.51 6.354,2.729 0.458,0.219 10 false 1.11 V 5.104,3.677 7.135,3.875 2.031,0.198 10 false Throttle Valve Opening Angle (°) 4.948,3.323 6.094,3.521 1.146,0.198 10 false Usable Range 4.646,4.083 6.24,4.281 1.594,0.198 10 false *: During fail-safe control 3.604,5.646 7.042,5.823 3.438,0.177 10 false (VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V) 3.604,4.938 7.104,5.271 3.5,0.333 10 false The difference in voltage between VTA1 and VTA2 x 0.8 is approximately 1.11 V.

DTC Code DTC Detection Condition Trouble Area
P0120 The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0121 The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


P0122 The output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 The output voltage of VTA1 is 4.535 V or higher for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short between VC and VTA1 circuits

·

ECM


P0220 The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0222 The output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short between VC and VTA2 circuits

·

ECM


P2135 Either condition (a) or (b) is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM



HINT:
·

When any of these DTCs are output, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Throttle Position No. 1 and Throttle Position No. 2.


·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition)
GTS Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 4.98 V



MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.


If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

P0121

The ECM uses the TP sensor to monitor the throttle valve opening angle.

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm proper operation of the TP sensor and VTA1.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the TP sensor. The ECM illuminates the MIL and sets the DTC.

If the malfunction is not repaired successfully, the DTC is set 2 seconds after the engine is next started.


FAIL-SAFE

When any of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating fail-safe mode until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

for Automatic Transmission

A227101E07
0.667,3.882 2.884,4.073 2.217,0.191 10 Throttle Body with Motor Assembly 0.671,3.685 1.030,3.898 0.360,0.213 10 C13 5.406,3.852 5.747,4.008 0.341,0.156 10 ECM 5.406,3.667 5.692,3.823 0.286,0.156 10 C36 2.01,1.164 2.305,1.328 0.295,0.164 10 VTA 1.964,1.781 2.333,1.937 0.369,0.156 10 VTA2 2.104,2.43 2.334,2.586 0.230,0.156 10 VC 2.126,3.036 2.345,3.175 0.218,0.140 10 E2 2.433,1.054 2.551,1.223 0.118,0.170 10 6 2.444,1.693 2.569,1.841 0.125,0.148 10 4 2.437,2.31 2.559,2.501 0.121,0.191 10 5 2.445,2.934 2.564,3.076 0.119,0.142 10 3 4.594,1.052 4.778,1.199 0.184,0.147 10 1 4.594,1.687 4.782,1.833 0.187,0.146 10 9 4.594,2.311 4.787,2.467 0.193,0.156 10 2 4.594,2.93 4.782,3.118 0.187,0.188 10 3 4.783,1.052 5.152,1.217 0.369,0.165 10 VTA1 4.784,1.687 5.153,1.834 0.369,0.147 10 VTA2 4.775,2.313 5.172,2.450 0.397,0.137 10 VCTA 4.784,2.93 5.116,3.095 0.331,0.165 10 ETA 5.957,2.206 6.164,2.374 0.207,0.168 10 5V

for Manual Transmission

A227101E03
0.667,3.882 2.884,4.073 2.217,0.191 10 Throttle Body with Motor Assembly 0.671,3.685 1.030,3.832 0.360,0.147 10 C13 5.406,3.852 5.747,4.008 0.341,0.156 10 ECM 5.406,3.667 5.692,3.823 0.286,0.156 10 C36 2.01,1.164 2.305,1.328 0.295,0.164 10 VTA 1.964,1.781 2.333,1.937 0.369,0.156 10 VTA2 2.104,2.43 2.334,2.586 0.230,0.156 10 VC 2.126,3.036 2.345,3.175 0.218,0.140 10 E2 2.433,1.054 2.551,1.223 0.118,0.170 10 6 2.444,1.693 2.569,1.841 0.125,0.148 10 4 2.437,2.31 2.559,2.501 0.121,0.191 10 5 2.445,2.934 2.564,3.076 0.119,0.142 10 3 4.527,1.052 4.711,1.199 0.184,0.147 10 15 4.542,1.687 4.729,1.833 0.187,0.146 10 16 4.535,2.311 4.728,2.467 0.193,0.156 10 13 4.542,2.93 4.729,3.071 0.187,0.141 10 14 4.783,1.052 5.152,1.217 0.369,0.165 10 VTA1 4.784,1.687 5.153,1.834 0.369,0.147 10 VTA2 4.775,2.313 5.172,2.450 0.397,0.137 10 VCTA 4.784,2.93 5.116,3.095 0.331,0.165 10 ETA 5.957,2.206 6.164,2.374 0.207,0.168 10 5V

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the throttle position sensor.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Throttle / Throttle Position No. 1 and Throttle Position No. 2.


d.

Check the values displayed on the GTS.

Result
Throttle Position No. 1 Throttle Position No. 2 Throttle Position No. 1 Throttle Position No. 2 Trouble Area Proceed to
When Accelerator Pedal Released When Accelerator Pedal Depressed
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V E2 circuit open
0 to 0.2 V,
or 4.5 to 4.98 V
2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 4.98 V
VTA2 circuit open or ground short
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 4.98 V
(Not fail-safe)
Throttle position sensor circuit normal B


HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Calculate the voltage of VTA1 and VTA2 according to Throttle Sensor Volt % and Throttl Sensor #2 Volt % respectively and confirm their consistency.

Example:

Throttle Sensor Volt % / 100 (%) x 5 (V) = Throttle Position No.1

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No.1

VTA2: Throttle Position No.2



·

If DTC P0121 is output, proceed to "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C13-5 (VC) - C36-2 (VCTA) Always Below 1 Ω
C13-6 (VTA) - C36-1 (VTA1) Always Below 1 Ω
C13-4 (VTA2) - C36-9 (VTA2) Always Below 1 Ω
C13-3 (E2) - C36-3 (ETA) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C13-5 (VC) - C36-13 (VCTA) Always Below 1 Ω
C13-6 (VTA) - C36-15 (VTA1) Always Below 1 Ω
C13-4 (VTA2) - C36-16 (VTA2) Always Below 1 Ω
C13-3 (E2) - C36-14 (ETA) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C13-5 (VC) or C36-2 (VCTA) - Body ground Always 10 kΩ or higher
C13-6 (VTA) or C36-1 (VTA1) - Body ground Always 10 kΩ or higher
C13-4 (VTA2) or C36-9 (VTA2) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C13-5 (VC) or C36-13 (VCTA) - Body ground Always 10 kΩ or higher
C13-6 (VTA) or C36-15 (VTA1) - Body ground Always 10 kΩ or higher
C13-4 (VTA2) or C36-16 (VTA2) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle body with motor assembly connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
U147500E02
1.646,1.115 1.448,1.604 false 1.958,1.115 2.146,1.594 false 0.646,0.99 0.948,1.167 0.302,0.177 10 false C13 0.188,0.094 0.344,0.271 0.156,0.177 10 false *a 1.344,1.625 1.531,1.802 0.188,0.177 10 false E2 2.094,1.615 2.302,1.792 0.208,0.177 10 false VC

a.

Disconnect the throttle body with motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C13-5 (VC) - C13-3 (E2) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


c.

Reconnect the throttle body with motor assembly connector.



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the throttle with motor body assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine.


e.

Allow the engine to idle for 15 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 A
No output B



A

B

SYSTEM OK