Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure switch is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No. DTC Detection Condition Trouble Area
P0550 Power steering oil pressure switch voltage below 0.28 V, or higher than 4.9 V for 0.5 seconds while engine running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM


P0552 Power steering oil pressure switch voltage below 0.28 V for 0.5 seconds while engine running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM


P0553 Power steering oil pressure switch voltage higher than 4.9 V for 0.5 seconds while engine running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM



WIRING DIAGRAM

for Automatic Transmission

A227106E07
1.865,0.573 2.177,0.74 0.313,0.167 10 false PSP 1.948,1.49 2.167,1.646 0.219,0.156 10 false VC 1.979,2.396 2.188,2.573 0.208,0.177 10 false E2 2.313,0.458 2.469,0.646 0.156,0.188 10 false 2 2.302,1.365 2.427,1.552 0.125,0.188 10 false 1 2.313,2.281 2.427,2.438 0.115,0.156 10 false 3 4.708,0.385 4.906,0.552 0.198,0.167 10 false 17 4.667,0.594 4.958,0.74 0.292,0.146 10 false C36 4.75,1.292 4.948,1.479 0.198,0.188 10 false 6 4.667,1.5 4.958,1.646 0.292,0.146 10 false C34 4.75,2.219 4.865,2.396 0.115,0.177 10 false 4 4.677,2.417 4.948,2.573 0.271,0.156 10 false C36 5.021,0.563 5.406,0.823 0.385,0.26 10 false PSP 5.031,1.479 5.458,1.677 0.427,0.198 10 false VCV2 5.021,2.396 5.49,2.573 0.469,0.177 10 false ETHW 0.427,3.167 2.698,3.333 2.271,0.167 10 false Power Steering Oil Pressure Switch 0.427,3.01 0.698,3.167 0.271,0.156 10 false C29 5.542,3.063 5.885,3.219 0.344,0.156 10 false ECM

for Manual Transmission

A227106E02
1.867,0.577 2.181,0.742 0.314,0.165 10 PSP 1.953,1.493 2.174,1.648 0.221,0.155 10 VC 1.981,2.398 2.192,2.573 0.211,0.174 10 E2 2.31,0.463 2.466,0.647 0.156,0.184 10 2 2.304,1.365 2.429,1.549 0.125,0.184 10 1 2.308,2.286 2.426,2.442 0.119,0.156 10 3 4.704,0.386 4.897,0.552 0.193,0.165 10 16 4.677,0.564 4.965,0.706 0.288,0.142 10 C35 4.708,1.296 4.901,1.482 0.193,0.186 10 16 4.677,1.48 4.969,1.625 0.292,0.145 10 C34 4.752,2.214 4.866,2.391 0.114,0.177 10 8 4.679,2.402 4.951,2.559 0.272,0.157 10 C35 5.023,0.564 5.344,0.702 0.321,0.138 10 PSP 5.034,1.483 5.421,1.648 0.387,0.165 10 VCV2 5.023,2.397 5.466,2.543 0.443,0.147 10 ETHW 0.428,3.171 2.704,3.336 2.276,0.165 10 Power Steering Oil Pressure Switch 0.426,3.012 0.702,3.168 0.276,0.156 10 C29 5.545,3.058 5.886,3.214 0.341,0.156 10 ECM

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure switch and stores a DTC.

CAUTION / NOTICE / HINT

HINT:
·

If other DTCs relating to different systems that have terminal ETHW as the ground terminal are output simultaneously, terminal ETHW may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SWITCH)
a.

Disconnect the power steering oil pressure switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Tester Connection Condition Specified Condition
C29-2 (PSP) - C36-17 (PSP) Always Below 1 Ω
C29-1 (VC) - C34-6 (VCV2) Always Below 1 Ω
C29-3 (E2) - C36-4 (ETHW) Always Below 1 Ω
C29-2 (PSP) or C36-17 (PSP) - Body ground Always 10 kΩ or higher
C29-1 (VC) or C34-6 (VCV2) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
C29-2 (PSP) - C35-16 (PSP) Always Below 1 Ω
C29-1 (VC) - C34-16 (VCV2) Always Below 1 Ω
C29-3 (E2) - C35-8 (ETHW) Always Below 1 Ω
C29-2 (PSP) or C35-16 (PSP) - Body ground Always 10 kΩ or higher
C29-1 (VC) or C34-16 (VCV2) - Body ground Always 10 kΩ or higher



d.

Reconnect the power steering oil pressure switch connector.


e.

Reconnect the ECM connector.



OK

2.REPLACE POWER STEERING OIL PRESSURE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SWITCH
a.

Replace the power steering oil pressure switch (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine.


e.

Idle the engine for 5 seconds.


f.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 is output A
No DTC is output B



A

B

END