Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 An open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A227108E02
1.185,2.318 1.660,2.483 0.475,0.165 10 Battery 1.918,1.287 2.260,1.442 0.342,0.155 10 P/I-B 3.527,1.271 3.780,1.455 0.253,0.184 10 EFI 5.291,0.918 5.468,1.097 0.177,0.179 10 24 5.234,1.109 5.546,1.264 0.312,0.155 10 G55 5.28,2.158 5.474,2.322 0.194,0.165 10 12 5.238,2.341 5.524,2.499 0.285,0.158 10 C36 5.582,1.103 5.958,1.267 0.376,0.165 10 BATT 5.578,2.338 5.772,2.505 0.194,0.166 10 E1 5.957,3.262 6.299,3.427 0.342,0.165 10 ECM 3.348,0.997 3.456,1.160 0.107,0.163 10 1 3.804,0.997 3.911,1.160 0.107,0.163 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)
a.

Check the harness and connector between the EFI fuse and ECM.

i.

Remove the EFI fuse from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
EFI fuse terminal 2 - G55-24 (BATT) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
EFI fuse terminal 2 or G55-24 (BATT) - Body ground Always 10 kΩ or higher



iv.

Reinstall the EFI fuse.


v.

Reconnect the ECM connector.



b.

Check the harness and connector between the EFI fuse and battery.

i.

Remove the EFI fuse from the engine room relay block.


ii.

Disconnect the cable from the positive (+) battery terminal.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Battery positive terminal - EFI fuse terminal 1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Battery positive terminal or EFI fuse terminal 1 - Body ground Always 10 kΩ or higher



iv.

Reinstall the EFI fuse.


v.

Reconnect the cable to the positive (+) battery terminal.




OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and turn the GTS off.


e.

Start the engine and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0560 A
No output B



A

B