Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM M

1KD-FTV ENGINE CONTROL  ECD SYSTEM  REGISTRATION  


PROCEDURE

Hide 1. LEARNING VALUES CONFIRMATION

This procedure uses the intelligent tester to display the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM.

A202032E48
0.104,0.073 2,0.417 1.896,0.344 10 false Learning Values Confirmation: 2.677,0.625 3.021,0.896 0.344,0.271 10 false Start 2.635,1.5 3.073,1.781 0.438,0.281 10 false Notice 2.469,2.354 3.208,2.625 0.74,0.271 10 false Select Item 2.01,4.917 3.677,5.208 1.667,0.292 10 false Confirm Learning Value(s) 2.49,4.375 2.813,4.625 0.323,0.25 10 false Next 2.906,1.906 3.229,2.156 0.323,0.25 10 false Next 2.906,1.063 3.229,1.313 0.323,0.25 10 false Next 2.719,5.906 2.99,6.177 0.271,0.271 10 false End 2.906,5.375 3.198,5.646 0.292,0.271 10 false Exit 1.51,5.156 1.854,5.427 0.344,0.271 10 false Back 5.302,3.073 6.323,3.396 1.021,0.323 10 false Retrieving Error 1.333,2.729 3.25,3.052 1.917,0.323 10 false - Injector Compensation Code 1.333,3.094 4.198,3.417 2.865,0.323 10 false - Pilot Quantity Initial Learning Values 5.865,2.625 6.49,2.875 0.625,0.25 10 false Try Again 1.333,3.854 4.177,4.177 2.844,0.323 10 false - Crank Time Compensation Learning Values 1.333,3.469 4.198,3.792 2.865,0.323 10 false - Pilot Quantity Deterioration Learning Values

HINT:
A204047

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.


d.
A204044

Press "Next".


e.
A204045

Press "Next" again to proceed.


f.
A210594

Select the value to confirm and press "Next".


g.

When the next screen is displayed, confirm the contents and press "Exit".

A210595


Hide 2. LEARNING VALUES SAVE

This procedure uses the intelligent tester to save the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM in the intelligent tester depending on the components being replaced.

A209877E11
0.133,0.028 1.622,0.211 1.489,0.184 10 Learning Values Save: 3.236,0.609 3.591,0.760 0.355,0.151 10 Start 3.453,1.018 3.822,1.192 0.369,0.174 10 Next 3.453,1.858 3.822,2.033 0.369,0.174 10 Next 3.173,1.475 3.620,1.650 0.448,0.174 10 Notice 2.482,2.279 4.471,2.481 1.989,0.202 10 Select Replaced Component(s) 2.491,2.708 3.420,2.878 0.929,0.170 10 - Engine ECU 2.491,3.216 3.689,3.400 1.198,0.184 10 - Engine Assembly 2.491,3.738 3.712,3.913 1.221,0.174 10 - Injector Assembly 6.185,2.363 6.855,2.546 0.670,0.184 10 Try Again 5.685,2.858 6.712,3.032 1.026,0.174 10 Retrieving Error 3.056,4.338 3.397,4.517 0.341,0.179 10 Next 2.3,5.039 4.437,5.204 2.137,0.165 10 Learning Value(s) Save Complete 3.458,5.534 3.729,5.680 0.272,0.147 10 Exit 3.29,6.029 3.598,6.194 0.309,0.165 10 End 0.319,6.033 2.040,6.236 1.721,0.202 10 No Learning Value to Save 2.164,6.253 2.417,6.423 0.253,0.170 10 OK 4.91,5.263 5.561,5.442 0.651,0.179 10 Overwrite 5.625,5.048 6.813,5.213 1.188,0.165 10 Confirm Overwrite

HINT:
·

When replacing the engine assembly or the injector assembly together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the intelligent tester.

·
A204057

When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

·
A204058

A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.


d.
A204051

Press "Next".


e.
A204052

Press "Next" again to proceed.


f.
A211962

Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.


g.
A204055

If the overwrite confirmation screen is displayed, press "Overwrite".


h.
A204054

When the operation is finished, confirm the date and time of the save operation, and then press "Exit".


Hide 3. LEARNING VALUES WRITE

This procedure uses the intelligent tester to write all of the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the intelligent tester to the ECM.

A202034E29
0.094,0.052 1.583,0.396 1.49,0.344 10 false Learning Values Write: 2.677,0.635 3.021,0.906 0.344,0.271 10 false Start 2.625,1.49 3.063,1.771 0.438,0.281 10 false Notice 2.042,2.313 3.656,2.583 1.615,0.271 10 false Saved Date Confirmation 1.969,3.781 3.708,4.073 1.74,0.292 10 false Following Setting Complete 2.521,2.844 2.844,3.094 0.323,0.25 10 false Yes 2.458,4.24 2.781,4.49 0.323,0.25 10 false Next 2.458,1.896 2.781,2.146 0.323,0.25 10 false Next 2.896,1.042 3.219,1.292 0.323,0.25 10 false Next 5.26,5.313 5.552,5.583 0.292,0.271 10 false Exit 3.896,5.875 4.167,6.146 0.271,0.271 10 false End 2.531,5.313 2.823,5.583 0.292,0.271 10 false Exit 6.188,5.094 6.531,5.365 0.344,0.271 10 false Back 1.51,5.104 1.854,5.375 0.344,0.271 10 false Back 5.302,2.094 6.323,2.417 1.021,0.323 10 false Retrieving Error 5.865,1.646 6.49,1.896 0.625,0.25 10 false Try Again 5.26,2.521 6.385,2.844 1.125,0.323 10 false Writing Code Fail 4.313,1.417 5,1.677 0.688,0.26 10 false Data Error 4.365,1.156 4.927,1.417 0.563,0.26 10 false No Data 4.313,4.854 6.125,5.146 1.813,0.292 10 false Execute Following Functions 2.115,4.854 3.573,5.146 1.458,0.292 10 false All Setting(s) Complete

HINT:
A204063

A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.


d.
A204059

Press "Next".


e.
A204060

Press "Next" again to proceed.


f.
A204062

If the "Error Learning Values Write" screen indicating a problem with the saved values or that there are no saved values is displayed, perform "Learning Values Save" again.


g.
A204064

Confirm the date and time of the save operation, and then press "Yes".


h.
A204065

Confirm the contents, and then press "Next".


i.
A213405

If any instructions are displayed on the tester, manually perform the procedure to register each applicable compensation code or learning value in the ECM.


j.

Clear the DTCs.


Hide 4. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

NOTICE:
·

When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When an injector compensation code is input into the ECM, the pilot quantity learning values stored in the ECM are initialized. Also, DTC P1601 is stored when the pilot quantity learning values are initialized.



A141119E10
2.896,1.917 3.135,2.771 3.135,2.771 2.948,2.771 false 0.083,0.021 0.781,0.25 0.698,0.229 10 false Example: 1.198,2.688 3.031,2.875 1.833,0.188 10 false Injector Compensation Code

a.

After replacing one or more injectors assembly with new ones, input the compensation codes of the injector assemblies into the ECM as follows:

HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

·

When one or more injector assemblies are replaced, input the injector compensation codes, perform pilot quantity learning, and then clear the DTCs.

·

When the ignition switch is turned to ON after replacing the ECM, DTC P1601 is stored. This indicates that one or more injector compensation codes need to be registered. Manually clear the DTC upon completion of pilot quantity learning.



i.

Input the compensation codes, which are imprinted on the head portions of the new injector assemblies, into the intelligent tester.


ii.

Input the new compensation codes into the ECM using the tester.


iii.

Turn the tester off and turn the ignition switch off.


iv.

Wait for at least 30 seconds.


v.

Turn the ignition switch to ON and turn the tester on.


vi.

Perform pilot quantity learning.


vii.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If the DTCs are cleared without performing pilot quantity learning, DTC P1601 is stored immediately after clearing DTCs.




b.

Register compensation codes.

A202035E36
0.094,0.063 1.99,0.344 1.896,0.281 10 false Injector Compensation Code: 3.427,0.531 3.771,0.802 0.344,0.271 10 false Start 2.813,2.823 4.458,3.104 1.646,0.281 10 false Select Cylinder Number 3.646,3.229 3.969,3.469 0.323,0.24 10 false Next 3.104,2.063 4.198,2.344 1.094,0.281 10 false Select Function 3.646,2.479 3.969,2.729 0.323,0.25 10 false Next 3.385,1.323 3.823,1.604 0.438,0.281 10 false Notice 2.344,5.917 4.844,6.208 2.5,0.292 10 false Register Compensation Code Complete 3.25,4.552 3.573,4.802 0.323,0.25 10 false Next 3.646,1.719 3.969,1.969 0.323,0.25 10 false Next 3.646,0.948 3.969,1.198 0.323,0.25 10 false Next 3.469,7.042 3.75,7.323 0.281,0.281 10 false End 3.646,6.375 3.938,6.646 0.292,0.271 10 false Exit 1.771,6.146 2.115,6.427 0.344,0.281 10 false Next 1.594,4.906 2.927,5.229 1.333,0.323 10 false Invalid Number Input 0.854,5.198 1.479,5.448 0.625,0.25 10 false Try Again 4.417,4.875 5.375,5.208 0.958,0.333 10 false Compensation Failure 1.292,4.115 3.656,4.438 2.365,0.323 10 false Confirm Injector Compensation Code 1.292,3.75 4.031,4.073 2.74,0.323 10 false Input Injector Compensation Code Manually 5.573,5.198 6.198,5.448 0.625,0.25 10 false Try Again 5.135,3.896 5.781,4.219 0.646,0.323 10 false Keyboard 4.135,4.229 5.052,4.479 0.917,0.25 10 false OK or Cancel 4.385,3.719 4.75,3.969 0.365,0.25 10 false Input

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the tester on.


iv.
A208441

Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.


v.

Press "Next".


vi.
A208442

Press "Next" again to proceed.


vii.
A204039

Select "Set Compensation Code".


viii.

Press "Next".


ix.
A204040

Select the number of the cylinder corresponding to the injector compensation code that you want to register.


x.

Press "Next".


xi.
A204041

Register compensation code.

1.

Press "Input".

2.
A168951

Manually input the cylinder compensation code using the keyboard on the tester screen. The code is a 30-digit, alphanumeric value printed on the head portion of the injector assembly.

HINT:

Each injector compensation code is unique. The compensation code for each selected cylinder must be input into the tester correctly.


3.

Confirm that the compensation code for the selected cylinder is correct, and then press "OK".



xii.
A204042

Check that the compensation code displayed on the screen is correct by comparing it with the 30-digit alphanumeric value on the head portion of the injector assembly.

NOTICE:

If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.


HINT:
·

If an incorrect compensation code is input or read, return to the "Input Value" screen by pressing "Input".

·

The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.




xiii.

Press "Next" to register the compensation code in the ECM.

HINT:
·

If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

·

If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.




xiv.
A204043

If you want to continue with other compensation code registrations, press "Next". To finish the registration, press "Exit".


xv.

Turn the ignition switch off, and then turn the tester off.


xvi.

Wait for at least 30 seconds.


xvii.

Turn the ignition switch to ON, and then turn the tester on.


xviii.

Perform pilot quantity learning.


xix.

Clear DTC P1601 stored in the ECM using the tester (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If the DTCs are cleared without performing pilot quantity learning, DTC P1601 is stored immediately after clearing DTCs.




Hide 5. PILOT QUANTITY LEARNING

·

"Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

·

This procedure uses the intelligent tester to perform "Pilot Quantity Learning".

·

When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).


A204080E06
0.063,0.063 1.677,0.344 1.615,0.281 10 false Pilot Quantity Learning: 2.823,0.833 3.156,1.125 0.333,0.292 10 false Next 2.823,3.833 3.156,4.125 0.333,0.292 10 false Exit 2.813,2.75 3.146,3.042 0.333,0.292 10 false Next 2.813,1.656 3.146,1.948 0.333,0.292 10 false Next 1.854,1.208 3.656,1.552 1.802,0.344 10 false Wait until Learning Possible 2.583,0.385 2.917,0.677 0.333,0.292 10 false Start 1.219,2.344 4.24,2.635 3.021,0.292 10 false Operate Accelerator Pedal to Perform Learning 1.25,3.396 4.25,3.656 3,0.26 10 false Operate Accelerator Pedal to Perform Learning 2.625,4.25 2.927,4.469 0.302,0.219 10 false End 4.917,2.344 5.948,2.552 1.031,0.208 10 false Condition Error 4.948,3.385 5.979,3.594 1.031,0.208 10 false Condition Error 6.24,2.521 6.896,2.729 0.656,0.208 10 false Try Again 6.26,3.552 6.917,3.76 0.656,0.208 10 false Try Again

NOTICE:

After completing this procedure, clear the DTCs using the intelligent tester.


HINT:
·
A204031

If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

·

If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

·

If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

·
A204030

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning.


e.
A204025

Press "Next".


f.
A204026

Press "Next" again to proceed.


g.
A227766

Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is 70 kPa or more


NOTICE:
·

If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

·

If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.




ii.

If the atmospheric pressure is within the standard range, proceed to the next screen.



h.
A204027

Confirm the condition of the engine and wait until learning can be performed.

Essential Conditions for Learning
Tester Display Standard
Coolant Temp 70 to 100°C
Intake Air 10 to 120°C
Fuel Temperature 30 to 96°C
Fuel Return Temp 64 to 130°C
Battery Voltage 10 V or higher
Reju Pilot Quantity Learning READY

HINT:
·

If the values deviate from the standard above, "Pilot Quantity Learning" enters a standby state or is canceled.

·

When the essential conditions to perform learning are met, the screen will change automatically.



NOTICE:
·

Using the intelligent tester, make sure that DTCs other than DTC P1601 are not output.

·

If DTCs other than DTC P1601 are output, perform troubleshooting for those DTCs.



HINT:

DTC P1601 is stored when the value registered in the ECM for an input injector compensation code and/or pilot quantity deterioration learning value is the initial value.



i.
A204028

A204032

Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

HINT:
·

After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

·

It is possible to confirm the status of the learning operation during "Pilot Quantity Learning" by observing the blinking pattern of the glow indicator light.



Glow Indicator Light Blinking Pattern
Learning Status Glow Indicator Light Condition
Conditions essential to start learning have not been met Blinking at 0.5 second intervals
Conditions essential to start learning have been met Blinking at 1 second intervals
During racing (learning is being performed) Blinking at 1 second intervals
Learning is finished Off
Learning has been canceled Blinking at 1.5 second intervals
Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)

A178592E31
0.042,0.031 2.365,0.323 2.323,0.292 10 false Glow Indicator Light Blinking Pattern 0.083,0.802 0.354,1.042 0.271,0.24 10 false On 0.063,1.729 0.385,2.021 0.323,0.292 10 false Off 0.469,0.333 3.073,0.625 2.604,0.292 10 false Essential Conditions for Learning not Met 3.156,0.563 4.448,0.896 1.292,0.333 10 false Performing Learning 4.479,0.24 7.104,0.552 2.625,0.313 10 false Canceled (not due to injector malfunction) 1.24,1.781 2.031,2.104 0.792,0.323 10 false 0.5 seconds 4.01,2.094 4.802,2.417 0.792,0.323 10 false 1.5 seconds 3.625,1.781 4.417,2.073 0.792,0.292 10 false 1.5 seconds 2.948,1.771 3.604,2.073 0.656,0.302 10 false 1 second 1.323,2.104 2.115,2.427 0.792,0.323 10 false 0.5 seconds 3.115,2.083 3.771,2.385 0.656,0.302 10 false 1 second

A178593E26
1.656,1.115 1.313,1.844 false 3.281,1.229 2.479,1.823 false 5.792,1.031 5.594,1.854 false 0.792,2.917 1.01,2.917 false 0.792,2.917 0.927,2.708 false 2.594,2.708 3.177,2.708 false 3.177,2.708 2.813,2.917 false 0.115,0.104 6.479,0.469 6.365,0.365 10 false Glow Indicator Light Blinking Pattern (Learning Canceled Due to Cylinder 2 and 3 Injector Malfunction) 1.729,0.979 3.052,1.333 1.323,0.354 10 false Beginning of Cycle 3.01,0.594 3.552,0.917 0.542,0.323 10 false 1 Cycle 3.323,1.063 4.917,1.448 1.594,0.385 10 false Blinks 2 times to indicate problem with cylinder 2 5.833,0.948 7.021,1.302 1.188,0.354 10 false Beginning of Cycle 0.021,2.833 0.813,3.125 0.792,0.292 10 false 0.1 seconds 1.448,3.323 2.24,3.469 0.792,0.146 10 false 3.6 seconds 3.24,2.635 4.042,2.958 0.802,0.323 10 true 0.8 seconds 0.24,1.927 0.49,2.115 0.25,0.188 10 false On 0.24,2.469 0.573,2.635 0.333,0.167 10 false Off 4.708,2.823 5.5,2.969 0.792,0.146 10 false 2.4 seconds 2.823,3.292 3.615,3.438 0.792,0.146 10 false 2.3 seconds


j.
A204029

When the screen changes, push "Exit".


k.

Turn the ignition switch off, and then turn the tester off.


l.

Wait for at least 10 seconds.


m.

Turn the ignition switch to ON, and then turn the tester on.



o.

Turn the ignition switch off.

NOTICE:

Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.


HINT:
·

The main relay turns off after the learned value is stored in the ECM.

·

The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.




Hide 6. PILOT QUANTITY LEARNING (DETAIL)

·

"Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

It takes time to clear the learned values and perform learning for all cylinders.

·

This procedure uses the intelligent tester to perform "Pilot Quantity Learning (Detail)".

·

When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).


A204080E07
0.063,0.021 2.563,0.302 2.5,0.281 10 false Pilot Quantity Learning (Detail): 2.906,0.844 3.24,1.135 0.333,0.292 10 false Next 2.844,3.823 3.177,4.115 0.333,0.292 10 false Exit 2.833,2.781 3.167,3.073 0.333,0.292 10 false Next 2.865,1.667 3.198,1.958 0.333,0.292 10 false Next 1.844,1.177 3.646,1.521 1.802,0.344 10 false Wait until Learning Possible 2.604,0.396 2.938,0.688 0.333,0.292 10 false Start 1.25,2.323 4.333,2.615 3.083,0.292 10 false Operate Accelerator Pedal to Perform Learning 1.271,3.385 4.271,3.646 3,0.26 10 false Operate Accelerator Pedal to Perform Learning 2.604,4.26 2.938,4.479 0.333,0.219 10 false End 4.927,2.344 5.958,2.552 1.031,0.208 10 false Condition Error 4.927,3.385 5.958,3.594 1.031,0.208 10 false Condition Error 6.271,2.531 6.927,2.74 0.656,0.208 10 false Try Again 6.271,3.583 6.927,3.792 0.656,0.208 10 false Try Again

NOTICE:

After completing this procedure, clear the DTCs using the intelligent tester.


HINT:
·
A206037

If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning (Detail)" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

·

If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

·

If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

·
A206036

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning (Detail).


e.
A206032

Press "Next".


f.
A206033

Press "Next" again to proceed.


g.
A227771

Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is 70 kPa or more


NOTICE:
·

If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

·

If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.




ii.

If the atmospheric pressure is within the standard range, proceed to the next screen.



h.
A206034

Confirm the condition of the engine and wait until learning can be performed.

Essential Conditions for Learning
Tester Display Standard
Coolant Temp 70 to 100°C
Intake Air 10 to 120°C
Fuel Temperature 30 to 96°C
Fuel Return Temp 64 to 130°C
Battery Voltage 10 V or higher
Reju Pilot Quantity Learning READY

HINT:
·

If the values deviate from the standard above, "Pilot Quantity Learning (Detail)" enters a standby state or is canceled.

·

When the essential conditions to perform learning are met, the screen will change automatically.



NOTICE:
·

Using the intelligent tester, make sure that DTCs other than DTC P1601 are not output.

·

If DTCs other than DTC P1601 are output, perform troubleshooting for those DTCs.



HINT:

DTC P1601 is stored when the value registered in the ECM for an input injector compensation code and/or pilot quantity deterioration learning value is the initial value.



i.
A206035

A206038

Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

HINT:
·

After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

·

It is possible to confirm the status of the learning operation during "Pilot Quantity Learning (Detail)" by observing the blinking pattern of the glow indicator light.



Glow Indicator Light Blinking Pattern
Learning Status Glow Indicator Light Condition
Conditions essential to start learning have not been met Blinking at 0.5 second intervals
Conditions essential to start learning have been met Blinking at 1 second intervals
During racing (learning is being performed) Blinking at 1 second intervals
Learning is finished Off
Learning has been canceled Blinking at 1.5 second intervals
Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)

A178592E31
0.042,0.031 2.365,0.323 2.323,0.292 10 false Glow Indicator Light Blinking Pattern 0.083,0.802 0.354,1.042 0.271,0.24 10 false On 0.063,1.729 0.385,2.021 0.323,0.292 10 false Off 0.469,0.333 3.073,0.625 2.604,0.292 10 false Essential Conditions for Learning not Met 3.156,0.563 4.448,0.896 1.292,0.333 10 false Performing Learning 4.479,0.24 7.104,0.552 2.625,0.313 10 false Canceled (not due to injector malfunction) 1.24,1.781 2.031,2.104 0.792,0.323 10 false 0.5 seconds 4.01,2.094 4.802,2.417 0.792,0.323 10 false 1.5 seconds 3.625,1.781 4.417,2.073 0.792,0.292 10 false 1.5 seconds 2.948,1.771 3.604,2.073 0.656,0.302 10 false 1 second 1.323,2.104 2.115,2.427 0.792,0.323 10 false 0.5 seconds 3.115,2.083 3.771,2.385 0.656,0.302 10 false 1 second

A178593E26
1.656,1.115 1.313,1.844 false 3.281,1.229 2.479,1.823 false 5.792,1.031 5.594,1.854 false 0.792,2.917 1.01,2.917 false 0.792,2.917 0.927,2.708 false 2.594,2.708 3.177,2.708 false 3.177,2.708 2.813,2.917 false 0.115,0.104 6.479,0.469 6.365,0.365 10 false Glow Indicator Light Blinking Pattern (Learning Canceled Due to Cylinder 2 and 3 Injector Malfunction) 1.729,0.979 3.052,1.333 1.323,0.354 10 false Beginning of Cycle 3.01,0.594 3.552,0.917 0.542,0.323 10 false 1 Cycle 3.323,1.063 4.917,1.448 1.594,0.385 10 false Blinks 2 times to indicate problem with cylinder 2 5.833,0.948 7.021,1.302 1.188,0.354 10 false Beginning of Cycle 0.021,2.833 0.813,3.125 0.792,0.292 10 false 0.1 seconds 1.448,3.323 2.24,3.469 0.792,0.146 10 false 3.6 seconds 3.24,2.635 4.042,2.958 0.802,0.323 10 true 0.8 seconds 0.24,1.927 0.49,2.115 0.25,0.188 10 false On 0.24,2.469 0.573,2.635 0.333,0.167 10 false Off 4.708,2.823 5.5,2.969 0.792,0.146 10 false 2.4 seconds 2.823,3.292 3.615,3.438 0.792,0.146 10 false 2.3 seconds


j.
A206039

When the screen changes, push "Exit".


k.

Turn the ignition switch off, and then turn the tester off.


l.

Wait for at least 10 seconds.


m.

Turn the ignition switch to ON, and then turn the tester on.



o.

Turn the ignition switch off.

NOTICE:

Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.


HINT:
·

The main relay turns off after the learned value is stored in the ECM.

·

The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.




Hide 7. PILOT QUANTITY LEARNING VALUE CLEAR

HINT:
·

If the atmospheric pressure is below the threshold value, "Pilot Quantity Learning" will not be completed and DTC P1601 is stored. After "Pilot Quantity Learning Value Clear" is performed, DTC P1601 will not be stored.

·

Clear the learned values using the following procedure.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning Value Clear


d.
A227767

Press "Next".


e.
A227768

Confirm that the atmospheric pressure screen is displayed.

i.

Confirm the displayed atmospheric pressure.

Standard:

Atmosphere Pressure is below 70 kPa


NOTICE:
·

If the atmospheric pressure is higher than the standard range for performing "Pilot Quantity Learning Value Clear", do not clear the learned values. Instead, perform "Pilot Quantity Learning".

·

When the atmospheric pressure is higher than the standard range, perform "Pilot Quantity Learning" without initializing the learned values using "Pilot Quantity Learning Value Clear". If the learned values are initialized when the atmospheric pressure is higher than the standard range, the following symptoms may appear. Be sure to correctly follow procedures.

-

Driveability problems

-

Rough idle

-

Emission of white or black smoke, etc.





ii.

Proceed to the next screen.



f.
A227769

Select the cylinders whose learned value will be cleared.

NOTICE:
·

Multiple cylinders can be selected.

·

Only the cylinders for which fuel injector compensation codes have been written must have their learned value cleared.




g.

After selecting the cylinders whose learned value will be cleared, press "Next" to begin the initialization.


h.
A227770

When the screen changes, push "Exit".


i.

Turn the tester off and turn the ignition switch off.


j.

Wait for at least 10 seconds.


k.

Turn the ignition switch to ON, and then turn the tester on.



m.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


n.

Turn the ignition switch to ON for 1 second.


o.

Enter the following menus: Powertrain / Engine and ECT / DTC.


p.

Read the DTCs.


q.

Confirm that no DTCs are output.


Hide 8. DESCRIPTION OF VIN

NOTICE:

The Vehicle Identification Number (VIN) must be input into the replacement ECM.


HINT:

The VIN is a 17-digit alphanumeric number. An intelligent tester is required to register the VIN.


This registration section consists of two parts, Read VIN and Write VIN.

a.

Read VIN: Explains the VIN reading process in a flowchart. This process allows the Vin stored in the ECM to be read, in order to confirm that the two VINs, provided with the vehicle and stored in the vehicle's ECM, are the same.


b.

Write VIN: Explains the VIN writing process in a flowchart. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.


Hide 9. READ VIN

a.

Confirm the vehicle VIN.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Read.


Hide 10. WRITE VIN

a.

Confirm the vehicle VIN.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / VIN / VIN Write.