Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) sensor (VV1, 2 signal) of the intake camshaft consists of a magnet and MRE (Magnetoresistive Element).

The VVT camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. DTC Detection Condition Trouble Area
P0340 One of the following conditions is met:
·

Missing VVT sensor (for intake camshaft) signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher (1 trip detection logic).

·

No VVT sensor (for intake camshaft) signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).

·

No VVT sensor (for intake camshaft) signal to ECM while cranking (2 trip detection logic).


·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Timing chain has jumped tooth

·

ECM


P0342
P0347
The output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
P0343
P0348
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
P0345 No VVT sensor (for intake camshaft) signal at engine speed of 600 rpm or higher (1 trip detection logic).

A122767E04
0.195,0.643 0.425,0.808 0.230,0.165 10 NE 0.122,1.13 0.426,1.281 0.304,0.151 10 VV1 0.126,1.512 0.425,1.657 0.299,0.145 10 VV2 2.9,0.633 3.237,0.782 0.336,0.149 10 GND 2.9,1.587 3.237,1.736 0.336,0.149 10 GND 2.9,1.204 3.237,1.353 0.336,0.149 10 GND 0.918,1.915 1.839,2.057 0.921,0.141 10 20 msec./DIV. 2.697,0.047 3.261,0.203 0.563,0.156 10 5 V/DIV.

Reference: Inspection using an oscilloscope (VV1, VV2 and NE Signal Waveforms).

HINT:
·

The correct waveforms are as shown.

·

VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Item Content
Terminal VV1+ - VV1-
VV2+ - VV2-
NE+ - NE-
Equipment Setting 5 V/DIV.,
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

for Automatic Transmission

A160377E21
0.587,2.242 0.917,2.418 0.330,0.177 10 C20 0.587,2.403 2.174,2.580 1.586,0.177 10 VVT Sensor (for Bank 1) 0.587,3.882 0.917,4.059 0.330,0.177 10 C21 0.587,4.043 2.250,4.220 1.663,0.177 10 VVT Sensor (for Bank 2) 1.523,1.198 1.745,1.351 0.222,0.152 10 VC 1.842,1.289 1.984,1.466 0.142,0.177 10 3 4.836,1.289 5.117,1.466 0.281,0.177 10 12 4.843,2.054 5.079,2.231 0.236,0.177 10 11 4.843,1.676 5.079,1.852 0.236,0.177 10 10 1.348,1.584 1.747,1.736 0.399,0.152 10 VVR+ 1.842,1.675 1.984,1.851 0.142,0.177 10 1 1.379,1.948 1.743,2.100 0.364,0.152 10 VVR- 5.121,1.198 5.593,1.351 0.471,0.152 10 VCV1 5.121,1.584 5.520,1.736 0.399,0.152 10 VV1+ 5.121,1.95 5.482,2.141 0.360,0.192 10 VV1- 4.895,3.33 5.102,3.507 0.207,0.177 10 4 4.895,3.708 5.102,3.885 0.207,0.177 10 5 4.895,2.952 5.102,3.129 0.207,0.177 10 6 5.121,2.861 5.593,3.013 0.471,0.152 10 VCV2 5.121,3.246 5.520,3.399 0.399,0.152 10 VV2+ 5.121,3.612 5.482,3.804 0.360,0.192 10 VV2- 1.842,2.039 1.984,2.216 0.142,0.177 10 2 1.523,2.844 1.745,2.997 0.222,0.152 10 VC 1.842,2.935 1.984,3.112 0.142,0.177 10 3 1.348,3.23 1.747,3.382 0.399,0.152 10 VVL+ 1.842,3.321 1.984,3.497 0.142,0.177 10 1 1.379,3.594 1.743,3.746 0.364,0.152 10 VVL- 1.842,3.685 1.984,3.862 0.142,0.177 10 2 5.67,4.248 6.022,4.404 0.351,0.156 10 C34 5.67,4.383 6.038,4.539 0.368,0.156 10 ECM

for Manual Transmission

A160377E06
0.587,2.242 0.917,2.418 0.330,0.177 10 C20 0.587,2.403 2.174,2.580 1.586,0.177 10 VVT Sensor (for Bank 1) 0.587,3.882 0.917,4.059 0.330,0.177 10 C21 0.587,4.043 2.250,4.220 1.663,0.177 10 VVT Sensor (for Bank 2) 1.523,1.198 1.745,1.351 0.222,0.152 10 VC 1.842,1.289 1.984,1.466 0.142,0.177 10 3 4.836,1.289 5.117,1.466 0.281,0.177 10 15 4.893,1.671 5.128,1.848 0.236,0.177 10 9 4.843,2.054 5.079,2.231 0.236,0.177 10 10 1.348,1.584 1.747,1.736 0.399,0.152 10 VVR+ 1.842,1.675 1.984,1.851 0.142,0.177 10 1 1.379,1.948 1.743,2.100 0.364,0.152 10 VVR- 5.121,1.198 5.593,1.351 0.471,0.152 10 VCV1 5.121,1.584 5.520,1.736 0.399,0.152 10 VV1+ 5.121,1.95 5.482,2.141 0.360,0.192 10 VV1- 4.831,2.931 5.102,3.108 0.270,0.177 10 16 4.843,3.333 5.079,3.510 0.236,0.177 10 12 4.854,3.727 5.090,3.904 0.236,0.177 10 11 5.121,2.861 5.593,3.013 0.471,0.152 10 VCV2 5.121,3.246 5.520,3.399 0.399,0.152 10 VV2+ 5.121,3.612 5.482,3.804 0.360,0.192 10 VV2- 1.842,2.039 1.984,2.216 0.142,0.177 10 2 1.523,2.844 1.745,2.997 0.222,0.152 10 VC 1.842,2.935 1.984,3.112 0.142,0.177 10 3 1.348,3.23 1.747,3.382 0.399,0.152 10 VVL+ 1.842,3.321 1.984,3.497 0.142,0.177 10 1 1.379,3.594 1.743,3.746 0.364,0.152 10 VVL- 1.842,3.685 1.984,3.862 0.142,0.177 10 2 5.362,4.248 5.713,4.404 0.351,0.156 10 C34 5.362,4.383 5.730,4.539 0.368,0.156 10 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK VVT SENSOR (SENSOR POWER SOURCE)
a.
U147530E01
1.111,0.414 1.392,0.577 0.281,0.163 10 C20 2.317,1.684 2.593,1.847 0.276,0.163 10 VC 0.079,0.042 0.269,0.205 0.190,0.163 10 *a 1.96,1.346 2.274,1.674 false 2.284,0.423 2.602,0.585 0.318,0.163 10 C21 2.712,0.389 2.902,0.552 0.190,0.163 10 *B 1.523,0.386 1.713,0.549 0.190,0.163 10 *A

Disconnect the VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C20-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V
C21-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V


Text in Illustration
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to VVT Sensor)


c.

Reconnect the VVT sensor connector.



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Automatic Transmission
Tester Connection Condition Specified Condition
C20-1 (VVR+) - C34-10 (VV1+) Always Below 1 Ω
C20-2 (VVR-) - C34-11 (VV1-) Always Below 1 Ω
C21-1 (VVL+) - C34-4 (VV2+) Always Below 1 Ω
C21-2 (VVL-) - C34-5 (VV2-) Always Below 1 Ω

for Manual Transmission
Tester Connection Condition Specified Condition
C20-1 (VVR+) - C34-9 (VV1+) Always Below 1 Ω
C20-2 (VVR-) - C34-10 (VV1-) Always Below 1 Ω
C21-1 (VVL+) - C34-12 (VV2+) Always Below 1 Ω
C21-2 (VVL-) - C34-11 (VV2-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Automatic Transmission
Tester Connection Condition Specified Condition
C20-1 (VVR+) or C34-10 (VV1+) - Body ground Always 10 kΩ or higher
C20-2 (VVR-) or C34-11 (VV1-) - Body ground Always 10 kΩ or higher
C21-1 (VVL+) or C34-4 (VV2+) - Body ground Always 10 kΩ or higher
C21-2 (VVL-) or C34-5 (VV2-) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C20-1 (VVR+) or C34-9 (VV1+) - Body ground Always 10 kΩ or higher
C20-2 (VVR-) or C34-10 (VV1-) - Body ground Always 10 kΩ or higher
C21-1 (VVL+) or C34-12 (VV2+) - Body ground Always 10 kΩ or higher
C21-2 (VVL-) or C34-11 (VV2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the VVT sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
a.
BR03795E17
2.83,1.978 3.414,2.15 0.584,0.172 0.447,1.813 0.721,2.025 0.274,0.212 10 OK 2.63,1.813 2.904,2.025 0.274,0.212 10 NG 1.521,1.538 2.219,1.75 0.698,0.212 10 Clearance

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK VALVE TIMING

NG

4.CHECK VALVE TIMING

OK

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)

NG

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
a.

Check the teeth of the signal plate.

OK:

Sensor plate teeth do not have any cracks or deformation.


HINT:
for Automatic Transmission

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




OK

6.REPLACE VVT SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

6.REPLACE VVT SENSOR

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
No output A
P0340, P0342, P0343, P0345, P0347 or P0348 B

HINT:

If the engine does not start, replace the ECM.




A

END

B