Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › RELAY (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260472 RELAY(w/ Urea SCR System) G

1GD-FTV ENGINE CONTROL  RELAY(w/ Urea SCR System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 82641 1.INSPECT NO. 1 INTEGRATION RELAY

A353033E01
2.161,2.161 2.451,2.420 0.291,0.259 10 1J 3.941,2.159 4.232,2.418 0.291,0.259 10 1K 5.309,2.156 5.600,2.415 0.291,0.259 10 1C 2.081,2.129 2.414,2.331 0.333,0.202 3.874,2.127 4.208,2.329 0.333,0.202 5.237,2.124 5.57,2.326 0.333,0.202

Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)
- -

NOTICE:
·

The EDU relay, IG2 relay, EFI MAIN1 relay and EFI MAIN2 relay are built into the No. 1 integration relay.

·

Before performing the relay inspections for the relays of the No. 1 integration relay, inspect the EDU, IG2, EFI-MAIN NO. 1 and EFI-MAIN NO. 2 fuses.



a.

Inspect the EDU relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1J-5 Battery voltage not applied to terminals 1J-10 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-10 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



b.

Inspect the IG2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1J-7 Battery voltage not applied to terminals 1J-6 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-6 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



c.

Inspect the EFI MAIN1 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1J-10 Battery voltage not applied to terminals 1K-7 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1K-7 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



d.

Inspect the EFI MAIN2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1J-12 Battery voltage not applied to terminals 1J-10 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-10 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 896B1A 2.INSPECT DCU RELAY (DCU)

a.
A301376E03
2.344,0.771 2.656,0.469 2.656,0.469 2.719,0.469 false 2.313,1.458 2.063,1.75 2.063,1.75 1.979,1.75 false 1.917,1.115 1.656,1.115 false 2.688,1.104 3.021,1.104 false 0.292,1.313 0.438,1.49 0.146,0.177 10 false 1 1.271,1.302 1.417,1.479 0.146,0.177 10 false 2 0.302,0.781 0.448,0.958 0.146,0.177 10 false 3 1.281,0.781 1.427,0.958 0.146,0.177 10 false 5 2.76,0.396 2.906,0.573 0.146,0.177 10 false 1 1.875,1.667 2.021,1.844 0.146,0.177 10 false 2 1.49,1 1.635,1.177 0.146,0.177 10 false 3 3.073,1.021 3.219,1.198 0.146,0.177 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the DCU relay.


Hide 89463B 3.INSPECT NOx PM RELAY (NOx PM)

a.
A167865E10
1.99,0.719 1.531,0.365 false 2.667,0.677 3.073,0.302 false 2.542,1.125 3.073,1.125 false 2.542,1.625 3.083,1.625 false 0.198,0.74 0.333,0.99 0.135,0.25 10 false 5 1.198,0.781 1.365,0.99 0.167,0.208 10 false 3 0.208,1.302 0.365,1.594 0.156,0.292 10 false 2 1.198,1.281 1.385,1.5 0.188,0.219 10 false 1 1.396,0.229 1.583,0.448 0.188,0.219 10 false 1 3.115,0.188 3.271,0.479 0.156,0.292 10 false 2 3.146,1.531 3.313,1.74 0.167,0.208 10 false 3 3.146,1.031 3.281,1.281 0.135,0.25 10 false 5 0.083,0.073 0.615,0.292 0.531,0.219 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the NOx PM relay.