Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  


DESCRIPTION

Refer to DTC P200C (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P200C).

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures. (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).

·

If DTC P20CD is present, refer to the DTC table for Diesel Particulate Filter System (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).



P20CD
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 second With the exhaust fuel addition injector assembly off, the FIVO output is high for 3 seconds.
(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM



HINT:

DTC P200C, P200E, P20CF and/or P2428 will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVO) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVO signal, the ECM judges that the current has been applied to the exhaust fuel addition injector assembly.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVO are inconsistent.

A265674E05
2.723,3.191 3.069,3.370 0.347,0.179 10 ECM 1.226,0.886 1.556,1.026 0.330,0.140 10 CPU 1.418,1.537 1.812,1.696 0.394,0.159 10 FIVO 1.526,2.427 1.776,2.586 0.250,0.159 10 FIV 3.222,1.445 4.253,1.624 1.031,0.179 10 Monitor Circuit 3.184,2.328 4.292,2.507 1.108,0.179 10 Command Circuit 5.381,1.05 7.095,1.414 1.714,0.364 10 to Fuel Addition Injector Assembly

WIRING DIAGRAM

A388917E02
0.583,6.01 1.656,6.208 1.073,0.198 10 false Battery 2.938,6.104 4.604,6.302 1.667,0.198 10 false No. 1 Integration Relay 0.406,5.25 1.479,5.448 1.073,0.198 10 false FL 0.406,4.365 0.854,4.563 0.448,0.198 10 false P/I-B 1.719,3.875 2.167,4.073 0.448,0.198 10 false 1C 2.49,5.177 3.604,5.385 1.115,0.208 10 false EFI-MAIN NO. 1 4.208,4.042 4.938,4.25 0.729,0.208 10 false EFI NO. 2 4.99,5.365 5.438,5.563 0.448,0.198 10 false 1K 6.229,5.25 6.781,5.448 0.552,0.198 10 false MREL 5.813,5.375 6.26,5.573 0.448,0.198 10 false G184 6.438,6.083 6.885,6.281 0.448,0.198 10 false ECM 2.469,4.031 3.583,4.24 1.115,0.208 10 false EFI-MAIN NO. 2 1.729,5.365 2.177,5.563 0.448,0.198 10 false 1J 4.979,3.875 5.427,4.073 0.448,0.198 10 false 1K 3.49,4.542 4.604,4.75 1.115,0.208 10 false EFI MAIN 2 3.5,5.698 4.615,5.906 1.115,0.208 10 false EFI MAIN 1 1.76,3.677 1.917,3.875 0.156,0.198 10 false 1 4.99,3.688 5.146,3.885 0.156,0.198 10 false 22 1.771,5.167 1.927,5.365 0.156,0.198 10 false 3 5.021,5.156 5.177,5.354 0.156,0.198 10 false 7 5.896,5.167 6.052,5.365 0.156,0.198 10 false 14 4.427,1.229 4.583,1.427 0.156,0.198 10 false 1 3.031,1.229 3.188,1.427 0.156,0.198 10 false 2 3.177,1.469 4.292,1.677 1.115,0.208 10 false C126 3.177,1.646 5.76,1.865 2.583,0.219 10 false Exhaust Fuel Addition Injector Assembly 5.813,1.094 6.26,1.292 0.448,0.198 10 false G184 6.229,1.083 6.677,1.281 0.448,0.198 10 false FIV 5.896,0.885 6.052,1.083 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION).



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
U169132E01
0.396,0.198 0.615,0.385 0.219,0.188 10 false *a 0.531,1.104 0.896,1.25 0.365,0.146 10 false C126

Disconnect the exhaust fuel addition injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C126-2 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


c.

Reconnect the exhaust fuel addition injector assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C126-1 - G184-6 (FIV) Always Below 1 Ω
C126-1 or G184-6 (FIV) - Body ground and other terminal Always 10 kΩ or higher



d.

Reconnect the exhaust fuel addition injector assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
HINT:

If the voltage at the exhaust fuel addition injector assembly connector is not 11 to 14 V, repair or replace the harness and connector between the exhaust fuel addition injector assembly and No. 1 integration relay.


a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.

HINT:

The exhaust gas temperature increases to 250°C (482°F) or higher after driving the vehicle for 20 minutes.



d.

Turn the engine switch on (IG) for 3 seconds.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.



NEXT

END