The EGR valve position sensor is mounted on the electric EGR control valve assembly and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 5 seconds | EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic) |
·
Open or short in EGR valve position sensor circuit ·
Electric EGR control valve assembly (EGR valve position sensor) ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 5 seconds | EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic) |
·
Open or short in EGR valve position sensor circuit ·
Electric EGR control valve assembly (EGR valve position sensor) ·
ECM |
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.8 V for more than 2 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
Refer to DTC P042E (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P042E).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-31 (VCEG) - C151-24 (EEGL) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C151-25 (EGLS) - C151-24 (EEGL) | Engine switch on (IG) | 0.6 to 1.4 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT
(See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
Disconnect the electric EGR control valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C127-3 (VC) - C127-1 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to Electric EGR control valve assembly) |
Reconnect the electric EGR control valve assembly connector.
OK
NG
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C127-3 (VC) - C151-31 (VCEG) | Always | Below 1 Ω |
| C127-2 (VTA) - C151-25 (EGLS) | Always | Below 1 Ω |
| C127-1 (E2) - C151-24 (EEGL) | Always | Below 1 Ω |
| C127-3 (VC) or C151-31 (VCEG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C127-2 (VTA) or C151-25 (EGLS) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the electric EGR control valve assembly connector.
Reconnect the ECM connector.
OK
NG
Disconnect the electric EGR control valve assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C127-3 (VC) - C127-2 (VTA) | Engine switch off | No short or open |
| C127-2 (VTA) - C127-1 (E2) |
| *a | Front view of wire harness connector
(to Electric EGR control valve assembly) |
Reconnect the electric EGR control valve assembly connector.
OK
NG
Replace the electric EGR control valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch on (IG) for 2 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT