Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned to on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is turned to on (IG), the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A356868E01
0.66,4.881 1.166,5.042 0.506,0.161 10 Battery 2.717,4.728 4.183,4.903 1.466,0.175 10 No. 1 Integration Relay 6.107,2.964 6.509,3.159 0.403,0.195 10 ECM 4.315,0.563 4.679,0.758 0.365,0.195 10 CHK 5.621,0.536 5.869,0.730 0.248,0.195 10 W 4.767,0.463 4.960,0.624 0.193,0.161 10 7 4.208,3.119 4.373,3.280 0.165,0.161 10 7 4.713,3.793 4.878,3.954 0.165,0.161 10 6 2.075,3.799 2.240,3.960 0.165,0.161 10 3 5.552,3.877 5.718,4.039 0.165,0.161 10 8 6.107,2.808 6.520,2.969 0.413,0.161 10 G184 5.426,0.536 5.668,0.697 0.242,0.161 10 7 5.435,4.578 6.838,4.969 1.403,0.391 10 Power Management Control ECU 3.568,4.193 3.936,4.389 0.368,0.196 10 IG2 2.744,3.56 3.050,3.733 0.305,0.173 10 IG2 5.736,3.969 6.153,4.150 0.418,0.181 10 IG2D 5.435,4.415 5.808,4.587 0.374,0.172 10 G50 0.864,3.578 1.268,3.777 0.404,0.200 10 P/I-B 4.663,3.965 4.940,4.126 0.277,0.161 10 1J 2.879,0.64 3.153,0.801 0.274,0.161 10 G6 4.702,0.64 4.981,0.801 0.279,0.161 10 G7 2.896,0.466 3.122,0.628 0.225,0.161 10 28 3.183,0.547 3.597,0.747 0.415,0.200 10 IG+ 4.42,3.119 4.697,3.280 0.277,0.161 10 1J 2.024,3.409 2.301,3.571 0.277,0.161 10 1C 2.031,3.965 2.308,4.126 0.277,0.161 10 1J 2.068,3.236 2.233,3.397 0.165,0.161 10 1 1.725,1.661 2.418,1.878 0.692,0.217 10 GAUGE 2.957,1.167 4.945,1.414 1.988,0.247 10 Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the engine switch to on (IG).


b.

Check the illumination condition of the MIL.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B
Illuminates → Turns off C



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT ENGINE STARTS

C

2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result
Result Proceed to
DTC is not output A
Any DTCs is output B

HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.


Result
Result Proceed to
MIL remains on A
MIL does not illuminate B

d.

Reconnect the ECM connector.



A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (CHK) or G184-7 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT ENGINE STARTS
a.

Turn the engine switch to on (IG).


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (CHK) - G184-7 (W) Always Below 1 Ω



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR