Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

P0560
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds or more The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

EFI-MAIN NO. 1 fuse

·

ECM



Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage at terminal BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A388914E01
1.281,3.76 2.354,3.958 1.073,0.198 10 false Battery 1.167,2.969 2.24,3.167 1.073,0.198 10 false FL 1.156,2.083 2.229,2.281 1.073,0.198 10 false P/I-B 2.688,1.656 3.76,1.854 1.073,0.198 10 false EFI-MAIN NO. 1 5.438,1.448 5.875,1.646 0.438,0.198 10 false G185 5.448,2.76 5.885,2.958 0.438,0.198 10 false C152 5.552,1.219 5.708,1.417 0.156,0.198 10 false 1 5.552,2.51 5.708,2.708 0.156,0.198 10 false 1 5.875,2.771 6.177,2.979 0.302,0.208 10 false E1 5.865,1.302 6.448,1.531 0.583,0.229 10 false BATT 6.031,3.646 6.552,3.833 0.521,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the engine switch is turned to on (IG), even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.



PROCEDURE

1.INSPECT BATTERY
a.

Inspect the battery (See page Power Source / Network>1GD-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

2.CHECK BATTERY TERMINAL

NG

8.RECHARGE OR REPLACE BATTERY
2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

3.CHECK ECM TERMINAL VOLTAGE (BATT)

NG

7.REPAIR OR REPLACE BATTERY TERMINAL
3.CHECK ECM TERMINAL VOLTAGE (BATT)
a.
U169477E01
3.229,0.969 2.635,1.781 false 2.313,1.802 2.979,1.99 0.667,0.188 10 false 1 (BATT) 2.854,0.417 3.292,0.604 0.438,0.188 10 false G185 0.177,0 0.844,0.188 0.667,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-1 (BATT) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

5.REPLACE ECM

B

END

5.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) for 3 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END