Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft's VVT sensor consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.

When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crank angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft rotation. Based on a combination of the VVT signals and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
There is no exhaust VVT sensor signal for 5 seconds at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor for exhaust side circuit

·

VVT sensor for exhaust side

·

Exhaust camshaft

·

ECM


P0367
P0392
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust side circuit

·

VVT sensor for exhaust side

·

Exhaust camshaft

·

ECM


P0368
P0393
Output voltage of the VVT sensor for exhaust side (bank 1, 2) is more than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust side circuit

·

VVT sensor for exhaust side

·

Exhaust camshaft

·

ECM



A228079E01
1.063,2.829 2.046,3.030 0.983,0.201 10 20 msec./DIV. 0.088,0.811 0.651,0.977 0.563,0.166 10 5 V/DIV. 0.195,1.477 0.479,1.678 0.284,0.201 10 NE 0.11,1.975 0.477,2.176 0.367,0.201 10 EV1 3.031,1.494 3.363,1.695 0.332,0.201 10 GND 3.031,2.095 3.363,2.296 0.332,0.201 10 GND 3.031,2.491 3.363,2.692 0.332,0.201 10 GND 0.11,2.37 0.477,2.571 0.367,0.201 10 EV2 0.35,0.274 2.756,0.475 2.406,0.201 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

EV1+ and EV2+ are the VVT sensor signal, and NE+ is the crankshaft position sensor signal.

·

The wavelength becomes shorter as the engine speed increases.

Item Content
Terminal NE+ - NE-
EV1+ - VV1-
EV2+ - VV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Idling with warm engine




WIRING DIAGRAM

for Automatic Transmission

A160377E22
0.587,2.242 0.917,2.418 0.330,0.177 10 C22 0.587,2.403 2.174,2.580 1.586,0.177 10 VVT Sensor (for Bank 1) 0.587,3.882 0.917,4.059 0.330,0.177 10 C23 0.587,4.043 2.250,4.220 1.663,0.177 10 VVT Sensor (for Bank 2) 1.402,1.198 1.721,1.351 0.319,0.152 10 VC2 1.842,1.289 1.984,1.466 0.142,0.177 10 3 4.877,1.289 5.158,1.466 0.281,0.177 10 12 4.931,1.671 5.113,1.848 0.182,0.177 10 9 4.877,2.054 5.112,2.231 0.236,0.177 10 11 1.402,1.584 1.801,1.736 0.399,0.152 10 EX+ 1.842,1.675 1.984,1.851 0.142,0.177 10 1 5.121,1.198 5.593,1.351 0.471,0.152 10 VCV1 5.121,1.584 5.520,1.736 0.399,0.152 10 EV1+ 5.121,1.95 5.482,2.141 0.360,0.192 10 VV1- 4.916,2.931 5.147,3.108 0.231,0.177 10 6 4.923,3.333 5.113,3.510 0.189,0.177 10 3 4.923,3.712 5.113,3.888 0.189,0.177 10 5 5.121,2.861 5.593,3.013 0.471,0.152 10 VCV2 5.121,3.246 5.520,3.399 0.399,0.152 10 EV2+ 5.121,3.612 5.482,3.804 0.360,0.192 10 VV2- 1.842,2.039 1.984,2.216 0.142,0.177 10 2 1.842,2.935 1.984,3.112 0.142,0.177 10 3 1.842,3.321 1.984,3.497 0.142,0.177 10 1 1.842,3.685 1.984,3.862 0.142,0.177 10 2 5.677,4.248 6.029,4.404 0.351,0.156 10 C34 5.677,4.383 6.045,4.539 0.368,0.156 10 ECM 1.402,1.941 1.745,2.093 0.344,0.152 10 EX- 1.416,2.88 1.735,3.032 0.319,0.152 10 VC2 1.416,3.265 1.815,3.417 0.399,0.152 10 EX+ 1.416,3.622 1.759,3.774 0.344,0.152 10 EX-

for Manual Transmission

A160377E07
0.587,2.242 0.917,2.418 0.330,0.177 10 C22 0.587,2.403 2.174,2.580 1.586,0.177 10 VVT Sensor (for Bank 1) 0.587,3.882 0.917,4.059 0.330,0.177 10 C23 0.587,4.043 2.250,4.220 1.663,0.177 10 VVT Sensor (for Bank 2) 1.402,1.198 1.721,1.351 0.319,0.152 10 VC2 1.842,1.289 1.984,1.466 0.142,0.177 10 3 4.877,1.289 5.158,1.466 0.281,0.177 10 15 4.877,1.671 5.112,1.848 0.236,0.177 10 13 4.877,2.054 5.112,2.231 0.236,0.177 10 14 1.402,1.584 1.801,1.736 0.399,0.152 10 EX+ 1.842,1.675 1.984,1.851 0.142,0.177 10 1 5.121,1.198 5.593,1.351 0.471,0.152 10 VCV1 5.121,1.584 5.520,1.736 0.399,0.152 10 EV1+ 5.121,1.95 5.482,2.141 0.360,0.192 10 EV1- 4.877,2.931 5.147,3.108 0.270,0.177 10 16 4.877,3.333 5.112,3.510 0.236,0.177 10 18 4.877,3.727 5.112,3.904 0.236,0.177 10 17 5.121,2.861 5.593,3.013 0.471,0.152 10 VCV2 5.121,3.246 5.520,3.399 0.399,0.152 10 EV2+ 5.121,3.612 5.482,3.804 0.360,0.192 10 EV2- 1.842,2.039 1.984,2.216 0.142,0.177 10 2 1.842,2.935 1.984,3.112 0.142,0.177 10 3 1.842,3.321 1.984,3.497 0.142,0.177 10 1 1.842,3.685 1.984,3.862 0.142,0.177 10 2 5.362,4.248 5.713,4.404 0.351,0.156 10 C34 5.362,4.383 5.730,4.539 0.368,0.156 10 ECM 1.402,1.941 1.745,2.093 0.344,0.152 10 EX- 1.416,2.88 1.735,3.032 0.319,0.152 10 VC2 1.416,3.265 1.815,3.417 0.399,0.152 10 EX+ 1.416,3.622 1.759,3.774 0.344,0.152 10 EX-

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.



PROCEDURE

1.CHECK VVT SENSOR FOR EXHAUST SIDE (SENSOR POWER SOURCE)
a.
U169144E01
1.178,0.397 1.466,0.560 0.288,0.163 10 C22 2.317,1.684 2.774,1.847 0.457,0.163 10 VC2 0.079,0.042 0.269,0.205 0.190,0.163 10 *a 1.96,1.346 2.274,1.674 false 2.064,0.406 2.355,0.569 0.291,0.163 10 C23 2.503,0.421 2.693,0.583 0.190,0.163 10 *B 1.609,0.403 1.799,0.566 0.190,0.163 10 *A

Disconnect the VVT sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C23-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to VVT Sensor)


d.

Reconnect the VVT sensor connector.



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C22-1 (EX+) - C34-9 (EV1+) Always Below 1 Ω
C22-2 (EX-) - C34-11 (VV1-) Always Below 1 Ω
C23-1 (EX+) - C34-3 (EV2+) Always Below 1 Ω
C23-2 (EX-) - C34-5 (VV2-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C22-1 (EX+) - C34-13 (EV1+) Always Below 1 Ω
C22-2 (EX-) - C34-14 (EV1-) Always Below 1 Ω
C23-1 (EX+) - C34-18 (EV2+) Always Below 1 Ω
C23-2 (EX-) - C34-17 (EV2-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C22-1 (EX+) or C34-9 (EV1+) - Body ground Always 10 kΩ or higher
C22-2 (EX-) or C34-11 (VV1-) - Body ground Always 10 kΩ or higher
C23-1 (EX+) or C34-3 (EV2+) - Body ground Always 10 kΩ or higher
C23-2 (EX-) or C34-5 (VV2-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C22-1 (EX+) or C34-13 (EV1+) - Body ground Always 10 kΩ or higher
C22-2 (EX-) or C34-14 (EV1-) - Body ground Always 10 kΩ or higher
C23-1 (EX+) or C34-18 (EV2+) - Body ground Always 10 kΩ or higher
C23-2 (EX-) or C34-17 (EV2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the VVT sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)
a.
BR03795E25
1.521,1.53 2.298,1.731 0.777,0.201 10 Clearance 0.438,1.765 0.706,1.973 0.267,0.209 10 OK 2.63,1.765 2.897,1.973 0.267,0.209 10 NG 2.833,1.978 3.414,2.144 0.581,0.165

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL VVT SENSOR FOR EXHAUST SIDE

4.CHECK EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the exhaust camshaft (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

5.REPLACE VVT SENSOR FOR EXHAUST SIDE

NG

5.REPLACE VVT SENSOR FOR EXHAUST SIDE
a.

Replace the VVT sensor for exhaust side (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 AND/OR P0393)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367, P0368, P0390, P0392 AND/OR P0393)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
DTC P0365, P0367, P0368, P0390, P0392 and/or P0393 are output B

HINT:

If the engine does not start, replace the ECM.




A

REPAIR COMPLETED

B

7.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C22-3 (VC2) - C34-12 (VCV1) Always Below 1 Ω
C23-3 (VC2) - C34-6 (VCV2) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C22-3 (VC2) - C34-15 (VCV1) Always Below 1 Ω
C23-3 (VC2) - C34-16 (VCV2) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C22-3 (VC2) or C34-12 (VCV1) - Body ground Always 10 kΩ or higher
C23-3 (VC2) or C34-6 (VCV2) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C22-3 (VC2) or C34-15 (VCV1) - Body ground Always 10 kΩ or higher
C23-3 (VC2) or C34-16 (VCV2) - Body ground Always 10 kΩ or higher



d.

Reconnect the VVT sensor connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM)