Refer to DTC P0545 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0545).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine. | No. 2 exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses ·
Coolant temperature is 70°C (158°F) or more ·
The exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds. |
·
Open or short in No. 2 exhaust gas temperature sensor circuit ·
No. 2 exhaust gas temperature sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine. | No. 2 exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses ·
Engine is running ·
Coolant temperature is 60°C (140°F) or more |
·
Open or short in No. 2 exhaust gas temperature sensor circuit ·
No. 2 exhaust gas temperature sensor ·
ECM |
| DTC No. | Data List |
|---|---|
| P2032
P2033 |
Exhaust Temperature B1S2 |
DTC P20CF (Exhaust fuel addition injector malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.
Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
When DTC P2032 or P2033 is output, check the exhaust gas temperature indicated by "Powertrain / Engine and ECT / Exhaust Temperature B1S2 using the GTS.
| Condition | Exhaust Temperature B1S2 | No. 2 Exhaust Gas Temperature Sensor Condition |
|---|---|---|
| Idling after warm-up | Constant at between 50 and 700°C (122 and 1292°F) | Normal |
| 0°C (32°F) | Open circuit | |
| 1000°C (1832°F) or higher | Short circuit |
The ECM constantly monitors the output voltages from the No. 2 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.
Refer to DTC P0545 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0545).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.
Read the value.
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
| Temperature Displayed | Proceed to |
|---|---|
| 0°C (32°F) (After warming up the engine) | A |
| 1000°C (1832°F) or higher | B |
| OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm | C |
If there is a short circuit, the GTS will indicate 0°C (32°F).
If there is an open circuit, the GTS will indicate 1000°C (1832°F) or higher.
A
B
C
Disconnect the No. 2 exhaust gas temperature sensor connector.
Connect terminals 1 (E2) and 2 (THCI) of the exhaust gas temperature sensor wire harness side connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.
Read the value.
1000°C (1832°F) or higher
| *1 | No. 2 Exhaust Gas Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor) |
Reconnect the exhaust gas temperature sensor connector.
OK
NG
Replace the No. 2 exhaust gas temperature sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for Front)>REMOVAL).
NEXT
Disconnect the No. 2 exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C166-1 (E2) - C149-24 (ETCI) | Always | Below 1 Ω |
| C166-2 (THCI) - C149-25 (THCI) | Always | Below 1 Ω |
Reconnect the No. 2 exhaust gas temperature sensor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Disconnect the No. 2 exhaust gas temperature sensor connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.
Read the value.
0°C (32°F)
| *1 | No. 2 Exhaust Gas Temperature Sensor |
| *2 | ECM |
Reconnect the No. 2 exhaust gas temperature sensor connector.
OK
NG
Replace the No. 2 exhaust gas temperature sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for Front)>REMOVAL).
NEXT
Disconnect the No. 2 exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C166-2 (THCI) or C149-25 (THCI) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the No. 2 exhaust gas temperature sensor connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT