Refer to DTC P2454 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P2454).
For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
If P2453 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
If the vacuum hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine is running at 4000 rpm with no load for 10 seconds or more. | When the output voltage from the differential pressure sensor indicates a reversal of positive and negative pressure.
(1 trip detection logic) |
·
Incorrect air hose routing ·
Air hose is clogged ·
Blockage in vacuum pipe ·
Differential pressure sensor ·
ECM |
| DTC No. | Data List |
|---|---|
| P2453 | DPF Differential Pressure |
DTC P2454 (Diesel Particulate Filter Pressure Sensor "A" Circuit Low) and/or DTC P2455 (Diesel Particulate Filter Pressure Sensor "A" Circuit High) will be stored if there is an open or short malfunction in the differential pressure sensor circuit.
After confirming DTC P2453, check the differential pressure in "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" using the GTS.
| Condition | Differential Pressure Output | Sensor Condition |
|---|---|---|
| Engine switch on (IG) | Approximately 0 kPa | Normal |
| Always | -5 kPa or less or higher than 99 kPa | Open or short circuit |
| 4000 rpm (No engine load) | Negative output | Incorrect hose routing |
In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2453 is output | A |
| DTC P2453 and other DTCs are output | B |
If codes other than DTC P2453 are output, perform troubleshooting for those DTCs first.
A
B
Check if the air hose routing between the differential pressure sensor and vacuum pipe is correct (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>INSTALLATION).
Check that there is no exhaust gas leakage between the differential pressure sensor and vacuum pipe.
OK
NG
Be careful of being burned by exhaust gases during the following inspection.
Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.
Start the engine.
Check if there are exhaust gas pulsations from both air hoses during idling.
Exhaust gas pulsation exists.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.
Check that the differential pressure is as specified below.
| Condition | Differential Pressure Output | Sensor Condition |
|---|---|---|
| Engine switch on (IG) | Approximately 0 kPa | Normal |
OK
NG
NEXT
NEXT
Replace the differential pressure sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.
Check that the differential pressure is as specified below.
As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.
For reference result of real-vehicle check is as shown in the table below:
| Condition | DPF Differential Pressure |
|---|---|
| 2500 rpm without load | 0.5 kPa or more |
Start the engine.
Engine is running at 4000 rpm with no load for 10 seconds or more.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P2453.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.
NEXT