Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2102 Conditions (a) and (b) are met for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator duty ratio is 80% or more.
(b) The throttle actuator current is 0.5 A or less.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either condition is met (1 trip detection logic):
·

A hybrid IC diagnosis signal failure.

·

A hybrid IC current limiter port failure.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM




MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, it becomes stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

Example:

When the electrical current is 0.5 A or less and the throttle actuator duty ratio is 80% or more, the ECM interprets this as the current being outside the standard range, illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved to a high rpm several times after the engine has idled for 5 seconds after engine start.



FAIL-SAFE

When either of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

for Automatic Transmission

A227104E11
1.385,3.26 1.688,3.438 0.302,0.177 10 false C13 1.385,3.427 3.615,3.667 2.229,0.24 10 false Throttle Body with Motor Assembly 0.927,4.115 1.385,4.313 0.458,0.198 10 false Battery 3.969,3.104 4.563,3.281 0.594,0.177 10 false Shielded 5.573,0.813 5.771,0.969 0.198,0.156 10 false 6 5.479,1 5.75,1.146 0.271,0.146 10 false C36 5.813,0.896 6.156,1.063 0.344,0.167 10 false +BM 5.542,1.958 5.76,2.125 0.219,0.167 10 false 19 5.49,2.156 5.771,2.354 0.281,0.198 10 false C37 5.542,2.583 5.74,2.75 0.198,0.167 10 false 20 5.49,2.771 5.771,2.927 0.281,0.156 10 false C37 2.771,2.063 3,2.219 0.229,0.156 10 false M+ 2.781,2.677 2.99,2.823 0.208,0.146 10 false M- 3.063,2.052 3.177,2.208 0.115,0.156 10 false 2 3.063,2.667 3.177,2.833 0.115,0.167 10 false 1 5.531,3.188 5.729,3.344 0.198,0.156 10 false 15 5.49,3.375 5.781,3.531 0.292,0.156 10 false C37 5.521,3.771 5.719,3.938 0.198,0.167 10 false 29 5.49,3.958 5.781,4.104 0.292,0.146 10 false C36 5.521,4.365 5.719,4.552 0.198,0.188 10 false 12 5.49,4.552 5.792,4.698 0.302,0.146 10 false C36 5.813,2.052 6.042,2.229 0.229,0.177 10 false M+ 5.813,2.677 6.01,2.823 0.198,0.146 10 false M- 5.813,3.354 6.198,3.521 0.385,0.167 10 false GE01 5.813,3.854 6.198,4 0.385,0.146 10 false ME01 5.813,4.542 6.01,4.719 0.198,0.177 10 false E1 6.125,5.115 6.479,5.281 0.354,0.167 10 false ECM 2.896,1.146 3.302,1.333 0.406,0.188 10 false ETCS

for Manual Transmission

A227104E05
1.381,3.265 1.678,3.426 0.298,0.161 10 C13 1.388,3.426 3.610,3.619 2.222,0.193 10 Throttle Body with Motor Assembly 0.927,4.11 1.389,4.313 0.461,0.202 10 Battery 3.982,3.102 4.554,3.281 0.573,0.179 10 Shielded 2.89,1.132 3.296,1.315 0.406,0.183 10 ETCS 5.536,0.803 5.743,0.954 0.207,0.151 10 23 5.494,0.987 5.785,1.133 0.291,0.146 10 C36 5.812,0.897 6.153,1.062 0.341,0.165 10 +BM 5.537,1.96 5.784,2.097 0.247,0.137 10 20 5.5,2.154 5.785,2.347 0.286,0.193 10 C37 5.539,2.587 5.738,2.751 0.199,0.163 10 29 5.501,2.768 5.784,2.919 0.283,0.151 10 C36 2.767,2.061 3.000,2.217 0.232,0.156 10 M+ 2.781,2.677 2.985,2.824 0.204,0.147 10 M- 3.066,2.054 3.183,2.210 0.117,0.156 10 2 3.065,2.671 3.174,2.840 0.110,0.170 10 1 5.535,3.186 5.728,3.342 0.193,0.156 10 30 5.501,3.368 5.794,3.523 0.293,0.156 10 C36 5.532,3.775 5.725,3.945 0.193,0.170 10 10 5.501,3.955 5.795,4.101 0.294,0.146 10 C37 5.531,4.368 5.724,4.556 0.193,0.188 10 12 5.5,4.548 5.803,4.689 0.303,0.142 10 C36 5.816,2.056 6.046,2.235 0.230,0.179 10 M+ 5.812,2.672 6.005,2.819 0.193,0.147 10 M- 5.812,3.354 6.200,3.524 0.387,0.170 10 GE01 5.815,3.859 6.198,4.002 0.383,0.144 10 ME01 5.815,4.54 6.010,4.712 0.195,0.172 10 E1 6.13,5.11 6.480,5.275 0.350,0.165 10 ECM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>THROTTLE BODY>INSPECTION).

HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C13-2 (M+) - C37-19 (M+) Always Below 1 Ω
C13-1 (M-) - C37-20 (M-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C13-2 (M+) - C37-20 (M+) Always Below 1 Ω
C13-1 (M-) - C36-29 (M-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C13-2 (M+) or C37-19 (M+) - Body ground Always 10 kΩ or higher
C13-1 (M-) or C37-20 (M-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C13-2 (M+) or C37-20 (M+) - Body ground Always 10 kΩ or higher
C13-1 (M-) or C36-29 (M-) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle body with motor assembly connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and housing.

OK:

No foreign objects between the throttle valve and housing.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

4.INSPECT THROTTLE VALVE

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE VALVE
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the throttle body with motor assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY