Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0416  Secondary Air Injection System Switching Valve "B" Circuit Open  P0417  Secondary Air Injection System Switching Valve "B" Circuit Shorted  


DESCRIPTION

The ECM operates the air injection VSV relay (AI-VSV) which causes the No. 2 emission control valve set to operate.

DTC No. DTC Detection Condition Trouble Area
P0416 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM


P0417 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in air injection VSV relay (AI-VSV) circuit

·

Air injection VSV relay (AI-VSV)

·

ECM



WIRING DIAGRAM

A227240E05
0.5,3.167 0.885,3.313 0.385,0.146 10 false P/I-B 5.885,1.125 6.188,1.271 0.302,0.146 10 false G56 5.896,3.865 6.26,4.021 0.365,0.156 10 false C35 5.896,1.771 6.219,1.917 0.323,0.146 10 false G56 5.885,5.177 6.167,5.323 0.281,0.146 10 false C35 5.896,4.521 6.177,4.667 0.281,0.146 10 false C35 5.927,0.906 6.125,1.073 0.198,0.167 10 false 36 5.927,1.552 6.125,1.708 0.198,0.156 10 false 24 5.948,4.302 6.156,4.458 0.208,0.156 10 false 13 5.927,4.958 6.135,5.115 0.208,0.156 10 false 14 5.917,3.635 6.115,3.813 0.198,0.177 10 false 16 6.229,1.104 6.688,1.281 0.458,0.177 10 false MREL 6.229,1.76 6.688,1.938 0.458,0.177 10 false AIR1 6.24,3.854 6.646,4.031 0.406,0.177 10 false AIP2 6.229,4.49 6.854,4.667 0.625,0.177 10 false VCAP 6.219,5.167 6.625,5.344 0.406,0.177 10 false EAIP 4.479,3.656 4.76,3.854 0.281,0.198 10 false +BL 4.708,3.865 5.073,4.042 0.365,0.177 10 false AIP2 4.74,4.51 5.292,4.688 0.552,0.177 10 false VC2 4.75,5.177 5.031,5.354 0.281,0.177 10 false E22 4.406,5.333 4.906,5.521 0.5,0.188 10 false GNDL 4.979,1.625 5.115,1.771 0.135,0.146 10 false 2 5,2.281 5.135,2.479 0.135,0.198 10 false 5 4.188,1.615 4.323,1.76 0.135,0.146 10 false 1 4.188,2.281 4.323,2.49 0.135,0.208 10 false 3 3.396,2.719 5.5,2.896 2.104,0.177 10 false Air Injection VSV Relay (AI-VSV) 2.927,1.917 3.552,2.115 0.625,0.198 10 false EFI No. 2 2.375,3.073 3.115,3.396 0.74,0.323 10 false AIR PMP HTR 0.646,1.76 0.844,1.927 0.198,0.167 10 false 1C 0.698,1.979 0.833,2.125 0.135,0.146 10 false 1 1.802,2.115 2.052,2.271 0.25,0.156 10 false EFI 1.177,1.927 1.458,2.083 0.281,0.156 10 false EFI 2.385,1.76 2.583,1.927 0.198,0.167 10 false 1B 2.385,1.125 2.583,1.292 0.198,0.167 10 false 1B 0.646,1.135 0.844,1.302 0.198,0.167 10 false 1B 2.427,1.979 2.563,2.125 0.135,0.146 10 false 4 2.438,0.938 2.573,1.083 0.135,0.146 10 false 2 0.698,0.938 0.833,1.083 0.135,0.146 10 false 3 0.083,0.042 1.188,0.25 1.104,0.208 12 false for Bank 2: 0.635,4.99 1.24,5.156 0.604,0.167 10 false Battery 6.396,5.688 6.792,5.865 0.396,0.177 10 false ECM 1.542,4.104 1.896,4.281 0.354,0.177 10 false ALT 1.167,2.406 2.625,2.615 1.458,0.208 10 false No. 1 Integration Relay 4.677,5.677 4.813,5.823 0.135,0.146 10 false 1 5.167,5.063 5.302,5.208 0.135,0.146 10 false 4 5.146,4.375 5.281,4.521 0.135,0.146 10 false 2 5.156,3.729 5.292,3.875 0.135,0.146 10 false 3 4.667,3.365 4.802,3.51 0.135,0.146 10 false 5 2.354,5.698 4.438,5.927 2.083,0.229 10 false No. 2 Emission Control Valve Set 2.365,5.521 2.667,5.719 0.302,0.198 10 false C45

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR INJECTION VSV RELAY (AI-VSV)
a.

Inspect the air injection VSV relay (AI-VSV) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)

NG

REPLACE AIR INJECTION VSV RELAY (AI-VSV)

2.CHECK AIR INJECTION VSV RELAY (AI-VSV) (POWER SOURCE)
a.

Remove the air injection VSV relay (AI-VSV).


b.

Turn the engine switch on (IG).


c.
A227244E01
0.125,0.157 0.346,0.322 0.221,0.165 10 *1 0.52,2.392 0.741,2.557 0.221,0.165 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 1 - Body ground Engine switch on (IG) 11 to 14 V
Air injection VSV relay (AI-VSV) terminal 3 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 Air Injection VSV Relay (AI-VSV)


d.

Reinstall the air injection VSV relay (AI-VSV).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI-VSV))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION VSV RELAY (AI-VSV))
a.

Remove the air injection VSV relay (AI-VSV).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 2 - G56-24 (AIR1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 2 or G56-24 (AIR1) - Body ground Always 10 kΩ or higher



d.

Reinstall the air injection VSV relay (AI-VSV).


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR