Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › RELAY › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260456 RELAY G

1KD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 28610 2.INSPECT GLOW PLUG RELAY (GLOW)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85935 3.INSPECT FUEL PUMP RELAY (FUEL PMP)

a.
B060778E05
0.126,0.705 0.221,0.906 0.095,0.201 10 3 2.968,1.335 3.062,1.536 0.095,0.201 10 3 0.126,1.289 0.221,1.49 0.095,0.201 10 2 1.249,0.728 1.344,0.929 0.095,0.201 10 5 1.249,1.26 1.344,1.462 0.095,0.201 10 1 2.968,0.349 3.062,0.551 0.095,0.201 10 2 2.968,0.819 3.062,1.021 0.095,0.201 10 5 1.553,0.269 1.647,0.471 0.095,0.201 10 1 2.04,0.613 1.724,0.458 false 2.624,0.619 2.928,0.493 false 2.481,1.117 2.91,0.951 false 2.498,1.61 2.922,1.495 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 82641 4.INSPECT NO. 1 INTEGRATION RELAY (IG2)

a.

Check the IG2 fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 fuse.



b.

Check the IG2 relay.

i.
U169305E02
2.417,1.615 2.646,1.76 0.229,0.146 10 false 1A 1.281,1.615 1.49,1.76 0.208,0.146 10 false 1B 0.396,1.625 0.615,1.802 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-5 Battery voltage not applied to terminals 1A-1 and 1A-3 10 kΩ or higher
Battery voltage applied to terminals 1A-1 and 1A-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(Integration Relay)

If the result is not as specified, replace the integration relay.



Hide 82641 5.INSPECT NO. 1 INTEGRATION RELAY (EFI)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.

Check the EFI relay.

i.
U169305E02
2.417,1.615 2.646,1.76 0.229,0.146 10 false 1A 1.281,1.615 1.49,1.76 0.208,0.146 10 false 1B 0.396,1.625 0.615,1.802 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω

Text in Illustration
*a Component without harness connected
(Integration Relay)


If the result is not as specified, replace the integration relay.



Hide 82641 6.INSPECT NO. 1 INTEGRATION RELAY (EDU)

a.
U169305E02
2.417,1.615 2.646,1.76 0.229,0.146 10 false 1A 1.281,1.615 1.49,1.76 0.208,0.146 10 false 1B 0.396,1.625 0.615,1.802 0.219,0.177 10 false 1C 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-8 - 1B-5 Battery voltage not applied to terminals 1B-7 and 1B-4 10 kΩ or higher
Battery voltage applied to terminals 1B-7 and 1B-4 Below 1 Ω

Text in Illustration
*a Component without harness connected
(Integration Relay)


If the result is not as specified, replace the integration relay.


Hide 7.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

NOTICE:

The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).


a.

Inspect the ACC relay.

i.

Measure the resistance according to the value(s) in the table below.

U115459E05
0.771,0.792 0.969,0.938 0.198,0.146 10 false 2K 0.104,0.063 0.302,0.208 0.198,0.146 10 false *a 2.75,0.792 2.948,0.938 0.198,0.146 10 false 2D 5.438,0.781 5.635,0.927 0.198,0.146 10 false 2A

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2D-17 - 2K-1 Battery voltage not applied to terminals 2A-48 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.



b.

Inspect the IG1 No. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

U115459E05
0.771,0.792 0.969,0.938 0.198,0.146 10 false 2K 0.104,0.063 0.302,0.208 0.198,0.146 10 false *a 2.75,0.792 2.948,0.938 0.198,0.146 10 false 2D 5.438,0.781 5.635,0.927 0.198,0.146 10 false 2A

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2A-31 - 2K-1 Battery voltage not applied to terminals 2A-52 and 2D-4 10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4 Below 1 Ω


If the result is not as specified, replace the main body ECU.