Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The camshaft oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E04
4.427,0.815 6.407,1.026 1.980,0.211 10 Camshaft Position Sensor 4.427,1.325 6.521,1.485 2.094,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 4.515,3.922 2.917,0.174 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.427,1.827 6.016,1.981 1.589,0.154 10 Mass Air Flow Meter 4.427,2.854 6.780,3.042 2.353,0.188 10 Engine Coolant Temperature Sensor 4.427,2.344 6.211,2.511 1.784,0.167 10 Throttle Position Sensor 4.427,3.353 6.169,3.506 1.742,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 6.982,4.400 3.323,0.184 10 VVT Controller (Camshaft Timing Gear Assembly) 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC Code DTC Detection Condition Trouble Area
P0010 An open or short in the camshaft timing oil control valve assembly (for intake side of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake side of bank 1) circuit

·

Camshaft timing oil control valve assembly (for intake side of bank 1)

·

ECM


P0020 An open or short in the camshaft timing oil control valve assembly (for intake side of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake side of bank 2) circuit

·

Camshaft timing oil control valve assembly (for intake side of bank 2)

·

ECM



WIRING DIAGRAM

for Automatic Transmission
A227098E03
0.126,1.686 2.958,2.014 2.833,0.329 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 1) 0.136,3.676 2.912,4.043 2.776,0.367 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 2) 1.471,0.521 1.602,0.717 0.130,0.197 10 1 1.483,1.249 1.599,1.479 0.116,0.230 10 2 1.425,2.48 1.581,2.661 0.156,0.181 10 1 1.475,3.223 1.587,3.425 0.111,0.203 10 2 5.098,0.407 5.314,0.584 0.215,0.178 10 31 5.075,0.611 5.362,0.766 0.287,0.155 10 C34 5.119,1.144 5.340,1.340 0.221,0.197 10 32 5.111,2.384 5.309,2.554 0.198,0.169 10 33 5.119,3.119 5.298,3.297 0.179,0.178 10 34 5.078,1.348 5.350,1.507 0.272,0.159 10 C34 5.064,2.583 5.352,2.742 0.288,0.159 10 C34 5.074,3.325 5.352,3.493 0.278,0.168 10 C34 0.153,1.483 0.425,1.642 0.272,0.159 10 C16 0.171,3.446 0.443,3.596 0.272,0.149 10 C18 5.4,0.509 5.807,0.667 0.407,0.159 10 OC1+ 5.401,1.25 5.787,1.418 0.385,0.168 10 OC1- 5.396,2.486 5.791,2.654 0.395,0.168 10 OC2+ 5.401,3.221 5.760,3.380 0.360,0.159 10 OC2- 5.91,4.185 6.241,4.336 0.331,0.152 10 ECM


for Manual Transmission
A227098E02
0.126,1.686 2.958,2.014 2.833,0.329 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 1) 0.136,3.676 2.912,4.043 2.776,0.367 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 2) 1.471,0.521 1.602,0.717 0.130,0.197 10 1 1.483,1.249 1.599,1.479 0.116,0.230 10 2 1.425,2.48 1.581,2.661 0.156,0.181 10 1 1.475,3.223 1.587,3.425 0.111,0.203 10 2 5.098,0.407 5.314,0.584 0.215,0.178 10 19 5.075,0.611 5.362,0.766 0.287,0.155 10 C35 5.119,1.144 5.302,1.340 0.183,0.197 10 20 5.111,2.384 5.309,2.554 0.198,0.169 10 19 5.119,3.119 5.298,3.297 0.179,0.178 10 20 5.078,1.348 5.350,1.507 0.272,0.159 10 C35 5.064,2.583 5.352,2.742 0.288,0.159 10 C34 5.074,3.325 5.352,3.493 0.278,0.168 10 C34 0.153,1.483 0.425,1.642 0.272,0.159 10 C16 0.171,3.446 0.443,3.596 0.272,0.149 10 C18 5.4,0.509 5.807,0.667 0.407,0.159 10 OC1+ 5.401,1.25 5.787,1.418 0.385,0.168 10 OC1- 5.396,2.486 5.791,2.654 0.395,0.168 10 OC2+ 5.401,3.221 5.760,3.380 0.360,0.159 10 OC2- 5.91,4.185 6.241,4.336 0.331,0.152 10 ECM


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC
a.

Clear the DTC after recording the freeze frame data and DTC.


b.

Turn the engine switch off.


c.

Allow the engine to idle and check for DTC.


d.

Check that P0010 or P0020 is output.

OK:

P0010 or P0020 is output.




OK

2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2)

NG

2.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2)
a.

Inspect the camshaft timing oil control valve assembly (for Intake Side of Bank 1, 2) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE OF BANK 1, 2)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Reconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C16-1 - C34-31 (OC1+) Always Below 1 Ω
C18-1 - C34-33 (OC2+) Always Below 1 Ω
C16-2 - C34-32 (OC1-) Always Below 1 Ω
C18-2 - C34-34 (OC2-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C16-1 - C35-19 (OC1+) Always Below 1 Ω
C18-1 - C34-19 (OC2+) Always Below 1 Ω
C16-2 - C35-20 (OC1-) Always Below 1 Ω
C18-2 - C34-20 (OC2-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C16-1 or C34-31 (OC1+) - Body ground Always 10 kΩ or higher
C18-1 or C34-33 (OC2+) - Body ground Always 10 kΩ or higher
C16-2 or C34-32 (OC1-) - Body ground Always 10 kΩ or higher
C18-2 or C34-34 (OC2-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C16-1 or C35-19 (OC1+) - Body ground Always 10 kΩ or higher
C18-1 or C34-19 (OC2+) - Body ground Always 10 kΩ or higher
C16-2 or C35-20 (OC1-) - Body ground Always 10 kΩ or higher
C18-2 or C34-20 (OC2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft timing oil control valve assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR