Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer operates after the engine switch is turned off. When a certain amount of time has elapsed after turning the engine switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A356862E01
2.966,2.583 3.240,2.753 0.274,0.170 10 IG2 4.868,0.42 5.279,0.590 0.411,0.170 10 IGSW 5.756,5.154 6.120,5.324 0.364,0.170 10 ECM 4.397,4.34 4.809,4.510 0.411,0.170 10 MREL 4.849,2.621 5.353,2.791 0.504,0.170 10 +B 3,4.761 3.857,4.932 0.857,0.171 10 EFI MAIN1 5.048,0.821 6.047,1.151 0.999,0.330 10 Soak Timer IC 5.44,2.79 6.633,3.119 1.193,0.330 10 Power Source IC 5.261,4.062 6.071,4.367 0.810,0.305 10 MAIN Relay Control IC 2.133,2.405 2.407,2.575 0.274,0.170 10 IG2 0.545,6.055 1.410,6.244 0.865,0.189 10 Battery 0.421,5.129 1.279,5.318 0.859,0.189 10 P/I-B 1.881,3.729 3.001,4.085 1.119,0.356 10 EFI-MAIN NO. 1 0.237,2.178 1.557,2.527 1.320,0.349 10 Power Management Control ECU 2.236,5.327 3.822,5.652 1.586,0.325 10 No. 1 Integration Relay 4.849,3.056 5.353,3.226 0.504,0.170 10 +B2 4.849,3.457 5.353,3.627 0.504,0.170 10 +B3 0.69,1.77 1.195,1.940 0.505,0.170 10 IG2D

P2610
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
- ECM internal malfunction (2 trip detection logic). ECM

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the engine switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the engine switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the engine switch is turned to on (IG).


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and wait for 10 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


h.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END