Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A193433E12
5.954,1.173 5.688,1.537 false 0.473,0.796 2.214,0.999 1.741,0.203 10 Crankshaft Position Sensor 0.652,1.281 1.969,1.649 1.317,0.368 10 Mass Air Flow Meter Sub-assembly 0.568,2.077 2.120,2.280 1.552,0.203 10 Throttle Position Sensor 0.65,3.448 2.041,3.651 1.391,0.203 10 Vehicle Speed Signal 0.544,3.963 2.113,4.319 1.569,0.356 10 Camshaft Position (VVT) Sensor 3.643,1.326 4.930,1.529 1.287,0.203 10 Target Valve Timing 3.97,3.196 4.646,3.406 0.676,0.211 10 Correction 3.647,4.028 4.922,4.231 1.274,0.203 10 Actual Valve Timing 4.068,0.202 4.485,0.405 0.417,0.203 10 ECM 5.982,1.003 6.812,1.206 0.830,0.203 10 Duty Control 5.926,2.929 7.018,3.427 1.092,0.499 10 Camshaft Timing Oil Control Valve Assembly 4.567,2.503 5.423,2.706 0.856,0.203 10 Feedback 0.69,2.619 2.001,2.957 1.311,0.338 10 Engine Coolant Temperature Sensor

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in the camshaft timing oil control valve assembly (for exhaust side of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust side of bank 1) circuit

·

Camshaft timing oil control valve assembly (for exhaust side of bank 1)

·

ECM


P0023 Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust side of bank 2) circuit

·

Camshaft timing oil control valve assembly (for exhaust side of bank 2)

·

ECM



WIRING DIAGRAM

for Automatic Transmission
A227099E03
0.126,1.667 2.958,1.996 2.833,0.329 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 1) 0.136,3.657 2.912,4.024 2.776,0.367 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 2) 1.471,0.502 1.602,0.698 0.130,0.197 10 1 1.483,1.23 1.599,1.460 0.116,0.230 10 2 1.425,2.461 1.581,2.642 0.156,0.181 10 1 1.475,3.204 1.587,3.407 0.111,0.203 10 2 5.098,0.388 5.314,0.566 0.215,0.178 10 35 5.075,0.592 5.362,0.747 0.287,0.155 10 C34 5.119,1.125 5.405,1.322 0.286,0.197 10 36 5.111,2.365 5.419,2.535 0.309,0.169 10 30 5.119,3.1 5.364,3.278 0.245,0.178 10 24 5.078,1.33 5.350,1.488 0.272,0.159 10 C34 5.064,2.564 5.369,2.723 0.305,0.159 10 C34 5.074,3.306 5.352,3.475 0.278,0.168 10 C34 0.153,1.464 0.425,1.623 0.272,0.159 10 C17 0.171,3.428 0.443,3.577 0.272,0.149 10 C19 5.4,0.49 5.807,0.648 0.407,0.159 10 OE1+ 5.401,1.231 5.787,1.399 0.385,0.168 10 OE1- 5.396,2.467 5.791,2.636 0.395,0.168 10 OE2+ 5.401,3.203 5.760,3.361 0.360,0.159 10 OE2- 5.859,4.202 6.259,4.396 0.400,0.194 12 ECM


for Manual Transmission
A227099E02
0.126,1.667 2.958,1.996 2.833,0.329 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 1) 0.136,3.657 2.912,4.024 2.776,0.367 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 2) 1.471,0.502 1.602,0.698 0.130,0.197 10 1 1.483,1.23 1.599,1.460 0.116,0.230 10 2 1.425,2.461 1.581,2.642 0.156,0.181 10 1 1.475,3.204 1.587,3.407 0.111,0.203 10 2 5.098,0.388 5.314,0.566 0.215,0.178 10 21 5.075,0.592 5.362,0.747 0.287,0.155 10 C35 5.119,1.125 5.302,1.322 0.183,0.197 10 22 5.111,2.365 5.309,2.535 0.198,0.169 10 21 5.119,3.1 5.298,3.278 0.179,0.178 10 22 5.078,1.33 5.350,1.488 0.272,0.159 10 C35 5.064,2.564 5.369,2.723 0.305,0.159 10 C34 5.074,3.306 5.352,3.475 0.278,0.168 10 C34 0.153,1.464 0.425,1.623 0.272,0.159 10 C17 0.171,3.428 0.443,3.577 0.272,0.149 10 C19 5.4,0.49 5.807,0.648 0.407,0.159 10 OE1+ 5.401,1.231 5.787,1.399 0.385,0.168 10 OE1- 5.396,2.467 5.791,2.636 0.395,0.168 10 OE2+ 5.401,3.203 5.760,3.361 0.360,0.159 10 OE2- 5.859,4.202 6.259,4.396 0.400,0.194 12 ECM


CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is output, check the exhaust camshaft circuit for the right bank VVT system (bank 1).

·

Bank 1 refers to the bank that includes cylinder No. 1.

·

If DTC P0023 is output, check the exhaust camshaft circuit for the left bank VVT system (bank 2).

·

Bank 2 refers to the bank that does not include cylinder No. 1.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC (DTC P0013 OR P0023)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0013 is output A
DTC P0023 is output B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1))

B

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 2))
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).


e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% (OFF) Normal engine speed
127% (ON) Engine idles roughly or stalls soon after camshaft timing oil control valve assembly switched from off to on




OK

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 2))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 2).


e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% (OFF) Normal engine speed
127% (ON) Engine idles roughly or stalls soon after camshaft timing oil control valve assembly switched from off to on




OK

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE OF BANK 1, 2)

5.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C17-1 - C34-35 (OE1+) Always Below 1 Ω
C17-2 - C34-36 (OE1-) Always Below 1 Ω
C19-1 - C34-30 (OE2+) Always Below 1 Ω
C19-2 - C34-24 (OE2-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C17-1 - C35-21 (OE1+) Always Below 1 Ω
C17-2 - C35-22 (OE1-) Always Below 1 Ω
C19-1 - C34-21 (OE2+) Always Below 1 Ω
C19-2 - C34-22 (OE2-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C17-1 or C34-35 (OE1+) - Body ground Always 10 kΩ or higher
C17-2 or C34-36 (OE1-) - Body ground Always 10 kΩ or higher
C19-1 or C34-30 (OE2+) - Body ground Always 10 kΩ or higher
C19-2 or C34-24 (OE2-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C17-1 or C35-21 (OE1+) - Body ground Always 10 kΩ or higher
C17-2 or C35-22 (OE1-) - Body ground Always 10 kΩ or higher
C19-1 or C34-21 (OE2+) - Body ground Always 10 kΩ or higher
C19-2 or C34-22 (OE2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft timing oil control valve assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)